Have VMWARE workstation 7. Have to extend partition /dev/sda1 mounted to /home/user
1. Originally /dev/sda was 10gb I've extended device via VMWARE to 30gb.
2. When I do: fdisk /dev/sda it tells me that /dev/sda 30gb
3. when I check: df -h /home
it shows 10GB
4. How I can make Linux see the 30gb at /home/user?
I also tried to use Gparted but I couldn't install it :(
My root partition is completely full and I want to extend it.
df -h :
fdisk -l
I would like to know if is possible extend a partition using one disk. I have 50 GB on /dev/vdf2 and would like to add on:
/dev/vdc1 50G 6.4G 41G 14% /home3
And this partition will have 100G of space..
How can I extend /home or / partition through LVM. Is this possible ?
View 8 Replies View RelatedI have created one partition. Now I want to extend that partition without formatting it.
View 3 Replies View RelatedI know there are probably alot of threads about lvm however they aren't addressing my problem. I want to extend the PEs available in a VG. This VG already has LVs and those are active and mounted. From what I read from the manpages of pvresize this should be perfectly possible.
Code:
pvresize resizes PhysicalVolume which may already be in a volume group and have active logical volumes allocated on it.
I did the following steps and wonder if anyone has the same issue. THe machine where I am talking about is an ESX VM.
1. Resized the vmdk in ESX (+1G)
2. Let the kernel reread the device geometry: echo 1 > /sys/block/sdc/device/rescan
3. fdisk shows me the new size... so far so good
4. I resize the partition using fdisk (remove, recreate) and gave it the 8e type (lvm)
5. wrote config to disk
6. executed partprobe
7. pvresize /dev/sdc
Here it goes wrong! Pvresize says in the verbose output it sees the same size however at the end it says the pv has been resized. I have seen when I put volumes "offline" using vgchange -a n vg on a test machine, and then try pvresize it seems to work ok. This is against what is in the manual as it says pvresize should work on online mounted volumes.
Here is screenshot showing my current partition in Gparted.
Screenshot-1.jpg
What I want to do is shrink the one (Ubuntu) and extend the other (XP) so that that they are more or less the same size. How?
I have a disk partitioned, with windows on on one partition, ubuntu appears to be installed on an extended partition ... and iv run out of space... i need to extend the partition that ubuntu is installed on by 40gb
I have tried downloading gparted... burning it to a cd and then booting from the cd .. but i get upto a message that says use at your own risk then my system just reboots ....
My linux server working with LVM partition and with /boot partition, now my /boot partition is full, now i need to extend my boot partition. can i know how to do it, without any data loss.
View 5 Replies View RelatedI have my harddisk partitioned with fdisk. It has seven partitions. I have some important data in my /home partition. The /home partition is almost full. I want to extend the size of /home. Mind you I'm not using LVM. Can I use LVM now and add another harddisk to extend the /home partition. Will I lose my data. Or do I have to re-install linux?
View 3 Replies View RelatedI have an Asus eee, it has a solid state drive which has been partitioned with a 4GB and 8GB partition. I installed Fedora 14 onto the 4GB partition but I am running out of space. I have formatted the 8GB partition with ext4 but I am unsure the best way to create more space for the default installation. Can I extend my / partition onto the 8GB partition or possible move the /swap partition onto it?
View 5 Replies View RelatedI have 60 plus GBs of free space left in my Vista partition that I would like to devote to my ubuntu install.
View 9 Replies View RelatedIs there any way to use unallocated space to extend a partition that isn't close to that partition? there is an image attached, I can extend /dev/sda2 but not /dev/sda1 ( the one that i want to) I used the live cd to run gparted.I had to move /dev/sda2 to to the right and then extend /dev/sda1
View 1 Replies View RelatedI want to run gparted off the cd so that I can extend the ubuntu partition of my computer...I hdownloaded the gparted iso file and burnt it onto a CD...but how do i run the software?.... there appears to be 3 folders on the cd (isolinux, live and syslinux) and two other files 'copying' and 'g-parted live version' - these two are both text files...
View 9 Replies View RelatedI am dual-booting 11.04 alongside windows 7. I shrunk my w7 partition, and would like to extend my ubuntu partition to fill up the remaining space. When I boot from GParted live cd, and attempt to 'move/resize' my ubuntu partition, it simply fails. It doesn't really give an error message either, simply 'failed to move/resize [partition name]'
View 4 Replies View Relatedi want to extend my existing partition size,but it should do it without formatting my operating system.i don't have the solution.Is this possible?if possiblsolution.hope somebody should give the answer
View 5 Replies View RelatedI have a dual boot Ubuntu 10.04 and Vista laptop.
My Ubuntu partions /dev/sda4 extended, which contains a /dev/sda5 ext4 and a /dev/sda6 ntfs partition.
Vista is on /dev/sda2 ntfs. I would like to wipe vista out, turn off dual boot (if possible) and use the space taken by vista to extend my /dev/sda6 ntfs partition in ubuntu.
I have installed 1tb hard drive and would like to partition as follows:
1) / - 20g
2) /swap - 6G
3) /photos /150g
4) /videos /500g
5) /audio /300g
After 2-3 partition an extended partition automatically created in which I am not able to create specified capacity i.e., say I want 150g of /photos partition, the /videos partition is automatically reduced and a free space at the end appears. Some free space is always there which i am not able to understand. Nevertheless i clicked to create, but I get an error viz. 'device not created'.
I knew how to mount it and I was able to view files and folder in it but I don't know how to copy files using CUI (Command not GUI) mode. I have six separate iso files and I want to make a DVD in the removable device.
View 1 Replies View RelatedI know I have done this command on out Red Hat systems. But for some reason in CentOS its giving me problems. I am trying to add more space to / as its at 100% full. Not sure what filled up the 4G is assigned to it but I did load Virtualbox and a widowsxp system.
Here is what i have:
df
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/hdc3 4061572 4050416 0 100% /
/dev/mapper/rootvg-rvg_datalv
253934980 313572 240514208 1% /data
[code]....
When CentOS boots up, it tries to determine the IP for a network device (eth0) and fails.
'Determining IP information for eth0... failed; no link present.'
I'm curious to know how, after booting up, I could set the IP information for a wireless device, wlan0, manually. Another way of putting this questions is: if CentOS is able to determine IP information for a network device on bootup, what settings is it configuring exactly?
I've added a second drive to a system and I need to extend the lvm and the filesystem to the second disk. Is there a way to do this online with centos 5.5? I specifically need extending the actual ext3 filesystem which seems to be the trick part.
View 8 Replies View RelatedI'm trying to use xrandr to extend the desktop on my laptop to my lcd monitor. I have tried a few different ways but no matter what I do the desktop will end up on my LCD and the laptop is the extended desktop. Anyone know where I am going wrong? Here is the command I've been using:
xrandr --output LVDS --auto --output VGA --auto --left-of LVDS
I have installed live cd on usb pendrive. Everything works great. How can I find out which device driver it is using? Where are the device driver files stored? How do you specify the device driver when mounting a device?
View 3 Replies View RelatedWhat I need is a program that will extend a X-windows display over a network, similar to nvidia's TwinView (which I am already using on the main machine for its 2 current monitors).However, I cannot use Xdmx (as suggested by all the threads I found), as I would like it not to require me to manually start the x server and viewer, and have all the machines must be running a *nix OS, which won't work for me, as the secondary machine is running windows.I would also like it to hopefully use VNC to share the desktop, as I would be connecting to it from a windows machine over ethernet.By "extend" I mean one that would, say, for example, add another X display with a given resolution and position and serve that over VNC. I have yet to find any programs that will do this.
View 1 Replies View RelatedI wonder if this is possible to extend or regrow the Linux hard disk partition from 8 GB to 20 GB without losing the existing data on the partition ?at the moment this Ubuntu Linux is deployed on top of VMware and I've just regrow the hard drive from 8 GB into 20 GB but can't see the effect immediately.can anyone suggest how to do this without losing the data ?
View 9 Replies View RelatedI have had a Supermicro X7DCL-3 motherboard based machine, running CentOS 5.2 x86_64, recently upgraded to 5.3.Strangely enough, although I must have installed the 5.2 using DVD disk, the running system does not show the DVD drive. The machine was not used very much so I noticed that only today, after the update. There is no trace of it in 'dmesg', thera are no /dev/cd* and/or /dev/dvd* devices. The IDE controller is IT8213 (as shown by 'lspci'). In 5.2 kernel (2.6.18-92.el5-x86_64) lspci says "unknown device". I have checked the /usr/src/kernels/*/.config files and both kernels (5.2 and 2.6.18-128.el5-x86_64 of 5.3) seam to have the support for that controller added into the kernel:CONFIG_BLK_DEV_IT821X=yAny idea why it is not working? The Supermicro has apparently noticed this also as their OS compatibility chart lists the IDE interface for that motherboard as supported up to RHEL 5.1 but not for 5.2.
View 2 Replies View RelatedI'm experimenting with a K8055 board, connected through USB to our Asterisk server,running on CentOS. If I connect the device I can see it being connected by watching /var/log/messages. Also the device is mentionned in /proc/bus/usb/devices. But when I do lsusb the device isn't showing up and it should be showing up! If it is not listed with lsusb, I can't connect to it through the k8055 executable...
View 1 Replies View RelatedWhat are the necessary packages for mounting NTFS partition on CentOS? i tried installing fuse-ntfs-3g but got a result saying its not available.
View 1 Replies View RelatedI have been using SLES 10 SP1 so far with about 6TB Raid system without problems.I have upgraded the OS to CentOS 5.3 i386 and I have noticed the kernel can not recognize raid system larger than 2TB.Is there any parameters that I have to set ? or the i386 distribution simply does not support larger raid, so I have to use x86_64 version, instead?
View 1 Replies View Related
