Fedora Networking :: Wireless Card RNX-N250PC (chip Rt3562) 64bit?

Jul 17, 2011

Just a short note on getting this card to work in Fedora 14 (and presumably Fedora 15) 64bit. First of all, none of the rpm packages which you might choose will work because none of them are for this chipset. First, one goes to the Rosewill website, finds the driver for this card as a compressed tar file. After downloading it and extracting, you will find in the parent directory a Makefile and README_STA_PRI.

The instructions in README_STA_PRI, if followed carefully, will do the job except for one thing: there is a mistake in the os/linux/config.mk file that needs to be fixed. In the $(PLATFORM),PC 2.4 branch, change -imarch=i686 to -march=core2 and more importantly, in the 2.6 branch, add -march=core2 to the EXTRA_CFLAGS and add export CFLAGS (which would otherwise not be done). In the main Makefile, as per the instructions, I set HAS_WPA_SUPPLICANT=y and HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=y so that the Network Manager can control the card.

In the instructions, wps_supplicant is not where they indicate (it is in /usr/sbin/) and the configuration file which I used was in /etc/wpa_supplicant/wpa_supplicant.conf, not the one in the dbus-1/system directory. The wpa_supplicant command was run before the make and before "insmod rt3562.ko", and it generated a bunch of error messages because the card had not be recognized yet. The error messages didn't seem to matter.

The card was already in the machine and when "insmod rt3562.ko" was executed, the card was instantly recognized and the network manager set it up and put it into play without any further fuss or muss.

View 1 Replies


ADVERTISEMENT

Ubuntu Networking :: 10.10 RNX-N250PC Ralink Chip RT3062 Driver Install

Nov 3, 2010

I'm trying to get a Rosewill RNX-N250PC wireless card w/ ralink rt3062 chip to work in a new build. I am able to see the card in Device Manager, but can't get the driver to work despite trying many of the suggestions I've read elsewhere. I installed build-essentials and downloaded the driver from ralink. I unzipped the folder, and started to follow README as well as this thread rt3062 [URL]. So, I've adjusted MODE and TARGET as instructed in Makefile. I also adjusted the following sections of red text from Makefile:

ifeq ($(PLATFORM),PC)
# Linux 2.6
LINUX_SRC = /lib/modules/$(2.6.35-22-generic)/build
# Linux 2.4 Change to your local setting
#LINUX_SRC = /usr/src/linux-2.4
LINUX_SRC_MODULE = /lib/modules/$(2.6.35-22-generic)/kernel/drivers/net/wireless/
CROSS_COMPILE =
endif

Then I set HAS_WPA_SUPPLICANT=y and HAS_NATIVE_WPA_SUPPLICANT_SUPPORT=y in /os/linux/config.mk in the driver folder.
Then I code: $ make (also tried sudo make with same result)
and get:
make -C tools
make[1]: Entering directory `/home/das/2010_07_16_RT3062_Linux_STA_v2.4.0.0/tools'
gcc -g bin2h.c -o bin2h
make[1]: Leaving directory `/home/das/2010_07_16_RT3062_Linux_STA_v2.4.0.0/tools'
/home/das/2010_07_16_RT3062_Linux_STA_v2.4.0.0/tools/bin2h
cp -f os/linux/Makefile.6 /home/das/2010_07_16_RT3062_Linux_STA_v2.4.0.0/os/linux/Makefile
make -C /lib/modules//build SUBDIRS=/home/das/2010_07_16_RT3062_Linux_STA_v2.4.0.0/os/linux modules
make: *** /lib/modules//build: No such file or directory. Stop.
make: *** [LINUX] Error 2
das@desktop:~/2010_07_16_RT3062_Linux_STA_v2.4.0.0$

View 9 Replies View Related

Ubuntu Networking :: Azio AWD102N Wireless Card-rt3562 Driver Install Woes?

Jul 17, 2011

i recently purchased a new custom-built computer and thought i would give ubuntu a shot (read: i'm a linux noob). i'm running 11.04. anyway, i can't get my pci wireless card to work. i downloaded the rt3562 driver from ralink's site, followed the directions in this tutorial url?t=1608095 and i keep getting an error message when i try to do "sudo make":

Code:
make -C tools
make[1]: Entering directory `/home/brock/DPO_RT3562_3592_3062_LinuxSTA_V2.4.1.1_20101217 2/tools'
gcc -g bin2h.c -o bin2h
code....

