I have 17" ASUS wide monitor linked to ATI Radeon HD 3870, when I try to install FC10 (from a burned DVD) I can't go beyond "running anaconda..etc" then it goes to a blank screen with a following message "OUT OF RANGE"Now what can I do to bypass this? I want to install FC10 on my desktop?
View 8 RepliesI cannot install Fedora core 10. It boots up and it gets to the Fedora 10 loading screen. After that it complains my monitor is out of Range and that's as far as I can go. I had originally thought I could get to some text install mode, but I don't make it far enough to do that.
View 1 Replies View RelatedI think the settings in /etc/X11/xconf.org are wrong. I do know what the settings should be and have SSH access, (root plus password). Being new to linux I cannot figure out how to save the file after editing. I have been using: vi /etc/X11/xconfig.org to get to the file, but haven't been able to save the file.
the edit and save commands I need, I hate to do an entire install since this is about my 6th install.
get me understand the short range and the long range links from routing (and routing protocols') point of view.
View 6 Replies View RelatedI want to plot a set of data in only one plot.The problem is that some points of the data should be better plotted in a linear scale (lets say 0 to 100,000) but there are other data points that, exceding the value 100,000, would be better plotted in a logarithmic scale, as they goes in the range 100,000 to 500,000,000. Let's say the data is:
Code:
X Y
0 100
10000 80
20000 75
[code]....
Is there a way to plot all these points in the same plot in only one X-axis showing two different ranges in that axis: linear: 0-100,000 logarithmic: 100,000 - 1,000,000,000?The axis would be read, for example, as:
Code:
|-----|-----|-----|-----|-----|-----|-----|-----|-----|
0 20k 40k 60k 80k 100k 1M 10M 100M 1G
(The abbreviations k-M-G are not the important point. Just shown for clarity)
I want to build a bash script, which can ping a range IP adresses which will be filled in by the admin. If there is no IP-adress filled in, then the script must ping the subnet where the system is logged on. So if my ip is 192.168.1.6, then the script must ping from 192.168.1.1 till 192.168.1.255 Or else, if there is given a beginning and ending ip it must ping that!
The first part of the bash script is to ping a given range (see below). But there is one problem, how can I tell the script to ping from $begin till $end, [..] is of course wrong! But what must be filled in there???
echo "Enter beginning IP-adres:"
read begin
echo "Enter ending IP-adres:"
read end
ping -c 1 $begin [..] $end
The second part is to find my own ip and ping the whole range.. How to do that? I only can find my own IP, but I cant ping the whole range,, how to do that?
#!/bin/bash
ifconfig | grep 'inet addr:' | grep -v '127.0.0.1' |
cut -d: -f2 | awk '{ print $1 }'
I run Windows 7 on my home PC and I recently installed Fedora 14 on my USB. When I boot from the USB, I see the Fedora loading screen (3 bars overlaying each other), but once its fully loaded and goes to move forward, both my monitors go blank, one says "Out of Range", the other "No Input".
View 1 Replies View RelatedGot the problem where after the Bios loads my screen just says "out of range" and I cant do anything else. Running on a live cd.
View 7 Replies View RelatedI've just finished installing Centos 5 on a dell server. Reboot after install - it goes through the motions and gets to the point of loading the GUI. At that point screen goes out of range. I've tried 3 different monitors...
View 1 Replies View RelatedMy last Linux install was SUSE 6 on an early ISA based Pentium clone. I'm used to Unix / bash from OS X, MinGW, QNX & BeOS... none of these rely heavily on X. But I'm thinking that Linux is so popular, I'm doing a lot of my Windows stuff under MinGW, why not just stick Linux on and be done with it.So I've polled the various distros, I'm a power-user / dev so Ubuntu doesn't seem like me, and I'm not familiar enough with Linux to go Gentoo just yet, but the way I slim Windows and OS X installs down to just what I need. I love apt-get and like FreeBSD installs I've seen, but want some Linux kernel goodness for my self, so I have chosen Debian.
I grabbed the amd64 build of lenny DVD 1, partitioned up and installed a bare system that I can apt-get the bits I want later.Here's the problem... When the install completes rebooting sends the graphical login to a frequency my old Hanns-G TFT can't handle.I can Ctrl-Alt-F1 back to the terminal or boot in single user mode, and everything seems to be good until you go GUI.Here's what I've tried.
