Debian Installation :: Cannot Make Grub2 Boot Software RAID (Error)
Jun 2, 2011
I have a Dell PowerEdge SC1425 with two SCSI-disks, that I have tried installing Debian Squeeze on. This machine has previously been running Lenny (with grub 1), and the upgrade was done by booting a live-cd, mounting the root partition and moving everything in / to /oldroot/, then booting the netinstall (from USB), selecting expert install and setting up everything (not formatting the partition).
Both disks have identical partition tables:
/dev/sda1 7 56196 de Dell Utility
/dev/sda2 8 250 1951897+ fd Linux raid autodetect
/dev/sda3 * 251 9726 76115970 fd Linux raid autodetect
/dev/sda1 and /dev/sdb1 contain a Dell Utility, that I have left in place.
/dev/sda2 and /dev/sdb2 are members of a Raid-1 for swap.
/dev/sda3 and /dev/sdb3 are members of a Raid-1 for / formatted with reiserfs.
After installation, grub loads, but fails with the following message:
GRUB loading.
Welcome to GRUB!
error: no such disk.
Entering rescue mode...
grub rescue>
Doing "ls" shows:
(md0) (hd0) (hd0,msdos3) (hd0,msdos2) (hd0,msdos1)
I can do the following to get grub to boot:
set root=(hd0,3)
set prefix=(hd0,3)/boot/grub
insmod normal
normal
This will bring me to the grub menu, and the system boots.
It appears that grub has only found md0, which I believe is the swap partition, because ls (md0)/ returns error: unknown filesystem. I have installed grub to both sda, sdb and md1, and tried dpkg-reconfigure grub-pc and dpkg-reconfigure mdadm, as well as update-grub.
I manually added (md1) /dev/md1
to /boot/grub/device.map, but still no result.
I have run the boot_info_script.sh, but unfortunately I cannot attach the RESULTS.txt, because the forum aparently does not allow the txt-extension. Instead I have placed it here: [URL]. I am tempted to go back to grub-legacy, but it seems I am quite close to getting the system working with grub2.
View 6 Replies
ADVERTISEMENT
Apr 20, 2015
I have created a system using four 2Tb hdd. Three are members of a soft-raid mirrored (RAID1) with a hot spare and the fourth hdd is a lvm hard drive separate from the RAID setup. All hdd are gpt partitioned.
The RAID is setup as /dev/md0 for mirrored /boot partations (non-lvm) and the /dev/md1 is lvm with various logical volumes within for swap space, root, home, etc.
When grub installs, it says it installed to /dev/sda but it will not reboot and complains that "No boot loader . . ."
I have used the supergrubdisk image to get the machine started and it finds the kernel but "grub-install /dev/sda" reports success and yet, computer will not start with "No boot loader . . ." (Currently, because it is running, I cannot restart to get the complete complaint phrase as md1 is syncing. Thought I'd let it finish the sync operation while I search for answers.)
I have installed and re-installed several times trying various settings. My question has become, when setting up gpt and reserving the first gigabyte for grub, users cannot set the boot flag for the partition. As I have tried gparted and well as the normal Debian partitioner, both will NOT let you set the "boot flag" to that partition. So, as a novice (to Debian) I am assuming that "boot flag" does not matter.
Other readings indicate that yes, you do not need a "boot flag" partition. "Boot flag" is only for a Windows partition. This is a Debian only server, no windows OS.
View 5 Replies
View Related
May 4, 2011
I switched over from Ubuntu because I realized Ubuntu sucks now (lol), but anyways... Now I'm trying to get Grub2 to boot up properly, but this "xputs" error pops up and drops me to the recovery prompt. I tried the grub-install dev/sda and all it did was recognize my Windows 7 OS (as Vista) and added it to the bootloader list and didn't fix the "xputs" issue.
I heard that doing a chroot is the most effective solution. Forgive me, but I don't know what "chroot" means or how effective it is. I can specify more information about where the OS is if needed. I have the boot flag set to the Debian OS at the hd(0,5) or sda5 I think, and Windows is at sda1 (I think). I just want to make sure I can fix this without damaging Windows, and I'll try to get more information.
