Fedora Installation :: VirtualBox 13 Guest: Live CD Installation Failure
Aug 3, 2010
Running VirtualBox 3.2.6 under some host OS (should be irrelevant which one, right?), I created a machine, intending to install Fedora 13 on it. Got the Fedora 13 Live CD iso image, and an 8.6 GB virtual hard drive, completely blank. I set the machine to boot off the Live CD image. The Live CD boots nicely and I get to its desktop. I open "Install to Hard Drive"...and nothing happens. No error message, zip, nada. Inspection of the system shows a series of odd file systems, but I have no clue what they are for and whether they're usable or not.
The sticky [URL] mentions that the blank virtual hard disk should be partitioned and formatted beforehand...So I did, using the Live CD's Disk Utility (Applications: System Tools: Disk Utility). Although the sticky states the small /boot partition should be ext2 or ext3, the Live CD installer proposes to reformat it as ext4. Shouldn't we have formatted it as ext4 right away, then? Also, the installer set the /boot partition's size to 524 MB, not 200 MB as recommended by the sticky.
OBSERVATION: This was not easy because VirtualBox sets the display to 800x600 at most, and the Disk Utility spills beyond those confines WITHOUT PROVIDING SLIDERS. It was sheer luck that the required buttons (create partition, format partition) were barely reachable (at the bottom edge of the screen). This is a serious problem, because increasing the VirtualBox display size can only be done *after* installation (see for instance[URL] - since this guest addition requires rebooting the guest OS, it probably won't stick to the Live CD).
Once those two partitions are prepared and the virtual machine rebooted, "Install to Hard Drive" works as expected.
OBSERVATION: It is absolutely inexcusable that the Live CD installer (Anaconda?) does not propose to do this partitioning and formatting for the user. It is even more inexcusable that it should fail without giving any feedback whatsoever to the user.
Aside: VirtualBox's guest additions does not work correctly (for 3.2.6 anyway). The Devices: Install Guest Additions menu merely mounts a CD image VBOXADDITIONS_3.2.6_63112) without any feedback (expected feedback because the menu ends with an ellipsis). The CD, once opened, has an Open Autorun Prompt button...which fails to do anything. Manually running autorun.sh also fails. I had to manually invoke VBoxLinuxAdditions-x86.run from a terminal to get anywhere. Even then I was unable to go higher than 1024x768.
I have tried a few times already the following procedures: start a new installation (each time, I create a new VBox VM) with the Fedora 12 DVD iso attached to the DVD drive of the VM. I select the default setting, like US english, US keyboard, local time (GMT +8), standard installation ... etc). The installation process had been smooth to the screen the system asking for a reboot after installing something like 1100+ packages. Then I click the reboot button offered. The VM restarted but each and every time, it came up with the following error message:
Booting from local disk... FATAL: INT18: BOOT FAILURE
There was no other error message durint the installation process. It would be very much appreciated if some one can tell me what went wrong and how to solve it. I believe even I try again the same way, it will end up with same result. Is it a software or hardware problem? In case software problem, is it Fedora or VirtualBox?
I've run the install to hard drive program three times over and each time I get "disk boot failure". I believe I've got Grub to install to the mbr but I am not sure.
System: Barton 3200+ with 1GB of DDR1 Asus A7V333 High Point hard disk controller
other items
All the hard drives are hooked to the High Point controller. It recognizes all of them that have power hooked up and read/writes to them. Two have 98SE installs, the third is where I'm trying to install Fedora 12 to get away from some problems I'm having with 98SE.
The BIOS is set up to boot from the "SCSI device" which means it's booting from the High Point controller. The High Point lets me set a boot mark, which, when set to the Fedora drive, yields the disk boot failure no matter what I do to it.
I installed a Fedora 14 guest on a Fedora 14 host with Virtualbox, then i run these commands on the guest:yum install kernel-devel kernel-headersbut if i try to install the virtualbox-guest additions on the guest, is still complains about that it's unable to find the kernel source directory?Ha anyone succeded installing the guest additions on a guest Fedora 14?
I have on my computer 9.1 and I want to try some virtualization. I want to install WinXP or 7 as guest on my U9.1 box. what is your opinion? Which VMware or VirtualBox should I try?
I'm having trouble with my Ubuntu VM's --I'm running a Win 7 Home Premium Host, (8GB RAM, 1TB HDD, NVidia GeForce Video) Oracle VirtualBox (Current version)
-- When I set up Linux VM's w/ 3D Acceleration, and 128MB Video Ram, -- I can't enable the 'Extra' Video Effects, to get Compiz working. -- Even when VBox Guest Additions is installed.
VBox Guest Additions does let me use Full Screen, & Seamless mode, correctly though. But if I try to set 'Extra' Video Effects, it can't find the correct driver.
