Debian Configuration :: WiFi Connection Isn't Working After Install?
Mar 27, 2016
I just installed the lastest stable Debian (gnome) today and what I was most afraid just happened: my laptop's wifi isn't working properly, it isn't turning on. This had already hapened on livecd.
In the laptop's chassis leds, the wifi led apears as green. When I click to turn on the wifi, as shown on the picture the button, quickly disappears and appears again not seeming to have any effect at all at turning on the wifi but not showing any error either!
Picture :
What's interesting about the wifi not working is that in the installation process I was able to connect to a wifi hotspot and it connected to the internet fine!
Now after installation was complete and my system did the reboot, I was no longer able to connect to the internet using wifi.
My wireless card is Atheros AR9565 and my LAN card is also Atheros.
Here is an output of lspci and lsmod which may have some leads about the problem.
lspci
Code: Select allquant@debian:~$ lspci
00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller (rev 06)
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06)
00:02.0 VGA compatible controller: Intel Corporation 4th Gen Core Processor Integrated Graphics Controller (rev 06)
00:03.0 Audio device: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller (rev 06)
[Code] ....
Noticed:
1. I installed WiFi radar and I ran this on the terminal:
# sudo ifconfig wlan0 up
View 10 Replies
ADVERTISEMENT
Sep 22, 2015
The situation: The office has a WiFi network on one DSL line, which is used for our VoIP call center, and a wired network for our internal network and the majority of web surfing/traffic . Part of the office must be temperature controlled/monitored - we have a rather nice digital thermometer which is WiFi enabled.I have a Debian Wheezy box with a WiFi card and ethernet connection
What I'm trying to accomplish:Connect wifi enabled thermometer to WiFi network so it can automatically send temp updates (currently I have to do it manually via USB)Have the Wheezy box accept the downloaded file then send it to a back up server in the wired network
Side things that may be useful : Prefer to use wired connection for internet and apt and suchWiFi connection will really just be used for connecting to the thermometer
This [URL] .... topic got me thinking that there might be a way to bring the two networks together, but I don't know if that will wreak havoc on things. I know, the Windows and Mac OS don't like having ethernet and wifi at the same time, might Linux be better for this?
v&n had this to offer in the prior thread [URL] .... which I'll be doing more research on.
View 2 Replies
View Related
Apr 12, 2016
I'm using Debian 8 with GNOME 32bit. I installed a driver with ndiswrapper for my old D-Link DWL-G650M.
If i using the default network manager to connect with a Free wifi the connection works fine. But if the wifi have the password the connection doesn't work.
I. using my phone Android to create the Router-Wifi like this:
SSID: AndroidAP5
Password: BillyBob
Encryption(the one allowed): WPA2 PSK
With network manager gnome is impossible to connect. I changed in setting the password type with WPA2 but the system doesn't connect.
I tried to connect manually and i updated the file /etc/network/interfaces as the follow:
Code: Select allauto wlan0
iface wlan0 inet dhcp
wpa-driver wext
wpa-ssid AndroidAP5
wpa-ap-scan 1
wpa-proto RSN
wpa-pairwise CCMP
wpa-group CCMP
wpa-key-mgmt WPA-PSK
wpa-psk 18[...]
After this I tried to execute the follow command :
Code: Select all/etc/init.d/networking restart
And the system returns:
Code: Select all[ ok ] Restarting networking (via systemctl): networking.service
but nothing else happens. The internet connection doesn't work. The Android phone not detect PC connection IN.
View 3 Replies
View Related
Oct 9, 2015
I have Debian 8.2 with KDE 4.14 and everything runs perfect, except for the internet connection. This problem happens randomly when I turn on my machine. Sometimes when the desktop loads, the connection is already settled.
But sometimes when the desktop loads, the wifi icon is still loading and keeps stuck at "setting network address". Since this problem happens randomly I really don't know what is happening here. My wifi chip is this:
Code: Select all01:00.0 Network controller: Intel Corporation Centrino Wireless-N 130 (rev 34)
This is the problem:
I installed Debian with non-free firmware because of this chip.
View 6 Replies
View Related
Dec 1, 2015
I'm trying to use these cookie cutter rules that I found. But every time I use them, after a few seconds my wifi connection goes dead. The exception was the first time I used then. Which lasted me a couple of minutes.
