I have my X11 setup configured to rotate 90s counterclockwise for a portrait monitor. But when the system turns on, it's in the framebuffer console which is set to landscape mode. Is there a way to set it so that even the console is rotated in portrait mode? I'd like to do this automatically.
View 6 RepliesI'm trying to change my screen orientation from landscape to portrait mode. Here's my system information. (I don't have an auto-generated xorg.conf file.)
$ uname -a
Linux jzd 3.14-0.bpo.2-686-pae #1 SMP Debian 3.14.15-2~bpo70+1 (2014-08-21) i686 GNU/Linux
$ lspci
...
00:02.0 VGA compatible controller: Intel Corporation Haswell Integrated Graphics Controller (rev 06)
...
[Code] ....
Here's the error message I get when I try to use randr:
$ xrandr --orientation right
X Error of failed request: BadMatch (invalid parameter attributes)
Major opcode of failed request: 149 (RANDR)
Minor opcode of failed request: 2 (RRSetScreenConfig)
Serial number of failed request: 14
Current serial number in output stream: 14
I'm always getting a blank console screen after booting a 2.6.32-trunk-amd64 kernel in squeeze. I still can read the line "Loading, please wait ..." in the display for a second - then it's completely black until X windows is starting. When I try switching from the X console to another virtual console (by pressing Ctrl-Alt-F1 e. g.), the complete system freezes. I have to hard reboot then.When I boot the previous 2.6.32-3-amd64 kernel instead, everything is fine as expected, though.There's a line "GRUB_GFXMODE=1024x768x16@60" in /etc/default/grub as well as a line "set gfxpayload=keep" in /etc/grub.d/00_header. So the problem might be framebuffer related in any way. Any ideas what could be tried?The system is a Latitude E6500 with a Mobile 4 Series Chipset Integrated Graphics Controller
View 2 Replies View RelatedThis only started after the recent updates which included a lot of sysv stuff in Squeeze. I'm not talking the Gnome or Xwindows consoles, I'm talking the full-on type you get when you do the CTL-ALT-F2 type of console. before those updates, I had no trouble. Now I can't get back into the gui by pressing CTL-ALT-F7 as usual. All i get is just a black screen. I do have the nvidia proprietary driver installed using DKMS, and I am running the latest (I think) liquorix kernel.
View 5 Replies View RelatedMy Squeeze installation has the horrific 80x25 line display, and I cannot stand it. I know it can do better, because the grub screen is very tiny. I ran dpkg-reconfigure console-setup, but the offerings there aren't much better. I don't know what happened to the good ol' days of grub when all you had to do was pass vga=791 to the kernel to get a decent console size... but it seems they are gone.
I don't really understand this new v2 grub... I don't know why it was necessary to change how it was configured, when it seemed to work so exquisitely. how I would accomplish the functional equivalent of passing vga=791 (1024x768@75hz) to the kernel in grub
I used the Monitor setup to indicate that my widescreen monitor is rotated 90 degrees to the left, to make it long for editing code, but the login page still does not rotate. I am assuming this is something simple, and probably a user defined option since my user is likely the only one with the monitor rotated, as there is just my user defined, but there are the other system ones, including MySQL. I am running Ubuntu 10.10 upgrade from 10.04.
View 3 Replies View RelatedI've just tried to install X on my new debian system which had a nasty side effect.
I can see the bootcycle up to "Waiting for /dev to be fully populated." and then the screen switches into a display mode unsupported by my display. I've had problems like this many times before because the display returns it's capabable of resolutions like 2048x1536, which it just isnt. I've had to disable autodetection whenever using this display. One thing to note thought is that it's NOT X that's messing up the display. It's setting the wrong display mode even before the filesystems are mounted. And I've already uninstalled X with no change either. Also recovery(single user) mode has no proper display output either.
what is setting my display to the wrong mode?
My problem is that I anyway cannot get to the text console when I have run the desktop environment. When I press Ctrl+Alt+Fx (where x - number of tty console), the video adapter doesn't send signal into monitor. Keyboard also stops reacting, only Magic SysRq Key works. The same result I can see when I turn off the desktop environment (I have uninstalled gdm) or kill X-server with the "kill -9" command. The only way to get to console (except window terminal) is remote connection via SSH.
The problem occurs only when I have run X-server. When I turn on the computer, I can see start messages. Since I've uninstalled gdm, I have also access to the console after I turn on my computer. I can normally switch between tty consoles, until I type "startx" command. Everything started when I've tryed to install non-free ATI video drivers. They practically worked, because I've had some problems with them (I just don't remember what problems), so I've uninstalled them and returned to the open. Then this problem apeeared. I tried to reinstall Xorg, change kernel (installed from repos), switch off the framebuffer, but it gave nothing.
[Code].....
I'm getting a weird charset problem in a chroot'ed system that I kexec'ed into. It is especially noticeable in ncurses programs like aptitude, but it also noticeable in vim. [URL] My locales are configured to en_US.UTF-8, I have choosen my keyboard layout with kbd-config while in the chroot before kexec'ing into it, I've passed the bootkbd= parameter to the kexec'ed kernel, and my TERM variable is set to "linux". I can't try xterm because this chroot system doesn't has X.
EDIT: I just noticed that the keyboard layout I selected is not working properly. All keys work fine except the ones that are specific to my country. Instead of รง I get a weird symbol.
I was installing some packages yesterday, I think one of them was an update for grub. (I'm using grub 2). When I rebooted, the console text was in green, not the usual white. (using gfxpayload=800x600 i.e. console is in graphics mode). I first thought maybe it was some kind of St. Patrick's day joke, but now I am getting tired of it. How do I set the color scheme back to normal?
View 7 Replies View RelatedI've configured my debian lenny to load first the command line, then if i want I load the X server, but doing this to that way I don't have the suspend/hibernate functions from the gnome menu, so, my question is:
what is the command to suspend / hibernate my system at any moment I decide?
I've looked today on my logs /var/log/message and I find device eth0 entered promiscuous mode I don't remember putting eth0 in promiscuous mode I'm connected to the net thru a router how do i turn that off ?
View 1 Replies View RelatedI know that in an xterminal I can redefine the default colour with something like
!!red
URxvt.color1: rgb:cc/00/00
URxvt.color9: rgb:ef/29/29
Is it possible to do something similar in the Linux (framebuffer) console?
The resolution is OK in grub menu but after something is setting to higher value. How can i set it back to 640x480?
View 1 Replies View RelatedI would like to put an image in the background of my console (tty) like done by Gentoo or Suse : I found several tracks to follow, but I would like to have your advice on the best way to do that for Debian.
View 3 Replies View RelatedI'm trying Debian again just for fun after using Slackware for years. When I "su -" on Konsole in Debian I get this for my prompt:
Code:
darksaurian@darkswamp:~$ su -
Password:
darkswamp:~#
darkswamp is my hostname that I made up when I installed. On Slackware I'm used to it saying:
root@darkswamp
or something like that.
I'm starting Konsole the same way on both:
konsole -e $SHELL -l
I kind of wish it still said "root" just because I'm used to it.
I know there are many threads regarding this topic.I probably read most of them. At installation time I told Debian to use German keyboard layout (since I am from Germany). Now I want to switch it to American keyboard layout. In X this was no problem. But in the tty consoles I cant get it changed. It does not matter to me if it is system wide or user wide because I am the only user. (system wide would be a little bit more preferrable because it would affect the super user too, I think).I tried dpkg-reconfigure console-data
and selecting my desired layout. This changes the Layout to American until reboot
I've been scouring the internet for an answer to this problem. I am using Squeeze and have properly configured Grub2 to set my console screen resolution to 1024x768x32 (as per updating /etc/default/grub to contain 'GRUB_GFXMODE=1024x768x32' and updating /etc/grub.d/00_header to contain 'set gfxpayload=keep') and everything works wonderfully. My resolution is set as it should be. However upon installing Xorg (aptitude install xorg ratpoison), my console resolution gets changed to what appears to be 1280x1024.
I thought that this was due to xrandr, however when I issue:
# xrandr -s 1024x768
only the X resolution is changed. When I then CTRL-ALT-F1 back to the console, the resolution is still at 1280x1024 (I am aware that xrandr only affects X, but I assumed that because my console resolution was correct before installing X there might have been some correlation).
I would like for my console resolution to stay at 1024x768 as per Grub2's configuration and for X's resolution to be at 1280x1024.
PS I also noticed that prior to installing Xorg, my CPU boots up without any screen blanking (only for a second or so). However, after installing Xorg, during the boot process the screen does blank briefly. It is at that time that the resolution gets changed to the 1280x1024 setting.
I installed the base of Debian (only CD 1) without the desktop environment, so it is console only; also I am dual booting with Windows 7 x64 on this Dell Inspiron 1545 laptop... I have also successfully mounted my usb flash drive and CD drive; the one thing I am finding rather hectic is finding a way to connect to my wireless network with a "WPA2 Personal" Security and "TKIP/AES" Encryption with a Dell Wireless 1397 WLAN Mini-Card... I doubt that the drivers are actually installed, and Idk how to install them.Google searches on this yield confusing results, so I need help. So far, the most useful help I have found is the link posted here: http://en.community.dell.com/support-fo ... 29916.aspx but I have no idea on how to install that, if it is even what I need.
View 5 Replies View RelatedReinstalled Debian Squeeze (64bit/gnome) on my Notebook using Netinstall. Everything worked like always but in the setup instead of typing in a root password as asked to i just pressed enter (in the hope of not having to type in a pw in the console later, just having to press enter then)
When i needed rootpw to install some software (using SoftwareDownloader) the normal loginpw seemed to work, but not in the console.
ari@HP625:~$ su -
Password:
su: Authentication failure
[Code]....
I just installed Debian 6 and need to change the console keyboard layout (I am not running any sort of gui).I installed 'console-data' and ran:# dpkg-reconfigure console-dataThis assigns my Apple keyboard keys perfectly but it won't survive a reboot, which is really important for entering passwords
View 2 Replies View RelatedSince moving my debian server over to a Gigabyte H97N-WIFI motherboard the console dims on booting and generally stays dark. Strangely the screen the brightens up if I go to an emergency shell, but if the boot runs successfully I don't see the resulting login prompts. Also, during the boot process the messages to the console are too dark to see.
I've tried the i915.invert_brightness=1 fix mentioned here [URL].... but that seems to have no effect. I'm assuming that this has something to do with moving to intel graphics as my previous hardware had a radeon graphics card and didn't display this problem.
After install debian 8, I can't see system start and stop message from console ... How can I enable system message from console in debain 8?
debian 7 output
----------------------------------------------
root@demo:~# service apache2 restart
[ ok ] Restarting web server: apache2 ... waiting .
root@demo:~#
debian 8 output
-----------------------------------------------
root@demo:~# service apache2 restart
root@demo:~# <=============================== No message (start or stop)
After an update on squeeze about a week or two ago, my console font turned green. I'm not exactly sure of the timing, because I switch between lenny and squeeze, and some time passed between the update and the reboot in squeeze.
During the update, I was asked if I wanted to keep my altered /etc/grub.d/00_header or take the package maintainer's version. I took the PM's version, knowing I'd lose my edit (set gfxpayload=1024x768x16). When I add that line to the new 00_header, run update-grub and reboot, the console font is the size I want, but it's a dull green. Reminds me of my first computer. How do I get it back to white and keep the 1024x768 resolution?
Currently booting with grub-legacy and chainloading grub2. If I boot entirely with grub-legacy, and pass vga=791, the console font will be white. It doesn't matter which kernel I use. Currently, I'm running 2.6.32-3-686. Same behavior exists if I use 2.6.30-2-686. If I use 1024x768x8 I get a dull gray instead of dull green.
I have been using my system for couple of weeks, and normally update software when the icon is displayed on top bar (gnome). Last couple of days there were updates for X, and I am not sure whether that is the cause of my problem. Once bootup, I get the login screen. When enter the password the login screen keep coming back. there is no error about any password issue, or anything. It keeps prompt me to enter the password.
I could login back the following way.
1. ctrl + alt + F1 , and login with the same username/pwd as for X
2.change to root
3.pkill gdm3
4.exit from root to user privilege
5. startx
The system starts X correctly and no login screen is displayed. I could use the system as usual.
The only thing I did custom to my system was upgrading to the latest kernel (2.6.38) using the source. This was to get support for my hardware, but that was about a month ago. I do not see anything in /var/log (X, demesg etc).
I installed 2.6.38 from backports. It boots OK, and among the start-up messages it says it has started kdm, but then it offers only a console login prompt, no GUI. I assumed (perhaps optimistically?) that newer kernels would be backward-compatible, and that any dependencies on other software would be enforced by the package mechanisms. Running amd64, Squeeze, KDE.
View 6 Replies View RelatedI've recently installed a new graphic card after my old one started to go belly-up and it works nicely in X with twinview. The card have one VGA, one DVI and one HDMI. I have the monitor connected to the VGA and my projector connected to the DVI. However, when I boot the monitor (VGA) don't receive a signal. It is dead until X comes up (and when X comes up it does exactly what I want, it uses the VGA monitor as the main screen).
I had this setup on my old card to and it worked fine. Grub and boot console showed on both screens and I never had to tweak anything to make it do this.
how to enable the VGA outlet, either have boot enabled or only the VGA enabled (either way is fine by me but I really want to see Grub and the boot console on startup).
So this also happened to me when trying to install an old version of Ubuntu (hardy I believe). I have a Sun Netra X1 that I am trying to install the latest stable Debian Sparc64 port on. I'm doing a TFTP boot, and am able to get the kernel to load. However, once the kernel loads the installer, the screen gets garbled (attached is a screenshot from my console session) This server has no graphics card, so I have to install using the serial console. I don't recall having this issue when I installed the last stable version. Any ideas what's going on or how to fix it? I even passed the option "DEBIAN_FRONTEND=text" to the kernel, but it didn't seem to do anything.
View 2 Replies View RelatedAfter upgrading my Debian from Lenny to Squeeze a few things don't work properly. Most disturbing is that after one switch from graphic screen (x, Gnome) to the virtual consoles this can be observed:
1) The virtual consoles show only a small font. It doesn't change when I use 'dpkg-reconfigure console-setup'. Otherwise everything seems to function properly, but then
2) I return to x (with Alt+F7), and if I again want to reach the virtual consoles (with Alt+String+F3, this is a laptop) the screens are persistently black; nothing works, except Alt+F7, which allows me to go back to the x-screen. In this graphic screen it is possible to use the consoles without problem.
3) I have some trouble shutting-down the computer. The screen disappears, everything goes black, but the computer goes on and does not shut down until I press the power-button, forcing the shut-down process. If I press the keys which would bring the computer to a halt through the virtual consoles, I can bring it to stop allthough the screen remains black throughout the whole process. I press: Alt+Strg+F3 to reach the consoles, there 'root + password', Enter, halt, Enter. Nothing at all appears on the screen, but after a while the computer stops.
I cloned my disk that have dual boot in it clone the disk remove the old one put the new one so far okay. But when i put with the new disk to linux it goes to the emergency mode:
run fstab and this is my fstab results:
# <file system> <mount point> <type> <options> <dump> <pass>
# / was on /dev/sda1 during installation
UUID=cd9637db-0479-4ef0-90fd-481a50e23060 / ext4 errors=remount-ro 0 1
# swap was on /dev/sda5 during installation
UUID=df29ffb9-91a8-48d7-91cd-5e671b55677d none swap sw 0 0
/dev/sr0 /media/cdrom0 udf,iso9660 user,noauto 0 0
UUID=696FF92C4C532245 /media/Windows ntfs defaults,x-gvfs-name=Windows,x-gvfs-icon=%2Fhome%2Fdarkangel%2FDownloads%2Fwindows_hdd_icon.png,x-gvfs-show 0 0