I have old hard disk with broken DMA. When linux boots, it tries to enable DMA, fails, tries again... It tries to enable DMA several times, then disables DMA and boots. But it tries to enable DMA for nearly 3-4 minutes. How can I say linux to not try to enable DMA for this hard disk? System is installed on another hard disk that works great. Old hard disk is used only for not frequently used data.
View 5 Replies
Im using Fedora 15 and it looks nice, but all time I have a notification "A hard disk is reporting health problems "
I looked at:Disk utility SMART data -> Reallocated sector count have 65555 sectors
I made a test from the HP bios to whole HDD without any error, so I think my disk is good.
The question is how can I disable that notification or all notifications? I know it will not fix the problem but I want to stay in Linux.
after installing Ubuntu on one WD 500 GB hard disk and after making mistake and pasting wrong code into Terminal:my OTHER WD 500 GB hard disk that was also in the system (I guess it was "hd1") - died.The problem must be, I guess, I typed wrong code: "hd1,1" instead of "hd0,0".)500 GB (NTFS) of data was on that other (non-Ubuntu) hard disk, and now I can not access it anymore. While booting, system gives "Hard Disk Error" warning and stops.One again: I installed Ubuntu od one hard disk and at the end of instalation I pasted wrong code for GRUB, giving address of another hard disk. Now that other hard disk has error and will not work
View 3 Replies View RelatedI want to copy hard disk have ubuntu 10.04 and ext4 to 1000 hard disk for new 1000
View 2 Replies View RelatedI have a sata 320 gb with mandriva linux 2009.1 on it.And it is what curently atached to my cpu. It is shown as 'sda' in the partition table.I also have another 40gb hard disk with windows xp installed on it.It is shown as 'hda' in the partition table . Now what i want to do is attach this 40gb hard disk to my pc and configure grub on my 320gb hard disk('sda') so as to boot windows xp(which is residing on the second hard disk,'hda')Can anyone tell me if what im doing is feasible or not? If it is feasible,can anyone suggest me how to get it working. I know i just need to add 2-3 lines to my grub.conf, but dont know what exactly i need to write.
View 3 Replies View RelatedI had a dual boot (windows 7 + debian), both of them installed in my internal hard disk, with the GRUB in it. I have recently installed a second linux distro (mint), but I put it in an external hard disk. Now the GRUB allows me to boot any of the three operating systems, but I need the external disk to do it. It seems that after the mint installation the GRUB is now working from the external disk (if the external disk is not connected, the machine does not boot.) �Is there a way to change the location of the GRUB, to the internal hard disk of my laptop?
View 2 Replies View RelatedI was using Terminal and browsing a directory in my home folder. My "home" directory is located on "/dev/sdb1". When in Terminal I typed "ls" in one of my directories and the output was garbage. The output didn't show the files in the directory. I think it said something like, "input/output error". Unfortunately, I didn't write the exact error down. Instead I rebooted.The hard disk with the problem is:
Code:
$ sudo hdparm -I /dev/sdb
[sudo] password for brian:
[code]...
Debian and debian based distros issue has a issue that has come to make it self aware to me when I was trying to burn a video on my hard drive with braseo and it won't let me burn more than 4.4 gigs to a dvd with 4.7 gigs of free space even a file that is over the 4.4 gig limit by a megabyte with windows i didn't have this problem. One more thing I have 16 gig flash drive and on debian and debian based distros i can only use 13.1 gigs of it but on fedora I can use all 16 gigs.
View 3 Replies View RelatedIf you have a hard disk image (including partition table, multiple partitions,...), is it possible to let Linux treat it as a regular hard disk?
By "regular hard disk" I mean I would like to have the image show up as, for instance, /dev/hdx and its partitions as /dev/hdx1,...
(I know I can mount one of the partitions in the image using "mount -o loop,offset=x ..." but I don't really like this option.)
I installed an OS on the second hard-disk/partition3 (/dev/sdb3; OS was FreeBSD). Added the entry and when i boot: nothing. I choose the OS from grub's menu, the list of choices vanishes, the background image stays, and there it hangs. It hangs until i hit: ctrl+alt+backspace. I have thought: to hell with it, and installed Debian/Lenny. Same problem (OH!).
I also installed the boot-loader to the second disk (/dev/sdb), hit F11 after the BIOS-screen and chosen the second hard-disk to boot from: a similar problem. It hangs, and the keyboard is "dead". I am clueless what to check for (i checked the general culprits, but with UUID its all a bit of a mess. I would say it looks good, but wouldn't bet on it) Anyone ever heard of something like that? Without error message its not easy to use the amazing Google. I do a bit of grub-troubleshooting, usually it works, but usually i get error-messages.
I made two threads about it, in case they contain useful info, here they are:
http://www.linuxquestions.org/questions ... sd-827059/
http://forums.freebsd.org/showthread.php?t=17021
I am trying a network install of debian 6.0 by dumping the contents of a DVD onto my local http server. For some reason the Western Digital 80 GB pata HDD doesn't get detected when I click on 'detect disk', I even tried with a SATA, no luck.
View 7 Replies View RelatedI have an external hard disk for USB port. I formatted it on MS for NTFS system.working fine on MS. But can not write while on Debian. Permission denied. Want to use for both on Debian & MS.
View 1 Replies View RelatedI have a Samsung R430 Notebook with debian 6 installed, Nvidia drivers installed... and i'm having troubles with my system... often freezes when i unmount my Hitachi 500GB USB external hard drive.. i got no response from my machine, even with Ctrl+Alt+F1 to enter console mode and reboot from there, just have to shutdown or disconnect my notebook in the bad way.i dont think that is hardware, cause i have installed Windows 7 as well with dual-boot and no problems so far...
cant attach mi mesagge log at this point because the forum doesnt allow me to do that, but if you want to help me i can send that to your e-mail or something.
how to install from hard disk?
View 2 Replies View RelatedI have a system with Windows installed. Now I got a second hard disk on which I want to install Debian. After installation I have a dual boot system or I have to manually configure GRUB? Thnak you and I'm sorry fo my inexperience.
View 1 Replies View RelatedI am running Debian testing (amd64, xfce) on my box where I have two sata hard disks.
I do not have any raid or fancy stuff; all the OS is on one hard disk and the second is mounted on boot and accessible as simple extra storage that I use for some backups.
Today, for the first time, I started to get some messages during the boot about some process (EMASK and DRDY) on my second hard disk.
The system boots, but I cannot access any more the 3 TB volume which is my second hard hard disk.
I do not know if it is a software of hardware problem (the hard disk are not old at all), so...where should I start from?
Just loaded Squeeze (KDE) onto a partition on my desktop and am a bit alarmed by the disk thrashing thats going on? Damn light on constantly. if I didn't know better I'd think I was using Vista. Is this something to do with 'nepomukservices' that seems to be taking a fair amount of cpu time? Not used to KDE 4 so maybe this is normal.
View 6 Replies View RelatedI've bought a new notebook. The hard drive won't stop spinning down and then spinning up again during load. I don't want HD power saving, so I disabled it within
1. /etc/hdparm.conf
Code: Select all# -B apm setting
apm = 255
# -B apm setting when on battery
apm_battery = 255
It didn't work. I can still hear the HD spin up. It's annoying in a video game because things just suddenly stop for a second.
2. /etc/udev/rules.d/50-hdparm.rules
Code: Select allACTION=="add", SUBSYSTEM=="block", KERNEL=="sda", RUN+="/usr/bin/hdparm -B 255 -S 0 /dev/sda"
This was also every tip I could find during RTFM.
Other specs:
Acer Aspire E5-521G-88A8 Notebook
AMD A8-6410 APU
4 GB RAM
AMD Radeon R5 2 GB VRAM
hdparm model number: ST1000LM024 HN-M101MBB
Debian Jessie
I am running a Debian/Linux "Lenny" dual boot system and when I try to open my WD passport storage device I get: Cannot mount volume. Invalid mount option when attempting to mount the volume "My Passport".
This is the contents of my fstab file:
# /etc/fstab: static file system information.
#
# <file system> <mount point> <type> <options> <dump> <pass>
proc /proc proc defaults 0 0
/dev/sda8 / ext3 errors=remount-ro 0 1
[Code].....
My system currently runs mdadm with three mirrored volumes (4 disks, two mirrored partitions on the first two (a) and (b), entire disks mirrored on the second two (c) and (d)), giving me some redundancy in case of disk failure, which it appears I now have. The root volume is mirrored on sda1 and sdb1, and this morning I noticed a mail from mdadm telling me the two RAIDs on (a) and (b) were degraded. It appears things went a step further and /dev/sda is completely gone.
mdadm has come through, though. The system is still running normally with the mirrored partitions on disk (b). What's got me concerned is that disk (a) is only about a month old and was bought brand new. I'm not at home right now to check the actual hardware, but seeing as the signs are pointing this way, do they necessarily mean the disk has failed? Is there something in the logs I could check that would tell me if, say, the PCI SATA card is playing up instead? I know hard disks fail, but I'm paranoid in case tings get worse as I'm running a reasonably important website on this machine, and just wondering if I should be considering setting up a backup server in case there's a bigger problem here. Edit: Sorry, forgot to say. I'm running Squeeze and it's fully up to date. Hardware is a 1.2GHz Celeron, 512MB RAM, Silicon Image SiI 3114 PCI SATA Controller, 2x 500GB SATA disks (a and b), 2x 1TB SATA disks (c and d).
I am using LVM2 and have shrinked my /home partition and extended my / partition but I'm not sure if I used all the free space when growing my / partition. How can I find out? I prefer using the terminal if there is a graphical way to do this but I would like to know both ways if there are two ways.
View 3 Replies View RelatedI have just install debian-7.7.0-i386 on my home pc. I want to configure samba 4 in my Debian box. How may I create Hard Disk partition of 500 GB for a samba server. The professional way i want.
View 3 Replies View RelatedWhat is the recommended method these days for command line partitioning and formatting for the Terabyte size hard disk.?
It was easy to keep up when your working or have access to hardware for re-purposing, but that has all dried up and my knowledge has been left behind. The problem(s) are with new, recent hardware
Following a crash from a now detectable faulty stick of RAMM, I've lost one of my data hard disks and my fiddling with replacement seems to leave various errors/warnings mainly about GPT not supported and this message is still present despite trying fdisk, cfdisk, gpart, gparted, and(?).
System is an ASUS mobo using SATA drives (root 500Gb: MBR+3 partitions;/, swap, /home), and two 2.4TB with single partitions.
I am not sure if this is the correct section but it has to do with a faulty HD. So, the datacenter confirmed that the HD needs to be changed. They put it back and asked me when they should replace it. I told them to wait a bit.
Since then, one of the VPS hosted in this server is booting on "initramfs"
This is the screen. [URL] ....
fsck is not working.
I've bought a 500GB Seagate hdd.the Current hdd carrying Debian has started showing troubles(and will have to RMA it).Can I Copy Debian to a New Ext4 Partition on the New hardddisk?What is the recommended way to mirror copy(everything)?I've last rescued this way some 4 years back using "dd".
View 10 Replies View RelatedI have a single PC that has two hard disks in it. One is 250GB running Debian linux; the other 1TB running windows. I was switching between the two by going to the BIOS and changing the order of the hard disks to boot from. Both lived happily together in peaceful co-existance. Until....
Lately, I haven't been using Linux, so I decided to convert the 250GB to windows. So I put in the windows install CD, and it all started working fine, but when it came down to setting up a partition, Windows only recognized 130GB (out of the 250GB). I got confused so I decided to re-install linux. Linux recognizes the full 250GB; it recognized that there is a second hard disk running a different OS so the grub gave the option to boot from windows. So after a couple of reboots from both drives I decided to go ahead and install windows on the 250GB. Well again, windows only recognized 130GB, but this time, windows showed me another hard disk again with 130GB capacity. Apparently I stupid enough to proceed so now both hard disks - the 250GB and the 1TB - have capacity of 130GB each. And this is where I'm stuck.
I have tried fdisk, I have tried debug, but for some reason, windows can only recognize 130GB out of the entire disks; linux on the other hand recognizes the full capacity. I also used the seagate disk diagnostic tool (seatools for MS DOS) and it found no errors on either hard disk.
How can I reclaim the full capacity under windows?
My PC configuration is as follows:
CPU: AMD Athlon II 245 X2
RAM: 2GB DDR2
MB: ASUS M2A74-AM
SATA DVD-Writer
WD 320GB SATA HDD.
SATA Controller is in AHCI mode in BIOS.
Partition Table:
1. Pri. (Windows 7 Ultimate)
2. Log. (Data)
3. Log. 15GB free space (want to install Linux in this partition)
I want to install Debian 5.0.4 from DVD. But the installer is not showing any partitions, it says entire hard disk is blank. But I ran 'fdisk -l' in the console, it shows the partitions correctly.
I'm trying to install debian-6.0.2.1 from hard diskand it can't find my iso image wich is on the slackware partition.i downloaded initrd.gz an vmlinuz,added some lines to lilo.conf so that i can boot but then when it searches for the iso image doesn't find it .
View 6 Replies View Relatedmount from the old hdd to the new hdd i mean (Hard disk)
View 2 Replies View RelatedI have been frustrated attempting to get Grub2 to boot a Debian Live system from hard disk. Have set aside a 4gb partition /dev/sda1 to contain the Debian Live and some other recovery tools. I actually have them all working from a 4gb USB stick successfully, but getting it to work on my HDD has proved challenging. On USB, I have PartedMagic, Gparted, Grml, and of course my standard 6.01 Squeeze. I have also managed to get the Debian Live booting from that USB stick. Very slick.
However, I can NOT get Debian Live to boot from my HDD; altho all of the others above boot fine. Have tried it two ways - one using an iSO image, which is how it is done on my USB stick. The other attempt is to copy the entire contents of the ISO to a directory.
Here are my directory structures:
debian_live_gnome_squeeze_i386- contains the following: debian-live-6.0.1-i386-gnome-desktop.iso initrd.gz initrd.img vmlinuz which is how it is laid out on my USB stick debian_live - contains the files from the ISO image The error I get is something like "panic unable to find live filesystem" My grub.cfg snippet for the two methods I have tried - the 2nd menuentry is similar to how it works on the USB stick.
menuentry "Debian 6.01 Live (on /dev/sda1)" {
insmod part_msdos
insmod ext2
set root=(hd0,msdos1)
[code]....
Probly don't really need to get it working since PartedMagic can do almost everything I need for recovery and I can use the USB for reinstall or whatever else.