View 3 Replies View Related

Fedora Networking :: No Wireless On Broadcom Chip & No Access To Wired?

Aug 25, 2011

This is my first time here and I'm very much a beginner to Linux. I installed Fedora 14 and found out I didn't have wireless. I found this beautiful guide online posted by Stoat:

[URL]

but unfortunately, I live in an apartment and can only get access to wireless internet. I hope I'm posting in the correct place. Anyways, this is my setup:

$ uname -r
2.6.35.14-95.fc14.x86_64
$lspci
Network Controller: Broadcom Corporation BCM43225 802.11b/g/n

View 2 Replies View Related

Ubuntu Networking :: Mini PCI Wireless Card Compatible With 64bit?

May 9, 2010

I have a Samsung N310 with a atheros wireless card. Been having trouble getting it to work. I was thinking about upgrading to a N card anyway so I will be buying one tonight. Does anyone know of a Mini PCI N card that works out of the box with ubuntu 64bit?

View 1 Replies View Related

Fedora X86/64bit :: 15 Dont Recongnize Broadcom BCM 4322 Wireless Card?

Aug 6, 2011

I am a newbie in rpm files, I am testing Fedora 15 (gnome3),nd I liked it, congratulations to Fedora Team, I was using Linux mint9, and I have a certainly experience with .deb files and APT, but .rpm and YUM, I am a little lost...I have a HP Pavilion dv2-1110us laptop with a Broadcom BCM 4322 wireless card; the netwokmannager said "wireless firmware missing"How can I install it?There is in the Fedora repositories?

View 5 Replies View Related

Ubuntu Networking :: Kubuntu 4.10 - Installing PCI Wireless Mymax MWA/PCI-150N (Chip RT3060F)?

Aug 19, 2011

Good afternoon, I have a PC with Kubuntu 10.04 and a PCI Wireless Mymax MWA/PCI-150N RT3060F chip, I am not able to install, configure the system, I downloaded the driver on the site [URL]... php? s = 2, RT3062PCI/mPCI/CB/PCIe (RT3060/RT3062/RT3562/RT3592) and follow the procedures but it still fails, the card comes up in the connections but no signal scans.

View 9 Replies View Related

Fedora Networking :: 14 Can't Connect To SpeedTouch 585 - Either Wireless Broadcom Card Or The Wired Ethernet Card

Dec 4, 2010

Just installed Fedora 14 from the Live CD i686 on my Dell Inspiron 1521. I can't connect to the SpeedTouch 585 on either wireless broadcom card or the wired Ethernet card.

I can connect to it from the same Laptop on the Vista which is on dual boot on the same laptop.

Further confusing is that I ran Fedora 14 and connected to another SpeedTouch today.

Already checked the Channel on the wireless nic and it's on the same one as the SpeedTouch.

View 6 Replies View Related

Fedora Networking :: Not Seeing The Wireless Card?

Apr 15, 2010

I have a Toshiba Satellite L455D-S5976. Brand new. I made a partition and made it dual boot with windows seven and fedora with the newest version from the site. It won't recognize the wireless card. I'm assuming it needs drivers but I don't know where to find drivers so it will recognize.

The wireless does work on the windows side so I know it's not a problem with the wireless card.

View 6 Replies View Related

Fedora Networking :: How To Enable The Wireless Card

Mar 3, 2010

I just loaded the boot-able cd, and I do not have enough knowledge with Linux bases OS's to figure out how to enable the wireless card. ifconfig produces an eth0 and a lo, when I try ifup wlan0, it says: configuration for wlan0 not found. I have looked at all the forums notes and cannot find anything that seams like it is the same problem.

View 12 Replies View Related

Fedora Networking :: Usb Wireless Card Not Activating ?

Aug 27, 2011

I am trying to get a netgear wireless usb card to work correctly. I have installed ndiswrapper and gotten the correct drivers installed. The device does show up with lsusb. I can't seem to figure out how to get the wireless card to show up in gnome to start using it.