Code: ps -A | grep compiz Does not show compiz running.
FYI: Nor can I get Unity on 11.04 Alpha 1, under the VM.
I am posting this in the "Desktop Environments" section on the theory that the VirtualBox is indeed a desktop environment.
Bottom lines first - maybe it will make the whole essay below superfluous. Do I need to use the Windows-7 installation disk to install the "guest" OS into this virtual box? (This is the main question.) I suspect it is, after the prompts I get trying to run my guest OS for the first time. Since I have a dual-boot anyway - with Win-7 as the main OS on the machine - is there any way I can configure Virtualbox to use the existing Win-7 installation as a guest OS, without damaging the Windows partitions?
Now the rest of the story:
I just deleted about 100 lines of torturous details, realizing nobody will want to read through all that. 1. Question 2 is optional - I have a 400GB mounted file system on a huge Seagate drive for my guest "hard drive".
I tried adding myself to the group vboxusers but it did not help.
I then read that the reason that i don't have any sub capability when i'm running XP as guest OS using VirtualBox is that I have a open source version of the program.
So I uninstalled the one I got through software center and downloaded and installed one from VirtualBox website. It installs but does not tell me where to find it in the menu so I don't know how to launch the program. It also doesn't show up as an "installed software" when I search for it in software center.
I had a lot of trouble installing Guest Additions within the Fedora 13 Guest on a Linux host. I had to mount the vboxGuestadditions.iso from the Device --> CD/DVD Devices menu. Then I located the appropriate package for my system. In my case it was the AMD64 Linux version.I ran this as administrator in Terminal. I used the "bash" command followed by the package name. This was after CDing the the appropriate directory. The packaged installed, I then rebooted and it worked fine. (Something that would make this easier is to load a script into nautilus that would allow me to open a locatation as administartor at the open window. I'm sure there is something in Fedora to do this but I couldn't find it in a hurry so I used the command line way).
I'm trying to test 10.04 Lucid 32-bit within 9.10 using VirtualBox. Guest additions aren't working fully--I can copy and paste text, but my mouse pointer still gets captured. No indications of any problems during installation. Also, I get the "Ubuntu is running in low-graphics mode" error message starting up, indicating Ubuntu can't detect the hardware properly. Screen size is stuck at 800x600.
I've tried reinstalling Guest Additions, increasing Video Ram to 128MB, and putting screen resolution and vbox device data into xorg.conf. Nothing changes. Actually, there is no xorg.conf on the system, only an xorg.conf.failsafe. I modified that, no effect--though the file gets overwritten on boot up to be what it was originally. I also tried adding my own xorg.conf. That doesn't get overwritten, but also has no effect.
1. Microsoft Windows 7 64-bit Professional HOST Operating System 2. Oracle VirtualBox 4.0.6r71416 on top of Windows 7 3. Ubuntu 10.04 Lucid Lynx 32-bit GUEST Operating System in VirtualBox
I successfully installed the above configuration on May 15, 2011. I had some difficulty getting the Host-Only VirtualBox Adapter to work. I was forced to make a subtle change to the Windows Registry in order to get the Adapter to work correctly. I was successful. I used the Debian Update Manager to update my installation of Ubuntu. Nothing changed on the Windows 7 side. Now, Windows 7 says that the Host-only adapter is enabled, but I don't have a connection to the Ubuntu OS. I can't use PuTTY or WinSCP. When I invoke ipconfig on the Windows side, 192.168.56.101 is the IPv4 address. When I invoke ifconfig on the Ubuntu side, there isn't anything.
I've just tried to install Squeeze on my guest partition, using a magazine disk that offered a live CD version with installer, which I ran in text-based expert mode. The process was not a success.
1. The routine for installing grub claimed (hd0,2) was the same as /dev/hda2 2. Starting Debian's grub from the Fedora bootloader with chainloader failed 3. A conventional start revealed all sorts of problems, ending with "/bin/sh can't access tty"
I can't believe Debian could produce something like that! Has anyone here used their live CD as an installer? Tell me this mess is down to Linux Format magazine!
Tried to install 10.4 Beta2 on my testing machine. Boots but then splash screen starts scrolling really fast though I can notice that 5 dots are moving so no hanging. It takes quite a while and then black screen appears (also scrolling) and I cannot read what's there; last line looks like a prompt. Alt-Ctrl-Del reboots the machine. So I cannot even enter Live mode.
