Networking :: Eth0 Is Not Working In RHEL5
Sep 8, 2010
I have installed RHEL-5 (2.6.18-53) on my Desktop (ASUS Motherboard with Realtek PCIe GBE Family Controler 8168). After installation eth0 is not detecting. I downloaded R8168 drivers from Relatek site, but I am unable to install as it's throwing the following error.
Wed Sep 8 21:49:41 IST 2010
make -C src/ clean
make[1]: Entering directory `/root/Desktop/REALTEK/r8168-8.019.00/src'
rm -rf *.o *.ko *~ core* .dep* .*.d .*.cmd *.mod.c *.a *.s .*.flags .tmp_versions Module.symvers Modules.symvers Module.markers *.order
[Code]......
View 3 Replies
ADVERTISEMENT
Mar 9, 2011
how to remove the network alias (ex: ifcfg-eth0:2)from RHEL5, i had deleted the ifcfg-eth0:2 file from /etc/sysconfig/network-scripts/ifcfg-eth0:3but i can still see the entry in the graphical network configuration after i issued the command system-config-network, i want to remove it from there.
View 3 Replies
View Related
May 20, 2010
i installed and ran System Profiler & Benchmark ran a test. then i rebooted and turned off ACPI/PowerNow. at this point i realized my network card had gone down so i went back an turned the ACPI on. nothing changed.
View 1 Replies
View Related
Sep 5, 2010
I'm not sure what's going on, but I have two computers that both aren't working after I reboot them. When I boot up the machine and do ifconfig, eth0 is missing.If I issue $sudo ifup eth0 then the ethernet is working, but I'm not sure why I'm booting up without a connection. Even after $sudo ifup eth0The networking app that's in the taskbar is missing.looked at dmesg and it looks normal$dmesg | grep -i ethmy interfaces fileiface eth0 inet staticaddress 192.168.15.146netmask 255.255.255.0gateway 192.168.15.1
View 2 Replies
View Related
Oct 18, 2009
I've got a 64 bit home server system that was upgraded from FC2 to 7, 9, now 11. I've now got a weird situation where dns inquiries will not work when I reboot the machine, until i restart eth0. When I reboot, I can open firefox on the machine, put in the IP of my dsl router, and look at it's settings just fine. All other internet uses, whether it's yum,squid, or etc. comes back with the usual name server not found messages. I've got thenetwork setup to use the named on this server, ( the web's a tad bit slower when I set it up to use ISP's windows nameservers, go figure).
Anyway, a few years ago I set up the machine to use the network service to bring theseinterfaces up. (I believe this was because the early versions on Networkmanger had some issues. In an attempt to fix this issue I reset Networkmanger start at startup, and reset up eth0 and 1 to be controlled by it.I then got namserver1=XXX.XXX.XXX.XXX in resolve.conf at reboot..(yeah they were really X's, I'm not hiding an ip here) I tried going intonsswitch.conf, found the line hosts: files mdns4_minimal [NOTFOUND=return] dnsand changed it to:hosts:files dns mdns4_minimal [NOTFOUND=return]No joy, I still have to do an ifdown eth0 and an ifup eth0 to get dns to work..
View 3 Replies
View Related
Aug 13, 2010
I'm having the same Harker2010 's problem.Running 10.04 LTS on a Dell latitude D-820, and switching between lan and wifi worked OK until last upgrade.Harker2010's screenshots are also valid for my problem. I've tried everything I see on this post but the problem still there.
View 1 Replies
View Related
Oct 24, 2010
I'm using Easytether through my HTC Droid for interwebs running Ubuntu 10.04. However I also have a home network. However when I hardwire into the network via a D-Link router (Auto eth0) my internet no longer works. The same is true when I plug in my iPod. The Droid loses it's connection. What is the problem?
View 2 Replies
View Related
May 14, 2010
Ok, so eth0 is up and working great. eth1, however, comes up with a link light, however the packet counters in ifconfig remain at 0. Appears that eth1 isn't working.
Here's my setup:
-Dell latitude CPi laptop with 2 PCMCIA network cards and no built-in ethernet.
