get my VIA chrome 9 video card running with my Beamerproperly installed the openchrome driver and edited the /etx/X11/xorg.conf but the resolution settings are ignored. Something seems to be wrong with my hsync settings:
Code:
$ cat /var/log/Xorg.0.log | grep -i "CHROME"
(--) PCI:*(0:1:0:0) 1106:3371:1458:d000 VIA Technologies, Inc. CN896/VN896/P4M900 [Chrome 9
[code]....
While trying to implement some of the suggestions in the fedora 12 common problems (Intel Graphics)I discovered I cannot get the resolution correct using a xorg.conf file . Here is the file# Xorg configuration created by system-config-display
Section "ServerLayout"
Identifier "single head configuration"
Screen 0 "Screen0" 0 0
[code]....
i have a Fedroa12 installed as a VM, and my problem is that i can't change the resolution higher than 800x600 .
i am trying to do that with an Xorg.conf file. here is what i did:
1. telinit 3
2. Xorg -configure (root user)
3. cp /root/xorg.conf.new /etc/X11/xorg.conf
4. inside xorg.conf i have added the following:
under the "screen" section i have added:
DefaultDepth 24 then under the "SubSection" of Depth 24, i have added:
Modes "1680x1050" "1028X768" "800x600"
but then whenever i am try to start the X, it fails with the following message: no screen found...
since i am doing it for studying only, how to configure properly the xorg.conf file ?
FC12-x86_64/KDE How can I lock in the 1024x768 resolution in xorg.conf ?
The Option PreferredMode is Ignored , checking in Xorg-0-log.
If I put in Modes "1024x768" it gets changed everytime I reboot.
I'm using the Nvidia driver. Can't use the nouveau driver, the mouse disappears when waking the computer up after about a half hour of sleep, then I have to restart computer to get mouse to reappear.
I run fedora on a server only from command line. I need to change the resolution.
I tried to create a basic xorg.con file with Xorg -configure. But Xorg command does not exist. Which rpm do I need to install?
I've created the file from new in /usr/share/X11 and then added to lines from GTF. I@ve restarted Xorg by killing the PID then restarting and I don't get this resolution unfortunately
[Code]...
monitor is a Optiquest Q19wb. I normally have is set on 1280x1024, but fedora will only go to 800x600. It has detected the monitor correctly. Not sure if being connected to KVM will cause issues. The xorg.conf does not exist. Have installed system-config-display but have not run yet.
View 1 Replies View RelatedI'm trying to get my screen resolution set in Mythbuntu 9.10, but there is no xorg.conf on my system! I'm trying to figure out what to do (the xfce tool on mythbuntu doesn't offer the correct resolution, and I'm not even sure what driver I'm using). I've seen other threads saying to run nvidia-setup or somesuch. I assume the appropriate tool in my case would be aticonfig (I saw that elsewhere too) as I'm using an ATI Radeon 9600XT, but that tool says:
Code:
aticonfig: No supported adapters detected
I need to find notes on how to achieve higher screen resolution via Xorg.conf and some other fixes since I just installed the NVIDIA driver... seems out of the box, my resolution is horrid, though theres an added NVIDIA Server and my dual monitors aren't configured to work. I used this tutorial to get the driver installed.
View 9 Replies View RelatedI am trying to run using WINE. It has a platinum rating on the site, and runs perfectly on my laptop.on my desktop it doesn't seem to run at all.The screen goes black,then brings me back to the desktop. I manually ran the WINE command in the terminal, and it produced the error "err11settings:X11DRV_ChangeDisplaySettingsE x No matching mode found 320x200x8 @0! (XRandR)". The laptop and desktop are both running the same version of WINE (1.3.3) and have similar Nvidia cards (laptop has a mobile 9600, desktop has a 9800). I found a bug report on this exact issue on the WINE website (I'll paste a link), and they mention that the solution is simply to add the 320x200x8 resolution mode to Xorg.conf.
I've tried generating the line that I may need with a web-based modeline calculator, referenced on another thread, but it caused my system to fail booting. Luckily, I backed up xorg.conf before making changes and restored the old one via recovery mode. Here's the link to the calculator, I may just be using it wrong: [URL]
I installed debian 5 in a pc with a Intel 4 series VGA. The optimal resolution for the monitor is 1360x76, but the system does not allow that. I tried to change my xorg.conf, but got no success.In my xorg.conf I used this:
Section "Screen"
Identifier "Default Screen"
Monitor "Configured Monitor"
[code]....
Since the display of my notebook doesn't work very well anymore, straight vertical blue line on the right side of the screen, I want to connect an external monitor. (ADI [it doesn't say the exact model] 21 inch; resolution 1600x1200 and 85 Hz refresh rate).
I'm using Ubuntu 9.10 with kernel 2.6.31.17 and xrandr does not recognize the monitor correctly (see code of xrandr output). Adding a new mode did not work and currently it displays a resolution of 1200x768 which is horrible. In this version of Ubuntu the xorg.conf is not used anymore and is thus empty. As I have read you could create an entry in a new xorg.conf for your hardware which would be used by Ubuntu, having priority over xrandr settings.
