Fedora :: Create 3TB Partition On Raid5 Device?

Jun 18, 2010

I have just bought 4 1TB drives and set up a Software Raid level 5. Using Disk Utility tool I have created a GPT partition table and now when I want to create a partition, I get:

Error creating partition: helper exited with exit code 1: In part_add_partition: device_file=/dev/md0, start=0, size=3000610848768, type=
Entering MS-DOS parser (offset=0, size=3000610848768)
MSDOS_MAGIC found
found partition type 0xee => protective MBR for GPT

[Code].....

it does say nothing about creating an partition on the /dev/md0, although Gnome Disk Utility allows to do that - if I just run mkfs.xsf /dev/md0 - it works fine, yet Disk Utility tells me that disk has not been partitioned, see image:

View 1 Replies


ADVERTISEMENT

Ubuntu Installation :: Cannot Create Partition: Device Or Resource Busy

May 11, 2010

When installing I am selecting the manual partitioning scheme( I have arch on another partition). After I have selected my custom partitions and their mount points it starts the installation but almost immediately it gives the error message that it cannot create a partition on the specified one, as it is used by the OS. I have also tried to create partitions through gparted in the live session but to no avail. I am sure that no partitions are mounted or in use by the system, I have checked this using the mount and fuser commands. I also tried the oem installation but the result the same.

View 3 Replies View Related

Ubuntu :: Raid5 And Static Device Names?

May 17, 2011

I am setting up a Raid5 and torture testing it. I added two eSata ports to my machine. When a drive is installed in that eSata port and the machine then booted up the device name (e.g. /dev/sdc) is inserted in the middle of my Raid devices. And that is just one example of how the device names can change.I did a search on 'static device names' but I saw nothing directly related to Raid. What I did see were suggestions to create udev rules based on UUID. But that was for single disks, not Raid, where each drive/partition in the raid array appears to have the same UUID.I'm surprised this does not come up in the various Raid howtos because it is impossible to keep a Raid array intact without solving this problem unless the machine is never touched thereafter.

View 1 Replies View Related

Ubuntu Servers :: Create A Raid5 With The Three New 1.5TB HD's?

Apr 15, 2010

Here is what I have and what I want to do.

3 new 1.5TB HD. 1 used 1.5TB hd with 980MB of data. I want to set up a raid 5 with a hot spare. I have music, pictures, videos, and movies (About 2.8TB worth). I have had a mismatch of drives previously, 250GB, 2 320GB, 500GB, 2 1TB and now a 1.5TB all with data. I have removed the one 250 and 2 320s and put the data on the 1.5TB that is currently installed.

What I would like to do is create a raid5 with the three new 1.5TB HD's, copy the data over from the currently installed 1.5TB and then grow or add that drive as a hot spare. Or just add it and then add another 1.5TB down the road as a hot spare don't know for sure.

In addition since I have 2 1 TB drives, I could add 2 more (Good deals on 1 TB drives right now) and have a total of 4 1TB drives. Could I have 2 raid5's (4-1TB's and 4-1.5TB's)in two separate arrays? I really do not know if that makes sense or not but here comes LVM. I am tired of managing my HD space and since i have multiple folders (Movies, music, pictures, videos) and within the movies folder I have R, G & PG folders for the ratings of the movies. (Pwd protect the R so the kids can't get to it) So with LVM installed with the Raid5 I should be able to create my folders and just keep adding data and not worry about moving folders around when I grow the storage by adding new drives. Is that correct? Maybe someone could point me to a how to.

Also, if I create 2 arrays (And I need to know so I can order the 2 additional 1TB drives), then I could put all the music, G and PG content on the one array and all the R and spicy stuff on the other and password protect it.

View 4 Replies View Related

Red Hat / Fedora :: Can't Properly Partition Both Hard Drives - Simple Way To Create Partition On Drive?

