Debian Configuration :: How To Run Pure Sid

Jun 23, 2011

I am a long time aptosid user which asked to many question in there forum. Everyone interested: [URL] Anyway eat shit and die is not quite the answer I was looking for. I want to stay with a Debian and a rolling release, so I was wondering if some of you could share some info's on howto best setup and run pure sid.

View 9 Replies


ADVERTISEMENT

Ubuntu Installation :: Remove Pure-ftpd Pure Admin - Getting A 530 Authentication Error

Mar 24, 2011

I am having problems troubleshooting my pure-ftpd setup. I am always getting a 530 authentication error. I attempted to correct the problem by doing the following:

# pure-pw mkdb
# ln -s /etc/pure-ftpd/conf/PureDB /etc/pure-ftpd/auth/PureDB
# gedit /etc/pure-ftpd/conf/PAMAuthentication

[code]....

This create a new error. 421 Unable to read the indexed puredb file (or old format detected) - Try pure-pw mkdb I am getting a feeling this is getting from bad to worse. I attempted to remove pure-ftpd and pureadmin to start over again. However, it appears I cannot remove everything. I attempted the following:

apt-get remove pure-ftpd pureadmin I am not sure what this really does because I can still see the folder /etc/pure-ftpd and I cannot remove it. I could not use rm /etc/pure-ftpd because the system said it was not empty. I also tried sudo aptitude remove pure-ftpd pureadmin . Again I cannot completely remove the folder. How do I completely remove pure-ftpd and pure admin and all databases, files and folders so I have a fresh system ready to start the install again?

View 1 Replies View Related

Software :: Pure-authd Not Passing Variables To Pure-ftpd

Feb 9, 2011

I have set up pure-authd and pure-ftpd. They are both running, I have created the socket etc.

In my authentication module (a php script) for testing purposes I have done a vardump in to a file, and have realised that pure-authd is not passing on any variables (username, password of the current person trying to log in via ftp) to the PHP script.

I am sure the authentication module is working (have tested it vigorously on the command line), but after 10 hours wondering why it wouldnt work and messing about with the script, I have realised that the variables were never even getting in to the script in the first place!

I am running the processes such as this:

Everything seems as if it is working other than this. For instance, when testing the setup with a very basic auth module which doesnt require a username or password (the basic module just passes "auth_ok:1" to pure-ftpd and the user is then logged in), I can log in to the FTP server fine.

But like I say, a vardump ($argv) on my proper PHP authentication script would suggest that no username or password are being passed to it.

View 1 Replies View Related

Debian :: Transform LMDE Into Pure Squeeze?

Nov 13, 2010

I am having some good time with Linux Mint Debian Edition, but I want to transform it into Debian Squeeze. In my installation, I've just 7 minty packages, the rest are from debian repo. have a detailed look here [URL] and suggest me debian replacements of those 7 minty packages.

View 6 Replies View Related

Fedora Servers :: Pure-ftp Welcome Message

Nov 13, 2009

I am having problems with the welcome message regarding pure-ftp, this is on Fedora 10. Pure FTP just doesnt show any ability to change the default message, its rubbish at its default gives out some details of what I am running (security risk in itself). Is there any means of being able to make a custom message?

View 4 Replies View Related

Fedora X86/64bit :: Possible To Keep X64 Instalation PURE 64 Bit

Jan 25, 2010

I'm very new to Fedora ( i want to install it again on my PC ) but i have a small question before i proceed.Is it possible to keep a x64 instalation PURE 64 bit ?I mean here, will fedore try to install a 32 bit library ?? or ONLY if i need them ?Because for example openSuSe will install 32 bit libraries right from the start

View 5 Replies View Related

Ubuntu :: Getting Back To Pure Gnome

Nov 18, 2010

EDIT: The way the ubuntu forums formatted it made it easier to understand, and I installed the misisng packages. So I installed kubuntu plasma desktop, so that I could try KDE, and decided I didn't like it. So I followed the psycho cat tutorial here on [URL] "Getting back to pure gnome on Ubuntu" I copy and paste the code there, and it starts uninstalling, but then I get this:

Code: Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following packages have unmet dependencies:

libaccess-bridge-java : Depends: default-jre but it is not going to be installed or openjdk-6-jre but it is not going to be installed or sun-java6-jre but it is not going to be installed E: Broken packages I have absolutely no idea what to do. I know it has something to do with missing dependencies (anyone could, if they read the code) but I don't know what to do.

View 2 Replies View Related

Debian Configuration :: ProFTPd Configuration - Use To Host MySQL Databases And A Few Websites

Nov 18, 2010

I am having no luck configuring ProFTPd on a Debian Lenny production server we use to host our MySQL databases and a few websites. I had originally set it up so I could login and manage our internal sites, but I have the need to allow a few clients in to access their sites that we host. I am trying to root the users in their site directory, which would be "/sites/www.whatever.com/".

It just hit me while typing this. Is it possible to create a user without a shell to prevent login via SSH and set the home folder to /sites/whatever instead of /home/username? That would allow me to continue operating with my current configuration and root them in their site while preventing SSH logins.

View 6 Replies View Related

Debian Configuration :: Multipath Configuration On 5.0 64 Bit - Doesn't Create The Relative Devices

Jul 20, 2011

i have a HP MSA 2312fc SAN with 2 LUNs configured. The first LUN (LUN ID 1) is correctly connected to the system, but when i connect the second LUN (LUN ID 30), i find in the syslog this message: multipathd: 8:64: size 6835937472, expected 5267578112. Discard

Here is the multipath.conf

[Code]....

So I correctly see the two luns, but multipath doesn't create the relative devices. Under /dev/mapper I see: control mpath0 mpath0-part1 mpath0-part1 is the first lun, the one I mounted in a directory under filesystem. I can't find the device for the second lun

View 1 Replies View Related

Debian Configuration :: Reboot Both The Server And The Client Machines Every Time Change The SAMBA Configuration?

Apr 5, 2010

I am *finally* getting around to rebuilding my file-sharing computer. I'll be sharing files with both Linux and Windoze machines. It's a home network, so there's nothing fancy needed. I know I have to tweak my smb.conf file until I'm satisfied with the features and security. I'm using SWAT and I'm starting with a bare-bones conf file. It's not secure but I can see the server and selected files/directories from my other Linux box.

My really dumb question is, do I have to reboot both the server and the client machines every time I change the SAMBA configuration? I thought I just had to stop and restart the SAMBA service in the SWAT software - but then the server disappears from my client. It looks like I need to reboot both machines for the client to see the server.

View 1 Replies View Related

Debian Configuration :: Fstab Configuration - Failed To Open /proc/filesystems: No Such File Or Directory

Aug 23, 2011

I have some errors when run the mount -all command: mount: wrong fs type, bad option, bad superblock on /dev/sdc5, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail  or so Failed to open /proc/filesystems: No such file or directory

[Code]..

View 14 Replies View Related

Debian Configuration :: Fstab Configuration And Timeout - Automatically Continues Booting Even If The Hard Drives Are Not Attached?

Aug 3, 2011

I have a PC104 running debian. I have 3 hard drives (in addition to the one booting) mounted in fstab by UUID. I use the options defaults,error=remount-ro. However, this means that when I boot with the hard drives not attached, I have to press Ctrl-D to bypass when the boot discovers the drives are missing. Is there a timeout commandoption I can add to fstab so that it automatically continues booting even if the hard drives are not attached? I could not find anything on a timeout command. (I tried adding timeout=1000 but no-random guess)

View 5 Replies View Related

Debian Configuration :: Boot Via PXE, "no Default Or Ui Configuration Directive?

Mar 19, 2011

A week ago I opened this thread viewtopic.php?f=17&t=61580 in "Board index ‹ Help ‹ Installation" and asked for a moderator to move this to here. Because it hasnt happened up to know, I am reopening the thread here. It would be reeeeally great if somebody could help me with my problem!

I own two computers, one netbook and one laptop. I want to boot my netbook as a diskless client via PXE.I set up a dhcp-, tftp and nfs-server on my laptop but when i boot my netbook, the follwoing messages are displayed:(to make it more clear, i uploaded the whole output and shortened the output below)

[Code]...

View 1 Replies View Related

Debian Configuration :: No Longer Allowed To Access The System Configuration

Jul 31, 2011

I am using Squessze and Gnome. When I try to use the gui System>Administration>Network or Users and Groups I get the error The configuration could not be loaded. You are not allowed to access the system configuration.Everything was working before. I read around a bit. In some cases,it was caused by mismatching group and password files after using the gui. I do not know how to check if they are matching. Of course I do not know for sure that is the problem in my case.

View 14 Replies View Related

Fedora :: Authentication Failure On Pure-ftp Server ?

Apr 16, 2011

OS=FC14 x86_64
DM=Gnome

I've installed pure-ftp, and the firewall is open on port 21, the router has port forwarding.

I can connect to this machine, from my smart-phone and a laptop using its IP Address 77.xx.xx.xxx

I'm getting user OK but its not accepting my password or one I just made on another account

This is whats happening:-

What layer of extra security is stopping this working, as the guy attempting access is trying to send a file to big to attach to an e-mail.

View 1 Replies View Related

Ubuntu Servers :: Pure-ftpd DontResolve Being Ignored?

Apr 12, 2011

I'm really confused with this one. Yesterday our FTP cluster went down, i havent yet tracked the reason but i suspect a security update killed it as automatic updates are enabled (i will be turning those off now!).

Anyway, FTP connections were receiving a 425 Sorry, Unable to resovle error message, i sound the solution to be to disable dns lookups with the DontResolve > yes option.

but for some unknown reason this is only working on my failover box! when i restart pure-ftpd on the primary box the command switch -H is missing?

i've done the same thing on both boxes by creating a file in /etc/pure-ftpd/conf called DontResolve and editing it to just read the word 'yes', been over it and checked for spelling mistakes and i cant find any reason why its ignoring the option?

View 2 Replies View Related

General :: Start Up A Net Connection With Pure Terminal?

Mar 26, 2010

I type in ifconfig eth0 up, it says Device not found.

Sys: Fedora12, ethnet, laptop.

When I can get in X, I can manage my network with network-management, or with gnome-terminal. In X, I can start a net with "ifconfig eth0 up", when I type in "ip link", It shows like

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 00:26:22:de:c0:94 brd ff:ff:ff:ff:ff:ff
3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN qlen 1000
link/ether 00:26:c6:4f:79:2a brd ff:ff:ff:ff:ff:ff

BUT right now, I get problems with X and can't get in it. I want to start a net connection in pure terminal and work with it. However, it replys "Device not found" to "ifconfig eth0 up". Answer to "ip link" was lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 and no more. Where is my eth0 then? How can I start a net with it?

View 4 Replies View Related

Server :: Pure-FTPD - With-uploadscript On Fedora 10

Dec 16, 2009

I am running an FTP server using Pure-FTPD which was a migration from an OS-X workstation to Fedora 10 - VMware esxi.

This was done for various reasons but the reason for choosing the Pure-FTPD app was due to an easier migration.

The system has been migrated for about a month and works very well. I installed it on the server using yum install pure-ftpd, configured it and imported all the accounts [about 150 accounts] so this is all fab. however we now want to see if we can get an upload notification.

This has lead me to look at the uploadscript option in pure-ftpd. we use virtual users and the pure-pw file.

