My server is DELL server. There are occur error about HDD (EXT3-fs error) more detail about the error
# dmesg
.
.
EXT3-fs error (device sdb1): ext3_lookup: unlinked inode 142214653 in dir #142213149
Aborting journal on device sdb1.
ext3_abort called.
[code]....
I decided to take an old Gateway that I bought off a guy cheaply and turn it into a file and web server.I purchased copies of Debian 5.0.4 i386 disks (31 in all) on the advice of a friend, the disks weren't expensive, but now that Ive installed all the disks, I'm having a variety of errors
[443.110940 end request: I/O error, dev hde, sector 76021855
[443.111074] EXT3-fs error (device hde1): ext3_get_inode_loc: unable to read inode block - inode=2375715, block=9502724
INIT: cannot execute "/sbin/getty"
[Code]..
I am running centos 5 on adaptec 2405 raid 10
PHP Code:
I get this error:
[code]....
I am using Wind River Linux- 2.6.27.18-WR3.0bg_standard. The problem is whenever I execute "reboot, ls, cd" and many other commands the OS prompts me an error-
"end request: i/o error, dev sda, sector "(different sector each time)" and
EXT3-fs error (device sda1):ext3_get_inode_loc:unable to read inode block- inode-4088001, block-4097027
I also executed "dmesg", it also showed similar errors. Has the disk gone bad or the kernel is corrupted?
I have an external usb disk connected to a Debian desktop. A couple of days ago these messages started appearing in dmesg
Code:
[154343.010908] EXT3-fs error (device sdb1): ext3_get_inode_loc: unable to read inode block - inode=14352940, block=57409572
[154343.014425] EXT3-fs error (device sdb1): ext3_find_entry: reading directory #13272620 offset 0
[154343.014913] EXT3-fs error (device sdb1): ext3_find_entry: reading directory #3440641 offset 0
[154343.022172] Buffer I/O error on device sdb1, logical block 53138974
[154343.022209] lost page write due to I/O error on sdb1
[154343.022218] Buffer I/O error on device sdb1, logical block 53138976
[154343.022252] lost page write due to I/O error on sdb1
[154343.022256] Buffer I/O error on device sdb1, logical block 53138977
When this appears the disk becomes unavailable and I have to remove and plug it in and mount again. After that it works couple of hour and then the problem appears again. Is this a hardware problem?
The external hard drive which contains all my photos and where I backed-up all my important documents is no longer recognized. It is a three month old 500GB Iomage Prestige Desktop Hard Drive.When I plug it in, it is recognised as a USB device, because it shows up when I type lsusb, but dmesg gives this error message.
[19712.013250] usb 2-2: new high speed USB device using ehci_hcd and address 21
[19712.145347] usb 2-2: configuration #1 chosen from 1 choice
[19712.147214] scsi25 : SCSI emulation for USB Mass Storage devices
[code]....
I popped the disk out of the casing put it on a SATA connect internally and then tried the file recovery programs testdisk/photorec and SpinRite, but both failed because they couldn't recognize the external hard disk.
I have a centOS 5 box with 3ware 8 port raid cards.I run fsck.ext3 -y /dev/sdb1 and it shows as clean.But after writing to the FS for about 2 minutes, it becomes read-only.When I umont -l /data, and run the fsck I get that another program is using the system an I should wait.If I reboot the server , the array comes back as clean.
View 2 Replies View RelatedI rebooted my server and out of nowhere the RAID5 array won't assemble. I've tried everything I could think of to reassemble the thing. I fear that the array is ruined, but I can't imagine how. Here are various bits of information: The simplest failure (with and without partition numbers, which have not been needed in the past):
Code:
richard@nas:~$ sudo mdadm --assemble --verbose /dev/md0 /dev/sd[bcd]
mdadm: looking for devices for /dev/md0
mdadm: cannot open device /dev/sdb: Device or resource busy
[code]...
Where is the inode table located in ext3 file system ? How can I read the entries in it ?
View 4 Replies View RelatedI'm using opensuse 11.1,syetm specification is following
CPU entium 4 2.93GHz
motherboard:asus
Hardisk:40 gb maxtor
Ram:1 GB
my system getting hang periodically after some time and the kernal showing the following error message
[Code]...
For backup purposes, I built a RAID6 array on USB. When during the night the backup filesystem is being mounted, every so many days, a random disk fails:
Code: sd 9:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 9:0:0:0: [sdb] Sense Key : Illegal Request [current]
sd 9:0:0:0: [sdb] Add. Sense: Invalid field in cdb[code].....
In other words, my RAID set fails every so many mounts, but I know how to fix it.What I want to find out is:
- Why is a random drive failed every now and then?
- How can I prevent that drive from being failed?
BTW: I have a second RAID set that has been functioning for years without error, so the setup I use must be correct. The only difference between both RAID arrays is the different vendor of the disks.
