OpenSUSE Network :: CISCO Vpnclient - Invalid Module Format
Sep 7, 2010
I am trying to compile the Cisco vpnclient on my Opensuse 11.2 and (after some troubles) I got the module compiled and installed but when I try to load with insmod I got this error
<</etc/init.d/vpnclient_init start
Starting /opt/cisco-vpnclient/bin/vpnclient: insmod: error inserting '/lib/modules/2.6.31.12-0.2-default/CiscoVPN/cisco_ipsec.ko': -1 Invalid module format
Failed (insmod)>>
I am able to use the vpnclient forcing the module with modprobe -f cisco_ipsec but I'd prefer to solve the 'invalid format' original problem. I 'googled' around and it seems related with this warning during vpn_install script "WARNING: Symbol version dump /usr/src/linux-2.6.31.12-0.2/Module.symvers is missing; modules will have no dependencies and modversions." I have these rmps:........
View 2 Replies
ADVERTISEMENT
Jul 29, 2010
i installed SLES 11 sp1 as guest on openSUSE 11.3 host, then change the adapter network from 'NAT' to 'Bridged Adapter', but when i hit start i got this error message: Failed to open a session for the virtual machine sles. Failed to open/create the internal network 'HostInterfaceNetworking-wlan0' (VERR_SUPDRV_COMPONENT_NOT_FOUND). Failed to attach the network LUN (VERR_SUPDRV_COMPONENT_NOT_FOUND). One of the kernel modules was not successfully loaded. Make sure that no kernel modules from an older version of VirtualBox exist. Then try to recompile and reload the kernel modules by executing '/etc/init.d/vboxdrv setup' as root (VERR_SUPDRV_COMPONENT_NOT_FOUND). but when run: sudo /etc/init.d/vboxdrv setup
[Code]....
View 2 Replies
View Related
Jan 10, 2010
I have a problem with loading the powersaving kernel module p4-clockmod.ko. When I try inserting the module (via modprobe or insmod) I get FATAL: Error inserting p4_clockmod (/lib/modules/2.6.31.8-mediaserver/extra/p4-clockmod.ko): Invalid module format The module has been compiled together with the kernel. Other modules load with no problem at all. I've tried recompiling the kernel (after re-installing the sources, make xconfig from scratch) - no avail. There's only one kernel source package installed. Searching the forum and google didn't yield a helping answer.
View 9 Replies
View Related
Jun 1, 2009
When I try to load the Realtek 8187 modules to kernel using the ./wlan1up command, I get the following error:
[root@localhost rtl8187_linux_26.1025.0328.2007]# ./wlan1up
insmod: error inserting 'ieee80211_crypt-rtl.ko': -1 File exists
[code]...
Can someone tell me how to correct the "Invalid module format"? I hope that correcting the "Invalid module format" error, I will not have the "Unknown symbol in module" error.
Note: I am using wlan1 for this module as I previously am online with the wlan0 network.The same error occurs if I use ./wlan0up.
View 3 Replies
View Related
May 24, 2009
I'm new to openSUSE and as a matter of fact, to linux too. I've got a Linksys WUSB600N wireless adapter which used to work fine with some live versions of linux that I was testing out before moving onto suse... Each time, upon booting using live CDs, I used to copy the driver I had downloaded from:
SpeedShare - Download rt2870-kernel-2.6.24-nemesis.tar.bz2
Then 'make' and get into the driver's os/linux directory to load the driver using 'insmod rt2870sta.ko' Now, upon doing a 'make' and 'make install', followed by the 'insmod rt2870sta.ko', I get the error saying:
insmod: error inserting 'rt2870sta.ko': -1 Invalid module format
I tried doing 'modprobe -rv rt2870sta' and didn't get any error messages. But while doing 'modprobe -v', this error shows up: insmod /lib/modules/2.6.27.7-9-default/kernel/drivers/net/wireless/rt2870sta.ko
FATAL: Error inserting rt2870sta (/lib/modules/2.6.27.7-9-default/kernel/drivers/net/wireless/rt2870sta.ko): Invalid module format
View 7 Replies
View Related
Jun 8, 2010
i'm unable to get the cisco vpnclient installed on lucid 10.4.I have tried a few guides from the 9.05 and even 8.10 but most of them require patches that are for them kernal versions i'm unable to find anything for 10.4 patch wise. anybody come across this yet and more importantly did you win ?
