i would like to establish a VPN connection which can hold either 'two' hosts..and secondly if that's done i would like to go for more number of users..Can i do it using IPSec services??if yes then how?
View 9 RepliesI'm trying to perform a VPN lan to lan IPSEC connection. By my side, I have a server with 2 IP's, i.j.k.l (destined to act as a VPN gateway) and i.j.k.m (the server). I am a newbie. I don't know if this configuration is normal, but it's forced by our partner.
My configuration is:
OS: Fedora release 7 (Moonshine)
OpenSWAN version: Linux Openswan U2.4.7/K2.6.23.17-88.fc7 (netkey)
ipsec.conf
# /etc/ipsec.conf - Openswan IPsec configuration file
#
# Manual: ipsec.conf.5
[Code]...
I am getting this error when I try to bring up IPSec Tunnel.Starting connection with command /usr/sbin/ipsec auto --up 'paycode-to-vivacom' ..
104 "paycode-to-vivacom" #7: STATE_MAIN_I1: initiate
003 "paycode-to-vivacom" #7: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] method set to=106
003 "paycode-to-vivacom" #7: ignoring Vendor ID payload [FRAGMENTATION c0000000]
[code]....
I have an IPsec VPN between 2 Ubuntu 10.04.1 Boxes which is working perfectly. However I cannot get any traffic to route down the VPN link.Interestingly, when checking the routing table, there isn't even a route list for the remote network. This is the same on both sides. Also there isn't an ipsec0 interface listed either.However, when a the command "sudo service ipsec status" is ran, it definately shows the tunnel is up and connected.
View 1 Replies View RelatedI install openswan on rhel6 and when i execute the command "service ipsec start "
it say:
/usr/libexec/ipsec/addconn Non-fips mode set in /proc/sys/crypto/fips_enabled
/usr/libexec/ipsec/addconn Non-fips mode set in /proc/sys/crypto/fips_enabled
ipsec_setup: Openswan IPsec apparently already active, start aborted
[Code].....
I've been using IPv6 on my local network and through a Hurricane Electric IPv6 tunnel. I've heard that one of the built in features of IPv6 is encryption, both scrambling the data and authenticating where the traffic came from. I've done some searching and heard of SWAN and Racoon, but some of the stuff I found is old and I would like to know what the easiest/best way to set up IPSEC for IPv6 is.
View 3 Replies View RelatedI had configured IPSEC/L2Tp on my Centos 5.4 gateway machine .For testing i had disabled firewall and Ipsec is working fine.I am able to connect from client etc...Now i want to allow Ipsec and l2tp throught Firewall.here is my Current Working Firewall.Only Openvpn is allowed and is Redirected.
eth0=XXXSTATICIPXXX
eth1=192.168.1.81
OpenVpn IP Range = 172.24.0.16/4
Ipsec Ip Range = 192.168.1.0/24
[Code].....
While I successfully configured an IPsec-VPN (I use a similar tho modified setup like this:[URL].. I am now stuck on the next steps. While I can connect to everything I want, I need to configure "access-groups" and/or "users".
The scenario is similar to this: Lets say Host A, B and C allow SSH-Connections and some weird non-standard UDP-Connection from Host-VPN, and are also accessible on other ports with public IP's (like http).
I now want to limit, that an admin-user has access to all of them, while trainee-admin only can access everything on Host B and C, and CEO only can connect via telnet to Host C - and all users can be roadwarriors
(I made this example up to give you an idea what i'm trying to do - hope it makes sense). Now my question is, if someone can point me towards a direction, as I'm quite clueless at the current moment as to what to try. I know that commercial IPsec-Implementations can do this, but can OpenSWAN/... give me something similar?
I have a Ubuntu 10.10 box which i've developed an IPTables Firewall script and is forwarding my ports correctly. This service also runs Openswan VPN Server with 2 VPN's, which is also working well.
I have come across a small snag with excluding the multiple VPN subnets I have from the NAT on this box.
I have the line in my configuration file:
-A POSTROUTING -o eth1 -s 10.172.1.0/24 -d ! 192.168.5.0/24 -j MASQUERADE
Which when added to IPTables does make the VPN come to life. But I can't seem to get it to add the second subnet. Unfortunately, I can't do a blanket exclusion such as 192.168.0.0/16 because the second VPN is on a Class B subnet address which I cannot change.
Connecting two networks with ipsec on this manual [URL] The two networks are connected, everything works, the question is as follows: For a gateway to multiple subnets, I have access to only one subnet is listed in / etc/sysconfig/network-scripts/ifcfg-ipsec0 DSTNET = 192.168.2.0/24. How do I get access to all the subnets?
View 2 Replies View RelatedIs there any possibility to transport one or two VLANs through a VPN (IPSEC) link on Linux
View 2 Replies View Relatedi need to build an ipsec vpn between a linux debian server and a zyxel prestige, The debian server got 2 ethernets connection one for the internal network and the other one is public with a public ip adress.I need to know what i need for the build the tunnel, could you please let me know what i need? Let me explain i have only to configure openswan or i have to configure the iptables or somethings else too? I found this one do you think this would be work for me? [URL]..Is debian a right distro or should i try someone else?
View 2 Replies View RelatedI've no experience with IPSec. I've used many times OpenVPN (with static key or certificates x509).
Could anyone suggest me a good tutorial in order to learn IPSec vpn with Linux?
I've searched through google, and all I can find are instructions on how to set up a L2TP/IPSec VPN that works with macs and iPhones. I'm NOT trying to set up an L2TP/IPSec VPN. I'm trying to set up a pure-ipsec vpn.
The iPhone IPSec client is a built-in cisco client, I believe. I'm staying away from L2TP and PPTP because I need multicast packets to go through. *edit: wow, i just noticed that the title says "8.10 LTS". Oops! I obviously mean "8.04 LTS". Gah, the lack of sleep got to me.
I just got vpnc setup to work with my VPN at work and now I am trying to figure out how to limit the traffic that is routed through the VPN while I'm connected to it. I only want traffic going to the local domain to be routed through the VPN.This is what my vpnc config file looks like:
Code:
IPSec gateway publicdomain.example.com
IPSec ID XXXX
[code]....
My client is on Ubuntu Lucid 10.04, I installed ipsec-tools and racoon from the repositories. The gateway is installed on a CentOS machine. I've configured everything to get a working roadwarrior configuration with authentication_method hybrid_rsa client and server. It's working in aggressive mode, but in main mode I can't get it working. I delivered new CA and certificates several times but I'm still stuck.
It seems that it comes from my client not supporting the certificate sent by the server. The client contains a copy of the CA, whereas server has a private key and a certificate signed by the CA.
[Code]...
On my CentOS 5.4 box I run dns, ssh, and smtp servers. This box also has to be able to resolve and browse websites. So basically it needs iptable rules for
TCP 22 25 80 443
UDP 53
My question is, which of these services work nicely with connection tracking? I'm a little confused about how connection tracking works. For example say this iptables rule for smtp
Code:
iptables -A INPUT -s 0/0 --sport 513:65535 -d $myip --dport 25 -j ACCEPT
versus
Code:
iptables -A INPUT -s 0/0 --sport 513:65535 -d $myip --dport 25 -m state --state NEW,ESTABLISHED -j ACCEPT
So with connection tracking what exactly does it do that my first iptables rule does not do?
Also for centos is that port range correct? 2.6 Linux kernel randomly chooses a port 513-65535 when it connects to an external smtp server or say browses a site.
So I want to get mount/umount option under right click services menu. I went to Dolphin -> Settings -> Configure Dolphin -> Services -> Download New Services and from there I installed KDE CDEmu Emulator and MountISO. But neither of them is showing up in actual context menu. Neither in Dolphin -> Settings -> Configure Dolphin -> Services for that matter. I tried to install them as normal user and as a root. I went to have a peak in /usr/share/kde4/services/ServiceMenus/ but they aren't there as well... It's just me or lots of things seems to be not quite working in 11.3?
View 9 Replies View RelatedHow can Vsftpd services & Xinetd.d services can be differentiated?
View 5 Replies View Relatedi am using red hat5 n i want to create X.509 certificates for ipsec vpn help me in creating certificates, not able 2 create certificates guide me ehere is the location for certificates.
View 1 Replies View RelatedI can see this phenomenon on 2 different systems running 11.3 .In simple mode and also in expert mode.
View 9 Replies View Relatedi am working with fedora 9 i need to turn on services such as telnet,ftp,dns,nfs,dhcp etc. but the problem is i dont even find xinetd based service when i am giving this command
Code:
#chkconfig --list|more
nd some command is not working for me as well like
[code]....
I'm running xubuntu on two identical machines and both need to have file sharing working. the first installed no problem and works perfectly but the second machine will not work.
On the second machine i installed it with the install button when you click of shared folders. after it installed i rebooted and it asked me to install again. I tried to install again but it just kept coming up with the install windows afterwards. I tried purging samba and reinstalling and it did not work as well.
Im kind of lost on what to do now?
I have a RedHat linux server box connected to LinkSys router through ethernet port. I've assigned a static IP to the Linux box, which is out of range with router's DHCP range.
The Linux box has Apache, JBOSS, SVN and several other services installed, but none of these services are accessible through the WLAN. However, SSH and SFTP are accessible from WLAN.
Another interesting observation is that if I open a browser on the linux box (by exporting the DISPLAY to Exceed on my laptop on the WLAN) and point the browser's address bar to localhost:80 or localhost:9080, then I can access these services!!.. So, I suspect that something is wrong with accessing these services from a client on WLAN and I am looking for a solution for the same.
I'd like to have an easy way to configure firewall, e.g. eable/disable what mythtv needs, or enable/disable what mediatomb needs. Basically open/close a few tcp and/or udp ports for all interfaces (I have two), or just one of them.
Is there a way to add my own trusted services for the firewall?
Other recommended ways to do that? Or just write a simple shell script?
Xubuntu 9.10 on a DELL Inspiron 1150.I have a problem with intermittent dropping of my wireless connection ( see Belkin 7010 thread).Once dropped, the wireless will NOT reconnect (It just sits there saying "connecting" but never does) Same happens if I manually disconnect - I can never re-connect. On rebooting it will reconnect fine & all is well for sometimes 4 hrs.How can I kill all wireless services & restart them without having to reboot the laptop?
View 3 Replies View RelatedI installed Ubuntu 10.10 today Netbook Edition on the Asus Eee PC 1015PED. Specifications for Asus Eee PC 1015PED: Atom 455, 1.66 GHz, 1Gb ram, 250Gb drive, Bluetooth 3.0, 0.3 megapixel webcam, Gigabit Ethernet, WSVGA (1024x600), sound card compatible with the HD audio connector, d-dub, three USB 2.0 ports, 6-cell - lithium Ion - 4400mAh, WiFi 802.11 b/g/n.
solve the problem or an indication of the package to install. tutorial under the title, which services to disable to boost performance. first place to help you connect to the Internet. especially to the netbook'a - Asus Eee PC 1015PED. I updated everything on connection via cable. Detects the connection, but when it connects after a while.. "Wireless - Network Disconnected".
[Code]...
I am sharing some folders from my Ubuntu machine, using Netatalk and Avahi, over my network.I access these folders from my Mac using the AFP protocol.When all is well, my Ubuntu folders show up in Finder on the Mac and I can connect to them.But at random intervals, the Ubuntu folders will disappear. Sometimes they reappear a short while later.At other times, they wont appear until I go to my Ubuntu machine, and re-save (even if i don't change anything) the file:/etc/avahi/services/afpd.service.
View 3 Replies View RelatedI have two problem with my wireless card:
- When I connect myself to a wireless network I must give the dhclient command, to obtain a local ip address
- The system say me that haven't a bluetooth adapter, and so I can't use bluetooh services (I've try by graphical interface and by console)
These problems began when I've passed to ubuntu 10.04!
My Wireless card is: Intel Corporation Wireless WiFi Link 5100
Xubuntu 9.10 Shared folders keeps warning that shared services samba of nfs not installed although ive d/l them and installed them when i hit install again it just keeps looping back to the warning
View 1 Replies View Related