Jun 22, 2011

I installed Redhat Enterprise 3 on one of my servers. In my haste I didn't properly partition both Hard Drives and only properly partitioned one of them. Thus now I have

/dev/sdb1 478711768 137858256 316536328 31% /
/dev/sda1 101089 15346 80524 17% /boot

Where /dev/sda1 is actually a 80 GB hard drive. Is there anyway I can safely and easily repartition the unpartitioned space without causing a huge mess? I have a very important Oracle database on /dev/sdb1 and thus I want to be able to back it up on the second disk. I can create a partition on that drive?

View 2 Replies View Related

Fedora :: Home Partition And Create Logical Volume Out Of 53 Gb Filesystem Partition?

Aug 24, 2010

I installed fedora 13 64 bit and it works great but I encountered several issues when setting up guest OS with KVM. The problem seems to be related to selinux. But let me first ask question about logical volume. By Default fedora created logical volumes:

[Code].....

"If you expect that you or other users will store data on the system, create a separate partition for the /home directory within a volume group. With a separate /home partition, you may upgrade or reinstall Fedora without erasing user data files." seems to suggest I have to create a separate physical partition and assign that to /home. But reading elsewhere it seems to suggest logical volume acts like a partition. My goal is to make it easy in case fedora is hosed and I have to re-install it without affecting /home where my cirtical data resides. Given above do I need to create a separate physical partition or I am just fine?

I have a second hard disk that originally had windows and all my data. Windows is hosed but I can see my data from within Fedora and Windows is gone and I created created new partition in its place which used ot be the C:/ drive appears as 53 Gb filesystem. My data which was originally D drive appears as 215 GB filesystem. As given in [URL] I want to create a new logical volume in 53 Gb filesystem which I want to use as space for virtual disk to install guest OS's in KVM. Currrently 53 GB filesystem is mounted as /media/3467BH89JK789 but this does not work well with KVM. how do I create this logical volume out of 53 Gb filesystem partition and add proper selinux info and do I add to vg_vostrolx volume group and in a different volume group?

View 1 Replies View Related

Ubuntu Servers :: RAID5 Failed - MDADM (Device Or Resource Busy)

Feb 2, 2010

Something weird happened last night and my raid5 failed. I am trying to re activate it and see if my data is dead or what. When I run mdadm -Asv /dev/md0 I get

Code:
mdadm: looking for devices for /dev/md0
mdadm: cannot open device /dev/dm-1: Device or resource busy
mdadm: /dev/dm-1 has wrong uuid.
mdadm: cannot open device /dev/dm-0: Device or resource busy
mdadm: /dev/dm-0 has wrong uuid.
mdadm: cannot open device /dev/sde2: Device or resource busy
mdadm: /dev/sde2 has wrong uuid.
mdadm: cannot open device /dev/sde1: Device or resource busy
mdadm: /dev/sde1 has wrong uuid.
mdadm: cannot open device /dev/sde: Device or resource busy
mdadm: /dev/sde has wrong uuid.
mdadm: cannot open device /dev/sdd: Device or resource busy
mdadm: /dev/sdd has wrong uuid.
mdadm: cannot open device /dev/sdc: Device or resource busy
mdadm: /dev/sdc has wrong uuid.
mdadm: cannot open device /dev/sdb: Device or resource busy
mdadm: /dev/sdb has wrong uuid.
mdadm: cannot open device /dev/sda: Device or resource busy
mdadm: /dev/sda has wrong uuid.

View 4 Replies View Related

Red Hat / Fedora :: Create Logical Partition In Extended Partition Of 14?

Jun 13, 2011

I would like to create Logical partition in Extended partition using fdisk in Fedora 14 I created extended but fail to create logical partition.

View 6 Replies View Related

Fedora Servers :: Create TUN/TAP Device With Non Default Name?

Apr 27, 2010

I try to configure openvpn under Fedora, using TUN/TAP device. I configured it under windows without the problems. However in windows this device is TAP-WIN32 device with the name VPN-urs. It set set in client.ovpn file as:

Code:
# Windows needs the TAP-Win32 adapter name
# from the Network Connections panel
# if you have more than one. On XP SP2,
# you may need to disable the firewall

[Code]....

