I want some advice for making my system more secure. I want deactivate any network connection that is unnecessary. Only my browser and the update ability of zypper should have access to the internet. On windows there are personal firewalls.
How can I block internetaccess for all other programmes on openSUSE?
Many of you know how important is the analysis and planning of the targeted environment before the attempt of a successful penetration test. I got the idea, and I am trying to draw the network design in order to visualize things better. Many tools can be used to do that, I used hping3 as it comes with BT4, my favorite dist for pentesting, others include tcptraceroute, firewalk-5.0 (discontinued by developers...), etc.
What in fact is done by the program (hping3) is TCP/IP packet injection (with the SYN bit enabled) hop-by-hop until it reaches the final host (destination). By sniffing the traffic, I could determine the TTL of the various responding hosts within the path until my packet "got there".
As far as I know the default behavior of a network would be to decrement the TTL of a device as long as I go deeper on the network (meaning that I am getting closer the targetet IP). Like, for example, in a network with 3 devices (routers) before my targetet IP it would be something like this:
Quote:
123.123.123.123 TTL 255 (my gateway)
123.123.123.133 TTL 254
123.123.123.143 TTL 253
177.177.177.177 TTL 124 (target IP)
Demonstrating that the host is Windows based (TTL starts at 128) and is placed 4 hops from me. What I know by the notice though, is that sometimes the TTL increases. Likewise:
[Code]...
I suspect this is an initial configuration bug. All firewall logs seem to be going to all
three files. That causes a lot of clutter in the log files, and makes it difficult to see whether there are any serious problems being logged.
I run a small (cabled) network between a desktop with XP with two printers hooked to it and a laptop with Ubuntu 10.04.1 64b. I can approach and use these printers from my laptop and filesharing works also. BUT ... this only works when my Ubuntu firewall (Gufw 10.04.5) is switched off. I am operating behind my router_modem which has a hardware type of firewall switched on at all times so I presume I'm safe. Now my questions:
1. Is this really safe enough?
2. What kind of settings would Gufw need to be able to use it AND use my mini-network for printing? I have no experience whatsoever with firewall rules and settings.
I have a domain name relik.ath.cx with a mud and an html page and now Im working on my own personal mail server preferably with the first email on it [URL].
View 6 Replies View RelatedI currently want to set up a network with 2 Ubuntu servers (mail and web) in a DMZ in order to separate them from an internal network. I want to use a dedicated Linux firewall. This firewall will have 3 network interfaces on it. One network interface will connect to the external router/modem (router and modem in one box), one interface will connect to the DMZ and the other interface will connect to the internal network. The router/modem lets you put, I think it's 1 or 2, interfaces in a DMZ.
But, when I think of any of the dedicated firewall's or servers' interfaces it doesn't make sense to me to put any of them in the router/modem's DMZ (I think it would be better for the dedicated firewall's and the servers' interfaces to have static private I.Ps ie 192.168.2.4 etc right?). What I mean is that even if, as far as the router/modem is concerned, none of the interfaces were in a DMZ, the area where the servers are would still effectively be a perimeter network and with such a set up would still be, effectively,a DMZ, right?
I have Ubuntu 8.04 as virtual host. On this host I have installed VirtualBox virtualization software. I have installed Windows XP as virtual machine and installed HTTP server.I would like temporally disable all network connections to host and virtual machine.So on Ubuntu host I have set firewall settings:
Code:
sudo iptables -F (to flush - delete all firewall settings)
sudo iptables -P INPUT DROP (to disable all input traffic)
[code]....
I want to know the details about the implementation of distributed firewall in a local area network
View 5 Replies View RelatedInstalled a security update for samba tonight via Opensuse updater.Now, when trying to access my home network an authentication box pops up (never used to)Asks me to enter authentication for my home network.I enter my username and password and hit enter. After a few seconds the authentication box pops up again askingfor the same indicating I have entered the wrong username / password combination (which I know I have not).
View 9 Replies View RelatedRecommend open source tools that can help in figuring out if we are experiencing a network latency due to the newly installed firewall on our server.
