How does the 'testing' version of Debian stabilize? I mean, the updates from upstream are very frequent, so if the Debian maintainers upgrade a package till the very end (for e.g if they just upgrade to 2.6.36), when will they get time to test it (so as to freeze it)?
View 7 RepliesI have been working with Linux for some time now and moved from "crash-dummy fedora" to LinuxMint and now I'm on Debian 8.I ... The system is freezing and the only way to get it out of freeze is to kill tty7, I log into tty2 as root(which can startx) and kill tty7 via pid...
At first I thought it might be that I have 10 virtual NICs on 1 physical NIC, but after removing them it still freezes after a few minutes of running. Now I am wondering if double mounting/bind causes issues,
Example: drive2 is mounted to profile2/MyStuff, but I also "mount -o bind" a folder inside profile2/ MyStuff/.opera to profile2/.opera..
This is what I mean by double mounting. Does double mounting cause freezing ?Because I have not double mounted, and it hasn't froze yet. and to be honest, I am double mounting/binding several config folders like .mozilla etc...Drives are SSDs, and I created a complete other drive with LinuxMint and it froze the same way after mounts.
I have a Dlink DWA-142 usb wireless adapter that I am trying to configure on a Debian 6.0 system. I couldn't find any linux drivers for this card so I used ndiswrapper. The drivers (latest xp version from the website) have installed successfully as far as i know because I can see the card and scan for access points using 'iwlist wlan0 scan'.
I tried to use the card with both Wicd and NetworkManager, which both fail to connect to my WPA encrypted wireless router. So after this I went to the command line to find that if I try to connect to the accesspoint using Iwconfig, that the program hangs... as in my terminal does not write a new line because it is waiting for the above command to complete.
I have done:
And the terminal hangs on the above command, so I imagine this is where wicd and network manager were getting stuck too. ndiswrapper is the latest version, compiling from source and reinstalling it made no difference either.
i recently switched from slackware to debian because my laptop kept freezing up on slackware, and now it's doing the same on debian on slackware i would get this error in syslog: "hpet: compare register readback failed" at the exact time of lockup, which would leave me with a blinking capslock led indicator, and a completely frozen system (not even magic sysreq sequence would do anything) now on debian, same symptoms only there's nothing in syslog, and no blinking capslock led hardware is: i7 720q intel pm55 chipset nvidia gt 240m laptop model is lenovo ideapad y550p this will occur both in X and at the console i am using my own kernel as the default kernel doesn't support my ethernet adapter i have tried disabling hpet at boot, but there was no difference i have tried the patch posted here
View 5 Replies View RelatedI am using Squessze and Gnome. When I try to use the gui System>Administration>Network or Users and Groups I get the error The configuration could not be loaded. You are not allowed to access the system configuration.Everything was working before. I read around a bit. In some cases,it was caused by mismatching group and password files after using the gui. I do not know how to check if they are matching. Of course I do not know for sure that is the problem in my case.
View 14 Replies View RelatedI would like to remove a specific domU (test01--pv--guest) from my machine. I am not sure how far/to what extent to remove files. Here are the files and properties it seems I should remove:
lrwxrwxrwx 1 root root 10 Jan 9 11:05 /dev/disk/by-id/dm-name-xenvg-test01--pv--guest--disk -> ../../dm-3
lrwxrwxrwx 1 root root 10 Jan 9 01:03 /dev/disk/by-id/dm-name-xenvg-test01--pv--guest--swap -> ../../dm-2
lrwxrwxrwx 1 root root 7 Jan 9 11:05 /dev/mapper/xenvg-test01--pv--guest--disk -> ../dm-3
lrwxrwxrwx 1 root root 7 Jan 9 01:03 /dev/mapper/xenvg-test01--pv--guest--swap -> ../dm-2
lrwxrwxrwx 1 root root 7 Jan 9 11:05 /dev/xenvg/test01-pv-guest-disk -> ../dm-3
The above link to dm-2 and dm-3.
brw-rw---- 1 root disk 254, 0 Jan 9 01:03 /dev/dm-0
brw-rw---- 1 root disk 254, 1 Jan 9 01:03 /dev/dm-1
brw-rw---- 1 root disk 254, 2 Jan 9 01:03 /dev/dm-2
brw-rw---- 1 root disk 254, 3 Jan 9 11:05 /dev/dm-3
brw-rw---- 1 root disk 254, 4 Jan 9 01:03 /dev/dm-4
brw-rw---- 1 root disk 254, 5 Jan 9 01:03 /dev/dm-5
brw-rw---- 1 root disk 254, 6 Jan 9 01:03 /dev/dm-6
brw-rw---- 1 root disk 254, 7 Jan 9 01:03 /dev/dm-7
Will they be deleted automatically or should/can I remove them? How do I check the need for the other dm-? files? As indicated below, it seems like some may be duplicates.
