I'm trying to get my Adaptec RAID 6405 working on fresh Opensuse 11.4.I need to make a driver/module for this because aacraid module doesn't see the raid controller.
modinfo aacraid
filename: /lib/modules/2.6.37.6-0.5-default/kernel/drivers/scsi/aacraid/aacraid.ko
version: 1.1-5[26400]-ms
[code]....
How to make a driver/module for a fresh opensuse 11.4 installation ?
I am trying to install FC 10 on my built-in Adaptec raid controller and the Live CD does not see the controller.From my other ATA drive FC10 install I get this from lspci -v:
Code:
00:1f.2 RAID bus controller: Intel Corporation 6300ESB SATA RAID Controller (rev 02) (prog-if 8f)
Subsystem: Super Micro Computer Inc Device 5180
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 18
I/O ports at e200 [size=8]
[code]...
sdb and sdc are the SATA raid disks... they have already been partitioned as a single raid 0 device... not sure why / how they stil show up as two disks.
Am installing Fedora 10 on an old but good server that used to be a windows box. It has 2 sata disk raid level 1 on adaptec 2410SA card. Disks are clean no info even did a low level format and recreated RAID.. twice DVD boots and installs os on raid array and reports success. new volume appears under computer icon but cannot be mounted after reboot attempt reports Reading physical volumes. This may take a while... (it doesn't)
Volume group "VolGroup00" not found
Unable to acces resume device (/dev/VolGroup00/LogVol01)
mount: error mounting /dev/root on /ysroot as ext3: No such file or directory
input: PS/2 Generic Mouse as /devices/platform/i8042/serio1/input/input4
and then a blinking cursor with keyboard echo but its just copying reboot with install DVD does not show previous (unmountable) disk image and repeat of above process increases operator need for alcohol have "disable write cache for drives" as I found that is a post but after fedora install.I do not know what grub is for instance but once linux is booted (on other computers) I can muddle through ok in terminal mode.
I'm trying to install the nVidia driver for a fresh Installation of OpenSUSE 11.4 (32-bit) but I'm running into some issues. I followed the instructions (SDB:NVIDIA the hard way - openSUSE) using the driver binary mentioned in the workaround link (NVIDIA DRIVERS 256.53 Certified) but the installer fails while building the kernel module with the following errors:
Code:
nvidia-installer log file '/var/log/nvidia-installer.log'
creation time: Sun Mar 13 17:32:56 2011
[code]....
I was trying to update the drive for my adaptec raid controller. Unfortunately, Adaptec only provides RPM packages. So I converted the package using alien. After dpkg install, I then tried using dkms to build the module:
Code:
root@atulsatom# dkms add -m aacraid -v 1.1.5.26400
Adding driver was successful, but I got some error during the build
Code:
root@atulsatom# dkms build -m aacraid -v 1.1.5.26400
Kernel preparation unnecessary for this kernel. Skipping.
[Code]...
Has anyone successfully used an Adaptec 2100S in a RAID configuration? Specifically, RAID1?
Drivers exist for earlier version of Red Hat, but building an using a driver disk results in the error:
Driver disk is invalid for this release of CentOS
CentOS does not recognize the adapter out-of-the-box as a HW RAID controller, but does recognize the individual disks.
I attempted to use software RAID, but the installer craps-out after a while and the screen locks up.
I installed on a Intel SR2612UR Server with integrated LSI Expander and a Adaptec 5805Z controller a Raid 6 Array with 12x 2TB Drives (2 ext4 Partition: 16TB, 2TB), but I get very poor read speed depending on the blocksize that I set it vary between 130 MB/s and maximally 170 MB/s which is really poor for a Raid 6 Array of 12 drives, on a similar Dell Server I get above 650 MB/s. The Adaptec Controller has the latest Firmware installed.
View 1 Replies View RelatedI'm running 10.04 x86 server with a really simple installation on a single 250GB boot disk. I then have a RAID5 array as /dev/md0 (set up using mdadm with x4 2TB disks). All is working well. My mdadm.conf file looks like this
Code:
# mdadm.conf
#
# Please refer to mdadm.conf(5) for information about this file.
[code]....
if I was to lose the boot disk and need to remount the RAID array on a fresh installation, what steps do I need to go through. My assumption is that the superblocks on the RAID disks will be used and I don't need to keep any additional information - is this right?
I had ubu 904 and vista installed on an 80gb drive, i had a spare 80gb drive also. I setup a raid0 config in my bios, then installed ubu9.10 onto it. All was fine until the very end, and then it said grub failed to install.