View 1 Replies
View Related
Jun 22, 2011
With hello kernel module, i use two types of Makefile, one is using kernel build system:
obj-m += hello.o
all:
make -C /lib/modules/$(shell uname -r)/build M=$(PWD) modules
module loads successfully; another is using (CC) and then creating the module by "make -C /lib/modules/$(shell uname -r)/build M=$(PWD) modules", this module gives the error message when it is inserted, .........
View 5 Replies
View Related
Jan 20, 2010
I've got a brand new Advantech USB 4761 Digital/Analog PC Lab card. They claim to run under Linux. The install, " dpkg -i advdaq_1.04.0006-1_i386.deb", was successful. But when I tried to modify and run their install script, "adv_load_template", I get this:./adv_load_templateinsmod: error inserting './modules/advdrv_core.ko': -1 Invalid module format insmod: error inserting './modules/usb4761.ko': -1 Invalid module format
View 1 Replies
View Related
Mar 4, 2011
I successfully built the sources for 64 bit linux drivers from [URL].... on the 64 bit F14 machine: Linux localhost.localdomain 2.6.35.6-45.fc14.x86_64 #1 SMP Mon Oct 18 23:57:44 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux and got wl.ko:
[Code]...
View 2 Replies
View Related
Apr 18, 2010
I am using reliance zte modem ac2726.i inserted the modem in my laptop and tried wvdialconf command and it was working.but when i type
Code:
modprobe usbserial vendor=0x19d2 product=0xfffd
command it shows the following error message
Code:
FATAL: Error inserting usbserial (/lib/modules/2.6.29.4-167.fc11.i686.PAE/kernel/drivers/usb/serial/usbserial.ko): Invalid module format
But "cat /proc/bus/usb/devices","lsusb","dmesg" everything are working perfectly."Wvdial.conf" file also got configured perfectly.what can i do now?
View 3 Replies
View Related
Jan 25, 2011
A little background first: Wireless card: Broadcom BCM4312 Wireless driver used: [URL].... (and slackbuild variation of the same)
GFX card: nVidia geForce 7150m I installed Slackware yesterday, along side my Ubuntu (yes yes, I use Ubuntu lol. I've been using it for about four years, I added Slackware to grub.cfg, using the OS prober, which added four menu entries. The first two caused kernel panic, the third worked, and I don't think I tried the fourth. (I'm pretty sure they were, in this order: generic, generic-smp, huge, and huge-smp). Using huge, I could not modprobe my wireless driver, I would get a "Invalid Module Format" error with wl, and when installing the nVidia drivers (from their site), I would get:
[code]....
I then booted using a menuentry my friend gave me, created my initrd, and everything worked fine, both graphics and wireless (mostly fine). So I upgraded to -current, kernel 2.6.35.10, and I started getting the same errors as before, 'Invalid Module format' and the same thing with the nVidia drivers, although this time, it happens regardless of if I use the generic kernel, or the huge kernel. I've done heaps of Google'ing around, and nothing I found worked.
View 8 Replies
View Related
Mar 13, 2010
I'm having some troubles with nfsd in slackware-current. When I start the service, I get the following error messages: Quote:
WARNING: Error inserting sunrpc (/lib/modules/2.6.33-smp/kernel/net/sunrpc/sunrpc.ko): Invalid module format
WARNING: Error inserting auth_rpcgss (/lib/modules/2.6.33-smp/kernel/net/sunrpc/auth_gss/auth_rpcgss.ko): Invalid module format
WARNING: Error inserting lockd (/lib/modules/2.6.33-smp/kernel/fs/lockd/lockd.ko): Invalid module format
FATAL: Error inserting nfsd (/lib/modules/2.6.33-smp/kernel/fs/nfsd/nfsd.ko): Invalid module format
The mount fails from the clients with the error message: Quote: mount.nfs: access denied by server while mounting jupiter:/media/Backup A look at syslog from the server side gives: Quote: exportfs: exports duplicate symbol exportfs_decode_fh (owned by kernel) mountd[28198]: getfh failed: No such device kernel: exportfs: exports duplicate symbol exportfs_decode_fh (owned by kernel)
View 3 Replies
View Related
Feb 22, 2010
What is the error "invalid module format" and the message "insert kernel module" mean? And whats the reason for the same?
View 8 Replies
View Related
Sep 27, 2010
I was installing opensuse on the c partition and it gave errors so i aborted it now i click on windows and it says invalid or unsupported executable format chainloader +1 so then i proceeded to try and fix this by changing the menu.lst to this:
And now it tells me that disk isnt found so i need to know what to put in the menu.lst to load the actual windows partition and then fix the original error.
View 9 Replies
View Related
Dec 19, 2009
I just installed a fresh copy of 11.2 I use networkmanager and the cisco vpn plugin (not the cisco client). I create a vpn profile and connect to it. The icon shows a connection has been established, but I have no network connectivity. In the /var/log/NetworkManager file, I see this
Code:
Dec 19 13:28:08 TonyLaptop nm-dispatcher.action: Script '/etc/NetworkManager/dispatcher.d/netcontrol_services' exited with error status 127.
When I sudo vpnc and connect that way, it works fine, it connects and I can pass traffic.
I am using opensuse 11.2x86
firewall is disabled
Gnome
View 3 Replies
View Related
Aug 10, 2010
I have a new install of an OpenSuse 11.3 server and I do not see the IPSec Support option when I use Yast to set that I up. I have the firewall setup with 2 interfaces, one external and one internal and that is all working fine. When I connect via my laptop and connect in via a Cisco IPSec VPN, I get connected, but no traffic goes through.
I did search through the forums, but I don't see any hits related to the issue I'm facing. I installed the ipsec-tools, but I am still not seeing the IPSec Support in the firewall section of Yast that I see noted on many Google Searches. Is there a package or something configuration that is needed to get IPSec Support for VPN setup?
View 2 Replies
View Related
Aug 16, 2011
Bottom Line: Dvd Drive died in my toshiba laptop and it was replaced (not before tech for some reason reformatted the Win7 partition... which was 100% un-needed, but thats beside the point now. I redid win7 (the tech installed vista) and am TRYING to "redo grub". Facts: The Slackware AND Ubuntu Partitions ARE STILL THERE and when i use SuperGrub Boot CD (which doesn't restore my grub by itself) to boot into slackware, i can see ALL THE CONTENT of both Linuxes still there including grub on ubuntu partition
(Tri-Boot: Ubuntu, Slackware, and WIn7) I had it working for two years or so, SO i know this "setup" works fine. I am A) Trying to do this as simply as possible. B) Trying to avoid the need to download a 800MB ISO (as seen for this issue on this forum) and trying not to have to reformat Ubuntu Partition (though I have the .Debs I have downloaded for it backed up ... all 1.7GB of them) I have /dev/sda1 as win7, /dev/sda2 as Slack and /dev/sda3 as Ubuntu (which contains Grub Legacy).. Every command I do seems to result in an error like "invalid command" or "invalid Execution format " (i think that second one is right) type errors. I compiled (awhile back) a few kernels for Slackware, but feel goofy that I cant figure what i this out (what i thought was going to be a "2 minute" fix)
View 4 Replies
View Related
Mar 6, 2010
So I made the upgrade to slackware64-current and all of a sudden after my next reboot, startx failed, and x refused to start the output was the following:
Code:
Release Date: 2010-02-16
X Protocol Version 11, Revision 0
Build Operating System: Slackware 13.1 Slackware Linux Project
Current Operating System: Linux hd830 2.6.33 #3 SMP Sat Feb 27 19:42:32 CST 2010 x86_64
Kernel command line: BOOT_IMAGE=Linux ro root=803 vt.default_utf8=0
Build Date: 23 February 2010 12:09:32PM
Current version of pixman: 0.16.6
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sat Mar 6 19:21:18 2010
(==) Using default built-in configuration (30 lines)
(EE) Failed to load module "fbdev" (module does not exist, 0)
WARNING: Error inserting button (/lib/modules/2.6.33/kernel/drivers/acpi/button.ko): Invalid module format
WARNING: Error inserting i2c_algo_bit (/lib/modules/2.6.33/kernel/drivers/i2c/algos/i2c-algo-bit.ko): Invalid module format
WARNING: Error inserting agpgart (/lib/modules/2.6.33/kernel/drivers/char/agp/agpgart.ko): Invalid module format
WARNING: Error inserting drm (/lib/modules/2.6.33/kernel/drivers/gpu/drm/drm.ko): Invalid module format
WARNING: Error inserting drm_kms_helper (/lib/modules/2.6.33/kernel/drivers/gpu/drm/drm_kms_helper.ko): Invalid module format
FATAL: Error inserting i915 (/lib/modules/2.6.33/kernel/drivers/gpu/drm/i915/i915.ko): Invalid module format
(EE) intel(0): No kernel modesetting driver detected.
(EE) Screen(s) found, but none have a usable configuration.
Fatal server error:
no screens found
Please consult the The X.Org Foundation support. Please also check the log file at "/var/log/Xorg.0.log" for additional information. So then after some googling I got the suggestion to downgrade udev-151 to udev-141, but that yeilded no results. So I did some more googling and a bunch of people who had the same problem said that downgrading module-init-tools worked, so I downgraded from module-init-tools 3.11 something to 3.6 and now, not only does my X no longer work, but no modules are being loaded I believe, for example I saw in my startup that fuse was not being loaded, ndiswrapper which I had installed was not loaded.
View 7 Replies
View Related
Aug 16, 2010
I have an old Dell Optiplex GX240 running Windows XP hooked up to my Olevia HDTV. I'd like to format this computer and install Ubuntu 10.04.After burning the Ubuntu install disk, I hook the computer to the tv via HDMI and reboot to the CDROM but upon booting I receive an 'Invalid Format' error and no video is shown.I did some searching - there is very little info about this problem. This post http://ubuntuforums.org/showthread.php?t=1063217 seems to indicate that the solution is to hook up the computer to an old CRT monitor, then after the computer has booted, switch the HDMI cable to the tv.This solution is unsatisfactory. Does anyone have experience with this problem? Is there another way to get around this problem?
View 1 Replies
View Related
Apr 7, 2010
I'm using linux suse 9.3. Recently i try to run execution files but it shows an error try running with the option "-console" or "-silent" When I tried with the -console option, I got the error - The wizard cannot continue because of the following error: Invalid command line option: console is not supported (1001) (403)
[Code]...
View 1 Replies
View Related
Dec 13, 2010
We are using LPC3250 ARM9 and LTIB for building the Linux 2.6.27.8 We have written some code to access GPIO and was working earlier with opensuse 9.0 We now have fedora 11 32 bit 2.6.30.10-105.2.23.fc11.i686.PAE When we make the program we get following errors we are using GCC3.4.5
#make -C /lib/modules/`uname -r`/build M=`pwd` modules
make -C /home/shekhar/lpc3250/ltib/rpm/BUILD/linux-2.6.27.8 M=`pwd` modules
make[1]: Entering directory
`/home/shekhar/lpc3250/ltib/rpm/BUILD/linux-2.6.27.8'
CC [M] /home/shekhar/samsung_lcd/gpio/char.o
cc1: error: invalid option `64'
[code]....
