Hardware :: USB Hard Disk Not Recognized After Using Shred
Aug 20, 2010
This hard disk is an old Maxtor (60G) extracted from an old computer, working fine. I placed in an enclosure and connected it to my Linux Box (Slack 12.1). It was recognized immediately and mounted automatically. However, before giving away the hard disk, I tried to wipe the data by running shred /dev/sdf At some point, I realized that it was going to take a long time, and aborted the process and disconnected the enclosure. Now, none of my Linux boxes recognize the disk inside the enclosure. Here is the output, when I plug in the usb cable, while using systemrescuecd on my desktop computer:
Quote:
Aug 20 00:58:17 sysresccd kernel: [ 3582.116029] usb 2-6: new full speed USB device using ohci_hcd and address 12
Aug 20 00:58:17 sysresccd kernel: [ 3582.316054] usb 2-6: not running at top speed; connect to a high speed hub
Aug 20 00:58:17 sysresccd kernel: [ 3582.322051] usb 2-6: New USB device found, idVendor=04b4, idProduct=8613
Aug 20 00:58:17 sysresccd kernel: [ 3582.322054] usb 2-6: New USB device strings: Mfr=0, Product=0,
[Code]....
Is there a way to use this hard disk at this point?
I have 2 Hard Disks in my computer both of them show in File & Folders, and they are both formated by Ububtu, I use the 2nd one for my Data storage as it's the larger of the two. The problem I have is that certain programs just don't see it! For example Album Shaper sees the boot drive but not the 2nd one which has all my photo's on it. OpenOffice is not a problem it sees both drives. But there are a few programs that just don't see it.
after installing Ubuntu on one WD 500 GB hard disk and after making mistake and pasting wrong code into Terminal:my OTHER WD 500 GB hard disk that was also in the system (I guess it was "hd1") - died.The problem must be, I guess, I typed wrong code: "hd1,1" instead of "hd0,0".)500 GB (NTFS) of data was on that other (non-Ubuntu) hard disk, and now I can not access it anymore. While booting, system gives "Hard Disk Error" warning and stops.One again: I installed Ubuntu od one hard disk and at the end of instalation I pasted wrong code for GRUB, giving address of another hard disk. Now that other hard disk has error and will not work
I have a sata 320 gb with mandriva linux 2009.1 on it.And it is what curently atached to my cpu. It is shown as 'sda' in the partition table.I also have another 40gb hard disk with windows xp installed on it.It is shown as 'hda' in the partition table . Now what i want to do is attach this 40gb hard disk to my pc and configure grub on my 320gb hard disk('sda') so as to boot windows xp(which is residing on the second hard disk,'hda')Can anyone tell me if what im doing is feasible or not? If it is feasible,can anyone suggest me how to get it working. I know i just need to add 2-3 lines to my grub.conf, but dont know what exactly i need to write.
I had a dual boot (windows 7 + debian), both of them installed in my internal hard disk, with the GRUB in it. I have recently installed a second linux distro (mint), but I put it in an external hard disk. Now the GRUB allows me to boot any of the three operating systems, but I need the external disk to do it. It seems that after the mint installation the GRUB is now working from the external disk (if the external disk is not connected, the machine does not boot.) �Is there a way to change the location of the GRUB, to the internal hard disk of my laptop?
I was using Terminal and browsing a directory in my home folder. My "home" directory is located on "/dev/sdb1". When in Terminal I typed "ls" in one of my directories and the output was garbage. The output didn't show the files in the directory. I think it said something like, "input/output error". Unfortunately, I didn't write the exact error down. Instead I rebooted.The hard disk with the problem is:
Code: $ sudo hdparm -I /dev/sdb [sudo] password for brian:
Trying to install Fedora 12 using the 6 CDs. Trying to install on an older x86 box.Problem is that when detecting my hard drive, Fedora 12 recognizes it as a sda hard drive instead of hda hard drive. I have no SCSI connected to my computer what so ever. It's an old fashion PATA Western Digital hard drive.If I proceed with the install, Fedora 12 only installs 200MB of the OS from the first CD only. No options for additional software or anything.
I recently bought 320 GB Trancend external hard disk and working fine days back.Earlier i could copy from and to the hard disk with out any issue. I dont know what happened after that now i am not able to write any files in to the external hard disk. This is not NTFS formatted device. here is some of the out put from terminal.