This machine is about 7-8 y.o. P4 2.4GHz (i686) on Asus P4S333/c, 2.5GB ram, GeForce3-Ti200, latest bios 2003 but runs any Linux (I tried) and FreeBSD 9-CURRENT perfectly (Even win7 is installable...but runs badly). On newer machine same CD works fine. The machine is AthlonX2 2.3GHz on Asus M3N78-vm, 4GB ram, onboard chip GeForce8200, HDDs, DVD-RW - all SATA (AHCI). What could be wrong with my old machine? Does Ubuntu still support 96xx Nvidia driver?
Keyboard and mouse failure when trying to run a live Ubuntu disk on an Acer Aspire M1641 desktop. I was trying to show off the Ubuntu system to a colleague when to my surprise as it booted up both keyboard and mouse died. There was no response at all, the only option was to use the power button, rebooting into Vista all back to normal. I tried several other versions of Ubuntu going back 8.04 even Knoppix failed to get the keyboard and mouse working. Even after re installing the windows drivers and several more attempts even changing keyboard and mouse, I could not get any linux live disk to work.
OpenSUSE installed in a Virtualbox Virtual Machine and I want to set a shared folder.
1 - Set up a Virtual Machine and install OpenSUSE 11.2
2 - Create a shared folder on host (HostFolder)
3 - Setup the shared folder in Virtualbox Via the Virtual Machine details or via Devices > Shared Folders...
4 - Install dependencies for running the Virtualbox installer You need to install the right development kernelpackage for your machinetype (use 'zypper search -i kernel' to see what's installed) sudo zypper make gcc kernel-source kernel-hosttype/default-devel
5 - Run the Virtual Machine and go to Devices > Guest Additions This mounts an iso image in your OpenSUSE guest.
6 - Open a root terminal and run
cd /usr/src/linux make oldconfig && make prepare && make scripts && make dep cp ../linux-obj/$HOSTTYPE/default/Module.symvers . make prepare
* A commenter on previously mentioned thread says this step is unnecessary but it doesn't work without on my system. I suggest trying step 7 first and returning to step 6 if that fails. *
7 - Run ./VirtualboxLinux yourhosttype .run from the mounted iso image.
8 - Create shared folder in OpenSUSE (GuestFolder)
9 - Test with sudo mount -t vboxsf HostFolder /home/user/GuestFolder It works? Great! Let's set up the system so it automounts for your regular useraccount instead of root-only access.
10 - Add this line to /etc/fstab HostFolder /home/user/GuestFolder vboxsf defaults,uid=1000,gid=1000 0 0
11 - It works for me but if it still doesn't automount after a reboot; sudo mount -a
I've installed fedora 15 on virtualbox as my guest OS.I've configured bridged networking and I've set my router to assign an IP to it.when it boots up,I have 2 devices shown via "ifconfig" which is "lo" and "p2p1" and none has the ip assigned to it.I'm unable to access the Internet. How can I configure it to do so?I've tried following this tutorial: [URL] but the file "ifcfg-ethX" doesn't exist...it only has ifcfg-lo..... I've installed fedora 15 spin edition which doesn't have a GUI for me to edit network settings...
I have VirtualBox v3.1.0 r55467 running on f12 2.6.31.6-162.fc12.i686. The guest is Windows XP SP3. I need to enable bridged mode for the virtual network interface on the guest. Everytime I enable bridge mode the following error occurs.
Quote:
Failed to start the virtual machine Windows XP. Failed to open/create the internal network 'HostInterfaceNetworking-wlan0' (VERR_SUPDRV_COMPONENT_NOT_FOUND). One of the kernel modules was not successfully loaded. Make sure that no kernel modules from an older version of VirtualBox exist. Then try to recompile and reload the kernel modules by executing '/etc/init.d/vboxdrv setup' as root (VERR_SUPDRV_COMPONENT_NOT_FOUND). When I run '/etc/init.d/vboxdrv setup' i get the following compilation error:
Quote:
Stopping VirtualBox kernel module [ OK ] Removing old VirtualBox netadp kernel module [ OK ] Removing old VirtualBox netflt kernel module [ OK ]
[code]....
dmesg gives me nothing. I have scoured the web .. and even asked on #vbox and #fedora cant get.
Just got back to attempting to play with 10.04 using its Live CD. It consistently goes to the "Log In" page and not the Live CD page on running. I saw a Post specifying a F key to be pressed on boot-up to get to the desired starting point some time ago, but did not write it down. Some advice did say press Any Key but this does not seem to do the job. Tried to use the search function here but no joy. Can anyone remember which F key? Note that as a check, I tried to use 9.10 Live CD and this worked fine, so it is not a machine problem.
I just installed Fedora 12 VM using Virtualbox. The next thing I want to do is install the guest addons.So I mount the drive and go the the folder and I use the command:
Quote: su (my username) VBoxLinuxAdditions-x86.run After that I give my password. The message I get is that This program must be run with administrator privileges. Aborting What Have I done wrong? I used su and gave my password, but it still is refusing to install.I am sure I am missing something very simple.
i am planning on installing virtualbox on a fedora 9 machine and would like to know if it is possible to migrate another fedora 9 (totally seperate) machine to a virtualbox as a guest OS.
I have the nvidia 121.21 file for XP and Win2K. I have the driver running on this box on a dual boot win2k install. works fine. The same file on my guest win2k VirtualBox install says no driver available for my current hardware setup. My video card has the 8400 GS chip set. It is currently running 3D on This Fedora 12 install. Is the problem the VirtualBox will not allow the 3D driver to be installed. The installation had a comment about no 3D when it started. I also have not been able to get control of a USB port Device I need. There any way to have Virtual and 3D video drivers with a USB port?
Can anyone help me with how to create an init.d script that will startup a vm machine in virtualbox at boot? I found this script:[URL]..But it is for ubuntu. I am running fedora 12 x386 and using it as an Amahi server. Very cool, but it would be extra cool if I had a virtual windows machine startup when I booted up this server. Then I could just rdp into it when I needed something in windows.
i'm running VirtualBox v3.0.2 on F11x86_64. As my guest in virtualbox i will am using xp sp3. In virtualbox settings i need the use of my serial port (e.g. com1). I have `enable serial port` ticked, port number set to com1, port mode set to host device and port/file path set to /dev/ttyS0. I have done hours of searching and this is the best i have come up with so far. My question is this: How do i give permission for my guest os to use the serial port?
I opted to install my Linux Fedora distribution, in a SUN VM (Virtualbox). [URL] I have 2 questions:
My current max res available to select is 1024x768. Can I run at 1920x1200? My display indicated that it is 'Unknown'. I don't know if that is in on the deal, or not...
Second question: When installing VBOXADDITIONS_3.1.2_56127, I am getting the error: Building the VirtualBox Guest Additions kernel modules [FAILED]
If I am displaying the log correctly, it indicates: Makefile:23: *** Error: unable to find the sources of your current Linux kernel. Specify KERN_DIR=<directory> and run Make again.. Stop Pictures are located here, in the EVGA Linux forum: [URL] I am new to both Linux, and Fedora.
My mission statement: To run Linux using the Fedora distribution, in a VM window under Windows 7 64bit Ultimate, with the ability for scripting using Bash, with the Perl programming language installed, and use Apache Tomcat to monitor both apps, and various VM installs, on numerous Servers via the internet.
I downloaded the .ISO for Fedora Core 14 Live, with the intention of installing it to my HDD.
I burn the .ISO with no reported problems.
I boot to the installation CD and can get to the point where it asks me to Login (a timer is also going down for Automated Login).
Once I click "Login", nothing else ever happens.
I can hear the disc spinning in the drive and it's trying to load something, but it never does.
I thought that maybe my older (2003) laptop might just be slow, so I allowed it to do whatever it seemed to be doing overnight while I slept.
Well, I woke up this morning and it was still doing the same exact thing with no results.
---------- Post added at 05:54 PM ---------- Previous post was at 05:51 PM ----------
Oh, and I intend to dual-boot. I have already made a partition using Norton Partition Magic. It's NTFS filesystem for now, but I figured the Fedora Installation would give me an option to use that partition anyway - NTFS or not (meaning, it would wipe the NTFS file system and use whatever it is that Fedora Core uses). Am I mistaken in assuming this?
I have been trying unsuccessfully to install fedora 10 or 11 on my older PC. I have trieddoing a text install with acpi=off and i8042.nomux but with the same results. The installation sticks indefinately at the anaconda load. CTRL-C works, so it's not a hardware freeze.
Hardware:
Pentium 3 500Mhz Slot1 130 or so MB of ram 2 Maxtor IDE drives CDROM 56x Riva TNT2 video 128
Downloaded few minutes ago Fedora 15 live x64 and used Fedora live usb creator to make my usb drive bootable.Once configured correctly my bios Syslinux starts but it hangs on the startup message
When I attempted to install 64-bit Fedora from my DVD, it failed while installing packages with the unhandled exception:
" Traceback: File /usr/lib/anaconda/users.py, line 163, in setRootPassword, self.admin.setpassUser(rootuser,cryptPassword(pass word,algo=algo),True) File /usr/lib/anaconda/instdata.py,line 171, in write,algo=self.getPassAlgo()
[code]...
I know Python quite well but I have no idea why None is being passed as the first argument to self.admin.setpassUser when a non-None value is needed. The other curious thin is that the trace does not show the call to setpassUser() from the entry after it but rather to 'getPassAlgo(). Needless to say this but has kept me from installing Fedora 11 on my 64-bit machine.
