I'm using BackTrack 4-R2 and after trying for about 3 days now, I decided to do a fresh install and start from scratch. All of the "HowTo's I saw were for Ubuntu and didn't work.
View 1 RepliesMy laptop is configured to boot openSUSE 11.1, Vista, and Win2k. Access Point is AirLink101 (Atheros Based).Laptop is Acer Aspire 9410-2028.Win2k wireless speed is 108 (using Atheros Drivers)Vista Wireless speed is 54 (using windows drivers)openSUSE 11.1 Wireless speed is 12 (Using MadWiFi)When I was on 10.3 it ran at 108 on 11.0 it was 36. 36 is not 108 but it was solid 36. I tried using networkmanager and speed went down to 1. Each new version of openSUSE has caused a drop in wireless speed.lspci |grep Atheros0a:05.0 Ethernet controller: Atheros Communications Inc. Atheros AR5001X+ Wireless Network Adapter (rev 01)
View 2 Replies View RelatedI have thi errors when i try to install madwifi:
View 3 Replies View RelatedI have successfully created an access point on my Laptop via Madwifi drivers. A second laptop can successfully associate with the created AP. But ping is not possible from both sides.
AP on the first Laptop:
ifconfig ath0 10.0.0.1 netmask 255.255.255.0 broadcast 10.0.0.255 up
Second Laptop:
ifconfig ath1 10.0.0.50 netmask 255.255.255.0 up
route add default gw 10.0.0.1
Association works, but ping command is not possible from both sides:
ping 10.0.0.50
ping 10.0.0.1
What could be the problem?
I'm trying to install a Netgear WG311T V1H1, rev A3, Atheros AR2414 mac 0x79m phy0x45 on Centos 2.6.18-128.el5. Two methods are offered. The distribution comes with Madwifi's latest driver, ath5K, but it is not supported for this card and is unstable. It will connect but has variable data rates and will drop out with long downloads. My research indicates that the madwifi 0.9.4 driver should support this card. Both methods call for blacklisting ath5k, which I did.
1. Following Centos directions, [URL], I installed the configured RPM Forge and did yum install madwifi, which was successful. The command modprobe ath_pci produces the error "module ath_pci not found." It appears that the RPMForge download did not install these needed bits. So my fundamental question is where is the ath_pci? It is not on the machine.
2. Following the Madwifi directions, I did yum install gcc make perl, which was successful. Their next step, the 'make' command, yielded the KERNELPATH error described on their page [URL]. It points to /lib/modules/2.6.18-128.el5/build, but 'build' is a path, not a file or directory. Installing kernel-devel to get the build files on the system was suggested by another web page, and I did it with yum install kernel-devel, and it was successful, but did not change the error. The literature says I can redirect the make command to the correct spot, but there does not seem to be a correct spot.
does it still support the madwifi driver. i have tried to compile madwifi 0.94 that i got from svn and from sourceforge and it was succes, but the problem is it doesnt work. when i compile the source from subversion, i get the ath0 on iwconfig command but i can't get any wireless network on list of network. if i use the one from sourceforge, the iwconfig list even doesnt contain any ath*
View 3 Replies View RelatedI have Atheros AR5008X mini PCI express card in my DELL Studio 1535 laptop..am running Ubuntu 8.10..
I blacklisted ath9k driver and compiled n installed madwifi from the svn trunk...
I am getting this error often in
Code:
/var/log/syslog
wifi0: ath_fatal_tasklet: Hardware error; resetting.
Anyone got idea about above error? My wireless internet connection works fine amidst the above error..
When i try to put my card in monitor mode with below steps:
Code:
$sudo ifconfig ath0 down
$sudo wlanconfig ath0 destroy
$sudo wlanconfig ath0 create wlandev wifi0 wlanmode monitor
[Code]....
I have a bit of a silly question, as I should know better, but I have a Toshiba A200 laptop that wasn't working well with the default ath5k driver so I switched to madwifi. It works great, but after the laptop goes into suspend or reboots, the driver doesn't get loaded and wireless isn't available.
I've been working around this by going to proprietary drivers, which shows the madwifi driver. When I say activate, it comes back with a failed message but works.
I'd like to save myself from going through this several times a day, but I'm not 100% sure what to do. Do I add madwifi to modprobe or something like that?
I am among those unfortunate wretches with an Atheros wireless card (ar5001) and I've had problems with it from the day I installed Ubuntu. I've been using Madwifi to connect to the internet, and it's worked fine, until I lately changed my internet connection, got a new modem etc.
Madwifi works still, but the signal is really weak - while not so on Windows Vista.
I know it's NOT ipv6 related. Do I have to change the connection settings? Is my card outdated or whatever? Am I using inefficient drivers? Should I just not use Madwifi and rather something else instead?