Code: sundar@sundar-sundar:~$ fdisk -l Disk /dev/sda: 120.0 GB, 120034123776 bytes
I have two internal harddisk. Harddisk 1 has ubuntu, fedora installed and harddisk 2 has ubuntu installed. I normally connect either one, and use it. How can i always keep connect both harddisks, and at the start, select from which harddisk to boot? Or it's not possible?
is there a way to write/unpack .qcow2 hard disk image directly to real hard drive in Linux?(I know it's possible to unpack .qcow2 to .raw and then dd to drive, but I'd like to skip .raw since its large)
I created a thread about a problem a I had with my hard disk clicking whilst idle little while ago and I may now have stumbled upon a possible solution. The strange thing with the problem is that Ubuntu/Kubuntu didn't cause this problem but Opensuse 11.2 does.
I installed Fedora 13 to have a glimpse of what all the fuss was about and noticed that I had the same problem (hard disk clicking whilst idle ~ every 20 secs or so). Now there's a wiki on this subject and a few bug reports: [url]
Problem Description
Some ATA harddrives perform very frequent head unloads under Linux significantly shortening their lifespans. Root cause
The inactivity timer for head unload is configured too aggressively either via ATA APM (Advanced Power Management) feature or other non-standard means. Such aggressive settings are very fragile to changes in IO pattern and under Linux many such drives unload their heads only to re-load them shortly. Note that this relentless unloading/reloading cycle can also be triggered under Windows by installing programs which can alter the IO pattern (e.g. certain vaccine programs which runs in background).
Now two of the listed models with this problem are basically identical to my model (Dell Inspiron 1520) and basically share the same hardware: Dell Vostro 1500 and XPS 1520.
The workaround listed is to:
set APM to 254
Furthermore, there is a script: Storage-Fixup which can also be downloaded from opensuse software search. Indeed there is a report of this for a Vostro 1500: Gmane Loom
The report suggests looking at: Disk Power Management - openSUSE which lists a method to create a configuration file to management disk power management:
My question is whether I could download the storage-fixup rpm [url] has a description of it and it can be found: Software.openSUSE.org) and install it to (hopefully) solve the issue or should I follow the method given in: Disk Power Management - openSUSE
ran out of space in my /home dir. Have a second hard drive to install and would like to designate it as additional space for /home. I do not want to mount it as a dir inside my home I would like it to simply work as though my /home simply has more space available to it.
I'm trying to resize a partition on an IDE hard disk to use the entire disk but can not get more than a 309GB partition. I can get 295, 300, 301, 302GB, etc... fine but start getting problems with anything over 309GB. I get the following error with 310GB or more:
error: block relocator should have relocated 533 Warning: You should reinstall your boot loader before rebooting. Read section 4 of the Parted User documentation for more information. I am using Slackware 12.1, GNU parted 1.8.8, ext2 filesystem.
I have a 2nd hard drive (500 GB) that I keep my media on. When I tried to access it, it wasn't showing up in places or even places > computer. I used system > administration > disk utility. On the left hand side it shows the drive listed with the type and model number. Right under that it shows 500 GB Hard Drive unrecognized unknown or unused. If possible I would like to recover the media on this drive. I had setup this drive as ext3 and had it mount /media/sdb1. I can go to /media/sdb1 in the file browser but nothing is there.
i'm trying to install mint 8 on a new hard drive but my pc doesn't recognized it. neither does the live boot mint cd. when i get to create partition it just hangs there.do i need to format the new drive using my old one first?
I had windows 7 installed on my machine and decided to go with a ubuntu win7 dual boot. The install went fine, but Ubuntu doesn't see my second HDD as anything but empty. My second HDD I set up in win7. It is actually two 320GB HDD striped together. It is holding alot of data that I would like to be able to access from both win7 and ubuntu.
When I run fdisk -l in the terminal I get: Disk /dev/sda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xf1c572ca .....
So Ubuntu sees the two HDD, just not as one with all my data on it like I see it in windows. Is there a way to set it up so I can use that second HDD (the two stripped) in both win7 and Ubuntu?
When i try to install ubuntu 10.04 on my desktop i get through the first 3 steps which are Language, Region, and Keyboard. when i get to Prepare partitions, there is nothing there (same problem with 9.10). I followed the steps of another thread about removing the raid settings and I am sure i did that correctly but it did not work, when i try to find my drives in terminal they can not even be found.