But I do not really know what the monitor section in xorg.conf would have to look like, as the original screen would have to be set to 1200x768 or be disabled all together. The screens would have to be mirrored. Would the setting also work, when the external monitor is not connected to the notebook, so the original screen would display everything correctly.
Here some information about the system which will hopefully be useful for you. Please post helpful links I have overlooked or ask for more information.
My onboard graphics intel chip is capable of a resolution of 1600x1200 as it works in Windows:
lscpi output for graphics chip:
Code:
loaded kernel modules (relevant lines, at least I hope) according to lsmod (the driver from Intel web page is totally outdated and I think this is not the problem, so I didn't consider compiling a new driver)
I've just done a fresh install of Lubuntu 10.10 on an older Sony Vaio laptop. Having learned the hard way about editing xorg files, I wanted to create a backup of the xorg.conf file so that I dont have to do another install when I screw everything up. In a terminal, I typed
[Code]....
I am running kde 4.4 in virtualbox , but cannot create xorg.conf to get a correct resolution. X -configure = segfault. Older releases were fine - lenny, even ubuntu hardy / lucid.
View 6 Replies View RelatedI have set up my Ubuntu virtual machine and am trying to adjust the screen resolution because it's stuck at 800x600 presently and there are no higher resolution options. I've looked at numerous similar forms and tutorials online and they all seem to involve editing /etc/X11/xorg.conf. However, for whatever reason, this file seems not to exist on my machine. I found another tutorial on how to add a screen resolution using xrandr --addmode which added the resolution I want to the list that appears when I type the command xrandr, but when I try to apply it I get an error about CRTC 262 failing.
View 8 Replies View Relatedmy laptop screen has 1900x1280 (native resolution) and my second monitor has 1600x1080
After browsing the forums and messing around with drivers I managed to get the resolution up to 1600x1080 (from 1000x800 at install) on the laptop screen. No luck at all with the second monitor. I currently have it connected with both VGA and DVI.
my understanding is I need to use twin view to setup the second monitor. I've read several of the earlier posts but haven't been able to get it to work. Here is my current xorg.conf file:
Code:
Section "Monitor"
# HorizSync source: edid, VertRefresh source: edid
Identifier "Configured Monitor"
VendorName "Unknown"
[Code].....
I have Ubuntu (running Jolicloud) on my HP dv2000 laptop, connected to my Sony AV Receiver through HDMI to use the TV as an external monitor. However, the resolution seems to be slightly off as the outer edges of the screen are cut off. Is there a way to fix this by editing the xorg.conf file? My current setup is below. I tried adding the line "Virtual 1244 700" to the subsection "display", but when I restarted it threw me into low graphics mode. Is there anything else I can try?
I also tried setting up the resolution at 1920x1080 on the TV and kept the default resolution on the monitor as 1280x800, and as you would expect displays the entire desktop in a smaller version on part of the tv. However, the desktop is still offset, leaving the top and left margins cut off. So, perhaps I need a way to offset the screen? Is this possible in xorg.conf?
I have installed Kubuntu 8.04.2 on a USB stick with persistence to keep any changes I make after a reboot and it works fine. I then installed the 185 Nvidia driver to give me higher resolutions and it works fine.
But each time I reboot, my updated xorg.conf is replaced with the default xorg.conf that ships with that version of Kubuntu and a backup is made of my updated xorg.conf (the correct one) which looks like xorg.conf.20100409135913. I have to put the backup xorg.conf back in place to get my Nvidia driver to work with the correct screen resolutions again. Otherwise my screen resolution is too low.
What could be causing this behavor? I'm sure it not the persistence feature of the USB stick failing since a backup is made of my original xorg.conf.
I might add more information. The xorg.conf that gets changed after a reboot says "This file was generated by dexconf, the Debian X Configuration tool, using # values from the debconf database." #
1. What is the difference between files (xorg.conf and xorg.conf-vesa)
2. No matter how hard I try I can't change keyboard layout in xorg.conf-vesa (I change it in file ) but there is no actually anything changing, it starts to get annoying - for example - below goes my xorg.conf-vesa, if I uncomment and set line from
[Code]...
I've read the how-tos (thank you oldcpu!) and wikis about how xorg.conf take precedence over the section configuration files in etc/X11/xorg.conf.d/, if it exist. I also understand that the xorg.conf can be partial. If it is missing some sections, these will be taken from the corresponding xorg.conf.d section config file. Currently I'm using a xorg.conf generated by nvidia-settings in one of my home machines, due to a dual-monitor setup. After generating xorg.conf, the device sections are:
in xorg.conf:
Code:
Section "Device"
Identifier "Device0"
Driver "nvidia"
[code]....
My question is if the Option "UseCompositeWrapper" "True" will be used or not. In other words, if a section exist in xorg.conf then it's correspondent in xorg.conf.d/ will be completely ignored *or* only the lines in xorg.conf.d/ that already exist in xorg.conf will be ignored?
