My board is not supported for U-boot. But it got an ARM920T core onboard running at 100MHz. It got a serial, JTAG and USB line. Can I custom port the U-boot for my board?
View 1 RepliesI am trying to load u-boot 1.1.6 in my samsung s3c6410 board. i am getting a error in this process,
s3c6410 # make clean
s3c6410 # make smdk6410_config
Above two command worked fine with out any error.
s3c6410 #make
executing the above command i am getting a lot of errors, such as
start.s:o: error:bad value (armv5t) for -march=switch
interrput.s:o: error:bad value (armv5t) for -march=switch
I am new to the porting, get me out of this problem
I have a virtual box running CentOS 5.3. I am experimenting with compiling and installing a kernel 2.6.33 on this.
However, the kernel compiled ok, but when I did the install it gave me these warning, not sure if they are important or not.
The steps I did was:
Code:
Code:
In my grub.conf I have the following:
Code:
When I try and boot I get the following problem:
Code:
I have an issue with my on-board wireless card (powers down after about 5 minutes) so I'm stuck with a USB card. I don't use the on-board card and it causes the system to intermittently hang if it's powered on (once I run ifconfig wlan0 down, the system runs fine). Is there a way to power down the interface (or better yet prevent it from powering on) at boot?
View 4 Replies View RelatedI try to make a small AVR-Board boot a Linux from my Lenovo laptop, which is configured as NFS server (running nfs-kernel-server). Everything is configured correctly and it should work, but it doesn't.I just installed another laptop (from ASUS) with the same configuration (OS, tools, settings) and there it works immediately.
So I wondered, what's going on on eth0 ? I checked with Wireshark and here are the things I found out.On both laptops, the following paket arrives:
[Code]...
I am trying to boot linux kernel 2.6.36.1. I have a alchemy db1200 board.It is an ECG machine. It is getting correctly booted using kernel 2.6.33.2 I have a feeling there is ethernet failure. I am getting stuck at the following stage:
Bytes transferred = 1960092 (1de89c hex)
lan9118: eth_halt
## Booting kernel from Legacy Image at 81000000 ...
[code]...
Is it possible to boot from my external hard drive when not supported? I have no room on my internal hard drive and I would like to install ubuntu on a section of my external hard drive. I have an old Dell Dimension 2350 and the BIOS does not support usb booting.
View 6 Replies View RelatedI'm trying to test out UEFI boot and install with Fedora 13. It looks like it is not supported...at least not in the standard x86-64 DVD image. Running 'dumpet' on the .iso shows no EFI boot section (whereas, for example, RHEL6 Beta-2 x86-64 DVD .iso does show one); see output below. Will there [ever] be UEFI supported boot/install CD/DVD .isos for Fedora?
[Code]...
How do I delete one of my posts?
View 6 Replies View Relatedi installed linux OS on my lpc3131 board with kernel 2.6.20. I want to install gcc to my board in order to compile codes without cross compiler or auxilary PCs. But i think it must be different then installing gcc rpm on Fedora PC or untar and make gcc, I dont know what i must do. what release or version of gcc should i download and what kind of changes must i do in Makefile.
View 5 Replies View RelatedBrand new to Linux. Just installed Debian 5.0.6 (64-bit). Upon booting up, the screen is all black with a gray floating screen that says "Input Not Supported". My guess is that the video card is not supported by Debian, but maybe somebody knows a way around this problem... (I know for a fact that both video card and LCD work fine in Windows XP.)
My hardware:
* Video card: ATI Radeo HD 4850
* LCD: Acer V193W
I'm searching for the cheapest single board computer which can run Linux. It must have ethernet and at least one serial port.I'm currently looking at these modules from Technologic Systems, but wondering if there's anything cheaper out there?
[URL]
I have found two ways to get the main board product name: [sudo lshw][sudo dmidecode] Is it the nature of this info that's making it protected or is it the source code of these tools?Is there any way to get main board product name without sudo? Shall I dig inside the source code of these tools?
View 2 Replies View RelatedI am trying to build a low cost computer, and over the last few days, I was interested in Linux as my OS to use. All I really need for the computer was the internet, word processors, and 3 games: "Wizard101", "Fusion Fall", and "Free Realms". Would Linux run on a built computer with an AMD processor and an on-board GPU? And would Linux run all of my needs/wants for this computer?
View 9 Replies View RelatedI have found two ways to get the main board product name:sudo lshw sudo dmidecode Is it the nature of this info that's making it protected or is it the source code of these tools? Is there any way to get main board product name without sudo?
View 5 Replies View RelatedOk now, whenever I try to boot up Ubuntu (I also have Windows 7 installed), this message pops up:
Code:
[ Minimal BASH-Like line editing is supported. For the first word, TAB lists possible command completions. Anywhere else TAB lists the possible completions of a
[code]....
I've been trying to use the onboard modem on my laptop for Internet connectivity. From what I can gather, Ubuntu hasn't installed a driver for the modem.
When I connect my phone using a usb cable to the laptop, I'm able to connect and browse. However, the network manager doesn't seem to have a driver for the onboard modem because it doesn't recognize it.
My friend has a HP Pavilion dv2699ea (dv2500 series - somehow *shrugs*) that has stopped working. It's a Core2Duo laptop with a Nvidia GPU. The unit is no longer under warranty. Problems first started a few days ago with the laptop showing corrupted graphics in Windows and BSOD'ing after a few minutes of use. I tried booting to an Ubuntu LiveCD which worked for a while before succuming and crashing as well. The freezing/graphics corruption/BSODing does seem somewhat heat related (CPU runs at ~95'c under load) however I believe that if it is heat related, then it's already damaged components inside.
Now the system has corrupted graphics on bootup[1], including booting Ubuntu[2], and neither operating systems will boot at all (Windows can sometimes get logged in before showing a black screen and becoming unresponsive. Ubuntu just looks like [3] after X starts). (See comment below for links.)
The fact the problem occurs both under Linux and Windows says to me this is not a driver issue. I have run Memtest which passed fine and none of this seems HDD related as I managed to get ~30GB of data off the system before it finally gave up the ghost.
She has been using it repeatedly without giving it adequate ventilation for years (i.e. on the bed, or on a pillow), so it's my opinion that the system board has probably warped over years of cooling/heating and that's causing this current problem. If that is the case, then I can buy a replacement system board and fit it myself, saving about £200 over the cost of an out-of-warranty HP repair. Of course, I don't want to make her spend £100 on a replacement part for it to be the wrong thing, hence asking for a second opinion here!
Hopefully I've covered all the bases here. I'm a former IT support guy myself, so I've tried all the dumb stuff (driver updates, examining memory dumps from BSODs [one 'unrecoverable hardware error', three relating to the graphics card], etc).
I'm trying to run a shell script on a kern board (av1100) that shows some text output on the attached screen. The big problem is that the screen goes to blank in like 2 minutes.I'd just like to have the script showing it's output while the thing is on.Isn't there a command to stop the screen from going to blank?p.s. there is no bash available, just #!/bin/sh
Code:
#!/bin/sh
###########################################################
[code]....
I have installed slacware 13 on an intel server, but the IP add that i have assigned does not work. I used ifconfig to check the ip but it shows me 127.0.0.1. I have run netconfig with the ip address i need and restart the machine, but it goes back to 127.0.0.1
View 2 Replies View RelatedSomeone told me that FC6 is outdated and no longer supported, So which version of linux should I choice?
View 2 Replies View Relatedi would like to know the list of browser's that fedora 12 supports (except firefox).i had installed opera 10.5 and it give me an error message kernel just crashed and restarts!i dont think so opera 10.5 is That stable with fedora, works properly in xp though.neways do tell me some browsers that can run smoothly in fedora
View 4 Replies View RelatedWhen I open gedit and also some other applications, I get this message:(gedit:29595): Gtk-WARNING **: Locale not supported by C library.Using the fallback 'C' locale.Why is this happening and should I worry about it? It does not seem to affect my subsequent work.
View 8 Replies View RelatedI'm trying to connect to a wep network. The password is very long and contains spaces. Someone wrote that this might be a solution: 'The key to gaining authentication against WEP is to see what hexi-string the router has on itself. I copied the string off my sister's, and now I use that string as my authentication, with the help of the iwconfig command.' What is the iwconfig command? And how exactly do you go on with this?
View 11 Replies View RelatedThe command and error message:
gtwy ~ # ip rule add from 64.251.23.186 table t1
RTNETLINK answers: Operation not supported
Older article of the same problem, but it did not help me: http://forums.gentoo.org/viewtopic-t-696982-start-0-postdays-0-postorder-asc-highlight-.html
I have looked on google at great lengths to try to find a solution. It seems that my kernel configuration is missing something? My system/kernel is: 2.6.36-gentoo-r5 #3 SMP Thu Jan 13 10:49:06 EST 2011 x86_64 Intel(R) Xeon(R) CPU X3220 @ 2.40GHz GenuineIntel GNU/Linux.I am posting this on SuperUser since this system is used as a workstation and this problem is unrelated to specific tasks that are handled exclusively by servers.iproute2 is installed:
gtwy etc # emerge --search iproute2
Searching...
[ Results for search key : iproute2 ]
[ Applications found : 1 ]
[code]...
I installed pyxattr to play around with, and when I try to set them it says that the operation is not supported. Does Arch Linux not support xattr, or how do I enable them?
View 10 Replies View RelatedIS SELinux fully supported by debian
View 1 Replies View Relatedjust wanna ask how many firewall chains are supported by kernel? and what are there..?
View 1 Replies View RelatedI am using RHEL5 - kernel version is 2.6.18-8.el5 and I want to purches a wireless lan card.
View 1 Replies View RelatedWhat printing protocols are supported by CUPS?
View 1 Replies View Related