Networking :: Add - Wireless Configuration In Interfaces
Jun 28, 2011
Is there a way to add the wireless network which has a WPA/WPA2/certificate + Peap+MsChap+user+password to /etc/network/interfaces? Am trying to do a bash script that asks user and password and dumps it with addition info such as Peap/Mschapv2/cert into /etc/network/interfaces so it could be automatically activated. Any Ideas? Am on ubuntu 10.04 - using the GUI network-manager it connects without any problem after adding the user/pass/cert/mschapv2/peap. But I wanted to be configured thru command line?
View 1 Replies
ADVERTISEMENT
May 11, 2010
My new Squeeze machine detects all of my hardware including the LAN and WLAN cards, but only brings up the LAN card. There isn't even an entry for it in /etc/network/interfaces for me to modify. I tried adding the info manually but then the entire network wouldn't start. I had it configured as a static IP and I know the commands were correct due to them working on the LAN card. I believe that the name "wlan0" was causing the problem, but how else can I bring it up at boot?
View 7 Replies
View Related
Mar 18, 2011
For some reason, i just cannot get my wireless to work in xubuntu. When i click on the network-manager applet, it only has the wired network tab and VPN connections, there are NO wireless networks displayed. I have also tried iwconfig, which returned
lo no wireless extensions.
eth0 no wireless extensions.
and lspci:
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07)
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03)
[Code]...
View 1 Replies
View Related
Mar 24, 2011
Similar to the linux command "chattr +i filename", I would sure like to set my eth0 interface immutable. so once I assign the eth0 interface's IP and gateway, make it stay set until I say otherwise.
this way, I can run dhclient or Networkmanager on another interface without having to fret that it may alter this interface. is there something out there that can do this?
View 1 Replies
View Related
Jul 5, 2011
I've installed backtrack 3 in a vmware machine also i'm using a tp link adapter for to do it this is the model tl- wn422g 54 mbps high gain i have wifi internet i can surf the internet (inside backtrack) but the problem starts when i type in the kernel console airmon-ng nothing appears in interface channel etc then i try iw config and also nothing detects and it's frustrating because i'm connected to the internet.
View 2 Replies
View Related
Mar 2, 2010
Problem:I got a new Acer Aspire 8935G notebook, installed Ubuntu 9.10 on it and everything is fine, except the fact, that it wont detect any network interfaces (or how to call it So there are no ethernet or wlan connections available in the network-manager..
lspci gives me following lines:
joe@IGNAZ ~ $ lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev
[code]...
View 9 Replies
View Related
Jan 7, 2010
I have a weird issue that I have not seen on any forum. My jaunty on DELL studio laptop seems connected to net, but I can not access any network service (ssh, firefox etc.). But when I connect a cable the cable lights blink as it should be and in wireless connection my wifi light blinks.
It was working 2 days ago without problem, and I have not done big changes recently.I removed and reinstalled network-manager and network-manager-gnome. Nothing changed. I see a message in each restart as follows (when Openafs is starting). I can reproduce it with "/etc/init.d/openafs-client restart"
Code:
ADVISEADDR:error in specifying interfaces: no existing ip interfaces found
#lspci
Code:
04:00.0 Network controller: Intel Corporation Wireless WiFi Link 5100
08:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe (rev 10)
#lshw -c network
[code].....
View 5 Replies
View Related
Jan 25, 2010
I have 3 Interfaces for a different LAN's and when I start one interface the another interfaces goes down.How can it's possible?I configure my ethernets as:
Code:
/sbin/ifconfig eth0 172.16.3.108 netmask 255.255.0.0 broadcast 172.0.255.255
/sbin/ifconfig eth1 172.16.3.109 netmask 255.255.0.0 broadcast 172.0.255.255
/sbin/ifconfig eth2 172.16.3.1110 netmask 255.255.0.0 broadcast 172.0.255.255
View 12 Replies
View Related
Feb 17, 2010
the default for /etc/network/interfaces? I believe I screwed it it up because I can detect my wireless, it just won't allow me to connect to it. The settings in the /etc/network/interfaces are all messed up. I'm running Ubuntu 9.10.
View 2 Replies
View Related
Apr 16, 2010
If I try to add a new interface (eth1) to /etc/network/interfaces, I get
Code:
* Reconfiguring network interfaces... SIOCSIFADDR: No such device
eth1: ERROR while getting interface flags: No such device
SIOCSIFNETMASK: No such device
[Code]...
How do I add 2 interfaces and get anyone of them to work, as available ?
View 5 Replies
View Related
Aug 3, 2010
I had some trouble with the netinst CD and I had to install lenny with the 6DVDs instead. My internet connection only works after I edit the interfaces and resolv.conf files manually. So my question is: can I do that from the netinst CD before it actually needs the connection to install everything? (otherwise I'll just need to use the DVDs.
View 4 Replies
View Related
May 25, 2011
Can you "split" a network interface in Ubuntu, similar to how airmon-ng lets you use your wireless card in managed and monitor mode, by making another interface out of the same hardware? I know it'd be slower, but I'd still like to do it.
View 4 Replies
View Related
Oct 23, 2010
I have a weird problem with my /etc/network/interfaces configuration. I have the most simple static setup possible: Code: # cat /etc/network/interfaces
auto lo
iface lo inet loopback
auto eth0
[code]....
View 1 Replies
View Related
Mar 30, 2010
I had one of those random system deaths, so reinstalled squeeze (daily netinst image I think...) on my eee 1000, which uses an rt2860 wireless chip. The new install only installed 2.6.32, which I had been avoiding using because of a few problems, including it dealing with networking slightly differently. I couldn't get it to work - even without encryption - using wicd. Having had a read of [URL]... , I had a look at /etc/network/interfaces, which read; This file describes the network interfaces available on your system and how to activate them. For more information, see interfaces(5).
[code]...
ra0 is now called wlan0, as far as I'm aware. I've read in several places that it is best to expunge this file of all references to wifi, so I removed the bottom section (after '# The primary network interface'). I still got nothing. However, if I go ahead and change the 'ra0's to 'wlan0's, it seems to work - wicd connects. Not very familiar with Debian (spent more time on SUSE. Drop your tomatoes - I like it. Any idea what is happening? Is what I'm doing wrong? Conversely, is the file wrong? Should it be reported? Against which package? Including any particular files?
View 2 Replies
View Related
Jun 16, 2010
I have a netgear wg111t that is running with ndiswrapper. It has an atheros chipset, but calling it ath0 didn't work.
Heres /etc/network/interface :
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface auto lo
iface lo inet loopback
View 6 Replies
View Related
Aug 8, 2015
I have a laptop connected to internet via wlan0. I also have eth0 interface and with it I share internet. I want to modify/filter all the traffic passing by the first laptop, something like this:
Code: Select all          *---------------------------*
          |    LAPTOP 1      |   *--------------* ?
          |-----*  *------*  *----*   |       |
  INTERNET<------>|wlan0|<-->|MY_APP|<-->|eth0|<---->|ANOTHER LAPTOP|
          |-----*  *------*  *----|   |       |
          *---------------------------*   *--------------*
I know that in FreeBSD it is possible to use ipfw for that purpose, because it build-in into kernel. We set for example rule Code: Select allipfw add divert 2000 ip from any to 1.0.1.1
and we can use our own application to process those packets, reinject them forward etc. It will work also fast, because as I said, it build into kernel.
Is there any standart Linux-based solution to do the same? I found some info about netmap-ipfw. Is this a correct solution? Or I have to use for example IP-aliases and iptables to do that?
I need to process all the IP-packets, not only TCP/UDP/etc-protocol. Solution also must be very fast.
View 0 Replies
View Related
Mar 29, 2010
I have a rather urgent problem with my network, I got two virtual network interfaces one internal and one external. The problem is; I can't get connection to internet. The external NIC is set as a NAT and the internal is... internal.
/etc/network/interfaces
auto eth1
iface eth1 inet static
address 192.168.1.200
netmask 255.255.255.0
Running with this configuration makes my internet connect go away, however if I remove the configuration for eth1 everything is working fine.
View 3 Replies
View Related
Jan 10, 2011
I was just wondering if there's any point having both auto and allow-hotplug against the same interface in network/interfaces as allow-hotplug seems to bring an interface up at boot on its own.
View 3 Replies
View Related
Jun 27, 2011
I have a Dell PowerEdge SC430, Squeeze 6.0.2 box, Broadcom NetXtreme NIC which works fine DHCP. The network-manager package is not installed. I have now reconfigured /etc/network/interfaces for a static IP:
auto eth0
iface eth0 inet static
address 192.168.1.2
[code]....
View 7 Replies
View Related
Feb 11, 2010
What is the maximum number of virtual network interfaces possible?I would like to create around 300 or so. This is needed to simulate a 300 node network.
View 6 Replies
View Related
Dec 20, 2010
Alright, every time I boot or shutdown my routing box, it hangs at configuring and deconfiguring network interfaces. Below is my interfaces file. I see no errors or warnings in my log and I am running a pure kernel, not tainted with proprietary drivers. All of my hardware is 100% supported.
[code]...
View 14 Replies
View Related
Jan 6, 2016
As above, my wheezy 32bit hangs at boot. the last few lines displayed are
Code: Select allMounting local filesystems...done.
Activating swapfile swap...done.
Cleaning up temporary files...
Setting kernel variables ...done.
Setting up resolvconf...done.
Configuring network interfaces...
[Code] ....
I removed the files from /etc/network/interfaces.d/ just in case. i still can't boot up.
Resolved (I think) as on this post: [URL] ....
View 14 Replies
View Related
Dec 23, 2009
I am trying to write a program to list wireless interfaces and changing mac address the interface that will run primarily on ubuntu 8.04 and hopefully other linux distros.I am able to list out the wireless interfaces and change MAC address using popen with linux commands in ubuntu 8.04Is there a way to use C++ to do the above instead of using popen with linux commands so that the program can be used for other linux distros?I have been googling on this but no luck so far.
View 2 Replies
View Related
Dec 9, 2010
My C++ program must be able to detect EVERY Wireless Network Interfaces under Linux operating system and display the interface names on the screen.How can my application achieve this?Is there any sample codes?Is there any third party libraries can do this?Notes: The detected wireless network interfaces should also include the virtual interfaces, like the one created by Aircrack-NG's Airmon-NG script.
View 1 Replies
View Related
Aug 14, 2011
i recently started sockets programming. In the process i began to look for relevant network information about my computer and realized that ifconfig wasn't displaying the same information that resides in my /etc/network/interfaces file. On the interfaces file my IP address is 192.168.1.109 for interface eth0 but ifconfig displays 192.168.1.101. I was under the impression that ifconfig got its information from the interfaces file but clearly doesn't. I tried re configuring the device with ifconfig and then disabling and re enabling the device with ifdown and ifup so that the device updated its information but it didn't.
[Code]....
View 3 Replies
View Related
Nov 20, 2010
I'm building a wireless router based on OpenSuse 11.3 I have experience with Debian, but here I'm confused howto manually configure network interfaces. I need my wireless card to work in master mode, so I need to place
[Code]...
View 3 Replies
View Related
Apr 24, 2009
I have recently installed CentOS 5.3 in my system. I needed some help with the wireless configuration. Actually i have configured it and it shows the wireless name but it doesnt connect to it. in solving the issue.In the /var/log/messages , the following error appears :
Apr 24 20:46:51 localhost NetworkManager: <info> Activation (wlan0) starting connection 'OMWLAM'
Apr 24 20:46:51 localhost NetworkManager: <info> (wlan0): device state change: 3 -> 4
[code]....
View 1 Replies
View Related
Jul 12, 2011
Having difficulties configuring a driver for an Edimax wireless usb [URL]... I have downloaded the driver, and after make clean I am running into problems.When I enter make I get the following.
Code:
make ARCH=i386 CROSS_COMPILE= -C /lib/modules/2.6.32-5-686/build M=/home/conor/rtl8192CU_linux_v2.0.939.20100726 modules
make: *** /lib/modules/2.6.32-5-686/build: No such file or directory. Stop.
make: *** [modules] Error 2
This worked ok on my Ubuntu 10.04 install on my desktop but it does not seems to be working on my Crunchbang 10 latest release on my laptop.
View 4 Replies
View Related
Dec 4, 2010
I have 2 users on my HPmini 210 netbook running Squeeze. I just found out that it does not connect to existing wireless networks when I login as the second user. Is it supposed to happen by default or am I supposed to do something to make that happen? Another problem is that when I tried to create "new connections" again for the second user, the keys won't work. The same keys are working for the first user. The network keys are WEP 64 bit HEX.
View 2 Replies
View Related
Feb 7, 2011
I installed Debian 6.0 on my hp dv400 laptop, Ive been using linux ubuntu for a while now and my wireless card has always been picked up but after isntalling Debian its not working. This is what I have. Also I cant seem to install awn for some reason.
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 04)
00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 04)
00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 04)
00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 04)
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 04)
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 04)
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 04)
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 04)
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 04)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4)
00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 04)
00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 04)
00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 04)
00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 04)
00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 04)
06:05.0 Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05)
06:06.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus Controller
06:06.2 FireWire (IEEE 1394): Texas Instruments OHCI Compliant IEEE 1394 Host Controller
06:06.3 Mass storage controller: Texas Instruments PCIxx21 Integrated FlashMedia Controller
06:06.4 SD Host controller: Texas Instruments PCI6411/6421/6611/6621/7411/7421/7611/7621 Secure Digital Controller
06:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
View 3 Replies
View Related