I did this several other similar servers here today without errors. I'm not quite sure what I'm getting hung up on here.
[root@devoratech yum.repos.d]# rpm -q centos-release
centos-release-5-3.el5.centos.1
[root@devoratech yum.repos.d]# yum repolist
[code]....
I was trying to update my Fedora 15 amd64 when a Error Notification popped up saying "An unspecified TRANSACTION ERROR has occured". More details: "could not add package update for fedora-release-rawhide-15-3(noarch)updates: fedora-release-rawhide-15-3.noarch".
View 4 Replies View RelatedFor the past few days, the automatic GUI update has been crashing, complaining of a "Transaction error."
Here is the output that pops up in a separate window:
Code:
I tried the following:
Code:
And got the following (similar) output:
Code:
I very rarely use xfce and I don't quite know what exo is, but I'd like to fix this problem if it's not too involved.
Im running an update through YUM from my CentOS5 64bit box and came across this error:Transaction Check
Error:
I've done some research on this and found solutions on how to rectify (i.e. reconfig YUM repositories etc.) but still same issue.
I have fedora 12 dual boot windows/ xp on intel d845gvsr intel motherboard, intel celeron processor 2 ghz, inbuilt board graphics, 1 gb ddr1 RAM. I get this notification that updates available and when I try to download it it fails and I get the following error.
Transaction error.
"could not add package update for abrt-plugin-runapp-1.0.8-2.fc12(i686)updates: abrt-plugin-runapp-1.0.8-2.fc12.i686"
Have just installed Fedora 15 without any problems but when i tried to update the software i got the following error.
Transaction Error:
More Details:
Ok. Using Release 12 Constantine Gnome 2.28. Whenever I try to update my computer via de Software Update Manager that pops up every now and then I get an error and the Software Update fails.
The error says its a repository not found, but I am very new at this and have no clue as to where to fix this. Alongside of this, is the fact that since one of the updates is failing, the rest don't install either. So the updates keep on piling.
This is the error shown in the More Details window:
Code:
The details of the Unspecified Error are belowQuote:could not add package update for fedora-release-rawhide-15-3(noarch)updates: fedora-release-rawhide-15-3.noarchThe screnn shot attached of the error message!How will I able to get my system updated.After sometime it is today that I installed Fedora 15 and there are 316 updates to take place
View 5 Replies View RelatedI installed fedora 12 today...installation went fine. Tried to run the software update ( which includes 415 fixes) and got the following
Transaction error:- an unspecified transaction error has occurred. More information is available in the following report.
More details show:- could not add package update for abrt-plugin-runpp-1.0.4-1fc12(i686)updates:abrt-plugin-runapp-1.0.4-1.fc12.i686
I have unchecked the box in the update list to be installed, but the software update insists that this update is needed. I cannot progress any further than this error message..
I think I had this problem before but I don't remember what was done to correct it. I just tried to do an update and got this error message.
Code:
Test Transaction Errors: file /usr/lib/gstreamer-0.10/libgstfbdevsink.so from install of gstreamer-plugins-bad-free-extras-0.10.18-1.fc12.i686 conflicts with file from package gstreamer-plugins-bad-0.10.17-2.fc12.i686
file /usr/lib/gstreamer-0.10/libgstoss4audio.so from install of gstreamer-plugins-bad-free-extras-0.10.18-1.fc12.i686 conflicts with file from package gstreamer-plugins-bad-0.10.17-2.fc12.i686
file /usr/lib/gstreamer-0.10/libgstsdl.so from install of gstreamer-plugins-bad-free-extras-0.10.18-1.fc12.i686 conflicts with file from package gstreamer-plugins-bad-0.10.17-2.fc12.i686
file /usr/lib/gstreamer-0.10/libgstshapewipe.so from install of gstreamer-plugins-good-0.10.21-1.fc12.i686 conflicts with file from package gstreamer-plugins-bad-0.10.17-2.fc12.i686
file /usr/bin/gst-camera from install of gstreamer-plugins-bad-free-0.10.18-1.fc12.i686 conflicts with file from package gstreamer-plugins-bad-0.10.17-2.fc12.i686
file /usr/bin/gst-camera-perf from install of gstreamer-plugins-bad-f...
Getting "DBus error : Unable to get transaction id from packagekit." when trying to update. I can't update or install software through the package manager anymore. The yellow exclamation point won't go away on the toolbar.
View 8 Replies View RelatedWhile am updating using yum some error showing ... (am new in the field of cent os , and am doing these all job by ssh )
Dependencies Resolved
Transaction Summary
I switched from Ubuntu to Fedora and I'm having a little bit of trouble understanding why I cannot update my system. Fedora seems to be a little bit more complicated than Ubuntu to update and to do other things... I'm still willing to try it because it has a good reputation and good reviews so I will go ahead and give it a shot but before I do that I need to update it. I have an HP pavilion notebook dv2000. Just installed Fedora 15 and my system is telling me that I have over 700 updates! when I click on install updates I get an error:
Transaction error An unspecified transaction error has occurred. More information is available on the detailed report. Then on the details this is what I get:
[Code]....
I've been trying to update Fedora 15 for weeks. I always end up with a transaction error and the update stalls. The error reads: GPG keys listed for RPM Fusion for Fedora Rawhide-free repository are installed but they are not correct for this package. Check that the correct key urls are configured for this repository.
This is far too involved for a linux newbie, I think my only option is to reformat and reinstall. This is so frustrating, there are 250 MB of updates available that I can't access.
what is this, and more importantly, how do I fix it?
Quote:
Package Arch Version Repository Size
[Code].....
I'm trying to get the first update. I'm getting looped with "Transaction error," and it won't start.
View 2 Replies View RelatedFedora 15 software update "unspecified transaction error occurred" at system info before installing updated list. After unchecking every (no arch) update, all the rest (i686) were installed. now all (no arch)updates remain on the list to be installed.
View 1 Replies View RelatedThe error message is: "est Transaction Errors:
installing package kernel-debug-2.6.31.6-166.fc12.i686 needs 27MB on the /boot filesystem
installing package kernel-doc-2.6.31.6-166.fc12.noarch needs 27MB on the /boot filesystem
installing package setroubleshoot-2.2.50-1.fc12.i686 needs 27MB on the /boot filesystem
installing package perf-2.6.31.6-166.fc12.noarch needs 27MB on the /boot filesystem
installing package hunspell-1.2.8-13.fc12.i686 needs 27MB on the /boot filesystem
installing package gettext-0.17-16.fc12.i686 needs 27MB on the /boot filesystem"
I have boot as a separate partition, this time around I have set it to ext4 for the first time. That partition is only 250 Mb, but that has always been sufficient in the past, perhaps I am holding too many kernels or kernel versions?
When running yum update, I've been getting this:
Quote:
Good afternoon! I open software update and it find 10 updates! i go to install but it give me a messege: Code: libtool-2.4-4.fc15.i686 requires gcc = 4.6.0 : Success - empty transaction what can i do?
View 4 Replies View RelatedOn two Centos5 servers, yum gives a segmentation fault error when trying 'yum update' or 'yum check-update' after running 'yum clean' :
[Code]....
The error is the same for the other computer except while attempting to update the rpmforge repository. Nothing has really changed on the servers in some time and 'yum update' worked fine on each yesterday and I have no idea why they would both suddenly fail!
I've had my share of troubles with Ubuntu before and always been able to find help just by reading the forums, but this time it doesn't seem to be happening. Basically, I think I did something stupid by trying to change the permissions on my home folder to 777. (I'm the only person who uses my computer and got sick of always having to get root permissions.) Halfway through the process, the computer slowed to a crawl and text in dialog boxes started getting replaced with empty squares.
Naturally I rebooted - or tried to. Regular boot didn't work, so I tried recovery mode, which was kind enough to tell me I had a kernel panic because sbin/init wasn't found. Here's where things got weird: I then tried to boot from my Ubuntu USB stick, and couldn't. I got to the USB menu, hit the "run" option, and after a few seconds of the Ubuntu boot screen, my monitor went blank. Actually, to be technical, it didn't just show a black screen - the screen shut off. That's as far as I've been able to get.
By the way, just before I tried what I'm now calling the chmod-of-death, I also had an update freeze in the middle. I am able to boot into Windows, and have checked my USB stick - all seems fine. Any thoughts on this? Worst case, I can reformat the partition and reinstall, but I'd rather not lose all that data.
UPDATE: Okay, so I *did* manage, after about ten more tries, to boot from the USB stick. I went in from there and changed all the permissions back to 755. Tried to boot in recovery again, and still getting the same sbin/init error - so I'm wondering now if it had more to do with the failed update than the permission change....
I have a error when i want to update my system via YUMI execute the next command.sh@ yum -y updateYou could try using --skip-broken to work around the problemYou could try running:package-cleanup --problems package-cleanup --dupes rpm -Va --nofiles --nodigestThe program package-cleanup is found in the yum-utils package.
View 5 Replies View RelatedWhen trying to do an update or upgrade, I get the following:
Running Transaction Warning: RPMDB has been altered since the last yum transaction. Traceback (most recent call last):
[Code]....
I have tried yum clean all, yum clean metadata, rpm --rebuilddb, and even removing /var/cache/yum. yum info and yum list both work fine. Naturally, this yum problem is preventing me from updating my system.
Just when I thought I was getting my Ubuntu 10.04 system stabilized and really usable, the webcam magically stopped working. When I first installed 10.04, the webcam worked perfectly right out of the box. Tonight, I tried to start the video in a Skype conversation, and nothing. Video preferences in Skype showed no options for a camera. Rebooting the machine didn't help.
The one relevant thing I can think of that happened between the last time it worked and tonight is installing a number of updates. I'm not sure how to look up which packages were installed when -- I'm happy to run commands if someone can provide them.
Unfortunately, I don't remember how it was configured before. Since it was working, I didn't look at /dev to see where the camera shows up. At the moment, there is no /dev/video*. Clearly the system doesn't recognize that the camera is there, but it did before.. I don't recall device specifics. I looked online for a spec sheet that would say who is the webcam manufacturer, but I can only find the resolution. Tomorrow I have to boot into Windows to do some other work and I can get hardware info then.The machine is an MSI A6200 220US; the specs seem not to be available on MSI's website anymore.
Whenever I use yum after a recent update I get the message that I should run yum-complete-transaction.I have yum-utils installed but I keep getting the message that the command is not found.post the command I should be using to run it so I can see it it's just me typing the wrong thing into the shell?
View 4 Replies View RelatedWhen i do yum group install "KDE (K Desktop Environment)" i get
Transaction Check Error:
yum clean all
yum update gives this error:
Code:
It has been working until this. I shouldn't think that I need both the 586 and the 64 versions, but it won't let me get rid of the 586 version. Trying to do that results in:
Code:
Is trying to remove kdelibs-6:4.4.1-1.fc11.i586 what I should be doing? Or am I being dense?
When i was about to update it came up:
Code: DBus error : Unable to get transaction id from packagekit. Then it asked if i will start YaST and install the updates manual and i then took OK and this came up?
Code:
DBus error : Unable to get transaction id from packagekit.
After an udate I get this error message: DBus error : Unable to get transaction id from packagekit. This error also shows when I click the yellow triangle. When I start the manual update this shows:
[code]...
It seems some shell is not there anymore. What to do?