So i rebooted, and im left with a blinking cursor. How do i install grub? Ive installed ubu a few times now and never had an issue so now im lost.
My problem is that I'm trying to install CentOS 5.4 x86_64 DVD ISO on Supermicro X7SBI server with installed Adaptec RAID 3405 controller.
I created RAID 5 array and is working fine (adaptec status says Optimal) but I can't install CentOS to that array (1.5TB size).
Whenever I try to install with: linux dd
I'm asked for a driver, which I have downloaded from Adaptec site and extracted contents to USB drive (in installation found as /sba1) which has now a lot of IMG and some ISO files on it.
I try to load (I simplified names) RHEL5.img, CENTOS.img... with x64 names (one exact name: aacraid driverdisk-CentOS-x86_64.img) and I always get the error message: "No devices of the appropriate type were found on this driver disk"
This is going on for a week now and I can't find the right driver or something I'm doing wrong to get install done.
I have loaded openSuSE 11.4 on an IBM x3400 box with an Adaptec ServeRAID 8k-l SAS harddisk adapter. openSuSE 11.1 was previously loaded on this box and was using XEN kernels.) The default "desktop" kernel boots and operates correctly. I use this machine to run other XEN virtual machines to run different versions or our companies printer controller application. When I attempt to boot the xen kernel, the kernel cannot locate the root partition (or any other partition) on the hard disk. Here are a few lines of kernel output:
[code].....
I am installing Kubuntu AMD64 10.04 on a 500GB Hardware raid1. After the install completes, the computer will try booting, but grub says "No such disk."
The motherboard specs are Here,
I have tried installing to this raid three times, each returning the results mentioned above. Does anyone know what is going on?
I'm installing a file server on Lenny (Samba on RAID5, nothing exotic)
First, I installed on a basic SATA drive, to check everything else in the system was recognized correctly. Success.
Then, I added my 3405 Adaptec board, with a 3 drive RAID5, and reinstalled, still on the lone SATA disk.
Install runs ok, shows correctly the 3405 board, detects the logical drive alongside with the SATA drive. Smooth. I install Lenny on the SATA drive, planning to use the RAID5 for later partitioning and data storage. During install, the SATA disk is shown as SCSI-1 and the RAID5 disk as SCSI-2. Again, install completes correctly.
But on reboot and after selecting the default config, the system complains it can't find /dev/sda1!
If I remove the 3405 board, Lenny boots fine.
Is the presence of the Adaptec board and RAID5 drive changing the numbering of the disks, so that the SATA disk is no longer seen as /dev/sda1 ?
Following some problems of kernel upgrade, I have resinstalled my system. I now have some issues with sound. CD are recognized and played but no sound is coming out of my speakers (tested with amarok and caffeine). Same thing on .....: I see the video and get no sound.
However, I can hear the test sound form Configure Desktop / Multimedia
Any clue about what is going on?
After spending a full day messing with my dual monitors displays-should-not-be-cloned-by-default, I have now come to the sound. The config looks like the 11.3 setup (I alternate partitions from one install to the next), but all I get is silence. KMix won't run. Amrok is silent. "Sound Configuration" gets me to a window showing two cards I know nothing about. I've got an nVIDIA chip on the mother board and the two cards listed are "M2N72-D w/ snd-hda-intel" and "Creative Tech, Ltd. w/ snd-usb-audio". I'd have gone back to 11.3 where this stuff works, but my configuration files were all auto-updated and don't really work any more. I guess I ought to have archived the config files, but I didn't and I'm here now.
lspci shows:
Code:
00:07.0 Audio device: nVidia Corporation MCP72XE/MCP72P/MCP78U/MCP78S High Definition Audio (rev a1)
and some /var/log/messages entries:
Code:
Mar 14 14:18:22 beethoven kernel: [ 1120.311164] usbcore: deregistering interface driver snd-usb-audio
Mar 14 14:18:22 beethoven pulseaudio[21051]: pid.c: Stale PID file, overwriting.
Mar 14 14:18:22 beethoven pulseaudio[21102]: pid.c: Daemon already running.
Mar 14 14:18:22 beethoven kernel: [ 1120.800722] usbcore: registered new interface driver snd-usb-audio
Mar 14 14:18:38 beethoven pulseaudio[26008]: pid.c: Daemon already running.
Mar 14 14:18:39 beethoven pulseaudio[30854]: pid.c: Stale PID file, overwriting.
Mar 14 14:18:40 beethoven pulseaudio[30904]: pid.c: Daemon already running.