Update: the ndiswrapper module does load but when i run ndiswrapper -l it just shows the driver installed but, it is not showing my wireless usb card (0846:9020).

View 6 Replies View Related

Fedora Networking :: Install Netgear WN111v2 (AR9100ap Chip) On 12 Web Server

Apr 17, 2010

I am having some difficulties installing a wireless usb adapter on Fedora 12. the usb adapter is: Netgear WN111v2 Wireless-N USB adapter and it has the chipset: Atheros AR9100AP. I did a intensive search on the web but i don't know how to go further. These are the steps i've tried. I installed NdisWrapper and tried the following:

[code]...

But i really have no clue what to do further. I also found this site, which seems to have all the answers: [URL]... But i have no idea how it works. I copied all the firmware files to right directory. But what is the next step?

View 1 Replies View Related

Fedora Networking :: Access Wireless Internet - Air Card On 10?

May 8, 2009

I am building a CarPC which I'd like to have wireless internet access on. I have Verizon phone service so if there is a Verizon air card (not wireless card, an air card so I can have constant access without having to search for hot spots) that would work with Fedora 10 I would be very happy. I don't really know where to start and I can't find too much on Google, so I'm just looking for what options are available.

View 3 Replies View Related

Fedora Networking :: TPLink Wireless Lan Card And FC10

Aug 1, 2009

How can i run internet in FC 10(KDE). I have wireless lan card in my pc.

TPLink TL WN353G.

View 1 Replies View Related

Fedora Networking :: Install Broadcom Wireless Card On 11?

Sep 1, 2009

I chose to change my operating system from Microsoft Xp to Linux and finally chose Fedora to be my new OS.

After Fedora installation I got a problem that I cannot connect to my wireless network I used to using Xp, I think that my wireless card is not installed on Fedora because when I checked in the network configuration I found that the only installed adapter is the Ethernet Realtek for the wired connection.

My OS is Fedora 11.

The CPU Model name is : Intel (R) Core (TM) 2 Duo CPU T8300 @2.40 GHz, so I think that my architecture is x86_64.

My Network controller is : Broadcom Corporation BCM4312 802.11b/g

View 14 Replies View Related

Fedora Networking :: Wireless Card Stopped Working?

Jan 9, 2010

I have a relatively new F12 install (one week old) on which I got my wireless Broadcom card working using kmod-wl-PAE. It was a very easy process - not really a process just yum install kmod-wl-PAE.

After a few updates, I notice that the wireless card stopped working. I assumed maybe there was an update that conflicted, so I did a reinstall of kmod-wl-PAE and it worked again immediately.

Then I started installing compiz-fusion. Immediately after, wireless is broken again. So I yum erase kmod-wl-PAE and then yum install kmod-wl-PAE and it works again.

Now, only slightly later that same day, wireless stops working more or less randomly and I cannot get the reinstall of kmod-wl-PAE to fix it. So I uninstall, disable compiz-fusion, shut down, and restart the computer to try again. My thought is that maybe along the way my autostart compiz or something about compiz is causing the wireless not to configure properly. When I restart, wireless is working. Without kmod-wl-PAE installed:

yum info kmod-wl-PaE
Loaded plugins: presto, refresh-packagekit
Available Packages
Name : kmod-wl-PAE
Arch : i686

[Code].....

One, how is this even possible, and two, what is going on with the wireless working, not working, working, not working?

View 14 Replies View Related

Fedora Networking :: Unable To Use Wireless In 12 With Card Realter8172

Mar 28, 2010

I have for 2 months Toshiba Satellite A 500-18Q (Core Duo, Windows7 pre-installed). I have just wifi internet in my home, with Windows7 it works perfectly and automatic. However, my fresh- installed Fedora12 cannot see any wifi at all. I my NetworkManager I can see a single line with "eth0" which seems to refer to a normal (cable) connection. How to activate wifi? Just add a new line with eth1 and Wireless connection? Or I need to install some drivers?

this is output from my terminal:

# lspci
01:00.1 Audio device: nVidia Corporation Device 0be2 (rev a1)
0e:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)

[code].....