About a month and a half ago I purchased two new 500GB serial ATA hard drives from Best Buy to replace my other, very old 186GB SATA hard drive. Since then I've had issues with Linux. Sometimes when it's booting it gives a bunch of error messages, such as "failed to set xfermode," and then it boots. Other times, after INIT has started, I get ext3 errors about failing to read an inode block, then "cannot start /sbin/agetty" and "ID c5 respawning too fast," and at this point booting fails altogether. These errors seem to happen randomly. However, once the system has booted, everything seems to work fine, and there are no further issues.
I know it's not a faulty hard drive or filesystem because I've tried Linux on both hard drives numerous times, and I've reformatted many times, one time I even tried erasing one of the hard drives byte for byte and then formatting it, and still had issues.
I've tried Arch Linux, Gentoo, VectorLinux, and openSUSE, and all of them have given me these problems. The live CD's for Ubuntu 10.04, Clonezilla, and GParted all have trouble partitioning/cloning/installing to these hard drives. At this point, it's obvious to me that there is a universal problem with this particular model.
GRUB and Syslinux both work fine, and Windows XP works fine too. It's only Linux that's giving me issues.
I would rather not buy a new hard drive if I can help it, seeing as these two are almost brand new. Is there some BIOS setting that could be causing these problems? Is it some unsupported feature in the hard drives? Is it a bug in the Linux kernel?
The hard drive model is WD5000AADS. Both hard drives are this same model. My motherboard is an NForce 680i SLI.
EDIT: I've tried ext2/3, ReiserFS, and XFS, and all of them do this, so I don't think it's a filesystem issue.
I've been tasked with fixing a Red Hat system that dies with a kernel panic during the boot stage:
Code:
EXT3-fserror (dev sda1): ext3_check_descriptors: Inode bitmap for group 4 not in group (block 67239937)!
EXT3-fs: group descriptors corrupted!
mount: error mounting /dev/root on /sysroot as ext3: Invalid argument
I can boot into a Rescue CD, but I'm a bit out of my element because I don't use EXT3 myself, and I've never had to repair a corrupted file system before.
End_request: I/O error, dev sds, sector 420656157
EXT3-fs error (device sda2) : ext3_find_entry : reading directory # 52527153 offset
What is this Above Error which I am getting , on my server
I'm having trouble mounting hard drives and partitions - and am rather nervous about using Yast partitioner to do this. Is there something that would tell me about mount points in Yast partitioner? So far I haven't been able to find that information anywhere. I don't want to lose information on existing drives and partitions but do want to be able to access them.Some of them appear under disk information in "My Computer" but if I try to mount them I get this error message.There is no application installed that can open files of the type block device (inode/blockdevice).I was trying to edit fstab,his didn't seem straightforward either. I've been hacking this about in other Linux distros - so not entirely clueless
View 6 Replies View Relatedhave set up a server with OS on a 250GB disk (sdd) and 3x 1.5TB drives for a RAID5 storage setup (sda, sdb and sdc).Using webmin I can delete and create a primary partition in each one. But while I can also format sda and sdc, it refuses to do sdb for some reason:Executing command mkfs -t ext4 /dev/sdb1 ; partprobe ..mke2fs 1.41.11 (14-Mar-2010)
/dev/sdb1 is apparently in use by the system; will not make a filesystem here!
But I'm not using it
simon@ubuntu:~$ lsof | grep /dev/sdb
simon@ubuntu:~$ lsof | grep /dev/sdb1
[code]....
I have been using CentOS 5. for around 3 months. It was all fine and was having a pleasant experience using CentOS. Today when i turned on my computer and booted CentOS i am having the below error: Grub comes up, allows me to select CentOS 5.4 kernel image. and displays RedHat Nash version: and then the below error occurs:
[Code]....
I created a encrypted volume on top of software raid1. These are my steps:
1. Create logical partition on sda
2. Create logical partition on sdb (same size)
3. Change type to partition to 'fd' for both partitions
4. Check that the both partitions are same size and type fdisk -l /dev/sda && fdisk -l /dev/sdb
5. partprobe
6. Make sure there are no remains from previous RAID installations on /dev/sdb by running: mdadm --zero-superblock /dev/sda6 mdadm --zero-superblock /dev/sdb6
7. mdadm --create /dev/md4 --level=1 --raid-disks=2 /dev/sda6 /dev/sdb6
8. watch cat /proc/mdstat
9. update mdadm.conf mdadm --examine --scan | grep mdx >> /etc/mdadm.conf
10. Load twofish module [root@localhost ~]# modprobe twofish
11. # cryptsetup -y -c twofish-cbc-essiv:sha256 create ftdata /dev/md4 Enter passphrase: Verify passphrase:
12. mkfs.ext3 -b 4096 -R stride=8 /dev/mapper/ftdata
13. mkdir /ftdata
14. Mount the encrypted volume:
mount -O noatime /dev/mapper/ftdata /ftdata
It mounts successfully this first time. When I cd /ftdata, I can see the lost+found dir
[Code]....