View 1 Replies View Related

Ubuntu Servers :: Raid5 Repair Partition Table - Recognized Too Late

Feb 27, 2011

I opened GParted to create a new partition on a new drive. He wanted me to create a partition table first which I did, and it was created directly without any prompt like im used to see when creating partition. So I recognized too late, that i actually created a MBR on one of my 6 1TB raid5 drives. Not beeing sure if the ne MBR was really written, I have opened ubuntu disk utility and clicked on the check raid button. It directly made a resync. After the resync, mdadm --detail /dev/md0 told me everything is ok and synced. Then I wanted to mount it with:

mount /dev/md0 /mnt Then I get the following error: "mount: wrong fs type, bad option, bad superblock on /dev/md0, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so" I think I just killed my raid5 ;(

I shouldnt work on my server when im tired and when I actually have no time ;( My last hope is the fact, that "Disk Utility" shows that there is a .0 TB ext4 volume on my raid (see screen below) [URL]

View 5 Replies View Related

Fedora :: How To Create RAW Disk Device In Fedora 12?

Mar 4, 2010

I got this information of creating raw devices and then starting the service service rawdevices start.But there appears to be no service 'rawdevices'. Please can anyone help me with this?Is there anyway I can create an disk /dev/sda7 and then link it as a raw device?

View 5 Replies View Related

Software :: My Software RAID5 Is Saying No Space Left On Device When It's Not Full

Dec 25, 2010

I have had a software raid running on OpenSuse / SUSE 10 & 11 for some time and I have about 8TB on it. I always run close to 100% and once in a while get there but always manage to delete a bunch and clear out about 30-100GB.

View 3 Replies View Related

Fedora :: Create New Home Partition

Oct 9, 2009

I'm currently using fedora 11 and going to upgrade to fedora 12 and I want to seperate my home partition from root partition. Fedora 11 is on extended partition.

View 1 Replies View Related

General :: Create New Partition On HDD (OS Fedora 11)?

Feb 4, 2010

I would like to create a new partition to install Solaris OS. My current partition table is below:

Device Boot Start End Blocks Id System
/dev/sda1 * 1 27 204088+ 83 Linux
/dev/sda2 28 20667 156038400 8e Linux LVM

[code].....

View 3 Replies View Related

Fedora Installation :: How To Create Swap Partition?

May 31, 2009

On numerous installs I ignored "swap" message but want to create one this time. And can it be done post installation?

View 5 Replies View Related

Fedora :: Create A New Partition In Unused LVM Space

Jan 10, 2010

I just installed Fedora 12 in a laptop with a big hard drive and used LVM for it. The thing is that I used just a fraction of the LVM total size to create the "/" partition and decided to leave the task of creating the other partition (the data partition) with the rest of the LVM space after F12 got installed. Unfortunately I found that Gparted is apparently unable to perform that task of creating a new partition in unallocated LVM space. Is there any way I can create a new partititon in that unused LVM space?

View 4 Replies View Related

Fedora Installation :: Error Creating Partition - Device Or Resource Busy

Jul 19, 2011

So I cant seem to be able to install fedora 15. I think it is the disk. I have windows 7 already installed (and would like to keep it) It was installed on the end of the hard drive leaving a 100 GB chunk in the center of the drive open and unformatted (this may be the problem). Anyway I used the live cd and tried to format the unformatted partition to exf but it gives me this error

Code:
Error creating partition: helper exited with exit code 1: In part_add_partition: device_file=/dev/sda, start=105906176, size=104752742400, type=EBD0A0A2-B9E5-4433-87C0-68B6B72699C7
Entering MS-DOS parser (offset=0, size=500107862016)
MSDOS_MAGIC found
found partition type 0xee => protective MBR for GPT
Exiting MS-DOS parser
Entering EFI GPT parser
GPT magic found
partition_entry_lba=2
num_entries=128
size_of_entry=128
Leaving EFI GPT parser
EFI GPT partition table detected
containing partition table scheme = 3
got it
got disk
new partition
added partition start=105905664 size=512
committed to disk
Error doing BLKPG ioctl with BLKPG_ADD_PARTITION for partition 2 of size 105905664 at offset 512 on /dev/sda: Device or resource busy

Do I have to reinstall windows for this to work or is there something I can try to do.