I've renamed /etc/X11/xorg.conf to /etc/X11/xorg.conf.oldI ran dpkg-reconfigure xserver-xorgI've reinstalled using both simple GUI and Expert GUI using both kernelsI've tried adding nvidia-* packages with apt-get and aptitudeI remember there used to be a frequency tuner app for SUSE 6 and XFree86, but it seems that sort of thing is depreciated in modern Linux.Info? My GFX card is an nvidia GT 220, the motherboard is an ASUS P5QL Pro, the Monitor (Hanns-G) is attached via RGB HD-15 D-Sub (sadly that's all I have access to right now) and it's native resolution is 1280x1024 4:3 @ 60Hz, but in heXPee it will sync at that resolution at 60, 70, 72 or 75Hz, though it does get fuzzy at 75Hz.I'm fairly certain that X is working, just not at a frequency my screen can display... how can I fix this from single user, or regular bash terminal?
---edit--- Forgot to mention I ran dpkg-reconfigure on the XServer. :s It didn't offer video drivers, only to change from gb 105 keyboard layout and ps/2 mouse. I set the META key to the logo key while I was there, but it wasn't really helpful in any other way.
After a fresh install of debian 5.05 over net it boots then at end of text lcd screen shows out of range. if start in single user then startx it goes out oif range. How can i set it to a range monitor can do?
View 4 Replies View RelatedI havent used ubuntu since intrepid, but came back from arch linux excited to try lucid
After I've burned the live cd, I can get to the menu (try ubuntu, install etc), but whenever I try to start ubuntu the frequency goes out of range.
I have tried adding vga=771 to the end of the boot line, this had no effect.
EDIT: Am downloading the alternate now.
I upgraded to ubuntu 10.4 and now my screen says out of range. I can hear my normal login noises. sounds like I am working blind. after I log in I cannot do anything without knowing whats going on. I tried ctrl-alt + to try to change screen resolution but I cant tell if it pops up. nothing new happens. I cant slave my hard drive to my other windows or linux OS or linux Live CD, it tells me I dont have permission to open files so I can rescue my files. DO I have to buy a new graphics card or new monitor?
View 1 Replies View RelatedI just installed the latest version of Ubuntu on an external disk (500gb) giving 12gb to Ubuntu.
After the installation process finished I did reboot. When BIOS loaded instead of the Ubuntu boot screen a message from the monitor presented like this:
information
out of range
93.0kHz/58Hz
So I suppose that there must be a monitor problem or something.
I recently installed Fedora 12 -- a brand new install, not an upgrade. The system was previously using Fedora 11 without any problems. Fedora 12 installed without any issues, and I haven't really done any customization to it. I am running KDE. The system is hooked up a KVM switch.
When I am on system #2 (a Windows system) and I switch back to system #1 (Fedora) after a few minutes of time, the Fedora screen will be blank and the monitor will present an "input signal out of range" error. I can SSH into the box and kill X to get the screen back. This has not happened on this system with any previous versions of Fedora that had been running on it (everything since Fedora 7).
I am running an AMD Athlon 64 with an NVIDIA 6600 video built into the motherboard (PC Chips). My monitor is a 19" LCD with a standard VGA connector. I tried installing Lenny and everything went smoothly. However, when I rebooted, the monitor said "Signal out of range." I had this happen with a live CD of another distro too.
View 1 Replies View RelatedI just updated my Wubi install of 9.10 to 10.04 last night. Everything went well until it required me to reboot the computer. I rebooted, loaded Ubuntu from the startup list, and then the screen went blank and I got "H.V. frequency over range" on the monitor.
I can load the GRUB options, but recovery mode using the most recent kernel does not work. I am entirely unexperienced with using the terminal and command prompt options.
Here's what I have attempted so far:
$ sudo dpkg-reconfigure xserver-xorg this did not do anything, the command was not recognized
$sudo nano xorg.config I don't even know what to do when I get to this screen
and I am about to try $ sudo displayconfig-gtk
I have an ATI Radeon 9100 IGP card
this has happened with a few different attempts of ubuntu based distros lately ... i try to boot a live cd it gets to where it starts loading and the monitor pops off and says input out of range ... im aware that this is a known bug with xorg choosing either the wrong resolution or refresh rate ... but what the heck are we supposed to do , i can't get far enough into the boot process that i can open a terminal and try to bypass xorg ... so will all future distributions of ubuntu just be out of the question for me ? if you ask me what needs to be done is make the installer ASK what resolution you want to attempt to boot at .... similar to what puppy does
View 2 Replies View RelatedMy only unhappiness with 11.04, after I installed in on 4/28 on my Eee PC 1000H (dual booting with Windows XP), is that the range of wireless reception in my house, from exactly the same spot as before, has worsened considerably. No problem when running Windows (which I'd rather not do, of course). Could the upgrade have installed a new driver for the wireless hardware that isn't as good as the previous one?
View 1 Replies View RelatedI'm assuming that the following should block the complete 178.123.xxx.xxx address range.
Code:
iptables -I INPUT -s 178.123.0.0/24 -j DROP
Then I believe that I need to save this change.
Code:
service iptables save
iptables: Saving firewall rules to /etc/sysconfig/iptables:[ OK ]
However, I'm not so sure that it is actually working based on the fact that there continues to be access to my wiki from that address range. The following is after I made the firewall change.
Quote:
178.123.177.61 - - [31/Dec/2010:04:24:40 -0500] "GET /mywiki/Opera%20Web%20Browser?action=edit&editor=text HTTP/1.1" 200 6346 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1)"
code....
Let me state that I'm new at this iptables thing. I did some reading and decided that I need to make the above change to the firewall but it doesn't seem to make a difference.
I've just installed Karmic and get an Out Of Range message on my monitor when starting.I had to use the alternate install in order to get Karmic on there in the first place.I have an Nvidia GeForce 7600 GS, and a BenQ FP767-12 TFT.
Output of lspci;01:00.0 VGA compatible controller: nVidia Corporation G73 [GeForce 7600 GS] (rev a2)Not sure how to get my xorg.conf as I can only get to a shell. Here are (what I think are) the important bits;
Code:
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "screen0" 0 0
EndSection
Section "Module"
[Code]...
I'm currently trying to install 10.10 on my (8-year old) desktop, but I'm getting a warning that says "PC video resolution is out of range. Change setting to Recommended resolution 1924*768@85Hz".
Which would be fine, if I knew how. Is there any way to do this in the installer? I can't get any further than the "Try/Install etc" menu screen.
It has a nvidia Geforce graphics card, if that helps. I can't give you any more info than that because the specs have been lost to the mists of time and old email addresses.
My brother got a new 120hz monitor, but can only get the old one to work. If he boots up with both of them connected in windows xp they work fine, but in Ubuntu 10 only the old one works. If he tries to detect the monitor in Display Preferences, nothing happens. The old monitor is connected to vga output (lcd with vga only) the new monitor is connected to dvi with a dual-link dvi cable. We know the graphics cards cannot provide 120hz, for now we run the monitor at 60hz until he upgrades the rest of the pc (sandy bridge i guess).The 120hz monitor worked fine until he changed graphics card from a ATI radeon 9200 to a geforce 3 ti 500.
He has tried
sudo dpkg-reconfigure xserver-xorg
and detect monitor in Display Preferences but no dice. Could he try restricted drivers?
System specs:
Ubuntu 10.04 32bit
athlon xp 1700mhz
1GB ram
ati radeon 9200
geforce 3 ti 500
lg w2363d
Is there a way to turn a laptop, or any PC with a wifi network card, into a wifi range extender? Suppose I have the usual wifi router, but unfortunately the signal doesn't cover the whole house; a solution is a range extender, but I thought: if I have a laptop, placed in the same room where I would put that range extender, can't I use THAT as a range extender too? After all, range extender at the very heart are "stripped-down" routers, which in turn are stripped down PCs equipped with a stripped-down version of the Linux Kernel...
View 4 Replies View RelatedI use F12 and I need help with correct syntax to specify range of IP address in hosts.allow or hosts.deny or in /etc/exports file eg. 192.168.1.100 to 192.168.1.255.
View 13 Replies View RelatedI must say I am newby using Fedora, but cannot find solution how to define print range in calc. I am using oo for almost ten years in windoze, but this is first time I have this problem. I'm using Fedora 14 L, on my lap compaq 6715b. During install, everything went just fine, only problem in last month, since I install F14 L I have find, was using oo calc. I need that rather quickly because I need to apply my tax income until end february,
View 3 Replies View RelatedIm currently using kernel version 2.6.33.3 and i have recompiled. I have bought a serialboard(PCIe 7800) from addi-data and im not sure whether it is properly installed.
When i type in "cat/proctty/drivers", the listing contain a line:
When i type in "lspci",
From my card distrubutor, 7013 means it is APCIe-7800. meaning my system identified the board correctly. why is there an "Unknown" word in the line?
When i type "dmesg", it only shows i have 4 ports,
And i dun have the identification of the PCI slot in which the board is plugged from these "dmesg" command which are usually type MMIO.
I am working with NS-2, I am facing a situation where I need to re align the transmission range of a particular node. Can I do this by modifying the protocol's source code? I should not change the default value from 250, only few nodes who satisfy a particular criterion should be reset to some other range like 200 or 300. How can I do this?
View 1 Replies View RelatedI have a DHCP server running on CentOS and for some reason it is assigning the highest number from the IP range as a first one?
- range 192.168.1.20 - 192.168.1.50 - so the first IP on my PC recived from this DHCP server was .50 - is it normal behaviour?
Config file:
I need to write program (preffer Python) to change range for users. Does anyone know some library which can help me to do that? Maybe someone has written program like that?
View 5 Replies View Related