View 1 Replies View RelatedThe network manager will ask me for my security key and it will not accept it. Instead when I use the show password feature to see what I typed in was correct, it shows something completely different than what I typed. For instance if my Key was :when it pops up and ask to for me to retype it again it shows something completely different in hex. Is there anyway I can use a different network manager?
View 8 Replies View RelatedI am trying to add a custom allow rule in the firewall for a range of IPs from 74.201.102.0 - 74.201.103.255, what exactly am I supposed to enter in the source box? I believe I have to add two separate rules for 102 and 103, and I put /24 at the end of both, is this correct to get the whole range of IPs?
View 3 Replies View Related1. Under openSUSE 11.2, I allowed printer sharing through CUPS by setting the Firewall to Allow Services of CUPS in the External Zone section. I don't see the CUPS option in the Allow Services of the Firewall under 11.4, any zone. Is my system missing something?2. If I turn off the Firewall, the client computer can see the printers, even get the broadcasted names. If I put port 631 in TCP of the Advanced setting of the External Zone, the client computer can see the printer too, but I know I read somewhere that putting 631 in the External Zone is basically allowing printer requests from the entire internet.
View 2 Replies View Relatedswitched recently to 11.2 and it works fine for me as workstation I want to set up a router separating a part of the network and also acting as a firewall/proxy... Configured 2 Ethernet Interfaces, checked Ip forwarding in Yast but it does not forward the packets from the "internal" to the "external" network. Hovewer after I set up my router as default for machines on internal network I can ping the external interface but no adress on external network (particularly the one of the default router) !!! From the router I can reach both networks and the net via default gateway on external. Tried to:
a) switch firewall completely off
b) iptables -P FORWARD ACCEPT
c) masquarading internal adresses to the external network
my interfaces configuration looks like:
eth0 Link encap:Ethernet HWaddr 00:13:D4:E3:A2:7B
inet addr:192.168.1.34 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::213:d4ff:fee3:a27b/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[Code].....
We have reason to ask this of you following some strange firewall behaviour - But don't panic If you use openSUSE 11.2 and you think: Your Firewall should be running You are not sure but think it should be check and report back here.
This is how to check:
Go to Yast > Security and Users > Firewall
I did a shields up test and it told me that 1056 ports were stealth but that my pc responded to ping and was visible on the net. How do i fix this?
View 4 Replies View RelatedI can't get my openvpn work if the firewall is on , and I also don't see any option to allow openvpn service in firewall allow service.
View 1 Replies View RelatedI'm trying to get OpenMPI (a parallel programming library) working on my home system. I have just two machines on it now, t61 and quad, connected through a router. (Which is also connected to cable modem for internet.) I can ssh between the machnes, mount directories with NFS, etc. However, I just can't get the OpenMPI to run. The OpenMPI message board suggested that the most probable cause is that the firewall is blocking TCP. I don't know how to tell if that's the problem, and can't find any manual for the SuSE firewall, while the various Wikis &c that pop up in a search don't provide any information that addresses my problem.
View 9 Replies View RelatedOk here's my setup :
SuSE 10.0 X86 32 acting as my internet gateway and firewall.
eth0 is my internal interface network 192.168.0.0/24 IP 192.168.0.254 dsl0 is my internet connection and is a single ip PtP connection to my ISP.
My internal network is masquaraded onto the external network.
I run an smtp server on my gateway box that I need to be accessable to both the internal and external networks.
However I want to prevent machines on the internal network from establishing connections to external smtp servers, but still alow them to connect to the smtp server on the gateway to send email.
NOTE I do not want to force attempts to connect to [URL] 25 to be re-directed to my internal server I just want to drop or reject the connection.
The firewall up until now has just been configured through YaST, but am not afraid to edit script files if needed
The reason for doing this it to prevent spambots from being able to send through my isp, I keep my own machines clean but sometimes get asked to disinfect machines for other people (family members etc), where I need to connect to the outside world to get updates/virus defs etc, but don't want them spamming from my network.
can I deny the access to my server for a specific OS? I have one PC which I want to give it acces from winxp, but if it's boot into ubuntu I want to deny all access to my server, same IP, same ethernet card
View 8 Replies View RelatedI've setup vnc over ssh tunnelling however the Suse firewall seems to be blocking it. On the local host I have this in ~/.ssh/config:LocalForward localhost:5900 remotehost.com:5900 The problem is that this only works when I either disable the firewall or add an exception for VNC. Both of these actions defeat the whole purpose of ssh tunnelling since they leave my VNC port open to the outside world (very insecure).