(Trying to install ndiswrapper and get it to work was a dreadful process, so I won't attempt that again.)
I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System -> Administration -> Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong?
Some information about my system:
iwconfig
Code:
lo no wireless extensions.
eth0 no wireless extensions.
wifi0 no wireless extensions.
ath0 IEEE 802.11g ESSID:""
Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated
[Code].....
I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck
i try to install my d-link dwl-g520 h/w:A1 in master mode with madwifi drivers but:
$ lshw
*-network:1
description: Wireless interface
product: Atheros AR5001X+ Wireless Network Adapter
vendor: Atheros Communications Inc.
physical id: 5
bus info: pci@0000:00:05.0
[Code]...
I'm in the process of installing Slackware 13.1 on my old IBM A22m laptop.Since version 12, I've used WPA_supplicant and the Madwifi drive to set up my wireless connection (using a PCMCIA D-Link card). It has worked great all along, up through Slackware 13.However, I've noticed that Alien Bob's Madwifi instructions and repository do not have builds or packages for Madwifi beyond Slackware 12.2.
I think I simply built the drive in 13 by modifying the slackbuild for 12.2.Anyway, what's the latest/best way to set up wireless with an Atheros chipset? Are there Madwifi packages available for Slackware 13.1?
I know this has been asked in a previous post:[URL]...BUT, i am not using the package assistance module that was used in this case. Im running Backtrack 4 R2, with a PCMCIA Netgear WPN511 card on a 16gig USB flash drive (dell inspiron 2200, 256MB pc333 RAM, 70 gig HD - i know this sounds minimal but it is running great, and will stay minimalist). The current kernel version is 2.6.35.8.
I am having problems with any version of madwifi i download/guide i follow. And, because madwifi.org is down (as usual), im having a hard time finding current sources. I am aware that there is the atheros 9000 driver, but am clueless as to install that as well, and from what i've read, madwifi suits my needs better. Once again, i am new, so if this is also incorrect, i'd love to know why! Im rather unfamiliar with how kernels/headers interact with drivers, so feel free to low-ball replies.
I've opensuse 11.2 installed. Why here: Additional package repositories - openSUSE. I cannot find MadWifi Repository for 11.2?
View 7 Replies View RelatedI've just picked up another Orinoco Proxim Gold WiFi card for a laptop (this one) that I've put Debian on. I have another Dell laptop that I put Debian on a few years ago and have the same card for that one too. I installed the drivers on the other one (ages ago so I don't remember how exactly I went about it) but when I try to install the same drivers for the same card on this laptop I keep getting these errors:
[code]...
why it worked on my other Dell a couple years ago but isn't working now.
I have installed the madwifi drivers and I am able to put the wireless device into monitor mode using airmon, so that tells me that the driver is working and the device can be picked up...
But I still can't connect using Wicd and I really don't know what to do next
Basically what is happening is i installed slackware 13 and then madwifi following these instructions [URL] and it works great, then i shutdown or restart and when i come back to linux i dont have the internet anymore. This happened twice already and i dont know how to fix it. by the way i have 2 hard drives, one with windows xp and one with linux. i dont think this would affect anything but i put it just in case.
i will try to install it again from scratch following those instructions exactly because i just went to the configure and make part, i will take the post down if it works after that but if this is up then it didnt work. i know i didnt provide any info on things like the output of iwconfig or the model of my network card (atheros something) but all i can say right now is that i use the latest version of madwifi, 0.9.4, the fixed one that works for the latest models of atheros.
I installed newly Ubuntu 10.04 LTS on Acer Aspire One notebook. When I issued the command 'sudo apt-get install madwifi-tools' it returns 'Couldn't find package madwifi-tools'
In software sources, all the options main, universe, restricted, multiverse are checked.
I am trying to get the madwifi driver installed on my new ubuntu 11.04 system. I am getting the following error: ./kernelversion.c:13:30: fatal error: linux/utsrelease.h: No such file or directory compilation terminated. Makefile.inc:81: *** Cannot detect kernel version - please check compiler and KERNELPATH. Stop. What is the value of KERNELPATH? I have the following content in /usr/src.
[Code]....
I am trying to install Madwifi 0.9.4 on my Centos5.5 and have absolutely no idea what to do, obviously its nothing like windows which is all I have ever used until just today when I installed Centos (so yes very new newbie). So my question is, how do I install it, what do I do? I have tried looking around on the net but most posts/tutorials assume some knowledge already.
View 12 Replies View RelatedI'm trying to manually connect my wireless adapter to my router using WPA. I'm using Madwifi drivers for my D-Link DWL-G630. I keep getting the same error " Association request to the driver failed". I can connect to my router using wep through the GUI. I can not connect using the terminal. I created my /etc/wpa_supplicant.conf file
ap_scan=1
ctrl_interface=/var/run/wpa_supplicant
network={
ssid="NYNET"
scan_ssid=0
[code]....
I run these two commands
sudo ifconfig wlan3 down
sudo dhclient -r wlan3
the I run
sudo wpa_supplicant -Dwext -iwlan3 -c/etc/wpa_supplicant.conf -dd
jmorales@jmorales-laptop:~$ sudo ifconfig wlan3 up
jmorales@jmorales-laptop:~$ sudo dhclient -r wlan3
Internet Systems Consortium DHCP Client V3.1.2
[code].....
When I go to try to install madwifi in the terminal I get the following error message after typing the make command.
Checking requirements... ok.
Checking kernel configuration... ok.
make -C /lib/modules/2.6.26.8.tex3/build SUBDIRS=/usr/src/madwifi-0.9.4-9pclos2007 modules
make[1]: Entering directory `/usr/src/linux-2.6.26.8.tex3'
Building modules, stage 2.
MODPOST 14 modules
make[1]: Leaving directory `/usr/src/linux-2.6.26.8.tex3'
make -C ./tools all || exit 1
make: *** ./tools: No such file or directory. Stop.
make: *** [tools] Error 1
I am running pclos 2009.
I'm using LiveCD to test my laptop with FC 14. It booted from the LiveCD image last night, but my wireless didn't work. I need the madwifi wireless drivers for my built in Atheros adapter.
Can I download the latest and greatest madwifi drivers, compile them and use them while running from the LiveCD image?
I am trying to install atheros AR5007EG on my toshiba laptop -i figured out that best way to install this wireless card is through madwifi -while configuring madwifi i get this error
I am posting the output of different commands so you can understand better -i manually tried to link the build directories to kernel-source which failed - i am not sure exactly what kernel source is and how i can link to kernel source -
My output:
I am trying to install madwifi on fedora 12. I am getting following error which i "make" the project.
[code]...
fedora finally supported the atheros card, but well it hasnt for me. Im trying to install madwifi, but everytime I try to use the "make" command. I get this error.
[code]...
When originally installing 11.04 I had problems getting my Ralink 5390 wireless card to work.
Today my computer froze completely and I had to turn it off via the power switch. When I turned it back on, wireless was no longer recognized! My iPod can connect to the network just fine, so it must be an Ubuntu problem. There are no problems with my ethernet connection either.
I researched this and found several threads about blocking and unblocking wireless devices using the rfkill command. Well, unfortunately for me the rfkill command doesn't work. When I type sudo rfkill list or sudo rfkill unblock all, nothing happens; it just returns me to my bash prompt. I even tried uninstalling and reinstalling rfkill...nothing.
I have a strange problem for internet. My clients (winxp - S2) can't get internet.Let me explain my scenerios. Fedora 10 with lan (eth0) having direct internet from dsl model, client (XP service pack 2) can use samba shares using dhcp (wlan0) installed in Fedora 10 box. client can ping my linux box.Now problem is: client (dosbox) can ping the google ip address (i.e ping 74.125.39.106) but can't use 'ping www.google.com'. That means ping with ip works for internet from my client. My linux box can. I can use internet from FC10 but can't use iexplorer from my client to have internet. I have enable ipmasquarding in Firewall and dhcpd is running on wlan0 for dynamic ip address of my clients.Can someone suggest me what kind of problem having I? What should i do to success iexplorer for internet? what possibly am i missing?
View 3 Replies View RelatedI have been looking around the forums searching for similar problems, it seems not only me had this problem. About a month ago I did a regular update via Upd Manager. The next day - no wired connection.Still managable, since the local library has wireless. Now that won't work either.Just after I upgraded from Jaunty, I accidentally removed NetwMngr from the top right corner of the screen, but that should not have anything to do with how the program works, right? I now cannot reach NM, if I run it from the terminal, nothing happens visibly.
View 5 Replies View RelatedI have a Dell Latitude D530 Laptop (500 GB HDD). Installed Windows XP and then Ubuntu 10.10 to do dual boot. everything works fine in Windows XP.In Ubuntu 10.10 I had issues connecting to Internet(Through Wirelss), I was able to rectify this issue by dsiable ipv6 from firefox about:config and setting true to network.dns.disableIPv6. After this I was able to connect to internet and browse websites from Firefox.But I am having Issues with Evolution Mail(Connection Timed Out) and Google Talk Client(Connection Timed Out).Empathy Internet Messaging gets connected fine.I was wondering if I will have to disable IPv6 System wide and hence I added the following lines to /etc/sysctl.conf
#disable ipv6
net.ipv6.conf.all.disable_ipv6 = 1
net.ipv6.conf.default.disable_ipv6 = 1
[code]....