Both of my drives are SATA, one is 250gb, other is 500gb. They are both recognized by other operating systems. I have switched the SATA headers that they are plugged into. I really am just not sure what else to do here. Im not totally stupid at linux, ive been using it for a few years and i have taken two classes for linux in the past year. I really feel dumb for not being able to figure this out :/
I am trying to install this OS. However no matter what I do the UBUNTU instllation CD doesn't recognize the hard drive on which I would like to install the OS on.
I currently have two SATA hard drives connected to my computer. MY primary is my Windows 7 drive and my second hard drive is my spare.
When i load up UBUNTU and get to the window where I can select which hard drive/partition to install to my second spare drive isn't there.
I have an external hard drive that connects through an expansion card with eSATA on it. It was partitioned and formatted as NTFS in Windows but isn't recognized in Ubuntu 10.04.
I have a computer with 2 internal hard drives and one of them doesn't show up in the bios until I reboot. Almost every time. Does this mean the drive is going to fail or the cable is bad or what?
I booted from fedora 12 cd, My problem is the install does not recognize my ide disk.
lspci -> ide interface vt82c586a fdisk -l /dev/sda1 swap -approx 2g /dev/sda2 linux 20 g /dev/sda3 linux 54 g lshal -> pata_via
I tested the disk with seagate diag it reports no errors. I used Partion manager and created three partions & formatted them. Other distros see the disk , I am trying crunch bang it installed with no fuss. I have googled & looked in known issues pages.
I am trying to run You Don't Know Jack in wine - appdb says it has Platinum status, so compatibility shouldn't be the issue. My laptop doesn't have an optical disk drive. So, I ripped the disk to an iso image, mounted it with gmount-iso, and tried to open the program.
The program still says the disk is not inserted. I know on previous laptops with optical drives, I could mount an image on /dev/cdrom0 or /dev/sr0 or whatever and it would be recognized. My /dev directory had no cdrom0 directory, so I made one. I mounted the iso there but it still didn't recognize it. I've tried in my home folder, in /cdrom, and in my newly-created /dev/cdrom0 but no luck.
When trying to install Kubuntu 10.04 32-bit (or Ubuntu 10.04 64-bit) it does not show me any hard drive to partition in the 'Disk Setup' (I've clicked all the buttons on that screen to see if I can encourage it!) and will not let me past that point in the installation process (because, obviously, no root file system has been defined). I have done something very bad to my computer. As an aid to selling my computer, I decided to (try to) install Windows 7. I booted into a live Ubuntu CD and used Gparted to reformat my hard drive. After several issues with the Windows boot CD I decided to pull up FastBuild Utility, and did something which included deleting LD and Defining LD again. Didn't make any difference with the Win 7 install. I am now trying to return my computer to a functional state in the sanctuary of Kubuntu 10.04.
Tried installing Win XP which I have installed successfully on another computer. Got an error message: "Setup did not find any hard disk drives installed in your computer" - presumed that was because of something I did with FastBuild Utility (2006). I've tried as many different options in this as I think could make a difference. Booted into DR-DOS and deleted partitions and created a FAT 32 partition. Booting into the live Ubuntu 10.04 CD again and used GParted to create an NTFS Primary Partition taking up all the hard drive. As above and deleting all partitions in GParted. Checking into BIOS and changing the SATA Operation from 'RAID On' to 'RAID Autodetect / ATA' (Now changed back again to the default 'RAID On.').
Loaded Defaults in BIOS - I've been running Ubuntu 10.04 x64 on it since it came out with these settings. At all points I have tried to install Ubuntu 10.04 64 bit, Kubuntu 10.04 32 bit (and Win XP) with no success. In the Kubuntu install, when I get to the Disk Setup part of the installation process it offers me no information whatsoever. My hard drive has all partitions deleted because of my last action in GParted. May need to define a partition. What as? I'm still convinced that my playing in FastBuild Utility (2006) is probably the root cause of this, and so quite likely to be a good place to go to solve this. I think I've set everything as it was, but can't be 100% on that.
I'm very new to Ubuntu. Now that I have it installed, my computer doesn't recognize my external hard drive or flash drive. How do I access my external hard drive and flash drive? I'm also trying to get Rosetta Stone to work using Wine, but having a heck of a time. I've searched the forums and have found some similar topics, but nothing that really helped me.