-Slackware v11
-eth0 is connected inside my router on my 192 network. Static address with good connectivity
-eth1 is connected on the other side of my router in promiscuous mode in order to listen to the traffic coming into my network.
Troubleshooting so far: I have switched the pcmcia cards between slots and regardless of which card is in eth0 or eth1, eth0 works and eth1 does not. I have also switched the card dongle between cards as well as the ethernet cabling between the cards. With any of the combinations eth0 works like a champ but eth1 does not, so I think I've ruled out hardware problems.
View 14 Replies
View Related
Aug 4, 2009
my eth0 suddenly stopped working on FC10. i have been using it the whole time, and now it refuses to even ping the gateway. dhclient is not receiving a dhcp offer and when i put in the information manually, it is not even able to ping the gateway. netstat -rn shows that the destination of the router is going nowhere.
i do not think it is the hardware/software, but rather maybe the provider? i am from central europe but just moved up to great britain and working at a friends place. i can connect the mac powerbook without a problem (it will get an ip with dhcp), but not the linux machine.it is a normal ethernet modem connection here. can it be, that it checks MAC addresses or even the computer names? the powerbook also has a really weired IP address: 77.102.xxxxx
i am not using network manager, but command line tools and have nm uninstalled. does anyone have a clue, what this could be about? i am not a newbie, but this is really puzzling me.....
View 4 Replies
View Related
Oct 13, 2010
I am trying to get a network bridge configured but every time I make the changes and restart networking (or reboot) eth0 appears to come up OK but I can no longer talk to the outside world via it. With no bridge defined, I can talk to the web using either wireless or wired; wicd is configured to switch to a wired connection when available (got rid of Network Manager. It didn't recognise eth0(!)).
I want to use the bridge so virtual machines (LXC containers) can talk to the web when the machine is wired to the wireless router. Eth0 gets its IP address (192.168.1.4) via DHCP from the router and I want to bridge to another subnet, 192.168.154.n say, and the containers will have fixed IP addresses 192.168.154.101, 102, 103 etc.
[Code]...
View 3 Replies
View Related
Aug 19, 2009
5.10 Breezy configured as machine controller. Works great eth0 is a fixed IP to communicate with controller comms board. Not easy at all to alter - the comms board is hard coded to listen on eth0 for commands.
I can use eth1 as the default gateway and ping google.com, etc. But when I now attempt to communicate with the controller with netcat, e.g.
Code: echo !HH | nc 192.168.1.6 80
I obviously never get an answer since the request is passed via eth1. Using the -g option with netcat doesn't work either. I had a look at iptables but it doesn't seem to be able to do what I want. How I can still use eth0 as my communication port to the controller whilst eth1 is the default gateway?
View 17 Replies
View Related
Jul 1, 2010
I have two servers on a vlan at my datacentre/colocation and previously both servers had public IPs on their eth0 interfaces. The servers are HP ProLiant DL360s - one is a G4 and one is a G5 The newer G5 is now the LAMP server and the G4 has been retired and I want to repurpose it as an iSCSI target using openfiler freenas or similar.
My G5 has public/static IPs lashed to the eth0 physical interface and the eth1 is not configured to do anything yet. The G4 will have both interfaces available - perhaps one for ssh access from one of my static public IPs and the other to be a private IP on the local vlan. Here is what I am trying to get my head around...
The G5
eth0 - Public IP - full LAMP services on two or three virtual interfaces
eth1 - Private IP 192.168.0.1
The G4
eth0 - Public IP for ssh
eth1 - Private IP 192.168.0.2
Because my traffic between eth1 on these boxes is via private IPs on the local private vlan it doesn't add to my quota for bandwidth. How do I go about configuring the routing and gateways and other aspects of this so that I can run a private IP space network between the eth1s and still serve the outside world from the eth0s...
I am afraid that if I assign the private IPs to the eth1 interfaces the routing may either not work or interfere with the access to the production internet facing interfaces (eth0s).