The Problem:

When we set the directive

Code:

The ftp server hangs, I cant seem to see how to get this to work, from my investigation I think the issue is that the yum install is not building the app " --with-uploadscript " i have tried to do a hand install on a test Fedora 10 VM, I downloaded pure-ftpd-1.0.27.tar.gz and unpacked it, did a ./configure --with uploadscript then a make and make install, nothing reports any errors but it doesnt seem to install anything. I can start the server from a command line but there are no config directories ? and even after creating a new user and a passwd-mkdb i cant log in to the server. but that most likely as i dont have a full configuration. but i can t find where to put the configuration files.

View 1 Replies View Related

Software :: Pure Data Installation On Fedora 11 ?

Aug 31, 2009

I've just tried to install PD on fedora 11 by downloading it and following this list:

Quote:

When I start PD by typing "pd" in the terminal I get the following error:

Quote:

View 2 Replies View Related

Programming :: Cannot Edit B800:0000 In Pure Dos

Nov 11, 2010

I write the below sample program named "h1.asm"?

Code:

assume cs:code
code segment
mov ax,0B800H

[code]...

1. In Windows platform +MASM 5.0, run "command" and use "debug.exe" to see what would happen. As step by step check, I see B800:000 is not modified as expected.

2. In Ubuntu 10.04 + dosemu 1.4.0.1, run the program in two ways:

a. If exec dosemu in command line as "$dosemu -dumb", yes, it's in shell mode. and then use debug to check, "B800:0000" can be modified as expected.

Code:

"Welcome to dosemu 1.4.0.1!"
D:masm>debug h1.exe
-r
AX=0000 BX=0000 CX=000F DX=0000 SP=0000 BP=0000 SI=0000 DI=0000

[code]....

b. If exec dosemu in command line as "$dosemu", and run the program again, the symptom is as same as 1.(pls see attachment picture).

3. In Windows, I replace "mov ax,0B800H" to "mov ax,2000H" and try again, it would be edited well. So I wonder if it is coursed by "B800" segment address.

View 5 Replies View Related

Programming :: Write A Module In Pure Assembler?

Jan 16, 2010

I need to write a module in pure assembler.Now the linker needs symbols out of the kernel library to link to ( module_init, module_exit, printk).Does anybody know the kernel library name, or are these symbols only in the compressed kernel image (vmlinuz) ?And if, how can I link to a compressed kernel image ?

View 6 Replies View Related

Slackware :: ClutchOS V12.2 A Pure 12.2 Live CD / USB With Persistence

Feb 27, 2010

why another slackish distro? Mine (will be) better than most Please try it before you criticize it It is quite unique in many ways I really did it to show how easily one can make their own 12.2 install into a live distro So, it is a proof-of-concept thing Desktop: My own JWM creation heavily based off Vector's JWM Display manager: Slim from Slackbuilds Packages: All pkg's are 12.2 slack, sbopkg's, and slapt-get/gslapt from Slacky, some others converted from absolute/salixos/source. I custom built the JWM desktop, systray-volume-control, and many from-scratch scripts.

Heres some of the pkg's Games: Xgalaga sbopkg Graphics: Gimp, Imagemagick Office: Abiword, Gaiksaurus, Xcalc Multimedia: Mplayer, XMMS, Audacious, Alsamixergui, Pulsaudio Alsaplayer, Isomaster Misc: Roxterm,rox-filer, PCMANFM, lxterminal, lxtask, leafpad xarchiver, catfish, lxappearance, nitrogen System: Gparted, ddrescue, testdisk, Gnome net tools, WICD wifi-radar, Gslapt, Network: Firefox, dillo, xchat, gftp, grsync

[Code]...

View 13 Replies View Related

Debian Configuration :: Coding The Apache2 Charset Configuration?

Mar 5, 2010

I use apache2 with virtual host and I 've a solution of Webftp who run on it. This solution send automatically email when a new client register himself. In the header of the mail I look this "Content-type: text/html". But when I look this mail with Outlook 2007 the accents are bad coding.It's a script who generate this Html content email.

View 1 Replies View Related

Debian Configuration :: Exim4 Configuration For Local Addresses

Jun 17, 2010

I am working on a Debian 2.6.26-19 Distribution with exim4 as MTA. After a system restart a problem occurred with delivering emails to local addresses. These local addresses use a 1and1 mailserver for email. The MX records for the local domain are set correctly but exim does not use a DNS lookup for these addresses because it identifies them as local addresses. I figured this out by executing the exim4 -d -bt command. The dns lookup part of the result looks like this (I replaced the actual address with placeholders):

[Code]....

The eventual result of the exim4 -d -bt command is: [user]@[domain.ext] is undeliverable: Unrouteable address How can I make sure, that exim4 makes a DNS lookup for the local addresses instead of skipping it? I know that I have to edit a exim4 configuration file, but I could not figure out which and how.

View 1 Replies View Related

Debian Configuration :: Squeeze D-u - Kernel Configuration Skipped

Jul 6, 2010

I have a set of vm's with stable, testing, and sid to keep track of how things are going. When I did an apt-get dist-upgrade with squeeze last week, things seemed to OK (350 package updates) until the end. It didn't seem to like and / or was confused by a kernel dependency.

I am not too concerned yet. Because these are in vm's, I do a snapshot before any significant change. I can futz around with impunity because I have that backup.

I re-booted, and tried the apt-get dist-upgrade again with same results. I think I also tried apt-get -f install.

So I reverted to the snapshot, and will simply try again in the future. I recall that with lenny as testing, the font-desktop was really screwed up for about a period of 6 weeks.

However, just in case someone else runs into this:

1) a re-boot worked, but the failure of apt-get made me nervous enough to revert.

2) waiting for corrections has seemed to work in the past (with a single exception with a 4-disk SCSI software RAID10 update that failed to re-boot lenny successfully after what seemed to be a minor update -- that was on a real system, not a vm. I haven't gotten back to look at that.)

View 14 Replies View Related

Debian Configuration :: Get The Windows One Working Again - Grub Configuration

Oct 3, 2010

I was trying to get the Windows one working again. Here's what fdisk -l reads:

[Code]...

I'll change these or do some grub configurations, if anyone knows what ones can work.

View 1 Replies View Related

Debian Configuration :: Saving Configuration And Packagelist For Reuse?

Nov 14, 2010

I have problems with the system harddrive. I would like to install my Debian on to a new HDD with the same configuration and packages. How do I get the configuration to the new Debian. What files/directory do I need to copy? How do install the same packages?

View 4 Replies View Related

Debian Configuration :: Kannel Configuration For Huwei GSM Modem

Jan 24, 2011

To configure SMS gateway using Kannel configuration for Huwei GSM Modem

dmesg gives attached modem in my system:

View 2 Replies View Related

Debian Configuration :: Bind - Zone Configuration Error?

Apr 30, 2011

I have a problem with the configuration of the NS zone. Looked through the logs, and there:

Apr 28 21:20:19 szewczyk named[18340]: /etc/bind/db.domain.pl:1: no current owner name
Apr 28 21:20:19 szewczyk named[18340]: zone domain.pl/IN: loading from master file /etc/bind/db.domena.pl failed: no owner

[code]....

View 1 Replies View Related

OpenSUSE Install :: Upgrade BIOS For A Pure Machine?

Dec 9, 2010

I'm attempting to upgrade the BIOS in an ASUS 1005HA netbook. The netbook runs SuSE 11.3, and no other OS. All the BIOS utilities on from ASUS are Windows or DOS based. ASUS has a utility titled afudos that apparently flashes the programmable ROM. Running afudos using the dosemu utility suggests that one needs to create a DOS boot drive, execute afudos during a reboot with the new ROM image located on the drive.

How does one accomplish said task on a netbook without a floppy disc drive? Do I create a bootable DOS USB flash drive that contains just afudos and the new bios flash rom upgrade? And if so, how does one do this? As a side issue, it looks like all the major motherboard vendors do not support Linux. That is, all the motherboard drivers require Windows or DOS.

View 7 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved