Earlier i was using red hat on my laptop..then i installed windows 7...so grub is replaced bt windows boot loader....nw it is showing grub error...how to remove this grub error....so that both can work fine?
View 1 RepliesI am new to Linux. I have installed RHEL 5.4 on my PC with preloaded Windows XP.
Windows was set as the first boot kernel. So if i do not choose which OS to be loaded it will load Windows by Default.
Today I got an error saying GRub Loading Stage2 read error.
Have installed ubuntu on a separate partition on single hard disk and system initially worked on a dual boot basis with windows xp. However after installing most recent series of updates computer is failing to boot.
Error message is 'error : no such device : 6937cabe-f115-455b-a248-6f8d46f80682.' prompt showing is 'grub rescue>' am now unable to access either windows or ubuntu.
Toshiba/Celeron/multibootI just installed Salix KDE. The install went well, afaIk...Salix does not appear on the grub, and I in fact have no way of knowing if it even exists on my machine. I have not checked anything via the console. I do not know how. All other OS's on the HDD are present on the grub, and are unaffected.I am running Kubuntu 10.04 LTS currently.
View 12 Replies View RelatedI would like to know when usb inserted, its showing cant mount when i clicked details its showing bad blocks in beginning , and smething in /dev/sd6. Can i knw why usb drive cant be mounted automatically , even if its set to do so, and to cope the error mentioned above
View 1 Replies View RelatedI've been running openSuse 11.2 for a while on my notebook.Today I turned it off at work and came home. When I tried to turn it on, it boots, shows a black screen written 'GRUB' and then NOTHING. It doesn't complete the boot process.
View 9 Replies View RelatedI had just configure RAID 1 on my IBM X3400 Server ..Partition information is md0 boot , md1 swap and md2 is root ....but after resyn when i run cat /proc/mdstat I realize that md0 and md1 is ok and present with [UU] status. BUT the md2 is showing on one [U_].. that means my root partition is not properly in RAID 1..
Please suggest how can i make it active in both drive. Or i need to reinstall complete system again. Screen shot attached
While i installed rpm package its showing error of failed dependencies n in another case cant create transaction lock on /var/lib/rpm_db.000
View 4 Replies View RelatedWhile loading a rpm package its showing error of failed dependencies so wat to do for dat pls guide me
n in another case its showing cant create transaction lock on /var/lib/rpm/_db.000
I have created a shell script to customise mv command, now i have achieved to accomplish all the functionality of mv by using alias. But i found difficulty in accomplish the funcionality with options [Like mv -i or mv -f etc.]. I thought about logic which check the first argument whether its starting with a minus [-] or not. if its starting with argument it will set a flag and execute accordingly. But whenever this condition is checked it shell script will throw error of destination operand missing. But the same will work with out option.
Note: I have used an minus[-] expression for decreasing a counter on the script above. The below mentioned is the portion of script. Sry for troubling Im not gud @scripting.
for i in $*
do
{
argument=`expr $argument - 1`
if [ $argument = 0 ];
then
exit
[Code]....
I am having a problem installing SLES11 on a new server. It goes fine through the setup until it gets to GRUB, it gets me the following error message: Error occurred while installing GRUB
[code]...
I cant continue the installation without this
Ubuntu 9.10 was set up to handle the booting selection - previously I thought it was xp but Ubuntu 9.10 "did" it. The system started out as a xp / ubuntu 9.10 dual boot on a 400gb drive. xp has 210gb, ub has 80 and their is a 100gb shared storage. Xp was installed first and then I followed a guide over at linuxconfig.org to get ub installed so that I could select which OS was wanted at boot. Ubuntu manages the boot up menu (Went back to look at my notes from the original setup) The owner tried to update to ub 11.04 and afterall was said and done the machine now boots to the message
error file not found grub rescue I can't say if 11.04 was properly installed or not. Ask whatever you like and I'll give the best answer I can. I think the xp install is okay but I can't say for certain as I don't know how to boot it outside the bootmanager at startup. Data has been saved so if I have to blow it all away and start over I can but I'm hoping I won't have to.
I have a dual boot system with ubuntu 9.10 x64 and Windows 7. Everything has been working fine for a a long time but yesterday I tried to delete an unused partition through the Disk Utility in ubuntu (System->Adminstration->Disk Utility) and everything was messed up. I used to get the "Grub error: Unknown filesystem". I managed to create an ubuntu bootable usb and followed some tutorials for fixing grub but all i managed to do is to get another error: "Grub error: No such disc". After some experimentation i got
"Grub stage 1.5" which gave me a grub> command prompt./dev/sda is the drive containing Windows and Ubuntu.