View 1 Replies
View Related
Oct 17, 2009
I compiled a fresh install of httpd on a new linux box, added a virtual hosts entry for an https site, but when I try to start apache I get the error:
Code:
Invalid command 'SSLEngine', perhaps misspelled or defined by a module not included in the server configuration Is this because I don't have mod_ssl compiled in?
View 3 Replies
View Related
Jun 25, 2010
I've searched all over the internet and have found numerous threads on this topic, none of which have helped me fix the problem. I'll post as much info I can about my setup.I have 3 hard drives... one is for ubuntu (9.10), one is for my data, and one is for Windows7. It looks like this:
1st drive (hda) = ubuntu
2nd drive (hdb) = data
3rd drive (hdc) = windows
[code]....
View 6 Replies
View Related
Apr 4, 2009
I have installed win xp(sda1) win 2003(sda2), centos 5 (sda7) and mint 5(sda5) on 4 partitions and swap (sda6).All OS work fine except centos 5. When from the boot menu I choose Centos 5, I get the following error:File system type is ext2fs, partition type 8x83.Kernel /boot/vmlinuz 2.6.18.92.el5xem root/dev/sda7Error 13 invalid or unsupprted excecutable formatBut I 'm sur that I have format /dev/sda7 as ext3
View 2 Replies
View Related
Sep 1, 2010
I'm currently running 11.2 and I configured Proxy settings in the YaST module. It seems that when I use a proxy I have problems updating. It can retrieve some files, but while getting others it fails. Furthermore, I can't establish a connection with the timeserver in the YaST -> NTP configuration module.
My question is if there have been changes from this version to 11.3 regarding the Proxy settings.
View 1 Replies
View Related
Oct 28, 2010
I am trying to setup a scenario where I am able to control the access to certain html files. I'd like forbid access to the URL: url
my iptables rule in "SuSEfirewall2-custom" looks like:
iptables -I INPUT -j DROP -p tcp -m string --string ".*test.*" -algo bm
--dport $port
As a result, I get:
#> rcSuSEfirewall2 start
Starting Firewall Initialization (phase 2 of 2) Bad argument `--string'
(same for "-string")
View 5 Replies
View Related
Jul 18, 2010
I am getting following error "Invalid command 'ProxyHTMLEnable', perhaps misspelled or defined by a module not included in the server configuration" Saw this thread in /etc/apache2/mods-enabled/ I see
[Code]...
View 6 Replies
View Related
May 1, 2010
I am getting this error when trying to start apache. This is on a server that was functioning but now, when I tried to restart the server, this error shows up when trying to start the httpd service. The command that is causing the error is: CustomLoglogs/rosewood.access combined However, my guess is that it has something to do with either a module not being loaded or something wrong with the setup. But, as I said, this server was running so I am really not sure what changed. Server is Apache 2.0.52.
View 2 Replies
View Related
May 16, 2010
I've been googling all afternoon to fix this error I get. The situation is as follows: I have multiple harddrives (3x320gb and 1x160gb) all on the SATA interface. One of these drives contains Windows, and the rest I use for programs and downloads. I've installed Ubuntu 9.04 from a USB-stick using the installer's partitioner to make some room for Ubuntu (Ext4 filesystem). I've tried Ubuntu and SUSE in the past.
View 1 Replies
View Related
Aug 4, 2010
Ubuntu 9.04 server (64bit)
8GB
(2) 320 WD HDD - RAID 1
After coming home one evening I found my server was turned off. My suspicions lead me to believe we had a storm and the power went off, then the UPS went off and finally at that point the server went off too. I think my server was set to allow security updates. After it turned of and restarted it seems it made a change to Grub and upgraded it to Grub2. In doing so I now get the following message:
Error 13: Invalid or un supported executable format
I have tried to do the following:
url
This solved the problem for me, from > url
Quote:boot from the live medium and chroot into the Linux installation:
$ sudo mkdir /mnt/linux
$ sudo mount -t ext4 /dev/sda1 /mnt/linux
code....
Then, the following command should resolve the issue. :
$ sudo grub-install --recheck /dev/sda
View 4 Replies
View Related
