tried android usb internet tethering from your android with an usb cable to your laptop. zero configuration, the connection is detected as Enternet Usb and there you go Working 100%, quite simple
View 0 Replies
I am running fully updated Stretch. I am tring to complie a driver for Ralink 5370 USB WiFi dongle. When I do make I get the following error:
Code: Select allmake[1]: Entering directory '/lib/modules/4.2.0-1-686-pae/build'
make[1]: *** No rule to make target 'modules'. Stop.
make[1]: Leaving directory '/lib/modules/4.2.0-1-686-pae/build'
Makefile:356: recipe for target 'LINUX' failed
I have installed build-essentials, linux-headers and linux sources. What I have to install to complete this compile?
i have a notebook where i wont to install andorid SDK, I have a Debian 6, 64bit that work well.After install android sdk, i test installation but i have this
:~/android-sdk-linux_x86/tools$ ./emulator
./emulator: error while loading shared libraries: libstdc++.so.6: cannot open shared object file: No such file or directory
i use comand ldd
:~/android-sdk-linux_x86/tools$ ldd ./emulator
[Code]...
I'm restoring an old TI Silent 700 terminal [URL] ... and have connected it to an RPi running the debian based Jessie release using a serial converter. After learning more than I wanted to about serial settings and support I now have it interfaced and communicating bidirectionally but have one last hurdle - proper support for a single case (uppercase only) terminal in agetty.
With the -U flag on it seems like the the login name is detected as needing conversion because lowercase login names work - but lower case passwords do not and once I get a bash prompt all input comes in as upper case. So the -U agetty flag only seems to apply to login name and is then forgotten (not passed on to login process or bash?) and various settings in stty like iuclc, xcase, iexten don't seem to work.
I'd really like to get this terminal working with native support but I'll also take a kludge of some kind (I've tried a tr pipe for example).
Here is what I think is the relevant portion of my systemd generator:
Code: Select all[Service]
ExecStart=-/sbin/agetty -U 300 %I $TERM
Type=idle
Restart=always
UtmpIdentifier=%I
TTYPath=/dev/%I
[Code] .....
I recently upgraded my HDD to 160 GB ..I actually wanted to exchange the old HDD (40GB) and adjust with the price of the new one..The comp service guy said that the internal HDD could be used as a USB disk if I purchase a CASE for this..I bought a case thro which I attached the old IDE HDD... The LED is on when I connect (The USB cable had 2 leads which I had to connect it in 2 USB slots- Direct in my cabinet (not thru Hub),,, Ubuntu 10.04 is recognizing the disk in "System Info" as "USB - Generic HDD"...But that's it, I am not able to run Gparted or anything...Even in win7 , it said "Installing software for devices" and later on nothing happens...This is not shown in File Manager I would like to know how to format and make it usable..
Also , since HDDs involve some amount of power , is it wise to connect it to another computer, I mean there wont be an overload or spike or something like that?? We have 220 Volt electricity in my country... Aso logically speaking there has to be a limit I mean, you cant keep "chain loading" multiple HDD through USB Hubs ,right!!
Here is a copy of my fstab # /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a
# device; this may be used with UUID= as a more robust way to name devices
[code]...
So I'm running proftpd on an old machine just for my own backup purposes, but I'm running out of space. I was wondering if it would be safe/efficent to set up an additional USB hard drive to the LVM drive that I have now? As in, would it write quick enough (USB 2.0), read quick enough and not corrupt data?
View 1 Replies View RelatedI have an acer timelinex 5830tg notebook. After weeks of frustration, i finally have a linux setup that is stable. Thank god for debian. I don't know why I mess with anything else. Anyway, i'm unable to get my built in laptop speakers to work. I get sound through headphone jack, and I hear sound coming from the built in speakers for a split second when plugging in/unplugging my AC adaptor.Let me know if there is any other output needed, which may assist in this issue. Hopefully someone can help me out.
View 3 Replies View Relatedi'm facing an error 500 internal error and i don't know where to start .... How can i get information about the error in order to fix it ???at /var/log/apache2/error.log i can't find anythingi have virtualmin installed , i searched at/var/log/virtualmin/domainname_error_log but nothing .... where is apache supposed to keep log for 500 errors ?
View 1 Replies View Related I should be able to access xfinitywifi hotspots. /etc/network/interfaces and /etc/wpa_supplicant.conf. I don't want to use NetworkManager for this connection.> iw dev wlan0 scan
BSS 60:02:92:e6:78:0a(on wlan0)
TSF: 1619575398784 usec (18d, 17:52:55)
freq: 2437
beacon interval: 100 TUs
capability: ESS ShortPreamble ShortSlotTime (0x0421)
signal: -65.00 dBm
[code]...
when I try to update my Debian, I have the following internal error:Error message:Fetch failed: W:Failed to fetch [URL] Unable to find expected entry free/binary-i386/Packages in Meta-index file (malformed Release file?), W:Failed to fetch [URL] Unable to find expected entry free/binary-i386/Packages in Meta-index file (malformed Release file?)
, W:Failed to fetch [URL] Unable to find expected entry free/binary-i386/Packages in Meta-index file (malformed Release file?), E:Some index files failed to download, they have been ignored, or old ones used instead.
I've got a Suse 11.2 laptop with a bluetooth Wifi device (recognised and working), and an Android 2.1 smartphone (Motorola Milestone). I would like to connect the two via Wifi. I don't have a Wifi router, I've just used it now and again through hotspots. I normally connect to the internet via a mobile broadband USB dongle.So, I suppose I need to configure my laptop as a Wifi router in order to set up our little private LAN between the two devices. Is that right? If yes, can someone please point me to a relevant howto because I've searched high and low and didn't find anything. :-(If the above is not right, then where should I look, please? Is it possible at all, actually?
View 2 Replies View RelatedI have installed the wireless driver shown in the additional drivers tool but am unable to understand how to set up a wifi hotspot so that i can use internet on my android phonethe guides google returned are a bit too complicated with ip tables and all
View 3 Replies View RelatedI just installed Debian 8 and it doesnt look like my WiFi card is working. Unfortunately I didn't make a note what is the card manufacturer. How would I update WiFi driver?I previously had Windows 7 but I installed Debian over Windows.
View 2 Replies View RelatedMy pc is aser aspire 5735z. I have acer nplify 802.11b/g draft-n wlan
but i can use wifi on debian
what i have to do ?
Do i need driver or firmware?
how can i solve this problem ?
I coach a high school debate team. I would like to take my team paperless... Within the world of debate, any evidence you read is required to be made available for your opponent. Many teams use a third laptop as a viewing laptops. They will make a computer to computer network and make a dropbox on the desktop of the 'viewing' computer.
To save money I would like to be able to use some of these cheap bargain basement netbooks/tablets that are coming out as solely a viewing computer. Most of these cheap machines are running android.So....is it possible to network with an android to share files over wifi?Internet is not an option as it is either banned for use in the round or not available...usually both....
I did a netinstall earlier today (latest version, amd64) on my Dell XPS laptop and ended up with a minimal installation because I couldn't connect to the internet. Now I'm trying to get online without a desktop environment.
I have an Intel Centrino 1030, so I downloaded and installed the firmware [URL].... with a usb, then rebooted. My searches have turned up a lot of instructions involving a utility called iwconfig and wpasuppliant, but these are apparently not installed. I don't really know much about it, but my /etc/network/interfaces file looks rather empty:
Code: Select all# The loopback interface
 auto lo
 iface lo inet loopback
Shouldn't there be something like wlan0 there? The network card does show up with lspci
I often connects my laptop (Asus EEE) to my HTC desire hd with the wifi hotspot. But this doesn't work since yesterday when I upgraded to 11.04. When I connect the laptop to the phone the screen on the laptop goes black with a lot of scrolling text then it freezes.
This worked out of the box without any problems with 10.10.
I have broadcom wireless card in my system. I got the driver from broadcom site. I compiled it against my kernel and the module works fine. How could I automatically load this driver at startup. I followed the instruction found in the driver source README file. But its not working. The steps I followed are as follows:
# load driver
# cp wl.ko /lib/modules/`uname -r`/kernel/drivers/net/wireless
# depmod -a
The same steps I followd in 2.6.26 kernel and it worked fine. Now its not working in my new kernel 2.6.32.For manually loading it I have to remove the ssb driver and the download this one. Otherwise it will not work. So I tried adding ssb to /etc/modprobe.d/blacklistle. But that driver loads during startup. So each time I have to manually unload the ssb driver and insert the new one.
I've been installing multiple versions of ubunutu over years and now I better understand why I faced always problems with wifi configuration on these different baselines : Debian root of course.
Now on Debian 7.4 :
The Broadcom BCM4313 driver is not loaded by default (not free product) for my wifi card. This is stated thru the UNCLAIMED declaration
Code: Select allÂ
sudo lshw -c network
 *-network UNCLAIMED
    description: Network controller
    product: BCM4313 802.11b/g/n Wireless LAN Controller
    vendor: Broadcom Corporation
    physical id: 0
[Code] ...
Unclaimed means : no driver found (no kernel association)
So I installed the driver located in the non-free backports by adding this target into the repository
Code: Select alldeb http://http.debian.net/debian/ wheezy main contrib non-free
and install :
Code: Select allsudo apt-get update && apt-get install firmware-brcm80211
sudo modprobe brcm80211
Check seems OK :
Code: Select allsudo lshw -c network
 *-network
    description: Wireless interface
    product: BCM4313 802.11b/g/n Wireless LAN Controller
    vendor: Broadcom Corporation
    physical id: 0
[Code] ....
I can't connect with wlan0, it doesn't work. I found information here regarding WPA2/PSK wifi configuration on debian : [URL] ....
so I added this setup to my interfaces file an got :
Code: Select allauto lo
iface lo inet loopback
allow-hotplug wlan0
iface wlan0 inet dhcp
 wpa-ssid Hznteam-Datacenter
 # hexadecimal psk is encoded from a plaintext passphrase
 wpa-psk 12345678901234567890123456
It's worth ! no more wifi network are detected and ifconfig gives no ip address allocated :
Code: Select allwlan0   Link encap:Ethernet HWaddr 78:e4:00:4e:49:a3Â
     UP BROADCAST MULTICAST MTU:1500 Metric:1
     RX packets:0 errors:0 dropped:0 overruns:0 frame:0
     TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
     collisions:0 txqueuelen:1000
     RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[Code] ....
In a hp pavilion 15 Notebook PC with Debian 8.1.After two hours or so wifi stops working. Network-manager does not give any indication of failure but some times a yellow question mark.
rfkill list wifi gives:
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
ifconfig gives:
eth0 Link encap:Ethernet HWaddr 8c:dc:d4:7b:c2:0e
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:3994 errors:0 dropped:0 overruns:0 frame:0
TX packets:3661 errors:0 dropped:0 overruns:0 carrier:0
[code]...
I've installed Debian 8.1 on Lenovo G50-80 Touch. Ethernet is OK but the WiFi adapter is disabled. How can I enable it?
Code: Select alluname -a
Linux debianserv 3.16.0-4-amd64 #1 SMP Debian 3.16.7-ckt11-1+deb8u3 (2015-08-04) x86_64 GNU/Linux[code][/code]
[code]lspci -nnk | grep -i net -A2
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 10)
  Subsystem: Lenovo Device [17aa:3821]
  Kernel driver in use: r8169
03:00.0 Network controller [0280]: Qualcomm Atheros Device [168c:0041] (rev 20)
  Subsystem: Lenovo Device [17aa:3545]
I am new to linux and decided to use Debian. I installed it on my laptop and have a few problems.First one is my WIFI.
Laptop type: HP Omen 15
Wifi adapter: Intel Wireless 7260n
rfkill list output:0: hci0: Bluetooth
Soft blocked: yes
Hard blocked: no
So wifi is not displaying
Kernel: 3.16.0-4-amd64
Debian version: 8.4
gui: LXDE
URL....
But they see in rfkill list the adapter.How to make this adapter work?I did this with no result:
nano /etc/modprobe.d/blacklist.conf
in file add:
#Fixing a bug that prevents wifi from working on HP Omen
blacklist acer_wmi
I would like to learn more about Linux, but before experimenting I need a working system. The plan for me is to run this as my native machine with vms on top of it with other OS.
I have a netgear wg111t that is running with ndiswrapper. It has an atheros chipset, but calling it ath0 didn't work.
Heres /etc/network/interface :
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface auto lo
iface lo inet loopback
I have finally weaned my laptop from network manager by setting up my /etc/network/interfaces file. # The loopback network interface auto lo iface lo inet loopback
# The primary network interface allow-hotplug eth0iface eth0 inet dhcp
# Wireless Setup auto wlan0 iface wlan0 inet dhcp wireless-essid linksysn
wireless automatically connects to my home wireless network (linksysn). But suppose I wanted to take this laptop to the coffee house where they have free wifi. I am assuming that my wireless will not automatically connect to any other wifi hotspot except linksysn. So how do i set it up to roam like NM did?
To exploit the guessnet capability, I have configured my WIFI so that ifplugd can auto connect WIFI after boot.The access point is hidden, and I have provided all the required info in my /etc/network/interfaces file
mapping wlan0
script guessnet-ifupdown
map default: office-wifi
[code]....
Are USB WiFi adapters more likely to work in Linux than other WiFi adpaters like PCI cards etc?Im just wondering if they can use a generic USB class driver rather than having to have one for the specific chip set?
View 1 Replies View RelatedAfter to install Debian Sid, i can't to connect to my network. When i launch lsmod, ath9k is present so the module is enabled.I don't use network-manager-gnome, wicd and other, i modify myself /etc/network/interface. But even with this configuration, the wifi does not works.
View 3 Replies View RelatedI've been reading around, but not had much success at all in trying to share the internet connection from my laptop to my phone.all the articles i read refer to earlier versions of Ubuntu and the packages they mention have become obsolete, according to the apt-get tool.im not that new to Linux, but my networking probably isn't up to scratch.if anyone could help me, that would be great, im using Ubuntu 10.04 at the time of writing.
View 2 Replies View RelatedI am having a problem with the driver, I do lspci | grep -i net and this is my driver: Broadcom Corporation BCM4321 802.11a/b/g/n...I have tried this: URL.. (I have debian squeeze) and it created a eth1 interface.I do ip link set eth1 up and after that I do : iwlist scan and it works, but when for example I try iw dev eth1 scan it doesn't work it says nl80211 not found.And when I try to run hostapd (which is my final goal) it also says nl80211 not found.
View 1 Replies View Related