View 10 Replies
View Related
Dec 18, 2010
I'm running a dual boot Ubuntu 10.04/Backtrack 4 (Ubuntu 8.10) system. I can get internet in the BT4 side but not in the Lucid side. In Lucid I can ping my router, and the network manager says I'm good to go, but I can't get to any web sites. It all started when I tried to put my laptop on another network by mimicking the settings of a computer I had just unplugged from the network. MAC address and all.
ifconfig eth0:
Code:
eth0 Link encap:Ethernet HWaddr 00:1f:16:ba:4c:8c
inet addr:10.136.9.147 Bcast:10.136.9.159 Mask:255.255.255.240
inet6 addr: fe80::21f:16ff:feba:4c8c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
View 3 Replies
View Related
May 27, 2010
I recently installed Ubuntu 10.04 on an older PC and I'm having problems with the network card built into the motherboard. When I connect an ethernet cable into the ethernet port I get a solid amber light, and I can't connect to my router, (which is being directly connected). Nothing is shown in Network Connections, but on another PC with the same version of Ubuntu it shows "Auto eth0", and it works just fine connecting with the router.How do I fix this? I'm an Ubuntu noob so I'm not really sure what to do here.
The network card is an Intel 82547EI Gigabit LAN controller, and Intel's website offered a driver available for my kernel version of Linux. However I was typing everything it told me to do in terminal, (which half the time I have no clue what I'm typing actually means), but I ended up getting some errors towards the end of the install process. I'm not sure if I messed something up or the driver just isn't going to work.
I'm hoping there is an easier fix for this, I've been searching the net all night trying to find someone with a similar problem and I haven't found any. I think I have another ethernet card which I might pop in and see if that works....but I figure I'll most likely run into the same problem because I know for sure the motherboards network card works - has on Windows, I just can't get it working in Ubuntu.
View 9 Replies
View Related
Apr 22, 2011
im trying to setup eth0 with subdevice eth0.0 and eth0.99 to come up at boot
eth0 is dhcp clint
eth0:0 is static ip
eth0.99 is 802.1q vlan interface
/etc/network/interfaces
Code:
auto lo
[Code]....
View 1 Replies
View Related
Dec 26, 2010
i install kernel rpm after i boot that kernel network not working kernel name : kernel-rt-trace-2.6.24.7-132.el5.centos.i686 [URL] error "Bringing up interface eth0: Device eth0 has different MAC address than expected, ignoring."
View 1 Replies
View Related
Jul 30, 2010
I try to generate a server client code. What i try to do is sending video streams from eth0 and eth1 to the other server programs' eth0 and eth1. In order to do that, i decided to use SO_BINDTODEVICE. But the code is not working. Am i misunderstood the usage of SO_BINDTODEVICE.
1-Defining two ports
2-Defining two sockets
3-Assigning host ips on them
[code]....
View 3 Replies
View Related
Jun 3, 2010
in order to select multiple items, shift key was hold for several seconds[sure > 8sec] and there after system is not taking any input from keyboard. however only the mouse works. i searched a lot and found some remedies like hold right and/or left shift keys for 8 sec and it will revert back. press shift key 5 times and hold ins key for 8 sec etc,. but i tried all these and none of it seems to be working. i even hold some alphabet key for 8 seconds to see if it takes input, but none of them seems to be working
i connected this keyboard to other machine and it works fine. this keyboard is USB dell keyboard. i tried logging in init level 3 and even with this i can not input anything from keyboard. i did reboot several times and unable to even login as it does not take any keyboard input. the only way i can access this system is to remote login from other system and work on command prompt!!is there a fix to it? accidentally if something is changed in which file it is saved? can i edit that file and restore to normal? am not sure if all these does not work i may have to reformat!! but this is the last thing i want to do
View 1 Replies
View Related
Nov 16, 2010
i m using RHEL5 ......but only prob i m facing is that there is no sound in my system.
[root@localhost ~]# /sbin/lsmod
Module Size Used by
deflate 7873 0
zlib_deflate 21977 1 deflate
[code]....
View 4 Replies
View Related
Jul 21, 2010
I have sound problem I am using rhel5 kernal 2.6.18-8.e15
Audio model =Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
I have tried lot of thing but not getting result.
View 3 Replies
View Related
Mar 17, 2011
I have RHEL 5.5 ,Suse linex and windows7 is also running in my system. I am not able to connect to internet from Linux, but internet is working in windows 7 and suse. The service provider is qwest and they say that they do not support linux.
View 3 Replies
View Related
Jun 23, 2011
need to know, how we can display the whole (till current directory) path in below highlighted way. normally it shows only the name of current working directory after the server name.
View 3 Replies
View Related
May 11, 2010
Tata photon card is not working in rhel4 and rhel5.
View 4 Replies
View Related
Sep 27, 2010
I have a hardware device with two ethernet ports, eth0 and eth1 running Centos 5. Basically my goal is to forward packets from eth0->eth1 and eth1->eth0 as well as get a copy of these packets for analysis. If I set IP routing to do the forwarding then I won't get a copy of the packets for analysis.
View 3 Replies
View Related
Apr 22, 2010
WiFi worked PERFECT in 9.10 after
Code:
Sudo apt-get update
apt-get upgrade
But that only worked when I put in my eth0 cable to get the Updates. Now I upgraded to 10.04 LTS and it isn't working- eth0/wifi. So Now what do I do if i can't even get the updates in Terminal?
View 2 Replies
View Related
Apr 20, 2010
Some time throughout the night last night eth0 stopped working entirely, I could not resolve dns or any thing. Oddly though eth0:1 and eth0:2 worked perfectly with a ping -c 10 -I eth0:2 xxx.xxx.xxx.xxx but still could not resolve domain names. My nameservers are good as i have tested them on my other machine. My setup had been working fine for quitte some time and i did not make any changes besides updating webpages, it is a server running Debian Lenny. Unfortunatly since eth0:1 was working for the most part i was trying to change the IP's in the config and accidentally killed the settings using webmin so I cant post to many details at the moment until my host for the dedicated gets my /etc/network/interfaces restored but in the meantime i have searched all over google to try to find an answer to the original problem but cannot so i would like to prepared for when the server is accessible again.
View 2 Replies
View Related
Aug 12, 2010
I installed F13 on an Acer laptop for a friend who is just beginning with Linux. This laptop has the dreaded Broadcom chipset and is using the b43 driver. When it was first installed, wireless was automatically detected and worked fine. However, as usual, there was about 200MB of updates after the install, and the wireless was downloading extremely slowly, so I connected eth0 just to complete the updates. Ever since, the wireless will not work. When the machine is booted, wireless is shown as disabled in Network Manager. I remembered that there was a wireless switch on the front of the laptop and switching it on allows me to check the enable wireless box, but wireless says device not ready.
ifconfig wlan0 up returns:
Code:
SIOCSFFLAGS: Operation not possible due to RF-kill
I assumed this meant that the switch was in OFF position, but it is not. iwconfig shows the wireless is detected. It appears that there is a script for rf_kill somewhere in the filesystem that is keeping this from working.
View 1 Replies
View Related
Mar 8, 2010
If I uncheck and recheck "Enable Networking" in the Network Manager Applet 0.7.996 I would expect the wired network to disconnect (which it does) and reconnect (which it does NOT). So I tried sudo ifdown eth0 and got
Quote:
Ignoring unknown interface eth0=eth0.
ifconfig tells me
Quote:
eth0 Link encap:Ethernet HWaddr 00:25:64:e8:18:2c
inet addr:192.168.0.112 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::225:64ff:fee8:182c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
so I am at a loss. How do I stop and restart the network interface short of rebooting the machine?
View 9 Replies
View Related
Mar 3, 2010
I got two IP's in my dedicated server. Both are external IP's. I would like to make connections using 2nd IP address under eth0:0 interface. For example: when using "lynx whatismyip.com" should display my 2nd IP. How to do this using iptables ?
View 1 Replies
View Related
Feb 3, 2011
my company there is 1 RHEL5 server and around 50 systems connected to it( running windows ). I want to know who is pinging or telneting to the server how can I find this information on the server OR where should I look for this information in the linux.
if I want to explore on this topic (i.e. who is trying to connect to server, from where user accessing server, whats his/her ip, whats his/her os etc. ) where should I look for it on the net ??
View 4 Replies
View Related
