I recently got the printer part working by downloading from canon the correct rpm also in doing this I got the scanner driver. My computer tells me it is installed but I see no program to connect with my scanner. There is nothing in xsane or simple scan to allow me access to the scanner.
View 5 RepliesI'm trying to get my Canon Pixma MG 5150 scanner/printer to work. While the 'printer' is doing well the 'scanner' appears to be stubborn. I use the scangearpm-MG5100series-1.60-1 driver provided by Canon which is said to be fine with Suse 11.2.
The trouble is, that though the scanner scans it does not deliver anything back. Here are the details:
When I run scangearmp as root in a terminal I get the following output:
Code:
(scangearmp:6902): GVFS-RemoteVolumeMonitor-WARNING **: cannot connect to the session bus: org.freedesktop.DBus.Error.NoReply: Did not receive a reply. Possible causes include: the remote application did not send a reply, the message bus security policy blocked the reply, the reply timeout expired, or the network connection was broken.
[Code]....
Are there any (easy to install) (X)SANE backends for Canon PIXMA MP460?
View 1 Replies View RelatedI just downloaded and installed openSUSE 11.2. It looks good. Very fast and extremely stable.
My problem is that I use a 'Canon MP280' Printer / Scanner / Copier.
It seems that my printer and openSUSE are not compatible.
OpenSUSE can't find Canon MP280.
I just received a Canon Pixma MX320 as a gift.
I am currently running the Ubuntu 10.04 OS
I was able to get the printer up and running by downloading the printer driver for debian linux (3.1) from the Canon site without any problems.
Unfortunately I am not having the same luck with the scanner.
I tried downloading ScanGear MP for Linux (deb) (1.3) from the same Canon site but have not yet been able to get the XSane Image Scanner to recognize this scanner driver for my Canon.
I have installed Fedora 13 on AMD x86_64 plattform. I want to add the Canon PIXMA iP1900 printer, but cups doesnot have in the repo. (127.0.0.1:6xx). Then i visited canon-europe webpage, and i downloaded the rpm version of the printer driver. But it no works! and the printer isnot added to the repolist of cups.Who can i solve this problem in Fedora 13 ?
View 1 Replies View RelatedA neighbor of mine just got a Canon Pixma MP450 printer, to replace an old HP printer, and I am trying to get it to work with Fedora 11 installation from a machine they have borrowed from me. The printer gets recognized upon plugging it in but when I try to print a test page from the printer properties I receive the following error:'client-error-document-format-not-supported'
The driver that is selected for the printer is "Generic Driver" I have tried to select a driver but have not found any Canon drivers from the selection dialog box. After searching the web I see mention of a Canon MP150 driver working for the MP450 but I have not found this driver. Is there a driver I have to install from YUM or download from Canon? Are there others successfully using this printer and if so what have they done to get it to work?
How to get this scanner to work with Ubuntu 10.10
It's connected and printer is working through the scanner.But i can't get the system to recognise the scanner.
I'm all new to Ubuntu, and i thought it was easy and terminal is a totally new thing to me.
Is there a workaround to get this scanner to work through graphical interface install, or is terminal wisdom needed...
Recently got a Canon Canoscan 8800F after looking it up on the SANE site and said it was completely supported for Linux.
I have downloaded the pixma drivers and have compiled the command line program, but it can't find the scanner.
lsusb returns a Canon scanner Bus 001 Device 005: ID 04a9:1901 Canon, Inc.
and sane-find-scanner returns:found USB scanner (vendor=0x04a9 [Canon], product=0x1901 [CanoScan]) at libusb:001:005
but scanimage -L (under my user login or sudo) returns only the webcam. No other scanner found.
My system is running Linux Mint 7, ia64 kernel 2.6.28-11-generic
I have a Canon Lide 100 flatbed scanner, however xsane 0.997 can't detect it.Just wanna ask you you guys add a scanner ?When I do a command line, this is what I get.Quote:[root@localhost]# sane-find-scannerfound USB scanner (vendor=0x04a9 [Canon], product=0x1904 [CanoScan], chip=GL843) at libusb:001:003However when I run the "Scanner Tool" from Application --> Graphics --> Scanner Tool
View 7 Replies View RelatedI want to get my Canon MP210 printer / scanner working under Fedora 8 Linux. When I plug the USB cable in, I get a little popup with a setup wizard, but my printer isn't even in that list. I've tried the system-config-printer wizard as well as going in through the control panels and trying everything reasonable.
View 5 Replies View Relatedfedora can't detect my scanner 5600f !!how can i do ? i can't scan pictures ? is there any solution ??
programming ?? driver ?? can i do somthing with sane genesys and GL841 chipset??
Does anyone have an idea of where i can find a driver for this printer? The system does not have one and if I try a driver for say the PIXMA MP220 which is CUPS + Gutenprint v5.2.4 [en] (actually, all the PIXMA drivers are that one) and I print the printer seems like it receives some command but nothing else happens. The printer says 'Printing from PC' and then goes back to the main screen.