I'm running the ubuntu based Green OS and cant get my video card properly configured. i've already gone through the forums to figure out what i need to do to get my ATI card working but my system wont let me access the xorg.conf file. i can see it using the the GOS file editor but it wont let me save the modifications. when i attempt to edit from a terminal window with su privelages it tells me that /etc/x11/xorg.conf does not exist. i've even tried booting into recovery mode and using the root instead of the sudo command. nothing i've tried will let me open the file.
View 3 Replies View RelatedI looked for a solution to this,and found a thread for it ,but I dont know how to do what it says.Here is part of it by the user "cameronol": There is a bug in Ubuntu 9.10 Karmic with the default /etc/X11/xorg.conf involving Nvidia. receive the error"Failed to parse existing X config file '/etc/X11/xorg.conf'.Then he posts:
[Code]...
Then he says to delete the first section with the default screen,and it will be fixed.But HOW do I look for the /etc/X11/xorg.conf file to edit it,and how do I edit it?I am new to ubuntu,but I have learned to use a terminal(I think)It seems to be just like the "run" box on Windows.I did a search for the file,but came up empty.I want to fix this cause every time I restart,I have a low resolution that is impossible to work in.
I have used nVidia my entire linux life (about 5 years clean and sober from M$). Recently, I have switched over to an ATI Radeon HD 5550 card. After many trial and error setups, I finally got the resolutions and screens set properly with a xrandr command, which I have now added to a shell script in ~/.kde4/Autostart. It has worked for me for a while now, but I really would like to get it set in the xorg.conf.d files so that I don't have to wait that extra few seconds after login for the screens to fix themselves.
Is there an easy way to take what xrandr does and export it to the xorg.conf.d files? If my video card recognizes my default monitor as DFP2 and the tv that I only sometimes use with this computer as DFP1, how can I ensure that the login screen for openSUSE/KDE4 appears on my default screen (an issue that drove me nuts a few months ago when I tried Ubuntu to see what all the fuss was about)?
My xrandr command that I use to fix it all is:
xrandr --output DFP2 --auto --pos 0x0 --primary --output DFP1 --auto --right-of
I am using the proprietary Radeon driver from the ioda repository. DFP2 is a monitor which has a optimum resolution of 1920x1200, and DFP1 is an 1080p HDTV. I can not reverse the output plugs for the screens even though my monitor is an HDMI monitor because I use the actual HDMI port on the video card to output audio to the television and the other plug is a DVI that I convert to HDMI for the monitor.
Sorry if this was well covered here when most up-to-date Slackers moved to 13.0, but I have just jumped from 12.1 to 13.1. Generally very happy that I do not have to think about xorg.conf as I always found the structure of this conf file a tad confusing. However if I do need to (for example) change my video driver (I might for example want to try the nvidia driver from NVIDIA) or configure my touchpad - how do I do this ?
I understand that xorg.conf can still be created. If I do so, do I have to put all the stuff in that used to be there or can I just add the stuff I need to make the changes I am looking for?
i i use ubuntu 10.04 and i buy a mouse, and i cant install it. i read on forum i need to put :
Section "ServerFlags"
Option "AllowMouseOpenFail" "true"
EndSection
[code].....
wireless via Bluetooth � 3-button laser mouse with scroll wheel � resolution 1600dpi, adjustable on 800dpi � range up to 10m � computer with Bluetooth or dongle required � 2x AA batteries required
i lost touchpad functionality during gdm login (i cant tap clicking) after playing with xorg.conf
would somebody kindly paste-ing their xorg.conf for eee pc (1000HE) ?
I just did a net install on an old powerpc G4 and it seems pretty successful.except i cant change any of the monitor settings from the control panel in gnome (or LXDE)its showing 'not recognised' and only allows 768 x 1024 in very restricted colour.I dont think there is a hardware problem:
- the monitor is a generic old CRT which has worked fine with everything before this.
- the display card is an AGP 32Mb - original with this G4 and was working.
- the computer works great in Mac OS10.3 - (but OS10.3 doesnt support flash or up to date web browser any more, hence trying debian).
i have searched debian forums and various sites, but i couldnt find a fix. It looked like i should edit xorg.conf file but I am not able to find it. I looked in /etc/X11 - but not there.could someone tell me please, do i need to find xorg.conf?
I install Debian 6 in my thinkpad W500.
W500 has two video card : Intel integrated and ATI discreted .
Now I am using Intel Integrated video card . I find no xorg.conf file in /etc/X11 .
How to make Debian 6 using two different video cards through changing BIOS setting ?
Cannot edit xorg.conf on Fedora13. I do it from the root but changes is not saving.
View 7 Replies View RelatedI am running Crossover Office on a laptop on OpenSuSE 11.2 with a fair bit of success (Outlook is still twitchy related apparently to the http stack). But whenever I do disk I/O to a windows app and I have a second monitor plugged in it flashes to black.
In prior OpenSuSE versions I used to be able to stop this by adding entries to disable the TV output in xorg.conf but now it appears that there is no xorg.conf in use. How do I disable this in the post-sax2 era?
Dell Lattitude E6500 4Gb x64_86