Right now, I can only get into Windows or Debian with UBCD and Grub2 Super Disk and I know that sometimes Parted Magic could orderly mount the disks differently, so I don't know if it was sdaX or sdbX, but probably sdaX. I'll check again.
View 1 Replies
View Related
Jul 2, 2011
I have Lucid installed on a computer. I added a second drive, installed Windows 7. Windows 7 boots fine if it is the only drive connected, or it is selected as the boot drive in the BIOS. I booted into Lucid, ran 'sudo update-grub' and it found the Windows 7 install on the second disk. When I try to use that Grub entry to boot Windows 7, I get this error screen:
Code:
Windows Boot Manager Windows failed to start. A recent hardware or software change might be the cause. To fix the problem:
1. Insert your Windows installation disk and restart your computer.
2. Choose your language settings, and then click "Next."
3. Click "Repair your computer."
If you do not have this disk, contact your system administrator or computer manufacturer for assistance.
File: BootBCD
Status: 0xc0000225
Info: An error occurred while attempting to read the boot configuration data.
I seem to remember in the Grub 1.x days there was a map command that would 'swap' the drives so Windows would think it was the boot drive, but the Grub2 autogenerated command doesn't have anything like that.how to get Grub2 to boot Windows 7?
View 4 Replies
View Related
Apr 30, 2010
After upgrading to 10.04 from 9.10 Win7 wouldn't startup any more. So I tried this HowTo: [URL] to restore Grub2. But now each time I boot up I get this two lines: error file not found grub rescue> I have NO idea what to do.
[Code]...
View 9 Replies
View Related
Sep 1, 2011
I recently upgraded from 10.04 to 11.04 and I now often get boot messages about a degraded raid.
I'm fairly experienced, but I'm confused which raid it is talking about. I have a raid5 array, but I don't boot of that, and it seems fine when I finally get it to boot. Previously, I didn't have any other raid arrays[1], but now I seem to have two others called md126 and md127, they both seem to be degraded. Where did they come from?
[1] I *do* have two 80GB drives that I was booting from in RAID1, but that was a looong time ago, and I have since only booted from one of them. The partition table indeed shows partitions 1 and 5 are raid autodetect and /proc/mdstat shows they are degraded ([U_]). Could it be that this is causing the problem? If so, why has this only started to happen since the upgrade from 10.04 to 11.04?Anyway, perhaps it is a good idea to add in that second disk to the raid1 array. If so, how to do that? Note that, I've also noticed that when I boot and get to the screen when I select from the different kernel versions, I now get a couple of really old ones too - my thought is that these are from the raid1 disk that I stopped using. If I add it to the array, how can I be sure it will mirror in the correct direction?
It could be that I have fairly recently plugged in that second RAID1 disk, after a long time of not having enough spare sata sockets (I switched my RAID5 array from 8 disks to only 3 disks, so suddenly had a lot more spare sockets).
View 9 Replies
View Related
Feb 28, 2011
Whenever I reboot, I get GRUB and the _ pinking, and that's it. With rescue cd I can have chroot shell, to troubleshoot I did the upgrade-from-grub-legacy and installed it to both /dev/sda and /dev/sdb In recovery I redid the upgrade-grub and grub-install commands but still have the same "GRUB and _ blinking".
Because the text "GRUB" and then nothing I didn't enouncter while googling, I need to ask here for further troubleshooting.
View 10 Replies
View Related
Feb 9, 2011
This is my specific solution to my specific problem. After updating to Squeeze from my prior Lenny distro (amd64 with whole disk encrytion using LVM2, dm-crypt, LUKS) everything went well - at first. I was duped like so many, thinking that all was well and I could remove the legacy-grub (aka: Grub1) and just use grub-pc (aka: Grub2). As soon as I removed the legacy-grub and rebooted my laptop, I was confronted with:
GRUB Loading stage1.5 GRUB loading, please wait..Error 15 At this point I wasn't sure if it was a Grub problem or a deeper encryption problem - especially after reading that some people had missing packages in Squeeze (lvm2, dm-setup, initramfs-tools, etc.)