View 2 Replies View Related

Fedora Networking :: Cannot Get BCM4312 Wireless Card Working

Apr 9, 2010

I recently purchased an Acer eMachines E525 laptop, and currently have it dual booting Windows 7 and Fedora 12 x86_64 with the 2.6.31.5-127 kernel. I've been completely unable to get the wireless card working in Fedora (it works fine in windows).

lspci lists the following about the wireless card:
Code:
Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01)
so I assume it's a BCM4312.

So far I have tried downloading the driver from [URL] and then trying to install it according to the accompanying readme file: [URL]. However, when I try to make the driver, I get the following message:

Code:
KBUILD_NOPEDANTIC=1 make -C /lib/modules/`uname -r`/build M=`pwd`
make: *** /lib/modules/2.6.32.10-90.fc12.x86_64/build: No such file or directory. Stop.
The Readme says that if I get this kind of error, I need to install the "kernel-devel" package, but I have this installed and it still returns the same error.

I have also tried following the fw-cutter instructions for fedora from [URL], but it still doesn't work. I realise there's the option of using ndiswrapper, but I gave that a shot with Fedora 11 on the same machine and had no luck, and I'd really like to see whether any of the other options work before going down that route.

View 6 Replies View Related

Fedora Networking :: Unable To Find Wireless Card

Jun 16, 2010

I have been running F13 since it came out, with the wireless working fine since I got it working (using the RPM Fusion repository, broadcom-wl-5.60.48.36-1.fc13). Since I updated software (without reading what was to be updated), yesterday, I am unable to even find wireless networks, although I am, as you can see, able to access through eth0 It is not a hardware problem, as I can not only find them, but access them on Ubuntu 9.10 live disc. Below is my lspci

00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)

[code].....

View 1 Replies View Related

Fedora Networking :: F10 And Trendnet Wireless Network Card

Sep 8, 2010

I know that most people are using F12 and F13 but I just installed F10 on one of my machines. The Kernel is 2.6.27.5-117.fc10.i686 and the GUI is Gnome 2.24.1.I have a Trendnet wireless card already installed in the machine from when it ran XP which is in the tew-421pc/tew-423pi family. Is there a device manager/hardware installer that I can use to set up the wireless card or does anyone know of a driver install program for this card?

View 1 Replies View Related

Fedora Networking :: USB Wireless Card Ok In Gnome But Fail In KDE

Nov 24, 2010

I connected to internet via a USB wireless card, it works OK in GNOME, but it can't be detected on KDE. When enter KDE, iwconfig can not find any wlan. Wireless network connection not configured caused no wireless AP available, so the network not available. After I configured the wireless connection, The problem fixed. I'm replying in KDE now.

View 1 Replies View Related

Networking :: Unable To Use Atheros Wireless Card On Fedora 14

Nov 7, 2010

This morning I installed Fedora 14 on my laptop. During the setup, I was able to configure the wireless connection and use it to install additional software from the FreshRPMs and Livna repos. When the install was completed, I was surprised to find the wireless not working. When I click on the NetworkManager icon at the bottom right corner, I see "Wireless Networks" Under that it says "device not ready" and it is greyed out so it cannot be click on.

Running lspci -vnn returned
07:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR5001 Wireless Network Adapter [168c:001c] (rev 01)
Kernel driver in use: ath5k
Kernel modules: ath5k

View 3 Replies View Related

Fedora Networking :: Setting Up Linksys WMP54G Wireless Card

Jun 18, 2009

I just installed Fedora again, after a long absence. I have been using XP. I am having issues setting up my wireless card Linksys WMP54G. For some reason the card has been recognized, and the interface is there. But I have tried every walk-trough known to Google, and it still won't work. I have been using the GUI tools, but they don't work. I have also been using the command line walk through, and they aren't working either. Does anyone know which files I need to set and what the process would be?

View 3 Replies View Related

Fedora Networking :: Wireless PC Card Not Connected To Any Network - Driver

Dec 22, 2009

I have a Netgear WG511GE PCMCIA card, and a driver from the original installation disk. I used an ndiswrapper-utils gui called ndisgtk to install the driver. I then do the following to verify an installation:

[Code]....

Unfortunately, when I put the PCMCIA card in, nothing happens. On Windows, a green light flashes even if the card is not connected to any network. At first I thought this might be a hardware issue, so I did #lspci and got:

[Code]....