Mar 14 14:19:40 beethoven pulseaudio[30854]: ratelimit.c: 7 events suppressed
Mar 14 14:21:39 beethoven pulseaudio[30854]: ratelimit.c: 44 events suppressed
Mar 14 14:35:11 beethoven pulseaudio[30854]: ratelimit.c: 176 events suppressed
Mar 14 14:46:35 beethoven pulseaudio[30854]: ratelimit.c: 38 events suppressed
with duplicate events suppressed with ellipses by hand.
I have a client with a pair of Supermicro 6025B-T servers that he wants to have Ubuntu 10.10 64bit Server running on for VM/Cloud experimenting. He needs these to be set up RAID 10. I can go into the Adaptec utility and make the array and make it bootable and get to the point in the installer where it asks me if I want to use the SATA array - then it gets to the partitioning screen and the array is nowhere to be found.
View 1 Replies View RelatedI have tried to install openSuse several times and the same problem would persistRight after installation, when the prompt to log in shows up, I enter a username and a password, but it says that login failed. I am sure I type in the correct data as I have written down the username and the password I register during the installation.Also, after the installation finishes, the computer restarts automatically, though instead of restarting it goes into a mode similar to stand by. The screen is blank and the media buttons of the keyboard are lit, but nothing happens, so I just restart manually. Could this have something to do with it
View 2 Replies View RelatedI installed openSUSE today using a network installer cd, opting for the Xfce environment. Everything went smooth with the installer, but I have some issues with the network. After the fresh install, nm-applet did not start. I got the following error:
Code:
nm-applet
** Message: applet now removed from the notification area
** Message: applet now embedded in the notification area
** (nm-applet:14981): WARNING **: Fallback icon 'gtk-dialog-error' missing: (0) Icon 'gtk-dialog-error' not present in theme
**
ERROR:applet.c:2800:nma_icons_reload: assertion failed: (applet->fallback_icon) Aborted I don't know if the problem was with the applet or with the daemon. Fortunately I used Archlinux for a quite long time and I know how to connect to WPA2 encrypted wireless network from command line, so I was able to connect to the internet and do an upgrade - everything went just smooth and fine again.
After the update and restart, I found the nm-applet icon in the system tray. And here comes the second problem: I can connect with the nm-applet, but the connection does lasts only for about 10 seconds. So practically I can't use the net this way either. Ok, no problem, I fired up Yast, disabled the networkmanager and choose to start my network with the traditional method. I entered the required stuff from my wireless card ( ESSID and passwd ), set to activate at boot time and reboot.....
First of all here's my PC configuration
Proc Core2Duo 6750
MB MSI P35 Neo 2
RAM Corsair 4GB
Video Gigabyte GTS250
HDD 2x320GB Seagate in RAID 0 and 1GB WD
I have a Windows 7 installation with a boot partition on the RAID. I also want to have a dual boot with openSUSE 11.2 but I don't know how to set correctly my partitions. I have some unallocated space next to the Windows C: partition. When I try to install openSUSE it makes a suggestion to create some partitions that i don't need and don't want, and even doesn't mount them. It also creates a / 80GB, /boot 36MB, swap 2GB and /home 20GB partitions, so I am in lack of free space.
I don't know how to create screenshots during installation. Maybe I'll try to reinstall later and pick some screens in english, because my system language is bulgarian.
I am trying to install 11.2 on a system with RAID-1 /boot partition and RAID-10 /(root) partition. I have done this before with 10.3 but am hitting a wall with 11.2. In particular, the boot image loads and then halts when it tries to load the RAID-10 root partition saying that the personality is not laoded. modprobe shows that the raid10 module does not appear to be part of the boot image. I cannot find anything in the installation that will allow me to specify a module to include in the init image. How do I tell the installer to include an additional module?
View 3 Replies View RelatedI have run Ubuntu in the past and then switched to OpenSUSE several months ago and set up raid 0 on a 500gb hard drive and 700gb hard drive (I went with openSUSE because of the graphical raid setup.)
My whole partition setup looks like this:
500gb Hard Drive:
750gb Hard Drive:
md0 is the two 400gb partitions on each drive for a total of 800gb space on my /home partition ext4 filesystem ( 380gb space used ) md1 is 100gb ext4 / partition.
all raid 0
Now I was wondering if I downloaded the alternate install cd for ubuntu ( as OpenSUSE has crashed for the second time because of bad updates ( starts, but gets to terminal only ) ) would I be able to keep my raid 0 home partition and wipe the rest of the each drive and setting up Ubuntu keeping all of my files and settings intact, just to install my programs I need all while keeping my old settings ( such as firefox bookmarks, virtual box utilities etc. ) intact.
From what I know it's possible, but I don't know much about the Ubuntu Alternate install disk ( as I have been dealing with dependancy hell on OpenSUSE ) but in OpenSUSE it wont let me keep the old raid setup ( md0 ) Im guessing it is possible to set up the home directory on a different hard drive and then going back into the live cd, editing the fstab, and switching it to md0, if this is even possible, or would I need to configure the driver on that system before I did that Oh and I forgot to mention that I've only been running 64bit operating systems.
System Specs: AMD Dual core at 2.8ghz ( overclocked, stable, cpu ran at full bore for a day. only reaching 120f) Nvidia 9600 gso 368mb ram, 4gb ram at 800mhz
I've installed openSuse 11.4 server-mode (text only) on my desktop, and I'm trying to configure IceWM so i'll eventually have it set up so it always boots into text only mode, but I could be able to quickly start icewm via the command line.using Yast, I installed the Xorg server, and icewm.when I type X, the screen goes black and it just doesn't seem to do anythingI found if I hit ctrl+alt+f1 it kinda puts me back into text only mode, but I can't put in commands anymore. The last thing it says on the screen is:
Failed to load module "fglrx" (module does not exist, 0)
I've goggled that error message and the discussions that popped up around it made no sense to me at all. I've never configured X from scratch before, can someone point me towards a tutorial or something?
I have installed Ubuntu on my m1530 since 8.04 and currently dual boot Win7 and 10.10. I would like to dual boot on my PC, but I have run into a problem. I am not a pro at Ubuntu, but this problem I can not solve by reading forums like I have in the past.
I realize this is a common problem, but I have noticed people having success.
I have a M4A87TD EVO MB with two Seagate drives in Raid 0. (The raid controller is a SB850 on that MB) I use the raid utility to create the raid drive that Windows7x64 uses. I have 2 partitions and 1 unused space. Partition 1 is Windows, partition 2 is for media, and the remaining unused space is for Ubuntu.
I am running ubuntu-10.10-desktop-amd64 off a Cruzer 16GB flash drive that was installed via Universal-USB-Installer-1.8.1.4.
My problem like so many others is that when I load into Ubuntu, gparted detects two separate hard drives instead of the raid. I read that this is because kpartx is not installed on 10.10. I then went in LiveCD mode and downloaded kpartx from Synaptic Manager. Gparted still reported two drives. I opened terminal and run a few commands with kpartx. I received an error. (Forgive me I didn't write it down, but I believe it said something about a communication error. I will try again later and see.)
Currently I am reflashing the Cruzer with a persistence of 4GB. I am not familiar with this process, but I understand that my LiveCD boot will save information I download to it. I decided to try this method because I was going to install kpartx and reboot to see if this made a difference.
I am looking for any suggestions on a different method or perhaps someone to tell me that the raid controller or some hardware isn't supported. I did install ubuntu-10.10-alternate-amd64 on my flash drive, but fail to get past detecting my CD-ROM drive since it's not plugged in. If this method is viable, I will plug it in. I also watched the ..... video were a guy creates Raid 0 with the alternated CD, but it wasn't a dual boot and didn't use a raid controller from a MB.
I'll have a Sony VAIO AR290 with 2 HDD, earlier I'll have a Windows XP and SUSE and RAID was turned off. Now I turn on RAID in STRIPE mode for better productivity, Windows 7 installation was successful, It creates MBR partition (100 M and C: HDD. During SUSE installation(I've chose all parameters- swap and partition) installation process stop at 1% on "operating with HDD" and my VAIO dont answer on any key pressed (alt ctr del, ctr c, esc) and I'll should to turn it power off. During surfing web, I'll find some solutions to solve it by creating root partition but It hasn't any results.
View 7 Replies View RelatedOK Trying a fresh install of bnome openSuse, and I have certainly screwwed something up again and hope I don't have to reinstall again., arghhhh! Tomboy won't open, even after reinstallation, and below is the error, but first, as well I can't open my .odt file with openoffice writer!
now the error... #tomboy Gtk-Message: Failed to load module "canberra-gtk-module": libcanberra-gtk-module.so: cannot open shared object file: No such file or directory Gtk-Message: Failed to load module "gnomebreakpad": libgnomebreakpad.so: cannot open shared object file: No such file or directory ...and lots more
Could any RAID gurus kindly assist me on the following RAID-5 issue?I have an mdadm-created RAID5 array consisting of 4 discs. One of the discs was dropping out, so I decided to replace it. Somehow, this went terribly wrong and I succeeded in marking two of the drives as faulty, and the re-adding them as spare.
Now the array is (logically) no longer able to start:
mdadm: Not enough devices to start the array.Degraded and can't create RAID ,auto stop RAID [md1]
I was able to examine the disks though:
Code:
root@127.0.0.1:/etc# mdadm --examine /dev/sdb2
/dev/sdb2:
Magic : a92b4efc
Version : 00.90.00
code....
Code:
mdadm --create --assume-clean --level=5 --raid-devices=4 /dev/sda2 /dev/sdb2 /dev/sdc2 /dev/sdd2
As I don't want to ruin the maybe small chance I have left to rescue my data, I would like to hear the input of this wise community.
It's been a real battle, but I am getting close.I won't go into all the details of the fight that I have had, but I've almost made it to the finish line. Here is the set up. ASUS Z8PE-D18 mother board 2 CPU, 8 Gig Ram. I recently added an OCZ Agility SSD, defined a raid 1 virtual disk on the 1 terabyte WD HDD drives, which will holds all of my user data, the SSD is for executables.The bios is set to AHCI. Windows 7 installed fine, recognizes the raid VD just fine.
I installed Ubuntu 10.04 by first booting into try and mode, then opening a terminal and issuing a "sudo dmraid -ay" command. Then performing the install. I told it to install the raid components, and told it to let me specify the partitions manually. When setting up the partitions, I told it to use the free space I set aside on the SSD from the Windows 7 install as ext4 and to mount root there. Ubuntu installed just fine, grub2 comes up just fine, and Windows 7 boots with out a hitch, recognizing the mirrored partition as I indicated previously. When I tell grub to boot linux however, it pauses and I get the "no block devices found" message. It will then boot, but it does not recognize the raid array. After Ubuntu starts up I can run "dmraid -ay" and it recognizes the raid array, but shows the two component disks of the raid array as well. It will not allow the component disks to be mounted, but they show up which is annoying. (I can live with that if I have to)
I have fixed a similar problem before by setting up a dmraid script in /etc/initramfs-tools/scripts/local-top ... following the instructions found at the bottom of this blog:[URL].. To recap: My problem is that after grub2 fires up Ubuntu 10.04.1 LTS (Lucid Lynx), it pauses, and I get "no block devices found" It then boots but does not recognize the raid array untill I manually run "dmraid -ay". I've hunted around for what to do but I have not found anything. It may be some timing issue or something, but I am so tired of beating my head against this wall.
I have a little problem with Fedora and an Adaptec Raid5805. In the same system, if I use a hard disk in ich10 without connect the 5805 I can boot from cd and install Fedora, but when I connect the 5805 the live cd don't start and I can't boot the system. I test the same system in Debian, Gentoo, Ubuntu and the system start well without problems.
View 1 Replies View RelatedThis may be a no brainer and often repeated questionBut i will ask again.I need to install XP and openSUSE 11.3 onto a fresh diskShould i install XP first and then SUSE or the other way around
View 9 Replies View RelatedI have the latest version of Debian installed on a Poweredge 1600SC. Everything is working ok, but the Adaptec AAR 2410sa PCI SATA card has started being a bit weird. I have a 1TB drive connected to it and noticed that occasionally it was unmounting the drive and messages appeared in the /var/log/messages like the following:
Jun 10 23:50:57 servertron kernel: [11246.006500] sd 1:0:2:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
Jun 10 23:50:57 servertron kernel: [11246.006500] sd 1:0:2:0: [sdd] Sense Key : Hardware Error [current]
Jun 10 23:50:57 servertron kernel: [11246.006500] sd 1:0:2:0: [sdd] Add. Sense: Internal target failure
After a reboot everything would be fine. I did some research and heard that it could be the drive failing, so after running a disk check etc I connected up a new 1TB drive (was getting low anyway) to another SATA interface on the card and started trying to copy from one drive to another. Lo and behold, it happened on the new drive as well. Bugger.
I haven't had time to open it up and check the connections and will be doing this shortly, but thought I would check to see if it was using the best/newest driver, but am a bit stuck as to where to start. I've looked through some docs and help but can't really see how to update and check hardware drivers in debian.
lspci shows the following:
00:00.0 Host bridge: Broadcom GCNB-LE Host Bridge (rev 01)
00:00.1 Host bridge: Broadcom GCNB-LE Host Bridge
00:02.0 Ethernet controller: Intel Corporation 82540EM Gigabit Ethernet Controller (rev 02)
[code]....
Is there a newer version of accraid I can use? Even if there isn't, how would I go about identifying which driver the card is using and installing an update?