Code:
[ Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ==============================
=> Grub 0.97 is installed in the MBR of /dev/sda and looks on the same drive
in partition #6 for /boot/grub/stage2 and /boot/grub/menu.lst.
[code].....
My brother has Tri boot Ubuntu ,7 and Vista ..GRUB2 is the bootloader..The problem : At boot after the Lenovo splash disappears , there appears some 4 to 5 lines of error , error:syntax error GRUB or similar..This is visible only for a fraction of a second before the GRUB2 menu pops up...
The OS es load properly on selection in the menu so no loss of functionality One another problem is there is no OS highlighted by default and the timeout message "Automatic Boot in 10 Secs" does not appear Reinstalling GRUB does not solve the issue
When I try to connect a projector to my laptop (already running) and hit the fn+f7 (the designated button for switching screen), nothing happens. I see "no source found" on projector screen and my laptop screen works perfectly. Now if I restart the laptop with the projector connected, I see all the intial booting messages on the projector screen (not on my laptop), then the gnome login screen appears on both the projector screen and laptop (when the login screen appears on laptop it looks like it has lower resolution than my usual laptop resolution). But immediately after I log in, my laptop screen goes blank, and projector screen becomes the only active screen.
If I restart without the projector, again all normal operation on laptop screen is restored.
I feel like I am missing some very silly options. Any help is appreciated.
Here is the output of xrandr when the laptop is connected:
Code:
we have an oracle application server on red hat 4.6 upon booting it comes up with error: attempting boot from hard drive (c GRUB)
View 2 Replies View RelatedI was foolishly messing around with Grub trying to get it so it only show my two most recent kernel versions of Ubuntu and Windows 7. The tutorials on how to do this were not clear, so I deemed it not a big deal and ultimately didn't end up making any changes. However when I restarted to boot into Windows 7 it was gone for Grub's boot list. I looked at the grub.cfg file and in it under os-prober, where i'm assuming Windows 7 should be there was only Vista (which wouldn't boot when I tried it, just a black screen). I had upgraded from Vista over the internet when Windows 7 first came out, then installed Ubuntu and it worked fine until this. I am using 64-bit Ubuntu 9.10, and have Grub 1.97 beta~4 installed, which was installed with Ubunutu.
View 9 Replies View RelatedI installed 64-bit 10.4 LTS side by side with CentOS, and after install done, grub only showing ubuntu.
I ran 'os-prober' and it detects my CentOS install. I ran 'update-grub' and it updates grub, but doesn't add CentOS. I thought that should do it. What did I miss?
I Currently am running Ubuntu 10.10 on a hard drive with three partitions. One with Ubuntu, a Media partition (Music, Videos, pictures, etc.) and the last is my Windows 7 installation. I can acess all of these partitions in nautilus as well. However when I start up my computer it automaticly loads into Ubuntu and when I manage to see Grub I only see 3 Entries Which are the Ubuntu kernel, Ubuntu recovery Kernal and memtest86+. How do I make Grub recognise my Windows 7 Installation?
View 9 Replies View RelatedI installed fedora about a week back, and when I first started it, it told me that it had a kernel failure, and showed me a notification on the right hand bottom corner and asked me if I wanted to submit the report.
Recently, I started noticing that GRUB shows 2 fedoras and Other (which is XP)
This is what GRUB shows me:
Fedora(2.6.29.5-191.f11.x86_64)
Fedora(2.6.29.4-167.f11.x86_64)
Other
Just now, it didnt boot into fedora saying it failed loading something, and I ran fsck, it showed 2 errors and fixed them , then I was able to get into fedora.
When I try and boot my Debian computer I get the messages: Grub Loading stage1.5. Grub loading, please wait... Error 15 Is there any way of recovering from this - or is it simply a fresh install? I was attempting an upgrade from Lenny to Squeeze and despite a few hurdles it looked like it was all happening. Got the new kernel loading, and the new grub. It looked as though grub2 was working so I ran the grub-remove-legacy-support command (something like that) and now my computer won't boot grub or Linux.
I'm assuming the MBR on my harddrive is lost, however I don't know what state the partition is in. I'm guessing that maybe this has been lost as well. I tried a few tools from the Ultimate Boot CD but nothing here was able to re-install my grub or boot from any partition or even mount my file-system. I'm fearing the worst but would like it confirmed before I blow it all away with a new install.