Okay, the solution for me.
1. download and burn to disk: debian-live-6.0.0-amd64-rescue.iso[URL]..
2. scroll to and press enter/return on: text rescue
3. choose a root directory - for example: /dev/blah/root (I wrote down the list of possible /dev/.... for reference - this helped me remember where and what I had partitioned in Lenny)
4. choose: Execute a shell in /dev/blah/root
5. once in the shell, I discovered I needed to mount a few of those partitions that I had written down in order to get access to grub-probe, update-grub, grub-install, etc. You may not have to if your partitions are minimal. I you need to use other partitions, type (for example):
[Code]...
View 1 Replies
View Related
Jan 8, 2011
I am looking to build a server with 3 drives in RAID 5. I have been told that GRUB can't boot if /boot is contained on a RAID arrary. Is that correct? I am talking about a fakeraid scenario. Is there anything I need to do to make it work, or do I need a separate /boot partition which isn't on the array?
View 3 Replies
View Related
Mar 7, 2010
i initilally installed ubuntu 9.10 then installed windows 7 ,then i recovered grub2 using livecd as told in the post [URL] i did "sudo update-grub" and got windows 7 menu entry but when i select that entry windows 7 does not load but the grub2 is reloaded again.
i cant boot to windows 7.
Windows 7 have 100 mb partition "System Reserved" the grub2 points to that partition but still windows 7 not loaded.
sudo fdisk -l
Disk /dev/sda: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x3c3a81f5
[Code]....
View 3 Replies
View Related
May 17, 2010
I went through so many post but I haven't found the proper answer yet hope you have an Idea1. Grub2 saves only Linux OS as last selected no Windows OS2.It is possible to boot into a cdrom (drive)?
View 2 Replies
View Related
May 8, 2011
I have been frustrated attempting to get Grub2 to boot a Debian Live system from hard disk. Have set aside a 4gb partition /dev/sda1 to contain the Debian Live and some other recovery tools. I actually have them all working from a 4gb USB stick successfully, but getting it to work on my HDD has proved challenging. On USB, I have PartedMagic, Gparted, Grml, and of course my standard 6.01 Squeeze. I have also managed to get the Debian Live booting from that USB stick. Very slick.
However, I can NOT get Debian Live to boot from my HDD; altho all of the others above boot fine. Have tried it two ways - one using an iSO image, which is how it is done on my USB stick. The other attempt is to copy the entire contents of the ISO to a directory.
Here are my directory structures:
debian_live_gnome_squeeze_i386- contains the following: debian-live-6.0.1-i386-gnome-desktop.iso initrd.gz initrd.img vmlinuz which is how it is laid out on my USB stick debian_live - contains the files from the ISO image The error I get is something like "panic unable to find live filesystem" My grub.cfg snippet for the two methods I have tried - the 2nd menuentry is similar to how it works on the USB stick.
menuentry "Debian 6.01 Live (on /dev/sda1)" {
insmod part_msdos
insmod ext2
set root=(hd0,msdos1)
[code]....
Probly don't really need to get it working since PartedMagic can do almost everything I need for recovery and I can use the USB for reinstall or whatever else.
View 8 Replies
View Related
Dec 22, 2010
I installed Debian 5.0.3 (Backport with .34 Kernel), because my server hardware (Dell PowerEdge R210) needs special firmware and drivers.However, the installation went quite smooth.I put the system on a RAID 1 Array with about 500 GB space.s I said the installation went well, however, it doesn't boot! No GRUB, nothing
View 4 Replies
View Related
Oct 26, 2010
I'm trying to install GRUB2 on root partition under RAID 5. I tried using the alternate CD, but installation failed. Now I'm trying under the live CD and grub-install ... but I'm being told it can't find the device even though /dev/sda2 (root partition) and /dev/sda are mounted.I have 4 discs, each with a swap partition (/dev/sdX1) and a root partition (/dev/sdX2).
View 9 Replies
View Related
Apr 30, 2011
GRUB2 / RAID 10.10 to 11.04 Upgrade Fail.....
View 9 Replies
View Related
Feb 23, 2011
I am attempting to install Maverick on an older pc. It has (2) mirrored 153 GB SATA drives. I set aside 33GB for a linux partition, by shrinking the partition in Vista.
Choosing to "Install along side windows" is not an available option. I can only choose use who disk, or use empty area. I choose use the empty area, and the Ubiquity installer gets hung up when attempting to format the empty space as EXT4. When I scroll up on the output I notice some error messages referencing NTFS. When I use Gparted it shows a possible problem.
Quote:
Warning:
The device /dev/sda1 doesn't exist
ntfsresize v2.0.0 (libntfs 10:0:0
ERROR(2):Failed to check 'dev/sda1' mount state: No such
file or directory
Probably /etc/mtab is missing. It's too risky to continue. You
might try an another Linux ditro.
Unable to read the contents of this file system!Because of this some operations may be unavailable.
The following list of software packages is required for ntfs file system support: ntfsprogs.
I ran chkdsk /r on the Vista partiton, in case there was a problem there. The issue still persists.
View 2 Replies
View Related
Jan 30, 2010
I had Windows 7 installed on my system, then I installed Debian testing with grub2 as its boot manager.Initially I couldn't see windows entry in grub at all, so I ran:aptitude install os-prober kcpuload update-grub Now I can see the entry, but when I select it I get only Win7 system restore, instead of the the real thing. Any ides how to make it work?
EDIT: I tried the suggested approach to add a new file to /etc/grub.d, which generated an entry in grub.cfg, but it does not appear in the grub menu on boot :(
I have this:
grzes:/home/ga# cat /etc/grub.d/11_Windows
#! /bin/sh -e
echo Adding Windows >&2
cat << EOF
menuentry "Windows 7″ {
[Code]...
View 1 Replies
View Related
Dec 1, 2010
I performed an install using the 5.0.6 amd64 netinst cd on a dual opteron server with an Areca ARC-1110 4-port SATA hardware RAID card. I have 2 250GB drives set up as RAID 1. The debian install saw it as only one drive, just as it should. Install went smoothly, but on reboot, the system would not load.
I did some research and tried a couple of things with no luck. Like adding a delay in the grub command. It jus sits at loading system for a while then times out and loads busy box. Just to check things out, I booted into an Ubuntu live-cd and mounted the volume. The file system is there and all of the necessary files. How to use one of these cards successfully?
View 2 Replies
View Related
Sep 19, 2014
I am running a 14 disk RAID 6 on mdadm behind 2 LSI SAS2008's in JBOD mode (no HW raid) on Debian 7 in BIOS legacy mode.
Grub2 is dropping to a rescue shell complaining that "no such device" exists for "mduuid/b1c40379914e5d18dddb893b4dc5a28f".
Output from mdadm:
Code: Select all  # mdadm -D /dev/md0
  /dev/md0:
      Version : 1.2
   Creation Time : Wed Nov 7 17:06:02 2012
     Raid Level : raid6
     Array Size : 35160446976 (33531.62 GiB 36004.30 GB)
   Used Dev Size : 2930037248 (2794.30 GiB 3000.36 GB)
    Raid Devices : 14
[Code] ....
Output from blkid:
Code: Select all  # blkid
  /dev/md0: UUID="2c61b08d-cb1f-4c2c-8ce0-eaea15af32fb" TYPE="xfs"
  /dev/md/0: UUID="2c61b08d-cb1f-4c2c-8ce0-eaea15af32fb" TYPE="xfs"
  /dev/sdd2: UUID="b1c40379-914e-5d18-dddb-893b4dc5a28f" UUID_SUB="09a00673-c9c1-dc15-b792-f0226016a8a6" LABEL="media:0" TYPE="linux_raid_member"
[Code] ....
The UUID for md0 is `2c61b08d-cb1f-4c2c-8ce0-eaea15af32fb` so I do not understand why grub insists on looking for `b1c40379914e5d18dddb893b4dc5a28f`.
**Here is the output from `bootinfoscript` 0.61. This contains alot of detailed information, and I couldn't find anything wrong with any of it: [URL] .....