I also found this set in /etc/lvm/archive/:
-rw------- 1 root root 2909 Oct 17 00:41 Relaise-vg_00000-1453251236.vg
-rw------- 1 root root 2929 Oct 24 22:08 Relaise-vg_00001-1530642081.vg
-rw------- 1 root root 2924 Oct 25 19:33 Relaise-vg_00002-328450675.vg
-rw------- 1 root root 2901 Oct 26 19:53 Relaise-vg_00003-1555350964.vg
-rw------- 1 root root 2902 Oct 26 19:53 Relaise-vg_00004-1044927704.vg
[Code] ....
Some of these seem like duplicates. This may be due to multiple attempts to build the volumes. Is there a way to determine if all of the are useful?
I came across one strange problem. When I try to install a new package on my system, I get this error, connected with libgnutls26:
[Cpde]...
If I shutdown from X the system hangs and I have to yank out the power cord. Same on logout.
ctrl+alt+f1 hangs for a few minutes and then starts a terminal; which does not respond to the keyboard.
There are no tty.conf files in /etc/init .
But inittab looks normal to me and includes tty (1-6)
Executing init 6 from a terminal in X will reboot the system
I was thinking this might be a dbus issue, but I am not sure. I also understand some recent issues exist with SysRq sequences. May be a video card issue,,,
Other than normal package upgrades the only changes were a recent change from a VGA to HDMI cable. I can't see why that would matter
Linux Lugh 3.2.0-4-amd64 #1 SMP Debian 3.2.68-1+deb7u2 x86_64 GNU/Linux
I was wondering if a standard Debian 8 system with Gnome desktop does any kind of local dns caching, and if so, what the command is for clearing it. (Assuming I haven't purposely installed any DNS server software.)
I found multiple posts on the Web about unix DNS caching, but with widely different answers across distributions and across time.
I am running Debian on an ARM module (BananaPi).5 minutes ago, i started upgrading the system, but fortunately the power cable moved and the system closed.Now i open it up again and i'm trying to re-upgrade the system but i'm always getting this message
# apt-get upgrade
E: dpkg was interrupted, you must manually run 'dpkg --configure -a' to correct the problem.
I have installed jessie on a couple of machines. One is configured as the NFS filesystem exporter and NIS server. The other one, I am trying to configure as NFS and NIS client. NFS does not seem too much of a problem, I can mount the exported filesystem to a directory in the client and unmount it, but when I install NIS the system becomes very slow. Any command preceded by "sudo" takes a very long time (a few minutes) to complete. Then, upon rebooting the system, it reports many services failed to start (login, accounts, modem manager, avahi, network manager, exim). When if finally completes, I get a terminal login, instead the graphic login window.
View 4 Replies View RelatedInstalled linux-image-2.6.32-bpo on my laptop today and after the reboot i got "no operating system found" . I'm now typing using a Puppy live cddrom .
View 3 Replies View RelatedI have a small LAN. I am in the process of installing a Debian Lenny/Squeeze system into the LAN. I want to send and receive system messages using rwalld and wall.I can send a system message from my Debian system to another box using rwall. I can send a local message within the Debian box using wall in a console.I cannot send a local message using wall Konsole in KDE 3.5.x. The KDE Write daemon fails to provide any pop-up window./usr/bin/wall is installed from the bsdutils package and is set to -rwxr-sr-x.
The ktalkd package is installed. The KDE control center shows a configuration option in Internet & Network settings called Local Network Chat.When not in X, mesg is set to y at the console. After starting KDE and I open Konsole, mesg is always set to n. I don't know how this setting toggles. Further, setting mesg to y in Konsole has no effect on getting wall to work.mesg is set to y when I run xterm in KDE. Then wall works within that terminal window. However, the KDE Write daemon does not see the message in xterm.When I send a message from another system to the Debian system using rwall, xterm receives the message but not Konsole or the KDE Write daemon.
The purpose of that topic is to identify if there is any way to totally clean a debian system and make it like a fresh installed system (of course i amn't refering to packages because aptitude is just perfect?
View 3 Replies View RelatedI'm running testing and over the last week or two my system is getting slow. Any disk access slows everything to a crawl. Even the cli can take several seconds to display characters as I type them.
View 9 Replies View RelatedI updated squeeze last night for the first time. It worked fine after 1st reboot last night. There was one reboot stalled at "hald" so I shut down and restarted. Worked ok 2nd time around
Today,upon login I got a string of taskbar notification (which I couldnt read as they all overlapped . I was able to see a kernel error message but couldnt report it (network was down) or save it (USB stick not recognised) Some programs worked, others didnt
I have the partedmagic rescue distro on USB stick so have those programs to use in order to fix the problem. Any idea how I can repair this? I tried fdisk for the hell of it. reported clean partition as predicted. I am using debian-testing-amd64-kde.
I have a Dell Latitude E6410 which I can boot from an Iomega external hard drive when I want to run Linux on it. It is a work issued Windows XP laptop and when I travel, I am more comfortable with Linux, so I created a dual boot option without touching their hardware. The external hard drive plugs in to the USB ports and the BIOS picks it up as the primary boot media, although the internal drive is still present. (That is the desired outcome).The problem is that the system periodically locks up solid and only a forced power off will get it to respond. The system seems to go into a kernel panic and fails to write anything before dying. The system completely locks up and stops responding to mouse and keyboard. It also seems to drop off the network. When I look at the logs after restarting, nothing at all shows up related to a kernel panic or anything else. To further complicate the diagnosis, on the reboots, sometimes the boot process locks up at "Starting GDM3", sometimes it doesn't, and wont for several attempts but eventually will boot to gnome. Some times it runs fine for a few hours, sometimes for only a few minutes. Can anyone recommend a way to diagnose this?I am trying to run Debian 6.0 32-bit with the defaults.
View 8 Replies View RelatedI noticed that when my server boots up, it's network interface on eth0 is always down and I always must run the 'ifup eth0' command in order to get it to work for some reason. I checked my configuration and it looks legit to me...
# This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5).
[Code]...
Anyone know why my system is booting with out bringing up my eth0 interface? It's very annoying.
I have just installed Ubuntu (/dev/sda7) and Debian (/dev/sda4), but since I have updated all informations on Ubuntu, then Debian did not appear anymore on the grub list. There is an wiki I have found, but I an not really sure about what to do.
Here are the boot informations:
Boot Info Script 0.55 dated February 15th, 2010
Boot Info Summary:
=> Grub 2 is installed in the MBR of /dev/sda and looks at sector 488861020
of the same hard drive for core.img, core.img is at this location on
/dev/sda and looks on partition #3 for (,gpt3)/grub.
[Code]...
ps: on this file, it says that the /boot is installed on the MBR and /dev/sda3. I will remove the boot from MBR as I am now using /dev/sda3 instead. Sorry for my english
I've just installed Debian 8.2 KDE 64bit, installed wine, and found that a 32-bit Windows program (Agent newsreader) could not see the linux system fonts. (This worked fine on Kubuntu 14.04)
Since this is the first time that I've installed Debian, I'm not sure if I'm missing something obvious or if this is an actual bug.
Steps to reproduce:
Fresh install of Debian 8.2 KDE 64bit.
apt-get install wine
wine wordpad # this is a small word-processor for wine that is supplied with wine
menu -> format -> font
all linux fonts are visible -- so far so good
Because I want to use a 32bit program, I now have to do this, I understand:
dpkg --add-architecture i386
apt-get update
apt-get install wine-bin:i386
But after that,if I run "wine wordpad" and look at the fonts, all the linux system fonts are gone. The only fonts visible are the nine that are built into wine (Courier, Fixedsys, Marlett etc..) So installing the i386 wine support seems to have broken something.
I'm trying to set up my Intel Wireless 3945ABG (which is supported in the kernel) and I don't understand where to start if I want to use systemd to do this.
I've installed my Debian (Stretch Alpha4) base system using the wireless to download the necessary components but when I boot into the system I need to set up the wireless card separately.
I would prefer to be able to install wireless without the requirement of connecting via ethernet so no package installs other than what is downloaded by the installer.
I can't even find documentation on this specific issue because everyone seems to reference /etc/network/interfaces which AFAIK is not supported in systemd. How do I configure a wireless card using only systemd?
DEVICES:
atheros AR9485
realtek rtl8111/8168/8411
atheros-firmware and firmware-realtek are installed from repo.
ifconfig does not show the network devices:
ifconfig -a does show them, i ran the commands ifconfig eth1 up and ifconfig wlan1 up, which resulted in them showing when typing ifconfig, however both still are not working.
(ifconfig)Also eth1 is only showing an inet6 address not an inet/ipv4 address and wlan1 doesn't show any.
Checked the bios and noticed that network devices were enabled so i don't think its my bios.
Also ran a SystemRescueCd which i got from here: [URL] .... With this live cd, the networking was working.
Added:
Code: Select allauto eth1
iface eth1 inet dhcp
allow-hotplug eth1
Now I get a net address...
I want to move my old system to a new drive. Currently I have Debian installed with following configuration:
I have an encrypted system where everything is encrypted except /boot. Currently I've /boot and / installed on a 16 GB mSata SSD and /home on a regulard HDD. I've got a 500GB SSD for Christmas and want to move the whole system to the new SSD.
I just wanted to ask if I've got the process required to to this down:
1. backup root-directory (/) without and /boot /home using tar keeping file-permissions and owners to ext. hard drive
2. backup /boot and /home separately using the same method
2. replace HDD with SSD remove mSATA SDD.
3. boot via live-usb
4. create appropriate volume groups, partitions, setup encryption etc.
5. extract backups to appropriate partitions
6. chroot to old /.
7. edit fstab
8. reinstall grub
9. create new init ram img.
I'm pretty sure I've got steps 1.-6. down but I'm very shaky on what to do next.
I am setting up a mail server on debian. Once it's done, I'd like to have an indentical server on another machine, where debian will also be installed. The solution has to be hardware agnostic, so source machine is different than destination machine. I was reading on some wiki page that one can simply copy the root filesystem via rsync to the computer that he'd like to install the system on, then chroot to it and test if everything works. I'm guessing I'd have to change a couple things before, like :
- The network config
- The /etc/fstab file (disks and partitions may be different)
This article is about using rsync to transfer a copy of your "/" tree, excluding a few select folders. This approach is considered to be better than disk cloning with dd since it allows for a different size, partition table and filesystem to be used, and better than copying with cp -a as well, because it allows greater control over file permissions, attributes, Access Control Lists (ACLs) and extended attributes. [1]
I have a lenny system up and running, my CF-card reader is supported and I can mount a 1GB card. My PC _can_ boot from CF cards, I verified... My Linux resides in sda3 (other partition is XP). How would I transfer the partition to a cf card? I tried using dd if=/dev/sda3 of=/dev/sdb1, but as that doesnt work I have the feeling there's more to do... Maybe install GRUB on the CF-Card? Change some paths after copying?
View 6 Replies View RelatedOkay so a newb question but I typed the simple command sudo apt-get install lottanzb to install lottanzb after adding the testing repositories (currently using Lenny stable) and got a huge shed load of things updated including AWN from the testing source as a result (pages of them flashed by) and it removed some things like Epiphany browser.
Got a load of errors at one point during this including
/var/lib/dpkg/info/libc6.postinst: line 165: [: missing `]'
Usage: /etc/init.d/cron {start|stop|restart|reload|force-reload}.
/var/lib/dpkg/info/libc6.postinst: line 165: [: missing `]'
Status of Common Unix Printing System: cupsd is running.
/var/lib/dpkg/info/libc6.postinst: line 165: [: missing `]'
checking separate queue runner daemon...done (not running).
[Code]...
Am I being dumb here or does that mean I`m now basically using Debian testing as a result and if so how can I undo it yet keep LottaNZB? With the errors am concerned in case I reboot and the system goes from stable to unstable. I chose Debian for the stability so don`t want the testing versions, and have no idea why a simple install command updated so much stuff. EDIT: It bigtime messed it up, when I logged out and logged back in system was unusable and I had to reinstall as tried apt remove but it didn`t undo it. Quite surprised that Linux breaks easier than Windows though
Debian 2.6.32 Squeeze + GnomeI try to start System | Administration | Services and I get an error:The configuration could not be loadedAn unknown error occurredI turned on a whole bunch of different services and suddenly now I can't get back in to switch any of these on or off. I'm assuming there is some manual way of switching these off again, I just don't know where to do this.
View 3 Replies View RelatedRunning AQemu says me the following:
Could Not Get USB Information From System!
USB Support is Disabled.
Add Support proc FS TO YOUR Kernel.
This laptop that I am trying to get Debian 5 working on is occasionally locking up during boot at "Activating Swap..." WTF could cause such a bizarre thing? The swap partition is just empty space. Activating must be nothing more than confirming it exists and mounting it.
View 3 Replies View RelatedI have never seen this one before (see below) - note how /dev/sda1 is mounted from the first disk listed by fdisk, but /dev/sda2 comes from the second disk; what is going on here? This is what I did: I installed the latest debian "Testing", which went well - it found the disks in the order show by fdisk -l here. When it booted up after installation, it failed because it couldn't find /, which I repaired by editing the grub menu (I told it to start from the other disk), and it came up. But now I had to mount /u01 by hand from /dev/sda1; strange. I suppose I could just go and change the physical disks around, but I'd like to understand this. Any ideas?
# fdisk -l
Disk /dev/sda: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000
[Code]...