I just installed OpenSuSE 11 and after it was done installing and i rebooted, Windows doesn't show up on the boot screen I only get the default OpenSuSE and Fail Safe options.
All i know is that vista is on sda3 when i partitioned my drive. Here is my menu.lst entry for windows:
###Don't change this comment - YaST2 identifier: Original name: windows###
title windows
rootnoverify (hd0,8)
chainloader (hd0,0)+1
I am working with a acer netbook that I originally had WinXP installed on. I downloaded Ubuntu 9.10, transferred the iso contents to a bootable USB drive and installed Ubuntu. I remember during the setup process that I made sure I chose the option to install on one partition. There is only one partition on my netbook with a small second partition as a swap.
After the installation process and reboot I noticed the grub menu would pop up every boot up giving the list of operating systems of which XP was included. I then ran the update manager and updated 9.10 with all updates. After rebooting the grub menu again showed but the option to choose XP was now gone.
Now everytime I boot up the grub menu shows. How can I modify grub so it will automatically just boot to the OS.
Every time I update my kernel (today with 2.6.32-25-generic), I always have to manually run "sudo update-grub" or ells the new kernel does not show up on reboot??? Is there a config some place to get it back to automatic?
View 6 Replies View RelatedI have dual-booted Windows XP and Ubuntu. Because Ubuntu 10.04 doesn't have the required proprietary drivers for my system, I chose Ubuntu 8.04. The installation procedure went well, the drivers are there, everything's perfect but... there's a problem with the GRUB menu that appears just after launching my laptop.
When I first installed Ubuntu it showed Ubuntu (and some letters and numbers), another instance for recovery mode, some memory test lines (I guess there are two of them) and Windows XP.
But after I used the software updater in Ubuntu (to make it up-to-date), the grub bootloader shows two more lines - and those are the same as the first two - Ubuntu (with some letters and symbols) and Ubuntu recovery mode.
Why are those duplicates there? I've never installed another Ubuntu OS on my PC. Because at the moment I have two Ubuntu and two Ubuntu recovery mode lines .
I have both 8.10 and 10.10 installed on my hard drive, but whenever I boot the GRUB (I believe it is GRUB Legacy not GRUB2) only shows 8.10. Is there any way to get it to see my newly-installed 10.10?
View 9 Replies View RelatedWhy is Grub2 not displaying Fedora partition??I know fedora uses Grub legacy,whereas Lucid uses Grub2 and therefore i installed fedora 14 WITHOUT boot loader.
View 2 Replies View RelatedMy laptop came with Vista and I added Linux Mint 6 (based on Ubuntu 8.10 Intrepid Ibex) all is good for a year or so. Added Ubuntu 10.10 to my desktop, loved it, wanted to add it to my laptop...oops.
Installed the main version from a LiveCD, did the the easy multi-OS installation.
GRUB-0.97 is what boots my system though looking at boot script I do have GRUB2 somewhere.
Currently, my boot options are:
1. Mint 6
2. Mint 6 (recovered)
3. Mint 6
4. Mint 6 (recovered)
5. memtest 86+
Other operating systems
6. Vista/Longhorn loader
7. Vista/Longhorn loader
Sda7 is where Ubuntu should be installed. GPARTED says its ext3 file system and bootscript says ext4.
I did find the forum post on purging and installing GRUB2 though I'm not sure if that's what I need to do, or try to reinstall Ubuntu w/o also doing partition resizing at the same time.
The output from my bootscript:
Code:
Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ==============================
=> Grub 0.97 is installed in the MBR of /dev/sda and looks on the same drive in partition #5 for /boot/grub/stage2 and /boot/grub/menu.lst.
[Code]....
I have a computer that only runs ubuntu and have decided to put fedora on. I put fedora on the computer and made a new partition for it. When I turn the computer on, it logs straight into fedora not even showing me a grub menu. Is there some way that I can update grub so that it knows that ubuntu is also installed
View 1 Replies View RelatedLast week i decided to give the 11.04 alpha 2 a go on my laptop but compiz is currently too unstable for the OS to be of any use so I reinstalled 10.10. In doing this I deleted all partitions and started completely afresh. Strangely since then I have kernel image 2.6.38-1 at the top of my grub menu but if i try to boot it i get either a single blinking cursor or a kernel freeze. I cant find any reason why 2.6.38-1 should be in grub on 10.10.
removing it from the config files as im not used to Grub2 and have been told i cant just directly remove it from /boot/grub/grub.cfg.