Lo and behold, when I put a different unbranded Wireless PC Card in it works. I'm no expert in Networks, but to me this suggests a driver problem (i.e. the card is physically detected it just won't work). However, the correct driver was installed with ndisgtk and this was verified with #ndiswrapper -l, hence the confusion.

I'd be grateful if anyone else has had this problem/knows of this problem and is willing to share the solution with me/point me in the right direction. So far, Google has returned a few posts from a few years ago talking about patching kernels and manually building files etc (just before Prism54 became integrated into the Linux kernel).

View 8 Replies View Related

Fedora Networking :: Unable To Use Dell 1395 Wireless Card On 11?

May 13, 2010

I am trying to get the Dell 1395 (Broadcom) wireless card to work on my PC and having a nightmare. I am certain the bulk of the reason is my inexperience with Linux but all the same it is causing me no end of problems.I have found the following sites which suggest ways to get it working

[URL]

Unfortunately I can't get either method to work on my Fedora 11 installation. I don't mean that I complete the steps only to find it doesn't work, I mean I can't even complete the required steps because I appear to be doing something wrong or be missing a crucial command tool.When I try to run the broadcom method I get as far as the make (or make clean) commands.

The make clean results in:

Code:

KBUILD_NOPEDANTIC=1 make -C /lib/modules/`uname -r`/build M=`pwd` clean
make[1]: gcc: Command not found
make[1]: Entering directory `/usr/src/kernels/2.6.30.10-105.2.23.fc11.i586'

[code]..

If I try the other method I get into problems when I get to the ndiswrapper section as the install can't find ndiswrapper-common.

View 6 Replies View Related

Fedora Networking :: Wireless Card Not Detected - Drivers Not Installed

Jan 13, 2011

I have installed Fedora 14 on my new laptop Thinkpad T410 but the wireless card is not detected.
I tried to install the drivers but got error. How to install the driver.

[root@sheril sheril]# lspci
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02)
00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02)
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02)
00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) .....

View 1 Replies View Related

Fedora Networking :: Wireless Network Card Being Detected But Not Being Allowed To Activate?

Mar 7, 2009

I have downloaded and installed Fedora 10.Now I am setting up the network and in the 'network configuration' it finds the wireless device (ralink) in the 'hardware' section of the configuration - I set this to eth0 (it originally set itself to wan0 and I still had the same problems, now it doesn't give me the option to put it back to wan0).Now I goto the devices tab and try to set up the device with eth0 - which it seems to find.But when I goto activate the device it tells me that eth0 cannot be found

View 2 Replies View Related

Fedora Networking :: 12 On Dell Inspiron 1545 And No Wireless / Activate The Card?

Jan 15, 2010

I have install 64bit version of Fedora 12 on a new Dell Inspiron 1545 with a Dell 1397 wireless card. It actually uses a Broadcom BCM4312 chip.

I have install the following rpms:

Code:
broadcom-wl-5.10.91.9.3-1.fc12.noarch
kmod-wl-2.6.31.9-174.fc12.x86_64-5.10.91.9.3-3.fc12.11.x86_64
kmod-wl-5.10.91.9.3-3.fc12.11.x86_64
code....

what I do not understand is the state of the card as unavailable. how I can activate this card?

View 2 Replies View Related

Fedora Networking :: Unable To Activate Wireless Card In Security Spin

Jul 27, 2010

I've been trying to get Security Spin up and running (after having tried unsuccessfully with knoppix STD). I need to be able to connect to my home network, or hell any wireless network.I've tried using iwconfig wlan0 as well as the options in the Network Configuration panel as well as other related panels. I'm able to change and set up profiles for the wireless card, but not to activate them. The button just isn't clickable.If it helps, I'm running Security Spin from a unetbootin usb drive. The wireless card is identified by the system as "Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection" .

View 2 Replies View Related

Fedora Networking :: Wireless Card Edimax EW-7711In Doesn't Work

Sep 7, 2011

I installed Fedora 15 64 bits version on my desktop, and I'm having hardtime activating my wireless card.

I tried following the instructions from this thread without success [url]

Here are the logs of some of the commands I used

lspci output

Code:

iwcconfig

Code:

Code:

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved