Got new keyboard yesterday. Could easy set up it when was logged in. After reboot it doesn't work at all. Running fc11-2.6.32.21. Has anyone have any ideas / solutions?
View 3 Replies
I'm trying to install slackware 32 bit 13.1.After loading kernel it asks for keyboard configuration, but keyboard (usb wireless) doesn't work.
Keyboard works on the old 13.0 installation, on bios and also in the boot options of 13.1 installation cd.
I've tried removing legacy usb support and changing usb2.0 speed from high to full. Nothing changed.
Anybody with this strange problem? (kernel of setup seems also to detect it correctly as a trust keyboard).
I want to install Linux on my laptop. I started with Arch but 4 hours later, I'll take anything so now I'm trying Ubuntu.It appears that the keyboard function button that corresponds to my wireless does not work, and perhaps is windows dependent?Every time I try to interact with wlan0, I get the error "Operation not possible due to RF-kill". And as I've looked around online, it has been suggested in other forums that the only way to resolve this is to reinstall windows and dual boot, so the FN key will work.
I think this is ridiculous. There must be a way to persuade the RF-kill to be turned off again, shouldn't there?I don't have a recover disk for this laptop and I don't want to go through the trouble of requested one from acer. I reformatted the whole disk while attempted to install arch.
I have installed Fedora 12 on my laptop.Installing my Broadcom BCM 4312 wireless drivers works just fine, but after a reboot I have to reinstall them. modprobe wl, modprobe wlan0 etc doesn't work either. I need to reinstall them every time I reboot.
View 7 Replies View RelatedStruggled a little to get Broadcom driver working with my Dell laptop. But I am at a point where if I manually type 'modprobe b43' the wireless works. If I reboot, it doesn't work automatically and I have to 'modprobe b43' again. Any ideas what I am missing here?I can't seem to figure out how to get this to work automatically. I did check to activate device when computer starts in network manager
View 1 Replies View RelatedI have tried fedora 14th and also latest ubuntu but my lenovo notebook keyboard did not detected by OS. i think it is due to some kernel missing. keyboard work if acpi=off. My laptop is "Lenovo s10-3c". 1GB RAM, 160 GB Disk.
View 3 Replies View RelatedI just installed Fedora 13 on a Medion E1210. The main problem i have is that the keyboard of the notebook doesn't work. If i use an external USB-keyboard it works fine.
View 2 Replies View RelatedGot myself in a bit of a squeeze here. I was messing around with the Xorg install on my Fedora 12 system. I ended up reinstalling it. Now my mouse and keyboard work fine in single user mode / terminal. But if I try and boot to X they dont work at the login screen. HAL and udev are booting. Ive done a udevadm monitor test in single user mode and its seeing the devices connect and disconnect. Ive also tried both USB and PS2 devices. Same issue. Ive tried playing with xorg.conf and generating it with Xorg -configure :1 I dont know to use to fix it. After banging my head against the wall for 20+ hours I decided it was time to ask for help. m just Lynxing around the web at the moment =X
View 2 Replies View RelatedRecently I have installed Fedora 14 on my other laptop. It's a dual boot with Windows 7. Everything worked perfectly fine, networking included, until my friend didn't accidently turned off the wireless by pressing a wireless button on the laptop. Since then the wireless on Fedora doesn't work. It does on Windows thought. I've tried restarting the laptop few times, but the wireless still doesn't want to work again.
View 2 Replies View RelatedI'm running fedora 13 on a Dell Latitude E6500. It's a dual 64-bit system.
It was working, but then I tried to swap caps lock and control.
I used:
System->Preferences->Keyboard
Layouts->USA->Options
Then, under Control Key Position, I selected swap caps lock and control.
Now, my keyboard won't work in the Keyboard Preferences test area or in any other window or when the screen-lock comes on.
I tried logging out. I tried rebooting. I tried deleting my .gnome2 directory. Nothing seems to work. I can use the keyboard on other accounts, so the keyboard is not the problem.
I downloaded the Fedora 11 KDE livecd, installed it, and after the reboot when I get to that "firstboot" screen, I can't move the mouse, the keyboard doesn't work, I have to hold down the power button to turn off the computer.
View 11 Replies View RelatedI have problems with keyboard layout switcher. On Gnome everything works. But when I start to use other DE I can't switch keyboard layout by default. So I create xorg.conf, but anyway it doesn't work...
View 1 Replies View RelatedI have HP 620 and i installed Fedora 14, but my wireless card doesn't work. My card is:02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvA Wireless LAN Controller (rev 10) Under Live Ubuntu the card works very well, but under fedora doesn't work.It's look like the fedora doesn't a driver.
View 1 Replies View RelatedDell Studio 1555 (Wireless WLAN 1397 Half MiniCard (4312bg)) Wireless doesn't work after update of kernel (kernel-PAE-2.6.38.8-35.fc15.i686)
Quote:
Originally Posted by iwconfig
# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
What should I do to repair wireless?
I saw that Evolution 3.0 was available for 11.04 so I decided to give it a shot. I installed it via ppa following these directions:
[URL]
There were a bunch of dependencies that installed and required a restart. Upon reboot, autologin doesn't work and graphically the desktop is uglier with a different theme. Unity is not working properly, the wallpaper does not exist and many, many artefacts are present.
Screenshots:
Based on my description and the posted instructions, is there a way to undo what I did short of a format and re-install?
I read about PulseAudio and thought it might be nice to try (especially the way you could individually control the volume of all applications seems nice), so I installed it and it worked fine.
I rebooted, and now it doesn't work again. Before, when I opened pavucontrol and went to the "Output Devices" tab, it showed the actual output sevices I have. Now it only lists one called "dummy output".
So what's the problem? Also, can I start it before X11 (I guess that putting "pulseaudio --start" in ~/.bash_profile should do it)?
I've currently got the beta of fedora 12 installed, hope to upgrade that once the final release comes out. I'm having so many problems getting wireless to work. I've got a edimax ew-7711utn wireless adaptor. It doesn't work. Really what I want is to take it back and get a wireless card that will work.
View 6 Replies View RelatedI installed Fedora 15 64 bits version on my desktop, and I'm having hardtime activating my wireless card.
I tried following the instructions from this thread without success [url]
Here are the logs of some of the commands I used
lspci output
Code:
iwcconfig
Code:
Code:
I have a Microsoft LifeCam webcam. It works great under Ubuntu 10.04... Until I reboot. After the reboot, Cheese reports no device connected. I have to get down behind my PC, unplug the webcam and plug it in againThen it works... until the next reboot.
View 1 Replies View RelatedI am a convert from Ubuntu (9.04 kept freezing on my laptop; when it did work, many packages it seemed were outdated--ie only Eclipse 3.2, rdesktop was messed up [and apparently is also in Fedora]), and I am having some trouble with getting my wireless working.I am running Fedora 11.First off, there is a problem when trying to connect when using DHCP. NetworkManager gets to the second green dot, and then after a short while I am given a message that the connection was disconnected.
Configuring the interface manually, not using DHCP, allows the connection to complete. However, the internet is very slow. There is a 15-30 sec delay before website loading actually commences, and then another delay each time an ad must be fetched from another server.How can I fix this delay? I know I have encountered it in earlier versions of Ubuntu, but I can't remember how I fixed it.About the rdesktop problem, if anyone is able to help [maybe I should post another thread?], the cursor color (the color of the pointer) is inverted---where it should be white it is black, and where it should be black it is white. I use rdesktop a lot to connect to my terminal server in my basement. Any idea how to fix it?
last week while I was using ssh to the computer1 inside a NAT as usual, I made another tunnel from the computer1 that I was connecting to, to another computer2 inside that NAT (ssh 192.168.1.130) and after making some changes in computer2 I typed reboot. The computer2 rebooted but the tunnel totally hung and I had to kill it in my laptop. Since that day I haven't been able to ssh to the computer1 as I am used to.
Here is some more information:
debug3: authmethod_is_enabled publickey
debug1: Next authentication method: publickey
debug1: Offering public key: /home/une/.ssh/id_rsa
[code]....
I wireless network card is Broadcom Corporation BCM431, but is doesn't work after I update kernel from
2.6.29.6-217.2.7 to 2.6.29.6-217.2.8.
Linux localhost.localdomain 2.6.29.6-217.2.7.fc11.x86_64 #1 SMP Fri Aug 14 20:53:08 EDT 2009 x86_64 x86_64 x86_64 GNU/Linux
I cant log in as user. My keyboard doesn't work, not even ctrl+f1. So i cant get dmesg....Only thing that is working is alt+print screen+REISUB.
When i booted in safe mode from grub i can log in but only if i enter my root password. And then do /etc/init.d/gdm start.
If i tray to continue straight to gdm in safe mode my keyboard is not working so i can`t log in.
Day before i notices`d that i cant log in with ctrl+f1. When i tray i get this masage madone-desktop login: madone /bin/sh : cant open madone
Windows crapped out on me (not surprisingly) and I am using Ubuntu to transfer all of my files to an external hard drive. However, when the computer loads the Ubuntu disk I get to a language selection menu, but my keyboard doesn't work. It won't let me make any sort of selection, and the 30 second timer eventually times out and my system just restarts and the process starts all over again.
I've tried plugging my keyboard in to all of the different USB ports on my computer, but still nothing. The strange thing is that the keyboard works just fine when I changed the BIOS settings to boot from the cd-rom... it just doesn't work when Ubuntu is ready to run..
I created a bunch of keyboard shortcuts via "System > Preferences Keyboard Shortcuts," and they all work flawlessly except one: Nautilus. I just set it to run the command "nautilus" and it doesn't do anything. My GNOME panel launcher runs the same command just fine.
View 3 Replies View Relatedafter I updated my BIOS , my keyboard didnt work in grub , but I can use it before grub.
View 2 Replies View RelatedI've got a Compaq MX 11800 keyboard that has a ball (used as a mouse). The ball works fine in Ubuntu and Windows, but does not work in Debian or Fedora.
I don't know where to start troubleshooting this issue. Any help is appreciated.
Here's a picture of the thing: [url]
I have installed knoppix 6.0.1 persistent to a usb flash drive. I am currently testing it on my laptop and have successfully installed the graphics driver for nVidia Geforce 7150m driver 180.51
All looks great until i restart and it doesnt work again. when i go to reinstall it, it says its already there, but when i open the nvidia-settings, it doesnt look the same as before. If i reinstall it, it works again, until i restart of course.In case this is important, here is how i installed the driver in root terminal:
sudo apt-get install gcc make
init 3
cd /home/knoppix/Desktop
sh NVIDIA-Linux-x86-180.51-pkg1.run
(A series of questions come up asking to compile a kernel, etc.)
(install runs)
init 5
I am guessing that the new kernel needed for the driver that is installed is not being booted up on when knoppix restarts. I am just unsure as how I can make this kernel accessible at start up or how to start up this kernel again without reinstalling the driver
I just installed Debian Testing (with Xfce) along side Win7 on my Dell XPS M1530 and now neither my keyboard nor my USB-mouse work at the login screen. Both worked perfectly during the installation and Grub as well recognizes my keyboard. The Numlock-LED can be switched on and off during the boot, but fails to work at the login screen.
View 2 Replies View RelatedI wanted to type something in french so I started the on board keyboard so I'll know where the letters are. Now my keyboard is locked, and the onboard doesn't work too... all I did was to click on some of the settings of the onboard.Sadly the onboard didn't show me the french keyboard, so that's a downer too.
View 1 Replies View Related