View 5 Replies View RelatedI was using 10.04 until a few days ago, and with 10.04 my printer worked fine, I used the default drivers for MP150 and that worked fine. But now I'm using 11.04 and I'm trying to instal the printer with the default drivers for MP150 but it's not working. When Ubuntu tries to find the driver is not giving me any result for MP140, so I'm selecting the option "CANON PIXMA MP150 - CUPS+Gutenprint v5.2.6 Simplified [en] (Recomended)" and allows me to click next and to give a name to the printer and to hit next, but then the windows closes and that's it then I go to System > Admin > Printer and I double click the printer I just created and I click Print Test Page and then it gives me "Printer Status: Processing - Printing Page 1.8%" and after 4minutes or so gives me "Installation or actualization of package "python-xmpp 0.4.1-cvx20080505.2" failed" and that's it Is there a way to fix this? I have no idea why this is not working since it worked fine in 10.04, and I really need to use the printer and the scanner as soon as possible
View 3 Replies View RelatedI have just installed SUSE 11.2, but although my ip3000 shows in the hardware, I cannot get a correct print out on A4 paper and I am informed that no driver is available. There must be a work-around for this?
View 6 Replies View RelatedIt's weird because it did not even print different shades of gray (for the colors), as though I set it to print to black-and-white, when clearly I did not.
View 3 Replies View RelatedI'm trying to get my Canon Pixma MP510 scanner to work under openSUSE 11.3. Canon Linux Support doesn't seem to have anything for 11.3, but sane claims to provide basic functionality. The printer is working fine, but I don't manage to configure the scanner.
I tried to configure via YaST, but the following happens: The scanner is found, but (correctly) labbelled as "not configured". Clicking "Edit", the PIXMA MP510 is listed and a driver suggested: "Canon PIXMA MP510: (Package sane-backends) Driver pixma should provide basic functionality (USB-ID 0x04a9:0x1717)" If I select this option an click on "Next", the window crashes and I get the following error in the KDialog window, but I have no clue what it means: "YaST got signal 11 at YCP file Wizard.ycp:849 /sbin/yast2: line 399: 5663 Segmentation fault $ybindir/y2base $module "$@" "$SELECTED_GUI" $Y2_GEOMETRY $Y2UI_ARGS"
Is this a YaST problem? Or driver related? I thought about configuring the scanner without YaST, but don't know how to do it. I tried to google a HowTo, but couldn't find anything useful.
The command "sane-find-scanner" successfully detects the scanner, "found USB scanner (vendor=0x04a9 [Canon], product=0x1717 [MP510]) at libusb:001:004", but the command "scanimage -L" yields "No scanners were identified."
how to make YaST configure my scanner? Or how to configure it without YaST?
I just bought a new printer yesterday. It is a Canon Pixma iP2600 series. I connected everything properly and my computer found the drivers and told me the printer was ready for use. However, when I tried to print out a test page the computer said it was printing, the printer was flashing as it should, but nothing was printing out. Is there some switch I need to turn on or off? Is there something that I need to type in or delete somewhere? The old printer was a HP deskjet and it did work even if it was a little slow being that it is over 8 years old.
View 6 Replies View RelatedThere is not a driver for the Canon Pixma ip1800 Printer in Ubuntu. How do I go about getting this printer to work with Ubuntu 10.10.
View 9 Replies View RelatedI have finaly gotten the Canon Pixma MP495 working under Ubuntu 10.10, with full resolution capabilities of the printer.This printer is only advirtised as having a max resolution of 4800x1200 DPI. However, I called Canon to get the full range of print resolutions and was informed that this printer is capable of 9600x2400 DPI.I haven't tested this below Ubuntu 10.04 but it should work fine.
For setting your MP495 printer up on your network without the use of a Windows or Mac machine (Fresh out of the box with Ubuntu) you will need to match your Routers SSID to the printers default SSID, and remove any security you have enabled. This will allow the printer to connect to your network.
Printer Defaults:
SSID: BJNPSETUP
IP ADDRESS: Automatic
Once you have done that you will need to activate the wireless lan on the printer.Press the Maintenance button on the printer 13 times until you see what looks like a capital G without the middle line. Then press the color start button. (refer to page 10 of your Network Setup Troubleshooting manual for an actual picture of the symbol) You should see the wifi light on the front of the printer turn on and be solid not be blinking. (If it is blinking check your routers SSID settings and match the Default SSID of the printer as listed above.
Now download angryipscanner AngryIPScanner and install it by double clicking it. It should open in the Software center or with the Gdebi installer. (this may take a few minutes to install.)Once you have installed AngryIPScanner, run it and change the ip range to include from 1 - 254 in the last octet. Then click start. When it finishes look for an active connection with a Hostname like A001BF000000.local. Yours may be different but should be very simular.
The IP address given for that hostname is the IP address of your printer. Open Firefox and type that address in the address bar and press enter. From there you can configure you printer for the SSID, and encryption that you had on your router before the change, and set a static IP for the printer so you can manage it easily.After you change the SSID and encryption on the printer you will have to go back to your router and change the SSID and encryption back to what it was before so your printer can connect again.Now your network should be back the way it was and your printer should be connected Now that you have successfully connected the printer to your wireless network continue with the rest of the installation. Download the drivers for the MP495 . You will be downloading cnijfilter-mp495series-3.40-1-deb.tar.gz.
Extract cnijfilter-mp495series-3.40-1-deb.tar.gz to your Home directory.Change the permissions of the install.sh file to run and an executable by Right licking on install.sh and then left clicking Properties. Click on the Permissions tab and put a check mark in the Allow Executing file as program box. Then open a terminal and type: [CODE]sudo ./install.sh[CODE] Follow the prompts and if you are using the printer over the network select network when prompted. I you are using it via USB choose USB. Don't forget to scroll down to complete setting up your printer to use full resolution and set up the scanner.If the first method didnt work try this.Open a terminal and enter
Code:
cd /home/*/cnijfilter-mp495series-3.40-1-deb/packages. (Enter your username where the astride is.)
Quote:
For 64 bit systems you need to replace cnijfilter-common_3.40-1_i386.deb, and cnijfilter-mp495series_3.40-1_i386.deb with cnijfilter-common_3.40-1_amd64.deb, and cnijfilter-mp495series_3.40-1_amd64.deb. For the printer setup. For the scanner replace scangearmp-
[code].....
I am new to Linux and to make matters worse, am trying to install a new printer but cannot find the drivers for it. it is a cannon pixma mg 6120.
View 1 Replies View RelatedI recently purchased the canon pixma mg5220 and am currently figuring out how to print to it from my computer.
First of all, I dont know how to connect to it (its a wireless printer btw and is currently connected to my wireless router). I went to the "add new printer" part of the printer utility and selected "Find Network Printer." I dont know what to type in for "host" however. Right now i have a temporary fix of sharing the printer on my laptop (which runs windows) and printing through that.
Second of all, drivers. I found http://ubuntuforums.org/showthread.php?t=1588333 and downloaded the drivers (to my downloads folder) from the link provided, but I can't figure out how to install it. The post says to run the install.sh but it seems to be just a text file, and when i right click it, "properties" is not an option, so i cant mark it as executable. How would can i run this file to install the drivers?
I have recently purchased a canon pixma mx330 all in one printer. I tried using yast on 64 bit opensuse 11.1, kernel version 2.6.27.7-9 to locate the necessary driver to no avail. Is this a futile attempt or is there a driver that yast can't find.
View 1 Replies View RelatedI have a Canon Pixma Ip1300 color printer but I don't know how to install it on ubuntu 10.
View 3 Replies View RelatedI can't get my ubuntu 11.04 to print on canon pixma ip2772, it says that I got canon ip2700 series installed, and show that I am printing a test page, but nothing happens on the printer.
View 4 Replies View RelatedRunning Ubuntu 10.10, when trying to print to canon 1800 print file is created, spooled to printer but does not print. Job appears in print Q and ends as finished job, next job number increases correctly. Printer light flashes to indicate data in,, but nothing out on paper !! (printer works fine on "the Other" OS!
View 4 Replies View RelatedMy distribution of choice is pclinuxos, the repos do not have a driver for my pixma ip4800.I have downloaded the two drivers for this printer from the canon site but so far have been unable to install them or find a specific thread that can help.
View 2 Replies View RelatedI use an Intel P8700, 2 core 64 bit m/c.I have tried downloading the Canon binary files, but these fail after starting when the software detects a 64 bit mc.Now trying with the Canon source files.extracted the print filter loaded the "autogen.sh" which ran and invited me to type "make". Yes! I thought!I have been trying to print for about 5 months now, and am getting weary!George "autogen.sh"ran ./configure, apparently successfully, invited me to type "make" which I did. This failed!I have a copy of the interaction but cannot see any way to add it to this post.
View 6 Replies View RelatedI just acquired this printer. I would like to get it to work with my laptop.I'm running OS11.2 I've looked in yast but it isn't listed. Looked in Canons website and didn't find a driver for linux.
View 9 Replies View RelatedWhen I try to set up my printer a Canon Pixma MP530, there is no driver! Only the Generic ones and they don't work. On Ubuntu using the Pixma MP500 driver works just fine, but there is no option for that on suse. Only for HP and Generic. The only solution I have found was turbo print, and that costs $30. I am hoping to find a solution, I really like SUSE, but I may have to go back to Ubuntu.
View 9 Replies View Related