During the grub rescue an `ls` shows the member disks and also shows `(md/0)` but if I try an `ls (md/0)` I get an unknown disk error. Trying an `ls` on any member device results in unknown filesystem. The filesystem on the md0 is XFS, and I assume the unknown filesystem is normal if its trying to read an individual disk instead of md0.
I have come close to losing my mind over this, I've tried uninstalling and reinstalling grub numerous times, `update-initramfs -u -k all` numerous times, `update-grub` numerous times, `grub-install` numerous times to all member disks without error, etc.
I even tried manually editing `grub.cfg` to replace all instances of `mduuid/b1c40379914e5d18dddb893b4dc5a28f` with `(md/0)` and then re-install grub, but the exact same error of no such device mduuid/b1c40379914e5d18dddb893b4dc5a28f still happened.
[URL] ....
One thing I noticed is it is only showing half the disks. I am not sure if this matters or is important or not, but one theory would be because there are two LSI cards physically in the machine.
This last screenshot was shown after I specifically altered grub.cfg to replace all instances of `mduuid/b1c40379914e5d18dddb893b4dc5a28f` with `mduuid/2c61b08d-cb1f-4c2c-8ce0-eaea15af32fb` and then re-ran grub-install on all member drives. Where it is getting this old b1c* address I have no clue.
I even tried installing a SATA drive on /dev/sda, outside of the array, and installing grub on it and booting from it. Still, same identical error.
View 14 Replies
View Related
May 27, 2011
My old computer started randomly rebooting so I went out yesterday and bought a new one. It's a standard Intel 64 architecture with 2gb ram etc.The old computer was running Lenny however I'm happy to upgrade, so I just went to the main Debian download site and downloaded:debian-6.0.1a-ia64.netinst.iso (this didn't work, apparently ia64 is for itanium and my machine is definitely not that), so I downloaded: debian-6.0.1a-amd64-netinst.iso, burnt the CD and ran the install. First time through I had a power failure.
Second time through (a complete fresh start - new partition and everything) it went all the way through to completion and reboot.Clicked 'Continue' to reboot and the machine reset as it would normally and the Grub loader started okay, prompted for the "Debian amd64" standard boot image, selected that and the first 6 lines appeared normal, then the messages wizzed by so fast that only superman could read them. Then they stop - here is some of the content...
[3.816673] Kernel panic - not syncing: Attempted to killl init!
Call trace:
get_empty_filp
panic
[code].....
Running it again I get similar stack stuff but it's a different place: [3.541816], [3.427502] And sometimes if I wait for a minute or two it will continue on further but appear to crash again. Hardware details (everything is onboard - no added cards):
G41M-S3
Intel G41 + ICH7 chipsets
CPU: LGA 775 for Intel Core 2 Extreme
[code]......
Is the amd64 the wrong image? Should I try i386? Is it a blip and I should just rerun the entire install again?
View 14 Replies
View Related
Nov 26, 2010
I have installed Ubuntu on my m1530 since 8.04 and currently dual boot Win7 and 10.10. I would like to dual boot on my PC, but I have run into a problem. I am not a pro at Ubuntu, but this problem I can not solve by reading forums like I have in the past.
I realize this is a common problem, but I have noticed people having success.
I have a M4A87TD EVO MB with two Seagate drives in Raid 0. (The raid controller is a SB850 on that MB) I use the raid utility to create the raid drive that Windows7x64 uses. I have 2 partitions and 1 unused space. Partition 1 is Windows, partition 2 is for media, and the remaining unused space is for Ubuntu.
I am running ubuntu-10.10-desktop-amd64 off a Cruzer 16GB flash drive that was installed via Universal-USB-Installer-1.8.1.4.
My problem like so many others is that when I load into Ubuntu, gparted detects two separate hard drives instead of the raid. I read that this is because kpartx is not installed on 10.10. I then went in LiveCD mode and downloaded kpartx from Synaptic Manager. Gparted still reported two drives. I opened terminal and run a few commands with kpartx. I received an error. (Forgive me I didn't write it down, but I believe it said something about a communication error. I will try again later and see.)
Currently I am reflashing the Cruzer with a persistence of 4GB. I am not familiar with this process, but I understand that my LiveCD boot will save information I download to it. I decided to try this method because I was going to install kpartx and reboot to see if this made a difference.
I am looking for any suggestions on a different method or perhaps someone to tell me that the raid controller or some hardware isn't supported. I did install ubuntu-10.10-alternate-amd64 on my flash drive, but fail to get past detecting my CD-ROM drive since it's not plugged in. If this method is viable, I will plug it in. I also watched the ..... video were a guy creates Raid 0 with the alternated CD, but it wasn't a dual boot and didn't use a raid controller from a MB.
View 6 Replies
View Related
Nov 1, 2010
I am running a dual boot system with windows 7 and Ubuntu. Both have run smoothly on my machine (Core 2 quad core on Gigabyte board) I recently upgraded to 10.10 from 10.04 via the update manager within 10.04. Following the upgrade the initial boot failed at the login screen ( i simply got the purple colored screen with a white box in the center of it). Instead of trying to figure out what went wrong, I simply re-installed 10.10 from live CD on top of the upgraded Ubuntu that was failing at the login screen. The live CD install seemed to fix everything for the most part ( I did notice some quickly flashing text right before the login screen. I think it was an error message but it was too fast to read)
My problem now is that I am trying to remove some of my old kernels from the Grub2 boot screen and I cant. I have read many posts on how to remove the old kernels, but my system is proving to be difficult. The old kernels definitely show during boot, but whenever I go into Synaptic they are not there. I have downloaded Ubuntu Tweak, and they do not show in it either. I have read the information at [URL] I went to http://www.fixthecode.com/remove-hug...sts-in-ubuntu/ and thought this would fix my problem but I keep getting an error: "awk: 1: unexpected character 0xe2" when i try to run: "dpkg -l | grep ^ii | grep 2.6.3x-xx | awk -F{print $2} I am running kernel 2.6.35-22 The kernels i want to remove are 2.6.32-23 and 2.6.32-24.
View 7 Replies
View Related
Aug 16, 2010
I have a Redhat Enterprise Linux system and I want to re-make it as Debian. I downloaded the Debian netinst iso but can't seem to make a bootable CD out of it, and I haven't found any adequate explanations anywhere.
I tried burning the iso directly to a disk. i set up the boot order in my BIOS but when I restart the machine it spins the CD drive a few times and then moves on to the hard drive.
I tried expanding the iso into a directory, and then copying all those files into into the "Blank CD-R Disc" on my Gnome Desktop, burnt the CD, and still no boot.
I found some instructions using X3b, but X3b was giving me errors.
View 8 Replies
View Related
Sep 15, 2010
It's been a real battle, but I am getting close.I won't go into all the details of the fight that I have had, but I've almost made it to the finish line. Here is the set up. ASUS Z8PE-D18 mother board 2 CPU, 8 Gig Ram. I recently added an OCZ Agility SSD, defined a raid 1 virtual disk on the 1 terabyte WD HDD drives, which will holds all of my user data, the SSD is for executables.The bios is set to AHCI. Windows 7 installed fine, recognizes the raid VD just fine.
I installed Ubuntu 10.04 by first booting into try and mode, then opening a terminal and issuing a "sudo dmraid -ay" command. Then performing the install. I told it to install the raid components, and told it to let me specify the partitions manually. When setting up the partitions, I told it to use the free space I set aside on the SSD from the Windows 7 install as ext4 and to mount root there. Ubuntu installed just fine, grub2 comes up just fine, and Windows 7 boots with out a hitch, recognizing the mirrored partition as I indicated previously. When I tell grub to boot linux however, it pauses and I get the "no block devices found" message. It will then boot, but it does not recognize the raid array. After Ubuntu starts up I can run "dmraid -ay" and it recognizes the raid array, but shows the two component disks of the raid array as well. It will not allow the component disks to be mounted, but they show up which is annoying. (I can live with that if I have to)
I have fixed a similar problem before by setting up a dmraid script in /etc/initramfs-tools/scripts/local-top ... following the instructions found at the bottom of this blog:[URL].. To recap: My problem is that after grub2 fires up Ubuntu 10.04.1 LTS (Lucid Lynx), it pauses, and I get "no block devices found" It then boots but does not recognize the raid array untill I manually run "dmraid -ay". I've hunted around for what to do but I have not found anything. It may be some timing issue or something, but I am so tired of beating my head against this wall.
View 4 Replies
View Related
Mar 23, 2011
Alright, what I thought would be a simple task has me tied in knots.
I wanted to make a multiboot USB flash drive that I could easily manipulate to switch to various distros easily. My plans were:
1. Partition my 8GB drive to one large first partition (5GB) so that windows could access it. (P.S. GParted didn't partition correctly, needed to use fdisk. THIS MIGHT BE IMPORTANT IN SOLVING THE PROBLEM BECAUSE THERE MIGHT BE A BLOCK ERROR). I then made an extended partition with 5 500MB logical partitions.
2. Install Grub2 to MBR from Ubuntu
3. Expand ISO's of varios distros (Acronis Recovery, Puppy linux, etc.)
to the partitions, and create syslinux.cfg files for each (from the isolinux.cfg files that were already there)
4. Install syslinux to each partition's boot sector
Code:
#syslinux /dev/sdb5...
5. make grub.cfg on /dev/sdb1 chainload each partition.
THE GRAND PROBLEM:
Grub2 loads, but when selecting what I want to boot, I get the error
Boot error
which is syslinux, not grub2. So I know it's chainloading, but syslinux doesn't seem to find ldlinux.sys.
P.S. I'm not asking for other ways to make a multiboot drive, I know I can just direct boot from Grub2, but I want to be able to pass the boot to the boot loaders on the other logical partitions.
View 7 Replies
View Related
Feb 10, 2010
I recently got a netbook and setup as dual boot between win7 starter and 9.10 (64bit). Win 7 starter is not impressive so i want to nuke it and give the space all to my /USR partion. I am comfortable working with Gparted and assume that i can launch using my gparted live usb and delete the windows partion and then resize the /usr partion.
what changes do i need to make w/ Grub2? I would prefer not to see the Grub menu at all and have it load right the main kernel if possible. Also, if this is possible is there a way to get to the Grub menu during boot should i need to select a different kernel?
View 2 Replies
View Related
Feb 15, 2010
After installing karmic with Grub2 I am unable to boot into Archlinux partition. Grub2 has removed the last line of the Archlinux boot stanza! It used to read:-
[Code]....
Following the Grub2 tutorials I have tried editing /etc/grub.d/40_custom as follows:-
[Code]....
But no luck. Only way into Archlinux is to get into the edit shell and manually add the missing line and remove other stuff not needed. I have spent hours trying to resolve this issue and I am fairly p----d off
View 2 Replies
View Related
Jan 9, 2011
I have a Windows Vista-Ubuntu 11.04 dual-boot. However, I have lost the ability to boot Windows Vista. I can select Windows in the GRUB menu, but GRUB says
Quote:
error: symbol not found: 'grub_err_printed_errors'
I have repeatedly searched Google for any help, but have found nothing that applies to my situation. I need Windows because I have an iPod Touch with a tethered jailbreak and can't use it right now.
View 8 Replies
View Related
Jan 21, 2011
For several days I stuck on a problem despite my various searches on the net. I just installed a machine in RC1 Squeeze.
My Partitioning
Disc 1
/ boot RAID 1
/ swap RAID 1 and encrypted
/ RAID 1 and encrypted
[Code]....
View 5 Replies
View Related
Mar 28, 2010
how to use Grub2 to boot Windows XP and Linux.
[code]...
there were no entries in the Grub 2 menu after booting. I don't really understand the numbering of hd0,0 to like sda, but I changed "root (hd1,0)" to "root (hd0,0)" if Windows is on hd0, but after rebooting, I still didn't see it. I read somewhere that Grub2 starts partitions at 1, but wasn't sure that was true because in menu.lst they start with 0 sometimes. know entry-level steps to solve this?
View 3 Replies
View Related
