Debian Configuration :: Uupdate Lost Raids?
Feb 14, 2010
I have recently installed debian on to a system that I built as a media server. It has 4 1TB HDDs in the machine and each drive was partitions as follows:
10 MB /boot -md0
1 GB swap -md1
remaining / -md2
I had the /boot running as a raid 1 so i could make backups and the swap was running raid 0 for 4 GB of swap striped. The rest was all setup as a raid 5.I setup the system using mdadm and all worked out perfect. The system worked fine on reboot and all the raids showed no degration on them. However when the debian update icon came up on the screen came up I opened it and it said I needed some updates which was fine. So it did the updates to my system. system was still fine.
View 4 Replies
ADVERTISEMENT
Aug 11, 2011
Some problems keep bothering me and dont let me use my debian sqeeze with joy.Im in network with no DHCP on. When installing i didnt configure my eth network card.After each restart i need to configure manually my eth because it loses it.
View 7 Replies
View Related
Oct 3, 2015
Debian Testing, updated daily, running Gnome.
A week ago, a new router was installed at the office and now my system "loses" the networks printers and forces me to manually select them within Cups various times a day to be able to print. The issue was not present when the old router was in place, and all my colleagues can print without problems using their Windows machines.
This only affects printing, for Simple Scan can always communicate with the printers without problems.
The printers are two basic Epson L355 (those with ink tanks) and the "official" driver (from Open Printing) has been working perfectly since I installed Debian. The whole Cups and Avahi stack is installed, and I even added system-config-printer this week to make sure that I was not missing a package.
Because the only variable that changed is the router, there has to be something there messing with my Cups or Avahi configuration.
Note that the new router had a "vanilla" installation, where no advanced settings were touched. All connected devices (computers, mobile phones, printers, etc.) are given new IP address through DHCP every day.
Where should I start? I have already deleted and added the printers within Cups several times during the week, and the problem persists. Is the router renewing the address more often than the old one did? Can this "refresh" be delayed? Should Avahi monitor devices more often?
I guess that I could configure the router and give static IP addresses to the printers, but such a setting was not present in the old router and my computer could locate the printers without problems.
View 3 Replies
View Related
Jan 15, 2010
I recently purchased a Wacom Bamboo CTH-460 and have had endless frustration trying to get it to work.
I started by getting the latest stable source from the Linux Wacom project and trying to compile the drivers and kernel modules from source and installing them, though nothing ever seemed to work. If I do lsmod it shows that the wacom kernel module is loaded but when I do more /proc/bus/usb/devices I end up with this:
And no matter what I try it always says Driver=(none). So that means none of the /dev/input events are getting any data from the tablet, which means there's no way for it to do anything with X. So that is the step I am stuck at.
After some time I came to suspect that perhaps the CTH-460 is too new to be supported, and am now trying to compile drivers from the lastest development source realeased on 12-30-09. It said there was support for 5 new Bamboo tablets. However when I try to make the driver I run into this error:
I'm not sure if that is just an error in the make script or not, and if it is, why no one else has said anything about it.
Maybe I'm going about this all wrong, do I even need a new kernel driver for my tablet model? Do I only need an Xorg driver? What modules and drivers need to be in place before I should at least get the tablet tied to an input event?
View 4 Replies
View Related
Jul 14, 2010
after a reboot of my Lenny system, the default gateway will lost. Then i must try "networking restart" and the gatway will be set
my interfaces looks :
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
[Code].....
View 1 Replies
View Related
Oct 29, 2010
When I make a vpn connection to an openvpn server, I loose the internet connection.
The VPN works all right.
Server config (extract)
Client config
Client route without the VPN connection
client route with VPN connected (internet lost)
Is there anything I can do to the push rule of the servers's config file?
View 1 Replies
View Related
Dec 28, 2015
Had an issue on one of my Debian stable servers the other day. After doing apt-get upgrade I was prompted to do autotoremove.
It wanted to autotremove
Code: Select allStart-Date: 2015-12-21Â 16:25:05
Commandline: apt-get autoremove
Remove: sendmail-cf:amd64 (8.14.4-8), exim4-config:amd64 (4.84-8), sendmail-base:amd64 (8.14.4-8)
End-Date: 2015-12-21Â 16:25:07
After doing this I rebooted my server (a few days later). After rebooting I had no ipv4. I tried statically assigning IP addresses to no avail. Ran ifconfig eth0 down/up which got me nowhere. Eventually decided to ask "Okay, what changed". Started installing packages that were autoremoved. Had to install from the apt cache using dpkg. First one I tried was sendmail-base. Then did ifconfig eth0 down/up, which gave me networking back.
I have checked the dependencies for sendmail-base and I see nothing that would relate to networking, so I'm really confused on why this happened. I had backups of the server so I went a week back and noticed sendmail-base was installed at that time. So I went a day back, where sendmail-base wasn't installed, and installed it. Sure enough it brought back networking. I'm just stating this because it is more proof that sendmail-base was the missing component.
View 0 Replies
View Related
Apr 12, 2016
I have lost my password for my root and for my user account.
Code: Select alluser@debian:~$ su
Password:
su: Authentication failure
user@debian:~$ su
Password:
su: Authentication failure
user@debian:~$ su
I have just installed a gust debian 8 on debian 8 host in virtualbox, and when i wonted too login as su/root on the host there where no login possible, is there a way to regain the root password for the host?
View 2 Replies
View Related
Jul 8, 2011
I tried to edit my xorg.conf to try and encourage Debian to handle my joypad better (stop recognising it as a mouse). However, it didn't work and i couldn't get back into X.So, i entered recovery mode and deleted the contents of xorg.conf,got back into X and then edited xorg.conf back to how it was.Right so far so good.Yet, now i cannot use the backlash key in keyboard shortcuts. I have a number of shortcuts set up to incorporate this key and they no longer work, neither in GNOME nor Openbox
View 2 Replies
View Related
May 9, 2011
Hi,I'm using a Dell Lattitude D620 laptop. I just installed the latest kernel 2.6.38 in my Squeeze amd64 :
Output of uname -r
2.6.38-bpo.2-amd64
Now I'm running on new kernel,everything seems fine except my wifi ( now I'm connected through ethernet ). Before I do the process with the guide in http://wiki.debian.org/wl to activate my wifi,I'd like to ask for some advice here,is this latest kernel support my wifi card? If yes,how to activate it?
Output of lspci :
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03)
[code]....
View 4 Replies
View Related
Mar 3, 2011
I was playing with my debian server when something went totally wrong while i was editing something on my network interface,i removed those crap that i wrote and left the network interface configuration as it was
Like for example after re-editing my network interface,it was like :
As i did a network restart, i get this error saying :
There is already a pid file /var/run/dhclient.eth0.pid with pid 2802 killed old client process, removed PID file.
What is this error and how can i fix it,because every time im re booting my server i lost my network config.
View 1 Replies
View Related
Aug 7, 2010
I am currently running a system that has Windows 7 and Ubuntu 10.04 running on separate raids. Here is an outline of my system.
Raid 1:
OS: Windows 7
Raid Controller: Intel ICH5R
Raid Type: 1 (Mirror)
# of Disks: 2
Disk Type: Sata HDDs
[Code]...
I would have liked to put both raids on the same controller but Windows XP/Vista/7 will sometimes throw up a blue screen when a single controller handles two independent raids. My setup prevents this issue. The good news is that I was able to get both of the raids up and running without much difficulty.
Right now I can only access my Ubuntu raid by going into the bios on startup and changing the boot order. Needless to say, this has become somewhat tiresome. It would be much simpler if I could use Grub2 to select between operating systems upon boot. While I know the process of installing Grub2 on a dual-booted system is relatively painless, I imagine my setup would be more complex.
View 1 Replies
View Related
Oct 7, 2010
Fake raid hard drives are becoming more common and I am wondering how to set them up. This is what I have been told, and you are welcome to disagree (as long as we can agree to disagree).From what I have seen and heard it appears to me that to set up a fake raid in Linux you partition the separate volumes and format them, but when you install your operating system you have to go into fstab and merge the separate volumes into the root partition.
View 5 Replies
View Related
Aug 15, 2011
Having alot of trouble searching for answers as it just pulls up irrelivnent info.I have 2 HDD's id like to show as one virtual disk or mount them both to one folder, but without raid so if i dies the other will be ok. Is this something i can achieve with symbolic links or JBOD raids? or other options ^_^
View 1 Replies
View Related
Jun 3, 2011
uBuntu 10.10, Simple Backup My backup stopped working at certain date. Went back in "Simple backup-Configuration", it says, there is no configuration. What might cause trouble like this? Should I seek for more secure back up tool?
View 2 Replies
View Related
Sep 16, 2009
Google brought me no love on this one, tried searching here with little luck as well. So I'm hoping somebody vastly more experienced than I can shed some light on my plight.
The situation:
I have a CentOS 5.3 x64 server running the latest cPanel which works fantastic. I issued a graceful reboot and the server came back up (according to the DC) just fine to a login prompt. Apparently the system lost all of its IP address configuration. Primary IP, secondary IP's gateway, you name it and it was gone. Now my secondary IP's were showing in cPanel after I had the DC re-enter my main IP address/gateway. But listed as not active due to the fact that they were not anywhere to be attached to the interface. i.e. eth0:1 eth0:2 etc and so on.
I have no idea where to begin looking for this problem and am afraid to reboot it again (at least until I get my lantronix spider up there). I've never experienced this with any of my other CentOS/cPanel servers either. All similar configurations CentOS 5.3 x64, latest cPanel as well. My hardware is all Supermicro gear as well and has been solid in the past.
Maybe I'm just missing something, granted I've only been managing Linux based servers for about two years now. This is actually the first real problem I've ran into on any Linux distro, they are normally pretty solid. So I assume it's a configuration error on my part somewhere.
View 2 Replies
View Related
Sep 10, 2010
After running a large update and rebooting a few weeks ago, I found that my internet connection had stopped working. My internal network still worked fine though, so it I know it's not the card itself or its configuration. After a bit of trial and error I discovered that simply running dhclient brings the connection up again, so it appears that something is interfering with the initial dhcp update to my ISP (or something like that; I'm no expert in this area. ) My usual policy in cases like this is to wait through two or three updates in the hopes that it's just a temporary problem, but it's been a while now and subsequent updates haven't fixed it.
I've tried looking around, but I can't come up with search criteria specific enough to narrow it down to my specific situation. I'm not even sure where to begin looking to diagnose the problem, nor do I know which package update(s) could've affected it. I'm not sure what might be useful, but here's the relevant entry in /etc/network/interfaces. I have it configured with a static internal address, with my router as the gateway.
Code:
# The primary network interface
mapping eth0
script grep
map eth0
[code].....
View 7 Replies
View Related
Sep 7, 2010
Recently installed some application which screwed the default common-passwd file and has put some restrictions on the passwords which I could setThe present file looks like this
Code:
#password required pam_passwdqc.so min=disabled,8,8,8,8 passphrase=0 enforce=users
password required pam_passwdqc.so min=1,0,0,0,0 passphrase=0 enforce=none random=0
[code]...
View 1 Replies
View Related
Nov 14, 2010
I have installed the current Nvidia driver(s) for my video card:
nvidia-gfxGO2-kmp-desktop 260.19.12_k2.6.34.0_12-24.1
x11-video-nvidiaGO2 260.19.12-25.1
nvidia-settings 256.35.0.pm. 1.1
xorg-x11-driver-vido-nouveau 0.0.15_20100401_bfb95cc-1.10
libXNVCtrl 256.35-0.pm.2.1
Now my problem is everytime I save the configuration for
- the open GL settings
- the anti aliasing settings
- the powermizing settings
with the GUI-programm NVIDIA X Server Settings under GNOME
Every setting is lost completely after a restart of my system and the defaults are reset even if i save the configuration in the menu nvidia-settings configuration of the GUI-programm NVIDIA X Server Settings. Is there a possibility to SAVE the settings? They should stay after a reboot.
I think this is a issue very spread under several Linux distributions. I can't understand the source of the mistake or bug.
View 9 Replies
View Related
Jun 13, 2010
I have accidentally started the recovery OS of my netbook, and messed-up grub. I can start the Netbook from a live CD, but I do not manage to restore grub to anything useful. Below the outcome of the Boot Info Script I have found in the forum:
Code:
Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ==============================
=> Grub 0.97 is installed in the MBR of /dev/sda and looks on the same drive
in partition #5 for /boot/grub/stage2 and /boot/grub/menu.lst.
=> Syslinux is installed in the MBR of /dev/sdb
[code]....
View 9 Replies
View Related
Nov 18, 2010
I am having no luck configuring ProFTPd on a Debian Lenny production server we use to host our MySQL databases and a few websites. I had originally set it up so I could login and manage our internal sites, but I have the need to allow a few clients in to access their sites that we host. I am trying to root the users in their site directory, which would be "/sites/www.whatever.com/".
It just hit me while typing this. Is it possible to create a user without a shell to prevent login via SSH and set the home folder to /sites/whatever instead of /home/username? That would allow me to continue operating with my current configuration and root them in their site while preventing SSH logins.
View 6 Replies
View Related
Jul 20, 2011
i have a HP MSA 2312fc SAN with 2 LUNs configured. The first LUN (LUN ID 1) is correctly connected to the system, but when i connect the second LUN (LUN ID 30), i find in the syslog this message: multipathd: 8:64: size 6835937472, expected 5267578112. Discard
Here is the multipath.conf
[Code]....
So I correctly see the two luns, but multipath doesn't create the relative devices. Under /dev/mapper I see: control mpath0 mpath0-part1 mpath0-part1 is the first lun, the one I mounted in a directory under filesystem. I can't find the device for the second lun
View 1 Replies
View Related
Apr 5, 2010
I am *finally* getting around to rebuilding my file-sharing computer. I'll be sharing files with both Linux and Windoze machines. It's a home network, so there's nothing fancy needed. I know I have to tweak my smb.conf file until I'm satisfied with the features and security. I'm using SWAT and I'm starting with a bare-bones conf file. It's not secure but I can see the server and selected files/directories from my other Linux box.
My really dumb question is, do I have to reboot both the server and the client machines every time I change the SAMBA configuration? I thought I just had to stop and restart the SAMBA service in the SWAT software - but then the server disappears from my client. It looks like I need to reboot both machines for the client to see the server.
View 1 Replies
View Related
Aug 23, 2011
I have some errors when run the mount -all command: mount: wrong fs type, bad option, bad superblock on /dev/sdc5, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Failed to open /proc/filesystems: No such file or directory
[Code]..
View 14 Replies
View Related
Aug 3, 2011
I have a PC104 running debian. I have 3 hard drives (in addition to the one booting) mounted in fstab by UUID. I use the options defaults,error=remount-ro. However, this means that when I boot with the hard drives not attached, I have to press Ctrl-D to bypass when the boot discovers the drives are missing. Is there a timeout commandoption I can add to fstab so that it automatically continues booting even if the hard drives are not attached? I could not find anything on a timeout command. (I tried adding timeout=1000 but no-random guess)
View 5 Replies
View Related
Mar 19, 2011
A week ago I opened this thread viewtopic.php?f=17&t=61580 in "Board index ‹ Help ‹ Installation" and asked for a moderator to move this to here. Because it hasnt happened up to know, I am reopening the thread here. It would be reeeeally great if somebody could help me with my problem!
I own two computers, one netbook and one laptop. I want to boot my netbook as a diskless client via PXE.I set up a dhcp-, tftp and nfs-server on my laptop but when i boot my netbook, the follwoing messages are displayed:(to make it more clear, i uploaded the whole output and shortened the output below)
[Code]...
View 1 Replies
View Related
Jul 31, 2011
I am using Squessze and Gnome. When I try to use the gui System>Administration>Network or Users and Groups I get the error The configuration could not be loaded. You are not allowed to access the system configuration.Everything was working before. I read around a bit. In some cases,it was caused by mismatching group and password files after using the gui. I do not know how to check if they are matching. Of course I do not know for sure that is the problem in my case.
View 14 Replies
View Related
Mar 5, 2010
I use apache2 with virtual host and I 've a solution of Webftp who run on it. This solution send automatically email when a new client register himself. In the header of the mail I look this "Content-type: text/html". But when I look this mail with Outlook 2007 the accents are bad coding.It's a script who generate this Html content email.
View 1 Replies
View Related
Jun 17, 2010
I am working on a Debian 2.6.26-19 Distribution with exim4 as MTA. After a system restart a problem occurred with delivering emails to local addresses. These local addresses use a 1and1 mailserver for email. The MX records for the local domain are set correctly but exim does not use a DNS lookup for these addresses because it identifies them as local addresses. I figured this out by executing the exim4 -d -bt command. The dns lookup part of the result looks like this (I replaced the actual address with placeholders):
[Code]....
The eventual result of the exim4 -d -bt command is: [user]@[domain.ext] is undeliverable: Unrouteable address How can I make sure, that exim4 makes a DNS lookup for the local addresses instead of skipping it? I know that I have to edit a exim4 configuration file, but I could not figure out which and how.
View 1 Replies
View Related
Jul 6, 2010
I have a set of vm's with stable, testing, and sid to keep track of how things are going. When I did an apt-get dist-upgrade with squeeze last week, things seemed to OK (350 package updates) until the end. It didn't seem to like and / or was confused by a kernel dependency.
I am not too concerned yet. Because these are in vm's, I do a snapshot before any significant change. I can futz around with impunity because I have that backup.
I re-booted, and tried the apt-get dist-upgrade again with same results. I think I also tried apt-get -f install.
So I reverted to the snapshot, and will simply try again in the future. I recall that with lenny as testing, the font-desktop was really screwed up for about a period of 6 weeks.
However, just in case someone else runs into this:
1) a re-boot worked, but the failure of apt-get made me nervous enough to revert.
2) waiting for corrections has seemed to work in the past (with a single exception with a 4-disk SCSI software RAID10 update that failed to re-boot lenny successfully after what seemed to be a minor update -- that was on a real system, not a vm. I haven't gotten back to look at that.)
View 14 Replies
View Related