So why is it that I can't mount my encrypted volume after the first time? I am giving the correct password when it asks to.
when i boot my system it gives an error ext3.0 and jbd.0 not installed/loaded
View 1 Replies View RelatedI am getting this error every night at 4am (right about when the cron.daily runs). when it does this, it remounts the filesystem read only. In the AM I get yelled at by users. all it takes is an fsck to fix the problem, but it does it every night. I have tried to rebuild the journal by removing the has_journal flag, running an fsck, and then re-adding the journal... same problem.. and its always the same inode.
View 2 Replies View RelatedI have added new member "i_mymember" to inode on-disk structure in ext3_fs.h file and tried to access this in userspace program, but gives me error that "error: �struct ext3_inode� has no member named �i_mymember� "
I have compiled my kernel source code.
why this error is coming ...?
I was using gparted from a live usb to resize an ext4 partition and it failed while running resize2fs. The error it gave was
Code:
resize2fs: The inode is from a bad block in the inode table while trying to resize /dev/sda5
please run 'e2fsck -fy /dev/sda5' to fix the filesystem after the aborted resize operation.
[code]...
I was trying to move my home partition on Ubuntu, and the computer hibernated on me. I restarted it up on the live disk to survey the damage, to find that the home partition, according to fsck, "Superblock has an invalid journal (inode Clear? <y>"
It cannot be mounted, either.
my server is fedora-7 and it was working fine till yesterday yester I have power failu problem after we got problem. while booting following error coming Inode 3640928 has a bad extended atribute block
View 1 Replies View RelatedI have HP ML350 G6 Server with RAID10 enabled on bios While trying to install Centos 5.5 64 bit OS I am getting the error mentioned below. "An Error Occured trying to initialize swap on device cciss/codop3. This problem is serious and the install cannot continue."
View 2 Replies View RelatedI'm having issues with getting my USB ports to work on my server. USB keyboards, mice, drives, flash drives, card readers, etc. will not work on this server.
dmesg
Linux version 2.6.18-194.32.1.el5 (mockbuild@builder10.centos.org) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-48)) #1 SMP Wed Jan 5 17:53:09 EST 2011
BIOS-provided physical RAM map:
[code]...
I had installed the CENT OS 5.3 it is installed when i rebooted it gives me error continuously.
Buffer I/O Error on device sda, Logical Block 0
ata4.00 : exception Emask 0x0 SAct 0x0 action 0x0 frozen ......
ata4.00 : status: { DRDY }
why it has giving the error.i have Intel based hardware Core II Duo with 1 GB ram check with sata hard drive 120 GB.
I just downloaded an iso of the latest CentOS dist (5.3) and burned it to disk. I booted from the CD and received the following error:
Memory for crash kernel (0x0 to 0x0) not within permissible range
Illegal mode for this track or incompatible medium -- (asc=0x64, ascq-0x00)
The failed "read 10" packet command was:
Buffer I/O error on device hdd, logical block 176935
(This error message repeats for another 9 or 10 times then it says the following)
Red Hat nash version 5.1.19.6 starting
Setting up new root fs
(Then there are some unmounts which are old /dev, /proc, /sys. At this point a series of steps begin).
Setting Clock
Starting udev
Loading default keymap (us)
Setting hostname local host.localdomain
Setting up logical volume management
Checking file systems
These are just some of the steps that appear after the above error is displayed, all of the steps that load have an ok status. After those are completed I get to a text prompt - localhost login: At this point my keyboard does not seem to respond, pressing enter or any of the other keys seems to have no effect. I noticed that during the load process I could toggle the light for caps and num lock, but at the login screen it does'nt work. So at this point I'm not sure if I'm having a technical issue or if its just another case of an user error.
I virtualized a PC with VMware vCenter Converter. But when I boot my virtual PC, I have an error.I found this link but I can't mount /dev, /sys and /proc. I have this error message : mount: /dev is not a block device.
View 2 Replies View Related1st. I lost my usb drives. Im using Puppy Studio(Lucid, Full HDD install, latest ver) on a Toshiba Satellite 2805-S201... My 1st Linux treasure... Anyway... I was recording audio thru audacity. Shutdown. L8r started and inserted a Flash drive and the icon never showed even though I used it hours prior with no issues. The drives are working fine meaning I can access the data on other devices. Now the newb... I cant find the USB info anywhere. i followed System-Status & Configure-Hardware info-Devices-USB devices and theres nothing there. The optical drive & sda1 are registered but the flash drives are not. Does it sound like my 2 USB ports are dead? My mouse & keyboard dont register either!
2nd. B4 today reboot was the only command I knew (so sad...) but I learned dmesg and tried that and dmesg reads
Ext2-fs (sda1): error: ext2_Lookup: deleted inode referenced 83359
Basically I now want to move my music but I have no working usb ports. And Its been frustrating trying to figure out what the dmesg means when today is the 1st time I opened a terminal!