View 2 Replies View RelatedI'm in the situation where I'm trying to create 2 private networks using ESX server, all behind a NAT router (static ips are used). I used an openSuse11 vm as a router and was able to configure it so that a machine on one private network was able to access the public network. The problem I have now it that I need to be able to access a machine on the private network from the public network using a different set of IP's.
So if a machine in the private network has an IP of 10.1.0.222 I should be able to ping it using 10.99.0.222 or some other IP. I have never done this before and after reading up on iptables and linux routing I feel more confused than before. Is it possible to add IPs to eth0 (public) and have them mapped to machines on a private network eth1 or eth
I'm looking forward to the release of openSUSE 11.4, which I'm looking to install as an Internet facing gateway on a mini-ITX machine with 2 Ethernet cards. As such I've been reading up on the YaST Firewall trying to find out to configure it, and there's one thing I'd like to be able to do: 'stealth' all the firewall ports.
In other words, if someone were to hypothetically do a port scan of my external IP address, I would rather they not know whether any of the ports on my gateway are open or closed, so instead of replying with the status of those ports the packets get dropped. I've been able to do this with a product called Astaro Security Gateway, which I currently have installed on a second hand Dell Optiplex machine, but I am now looking into the possibility of installing this as a virtual machine inside an openSUSE 11.4 host (extra level of security) and would like the same functionality for the host OS.
How I can refuse an outgoing connection on opensuse firewall by default outbound policy is permissive, and the p2p I explicitly deny an outgoing, according to protocol, remote port and local port.
But I can add rules as how to run opensuse firewall rules are permissive only for inbound traffic and so I can not specifically deny an outgoing connection.
Before using fwbuilder is very powerful and configurable but now I'm with suse for convenience but want to know if you can do what I want, if not I will have to use fwbuilder.
I have done a new install of 11.4 and as with previous versions, I have to go to YAST2 and disable the firewall before I have internet and local network access. Finally I must find out how to do this correctly.
How to I change the default firewall to allow me internet and local network access without disabling it completely? Also I am unclear about the function of Novel Network Armor? What does this do?
Samba is working correctly if Susefirewall2 is off. I have added Samba client and Samba Services for extern access but samba is not working when firewall is now on. Which services should I also add ?
View 1 Replies View RelatedI tryed to setup a second IP address with yast on a openSUSE 11.2 on eth0 as eth0:2nd but with a different firewall zone. But SUSE firewall just see eth0.
I want to define with services are available on with IP address. Also with custom rules I can't specify a destination IP.
So now can I do this with yast? Or have I todo this manually without SUSE firewall?
I have a couple of openSUSE 11.2 machines and each is directly connected to the Internet (they are not behind a router, firewall, etc). I want them to be able to communicate without any firewall restrictions, but keep the firewall rules for all other IP addresses. Is this possible? the software package I'm trying to use randomly chooses a port to use in the range of 32768-61000 and I don't feel comfortable having a port range that wide open on both machines.
View 5 Replies View RelatedI have properly configured my router to open a port for Transmission and Vuze. The OpenSuSE firewall settings are somewhat confusing, however. How do I add a port specifically for the BT protocol? I know it's the firewall causing issues, because when I shut it down, my BT apps roar to life, and die with a whimper when I turn it back on. In Ubuntu, opening a port in the router is automatically configured in the firewall; that is apparently not the case with this distro.
So, when I go to Yast Firewall, I see "allowed services" under the tabs available. When I hit that tab, I see a dropdown menu that contains services such as NetBios Server and Samba Server. Am I choosing one of those available and adding a port to it? Am I adding a custom service via the Advanced settings, and if so, why isn't there a way to label the service so that it shows up under allowed services?
.i need to configure squid in my company how to install and configure squid in my SUSE server...
View 2 Replies View Related