View 2 Replies View Related

Fedora Installation :: How Many Logical Mounts Or Partition To Create

Feb 16, 2009

just about to install Fedora 10 on my MSI WIND laptop and read abit about file system on Linux and come across alot of recommendations on how many logical mounts or partition to create..so far i have created /boot of 100MB.i'm unsure of what sizes i will give to my [root] / and /home and /swap

i am thinking of assigning 1GB to /swap which leaves me with 40GB left for / and /home.i'm going to install alot of softwares and probably try out wine as well.i want a separate /home directory incase i change distro then i'll keep it... where does the programs go to under?

View 4 Replies View Related

Server :: Recreate A Raid5 MD0 Into A Raid5 MD3?

Jan 9, 2010

I have no drive failures but just need to recreate a raid5 set as the next free MD disk number. Originally I built a temp OS of debian on a single drive and had 4x2TB drives in a raid5 software array (MD0) this worked fine and allowed me to move all data to it, and remove our old fileserver. I have now pulled out the 4 x 2TB Raid 5 drives and created a new OS on two new 80GB drives, partioned as follows,

MD0 is now 250mb Raid1 as /boot
MD1 is 4GB Raid1 Swap
MD2 is 76GB Raid1 as /

If I turn off and push back in the 4x2TB drives I cannot see a MD3. I presume I would need to create a MD3 from these 4 drives but I dont want to mess things up as its live data. So im here asking for help, or a bit of hand holding to get it done right.

PS - Its a Debian Lenny 5.0.3 Raid1 fresh install replacing a Debian Lenny 5.0.3 on a single disk.

View 2 Replies View Related

Fedora Installation :: F12 Partitioning - Create A Custom Partition Layout?

Nov 29, 2009

I have several partitions on my hard drive, and like to use the 'Create Custom Layout' option during the installation process, to make sure that I don't loose any of my existing partitions or the data on them.

I have attempted a minimal F12 installation from Fedora 12 DVD. But the 'Create Custom Layout' option is not an option in the menu.

How do I install F12 and tell anaconda exactly which partitions I want to use and format?

My current working partition layout is shown in the attached screenshot.

I want to use the following custom partition layout during the initial F12 installation:

Code:
/dev/sda2 / Fedora-12-root
/dev/sda3 SWAP
/dev/sda11 /var/log/ var-log
/dev/sda12 /tmp tmp

This allows me to share existing partitions between my current working F10 root partition, and the newly-installed F12 root partition. So if there are problems with the new F12 installation, I still have a working F10 system to fall back on.

The other partitions with data on will be mounted when the intiall installation has been completed

View 4 Replies View Related

Fedora Installation :: Unable To Create Partition - Not Enough Free Space

May 17, 2010

I just downloaded the new fedora and proceed to install it into a free space of 11GB on my HDD. As such the partitioner is unable to create more than 1 partitioneven if free space is available, it reports not enough free space seen if its present. As such it can create only one of the three partitions i.e., swap or / or /home duw to which cannot proceed ahead.' Some more details me running Xp as the other OS on my system.

View 10 Replies View Related

Fedora Installation :: Create 6GB /user Partition And It Says Not Enough Disk Space?

Oct 4, 2010

I have a 80GB HDD on which I have installed Ubuntu10.04. I have about 45GB space remaining. I am trying to install Fedora13. I create : 2GB / partition - 2.4GB swap partition. I want to create 6GB /usr partition and it says not enough disk space? Why is it giving that message?

View 1 Replies View Related

Fedora Installation :: Partition Deletion - Create Custom Layout

Aug 17, 2011

I am trying to install fedora15, my devices are as follows:
/dev/sda1- contains windows recovery
/dev/sda2- contains windows vista
/dev/sda3- free space
/dev/sda4- where fedora10 is existing.