By dead I mean I can no longer open a webpage or ping google.
iptables -N LOGGING
iptables -A INPUT -j LOGGING
iptables -A OUTPUT -j LOGGING
iptables -A LOGGING -m limit --limit 2/min -j LOG --log-prefix "IPTables-Dropped: " --log-level 4
iptables -A LOGGING -j DROP
View 9 Replies
View Related
Jun 28, 2015
In a hp pavilion 15 Notebook PC with Debian 8.1.After two hours or so wifi stops working. Network-manager does not give any indication of failure but some times a yellow question mark.
rfkill list wifi gives:
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
ifconfig gives:
eth0 Link encap:Ethernet HWaddr 8c:dc:d4:7b:c2:0e
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:3994 errors:0 dropped:0 overruns:0 frame:0
TX packets:3661 errors:0 dropped:0 overruns:0 carrier:0
[code]...
View 9 Replies
View Related
Apr 17, 2016
I am new to linux and decided to use Debian. I installed it on my laptop and have a few problems.First one is my WIFI.
Laptop type: HP Omen 15
Wifi adapter: Intel Wireless 7260n
rfkill list output:0: hci0: Bluetooth
Soft blocked: yes
Hard blocked: no
So wifi is not displaying
Kernel: 3.16.0-4-amd64
Debian version: 8.4
gui: LXDE
URL....
But they see in rfkill list the adapter.How to make this adapter work?I did this with no result:
nano /etc/modprobe.d/blacklist.conf
in file add:
#Fixing a bug that prevents wifi from working on HP Omen
blacklist acer_wmi
I would like to learn more about Linux, but before experimenting I need a working system. The plan for me is to run this as my native machine with vms on top of it with other OS.
View 12 Replies
View Related
Oct 22, 2014
I manage to install debian on my flex 10 (lenovo), but now internet is not working, i can see the network, but even being able to connect to them i can't access the net...
View 14 Replies
View Related
Mar 20, 2011
About an hour ago i did an update on my Debian Squeeze. After the update was completed my LAN connection stopped working.. now i have to connect my computer to my router with a usb cable instead with my ethernet cable.. also, on the network connection, on the wired network section it says that the device(ethernet) has not been managed..
View 1 Replies
View Related
Nov 28, 2015
I've been using Ubuntu and Mint for a few years now, and I want to try Linux on my HP Stream7 Tablet. I was very excited to learn that Debian 8.0 and later has support for 32 bit UEFI on 64 bit Processors and went ahead and installed the multiarch version of 8.2. It works, but I have no GUI (Just a command line) and no WIFI connection. It seems the GUI didn't install and the WiFi card is not supported. I have found a driver for the wifi card but don't know how to install this driver. URL....
View 4 Replies
View Related
May 14, 2010
I have no idea how I managed this, but I am able to connect to the internet but NetworkManager doesn't show any connection. This means that until I kill it, I cannot log in with Pidgin, because it is waiting for a connection.
Do I disable NetworkManager completely or do I try to make it recognize that I am connected to the Internet? If the latter, then how should I go about? (Please let me know which files I need to show you, because I know I've messed around with a couple).
View 2 Replies
View Related
Apr 2, 2011
I have installed Suse 11.4 recently and I'm trying to run the wireless connection and doesn't works.
Details:
card: pro/wireless 2200BG Calexico2
driver installed (as console said) kernel driver:ipw2200
hwinfo:
Code:
linux-4pom:/home/victorplata # hwinfo --netcard
25: PCI 604.0: 0282 WLAN controller
[Created at pci.318]
Unique ID: JNkJ.BmKY+aW7YM0
Parent ID: 6NW+.pbi2aV6ikBD
SysFS ID: /devices/pci0000:00/0000:00:1e.0/0000:06:04.0
SysFS BusID: 0000:06:04.0
Hardware Class: network
Model: "Intel PRO/Wireless 2200BG [Calexico2] Network Connection"
Vendor: pci 0x8086 "Intel Corporation"
I have tried to connect by traditional method with YAST, just recognized one network call "Hotel Riga 228", but doesn't connect. Also I have tried to connect with Network Manager but this application doesn't recognize ANY w. network.
View 6 Replies
View Related
Feb 3, 2010
I just recently installed Ubuntu 9.10 on a dell laptop. My WiFi connection that I've been using on the same computer for years is not working when I log on. However if I run the burnt image cd and choose the option "Use Ubuntu without making any changes to your computer" I am asked if I want install proprietary drivers. If I activate one "Broadcom STA" I can connect to the wireless connection in my house. When I am using the version installed on my laptop it doesn't ask me if I want to install the drivers and it doesn't even find them when I go to hardware drivers under system. So to sum it up I can get connection when I run Ubuntu from the cd but not when I run the Ubuntu on my laptop.
View 3 Replies
View Related
Feb 22, 2016
I should be able to access xfinitywifi hotspots. /etc/network/interfaces and /etc/wpa_supplicant.conf. I don't want to use NetworkManager for this connection.> iw dev wlan0 scan
BSS 60:02:92:e6:78:0a(on wlan0)
TSF: 1619575398784 usec (18d, 17:52:55)
freq: 2437
beacon interval: 100 TUs
capability: ESS ShortPreamble ShortSlotTime (0x0421)
signal: -65.00 dBm
[code]...
View 0 Replies
View Related
Apr 15, 2011
1 linksys router: gets the net from PPPOE and give the network DHCP. The router IP is 192.168.1.1. 1 windows laptop that work wireless and wired. 1 debian desktop that work wired and not working wireless. THe problem with the debian desktop is like this: I have a TP-Link TL-WN321G installed and found by lsusb command. I make a wireless connection WPA Personal (just like the router settings) it says i am connected to the wl network but no internet connection. the route command give me this:
[code]....
I tryed with wicd who said that the connection is WEP (and it's not, it is setup to WPA on the router and the network-manager conncetion) and when i try to connect i get bad password. I tryed with network-manager uninstalled and no chance.
View 4 Replies
View Related
Jul 18, 2010
My pc is aser aspire 5735z. I have acer nplify 802.11b/g draft-n wlan
but i can use wifi on debian
what i have to do ?
Do i need driver or firmware?
how can i solve this problem ?
View 5 Replies
View Related
Jan 7, 2014
I did a netinstall earlier today (latest version, amd64) on my Dell XPS laptop and ended up with a minimal installation because I couldn't connect to the internet. Now I'm trying to get online without a desktop environment.
I have an Intel Centrino 1030, so I downloaded and installed the firmware [URL].... with a usb, then rebooted. My searches have turned up a lot of instructions involving a utility called iwconfig and wpasuppliant, but these are apparently not installed. I don't really know much about it, but my /etc/network/interfaces file looks rather empty:
Code: Select all# The loopback interface
auto lo
iface lo inet loopback
Shouldn't there be something like wlan0 there? The network card does show up with lspci
View 14 Replies
View Related
Apr 8, 2014
I've been installing multiple versions of ubunutu over years and now I better understand why I faced always problems with wifi configuration on these different baselines : Debian root of course.
Now on Debian 7.4 :
The Broadcom BCM4313 driver is not loaded by default (not free product) for my wifi card. This is stated thru the UNCLAIMED declaration
Code: Select all
sudo lshw -c network
*-network UNCLAIMED
description: Network controller
product: BCM4313 802.11b/g/n Wireless LAN Controller
vendor: Broadcom Corporation
physical id: 0
[Code] ...
Unclaimed means : no driver found (no kernel association)
So I installed the driver located in the non-free backports by adding this target into the repository
Code: Select alldeb http://http.debian.net/debian/ wheezy main contrib non-free
and install :
Code: Select allsudo apt-get update && apt-get install firmware-brcm80211
sudo modprobe brcm80211
Check seems OK :
Code: Select allsudo lshw -c network
*-network
description: Wireless interface
product: BCM4313 802.11b/g/n Wireless LAN Controller
vendor: Broadcom Corporation
physical id: 0
[Code] ....
I can't connect with wlan0, it doesn't work. I found information here regarding WPA2/PSK wifi configuration on debian : [URL] ....
so I added this setup to my interfaces file an got :
Code: Select allauto lo
iface lo inet loopback
allow-hotplug wlan0
iface wlan0 inet dhcp
wpa-ssid Hznteam-Datacenter
# hexadecimal psk is encoded from a plaintext passphrase
wpa-psk 12345678901234567890123456
It's worth ! no more wifi network are detected and ifconfig gives no ip address allocated :
Code: Select allwlan0 Link encap:Ethernet HWaddr 78:e4:00:4e:49:a3
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[Code] ....
View 7 Replies
View Related
Sep 5, 2015
I've installed Debian 8.1 on Lenovo G50-80 Touch. Ethernet is OK but the WiFi adapter is disabled. How can I enable it?
Code: Select alluname -a
Linux debianserv 3.16.0-4-amd64 #1 SMP Debian 3.16.7-ckt11-1+deb8u3 (2015-08-04) x86_64 GNU/Linux[code][/code]
[code]lspci -nnk | grep -i net -A2
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 10)
Subsystem: Lenovo Device [17aa:3821]
Kernel driver in use: r8169
03:00.0 Network controller [0280]: Qualcomm Atheros Device [168c:0041] (rev 20)
Subsystem: Lenovo Device [17aa:3545]
View 4 Replies
View Related
Jun 16, 2010
I have a netgear wg111t that is running with ndiswrapper. It has an atheros chipset, but calling it ath0 didn't work.
Heres /etc/network/interface :
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface auto lo
iface lo inet loopback
View 6 Replies
View Related
Aug 23, 2010
I have finally weaned my laptop from network manager by setting up my /etc/network/interfaces file. # The loopback network interface auto lo iface lo inet loopback
# The primary network interface allow-hotplug eth0iface eth0 inet dhcp
# Wireless Setup auto wlan0 iface wlan0 inet dhcp wireless-essid linksysn
wireless automatically connects to my home wireless network (linksysn). But suppose I wanted to take this laptop to the coffee house where they have free wifi. I am assuming that my wireless will not automatically connect to any other wifi hotspot except linksysn. So how do i set it up to roam like NM did?
View 5 Replies
View Related
Aug 30, 2010
To exploit the guessnet capability, I have configured my WIFI so that ifplugd can auto connect WIFI after boot.The access point is hidden, and I have provided all the required info in my /etc/network/interfaces file
mapping wlan0
script guessnet-ifupdown
map default: office-wifi
[code]....
View 1 Replies
View Related
Nov 13, 2010
Are USB WiFi adapters more likely to work in Linux than other WiFi adpaters like PCI cards etc?Im just wondering if they can use a generic USB class driver rather than having to have one for the specific chip set?
View 1 Replies
View Related
Aug 5, 2011
After to install Debian Sid, i can't to connect to my network. When i launch lsmod, ath9k is present so the module is enabled.I don't use network-manager-gnome, wicd and other, i modify myself /etc/network/interface. But even with this configuration, the wifi does not works.
View 3 Replies
View Related
Aug 21, 2010
I'm using Debian-Squeeze, and the command "uname -a" results in "Linux debian 2.6.32-5-amd64 #1 SMP Sat Jul 24 01:47:24 UTC 2010 x86_64 GNU/Linux". The desktop environment is Gnome 2.30.2.
My problem is wireless connection causes the system to crash. Here is the detail: my university uses a WiFi service that we have to enter our ID and password in a certain web page in the browser to get access to the Internet, while the WiFi signal is automatically picked up. My laptop crashes each time I connecting to such wireless network. But back home, when connecting to my own WiFi, everything is all right.
As the only thing I can do when such crash happens is to press the power button to force the computer to shut down, I've gathered no more information till now.
Does anyone know what's wrong and how to fix it?
View 4 Replies
View Related
May 20, 2015
Using a USB ISO, I recently installed Debian 8.0 Jessie (64-bit, Xfce DE) to a new computer. I usually lose my Wifi connection after 1-3 minutes when donwloading/uploading at around max. speed 4 Mbps/512 kbps. Sometimes it will last 15+ minutes.
When lightly browsing it can usually stay connected for 15-30 minutes. I have to disable and enable Wifi using NetworkManager to connect again. If I remember correctly, there were problems with the Wifi connection even during the installation of Debian.
This Wifi USB adapter works fine on my old computer with Debian 7.7 (32-bit). No problems with the Wifi connection yesterday on my old computer during 10+ hours of activity.
This Wifi adapter also works fine on this new computer when I boot from a live USB (Rescatux 0.30.2) downloading and uploading at max. speed for 1+ hour.
I already tried some suggestions I found online, but they didn't work:
* changing Wifi channels between 1, 6, 11 in my router settings
* changing WPA-WPA2 to WPA2 in my router settings
* ignore IPv6 in NetworkManager
* change probe_wait_ms from 500 ms to higher value by adding Code: Select alloptions mac80211 probe_wait_ms=1000 or Code: Select alloptions mac80211 probe_wait_ms=3000 to /etc/modprobe.d/mac80211.conf and rebooting
* disable Power Management for Wifi adapter (not supported)
* ...
I can also post the output of commands from Rescatux or my old computer if needed.
Output of commands on Debian 8.0 64-bit (I edited out some info, MAC, ...; not sure if that is important):
Code: Select alluname -a
Linux d8lnx 3.16.0-4-amd64 #1 SMP Debian 3.16.7-ckt9-2 (2015-04-13) x86_64 GNU/Linux
Code: Select alldmesg
...
[ 291.292408] ieee80211 phy0: wlan0: No probe response from AP XX:XX:XX:XX:XX:XX after 3000ms, disconnecting.
[ 291.459825] cfg80211: Calling CRDA to update world regulatory domain
[ 291.462030] cfg80211: World regulatory domain updated:
[ 291.462033] cfg80211: DFS Master region: unset
[CODE]....
View 14 Replies
View Related
Aug 21, 2015
A friend gave me an HP Mini 110 that I can actually use in some situations. I installed Debian 8 with LXDE. It runs well except for the expected lack of driver for the Broadcom 4312 wireless chip. I installed wl using the method shown at [URL] ....
It works fine except that it takes very long to set up WiFi at boot (1 min 30 sec or more every boot--this is a rather frail Atom processor) and the WiFi reception seems poor (65% from an excellent router at 25 feet).
I'm thinking of getting a Panda 300Mbps Wireless N USB Adapter (reportedly using the Ralink RT5372 chipset) and removing the Broadcom driver. I have 2 questions:
1. Could I expect the Panda not to slow my boot time so much? I'm not knowledgeable enough to tell whether there is stable kernel support of this device, although the manufacturer says repeatedly that it works with most Linux distributions.
2. To remove wl is Code: Select allmodprobe -r wl the correct approach?
View 4 Replies
View Related
Aug 27, 2015
I've been using Debian for about 6-7 months now. I've had a bit of a major networking problem for the past 4 months or so that I've been trying to fix - specifically, it started when I upgraded to Jessie. I can connect to wifi just fine, and sometimes I can even use the internet for brief periods of time (exceedingly rarely). Then... nothing. No network access, period. I can't ping any outside servers, I can't ping other computers on my network, and I can't even ping my router. Pages I try to load just stay "connecting" for all eternity, network printing fails, and so on.
So after four months of searching online (I've read through way more wireless documentation than I care to say), I finally gave up and admitted that maybe I screwed something up during upgrade to Jessie (as a matter of fact, I did, I had to do the upgrade in two increments [somehow] because my root partition was too tiny by mistake) and I did a clean install. Since I had /home on a separate partition, I was able to keep all my user files, but all settings regarding networking were wiped. So after installing firmware-iwlwifi so I can use my wireless card, I tried connecting to wireless! Success! Then I tried connecting to the internet... success! Briefly. The next morning I tried using the internet again, and it failed in exactly the same pattern as before.
I don't know much about what's going on here, but here's what I do have available:
I do have to use firmware-iwlwifi, which I installed by doing apt-get install firmware-iwlwifi. I don't think it's an issue with the wireless card itself (hardware-wise), the laptop dual-boots Windows 7 (that I never use anymore), and Windows 7 is able to connect to the internet just fine. Connecting directly to my router by ethernet cable works fine, I have perfect internet/network access then.
I can confirm that my laptop is receiving an IP address and that it is using ARP correctly to get the MAC address of my router (I confirmed this by doing the arp command, it has the MAC address correct, I checked from another computer with my router's config page) All other computers on my network work perfectly with my router. To confirm the router/its configuration isn't at fault, I did a full factory reset of the router, but to no avail.
Out of curiosity I tried installing Wireshark (using an ethernet cable to download it) to monitor what happens when I try to access a webpage. I'm no expert on networking, but I noticed something out place when I compare a capture from the affected computer to a capture from one operating normally - there are a lot of STP packets showing up. I did some checking around, it looks like STP is involved in bridging and more complex networking setups (involving switches, for example)... but it shouldn't be found on a home network, especially where there's no bridging whatsoever. These STP packets don't show up on packet captures done from any other computer. I've attached a packet capture from the affected computer here, since the forums won't let me attach a .pcapng file.
Here's the output from a few commands I ran during past troubleshooting sessions:
Code: Select allsudo ifconfig
eth0 Link encap:Ethernet HWaddr e0:db:55:b5:fe:06
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:12455 errors:0 dropped:0 overruns:0 frame:0
TX packets:7781 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
[Code] ....
View 5 Replies
View Related
Oct 22, 2015
I am running fully updated Stretch. I am tring to complie a driver for Ralink 5370 USB WiFi dongle. When I do make I get the following error:
Code: Select allmake[1]: Entering directory '/lib/modules/4.2.0-1-686-pae/build'
make[1]: *** No rule to make target 'modules'. Stop.
make[1]: Leaving directory '/lib/modules/4.2.0-1-686-pae/build'
Makefile:356: recipe for target 'LINUX' failed
I have installed build-essentials, linux-headers and linux sources. What I have to install to complete this compile?
View 3 Replies
View Related
Feb 25, 2016
how to use 5GHz on my laptop? It's Lenovo ideapad Y580, router enabled dual band. However, these are results from terminal:
iwconfig wlan0
wlan0 IEEE 802.11bgn ESSID:"BTHub..."
Mode:Managed Frequency:2.437 GHz Access Point: 00:E9:...
Bit Rate=130 Mb/s Tx-Power=15 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=70/70 Signal level=-36 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:67 Invalid misc:252 Missed beacon:0
View 0 Replies
View Related