Basically I want to scrap the fedora 10 in /dev/sda4 and install fed15 on the place (ext3). During the installation process fedora asked me, Which type of installation you want? I choose 'create custom layout'.

Then in the next window that appeared I choose /dev/sda4. Then it gives me four options like
Create Edit Delete Reset

I want to know what does this Delete mean. What will it do, will is erase all the older partitions within /dev/sda4 i made for fedora10 (previously I made three partitions /boot, swap, /) or will erase /dev/sda4 itself. I am scared to continue installation further.

View 10 Replies View Related

Ubuntu Installation :: Create New Partition Table Does Automatically Create New Mbr

Oct 28, 2010

When using the gparted option to create a new partition table does this automatically create a new mbr?

View 1 Replies View Related

Fedora :: Resizing Partition To Create Another File System On Free Space?

Dec 7, 2009

I have decided that my partition table does not meet my needs Barrymore, and I want to shrink the "/" partition by 80GB, and then create another file system on that space. I did some research on-line, and I'm not sure which way is the easiest and more secure way to perform the change with out putting the "/" file system on risk.

View 1 Replies View Related

General :: Convert Full-disk RAID5 Array To Partition-based Array?

Dec 23, 2010

I have a RAID 5 array, md0, with three full-disk (non-partitioned) members, sdb, sdc, and sdd. My computer will hang during the AHCI BIOS if AHCI is enabled instead of IDE, if these drives are plugged in. I believe it may be because I'm using the whole disk, and the AHCI BIOS expects an MBR to be on the drive (I don't know why it would care).

Is there a way to convert the array to use members sdb1, sdc1 and sdd1, partitioned MBR with 0xFD RAID partitions?

View 1 Replies View Related

Server :: Reduce RAID5 Partition Sizes / Reduce The Size Of Md1 And Grow Md0?

Feb 14, 2010

I have a rack of four 1TB drives all partitioned identically with three primary partitions. On each drive

- the first partition is only 64MB;
- the second is a large 900GB partition and
- the last holds all the remaining space

mdadm has been used to set up
/dev/md0 - RAID1, comprised of /dev/sda1 and /dev/sdb1
/dev/md1 - RAID5, comprised of /dev/sda2, /dev/sdb2, /dev/sdc2, /dev/sdd2
/dev/md2 - RAID5, comprised of /dev/sda3, /dev/sdb3, /dev/sdc3, /dev/sdd3

OK, so it was a silly mistake to make - but I am now need to increase the size of /dev/md0. My thinking is to reduce the size of md1 so that I can grow md0.

On md1 I have two logical volumes. I've successfully reduced the size of the volume so that I can reduce the size of md1. Now I'm at the nervous stage; I can find little written on the topic of shrinking RAID5 arrays - and even if I do this I'm unsure if I can move partitions around to regain the space I so desire.

View 1 Replies View Related

Fedora Installation :: Fc11 - Preview Installer Crashes After Attempt To Create A Partition

Oct 2, 2009

when i try to install fedora 11 on my laptop my Fedora 11 Preview installer crashes after attempt to create a partition. How do i overcome this problem

View 6 Replies View Related

Fedora Hardware :: Trying To Mount Drive - Create An Ext4 Partition To Move The Data

Jun 12, 2010

I just installed F13 x86_64 on a system that used to be running Windows 7.

The boot drive is a SATA drive attached to the motherboard which is working fine.

However, my data drive is an NTFS partition filling a 3.6TB SATA raid.

It's GPT--Gparted sees 3 unknown partitions, and gdisk shows:

Code:

How do I mount this in Fedora 13? I had intended to shrink the NTFS partition so that I can create an ext4 partition to move the data to. Will this be possible?

I've got a LOT of valuable data on this drive, and nothing else big enough to store it.

View 3 Replies View Related

Ubuntu Servers :: Convert Mdadm 6 Disk Raid5 To 5 Disk Raid5?

Jun 30, 2011

I know you can fail and then remove a drive from a RAID5 array. This leaves the array in a degraded state.

How can you remove a drive and convert the array to just a regular, clean array?

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved