Networking :: Network Doesn't Work If Cable Is Plugged In At Boot (Debian Lenny)?

Jan 19, 2010

For about the past month I have been having a very frustrating problem When I boot the system with the ethernet cable attached it acts as if the cable is unplugged even though the connection light is litWhen I boot the system with the ethernet cable disconnected and wait until it boots all the way to gnome and then plug in the cable everything works fine

View 1 Replies


ADVERTISEMENT

Ubuntu Networking :: Network Manager Replaces Default Route When Eth Cable Plugged

May 5, 2010

I have been encountering this problem, not only on 10.4, but on older versions too: I use a wifi router to connect my laptop to the Internet, but sometimes I need to connect directly to another computer to move some files over GLAN. But Ubuntu's Network manager doesn't allow me to configure the eth0 interface without specifying a gateway (no gateway = grey submit button), but when a gateway is specified, it always rewrites the default gw specified already by the active wifi connection and returns back after unplugging the eth cable.

Of course this can be solved by a few route commands, but this is unacceptable since it is needed to establish the cable connection without any further assistance from within and as well without replacing the default gw and thus breaking the Internet connection. Is there, please, any possibility how to prevent Network Manager from replacing these routes?

View 2 Replies View Related

Ubuntu Networking :: USB Tethering To Phone Doesn't Work Unless Phone Is Plugged In During Boot?

Jan 14, 2011

It's installed as a mobile broadband connection. Only works if my phone is plugged in during boot, otherwise plugging in my phone does nothing. For example, I booted my netbook earlier today but my phone wasn't plugged in. Tethering did not work, it just acts as if it isn't present. I rebooted (with my phone still attached) and now tethering magically works.

View 5 Replies View Related

Ubuntu :: When Ethernet Cable Is Plugged In / It Doesnt Work

Jan 27, 2011

When the ethernet cable is plugged in, it doesnt work. I have to unplug the cable, refresh the page and let it wait for the connection, after a second or two, i plug it back in, and it works. this works only for that page, which means only that page loads.. if i try to open another site or smthing else, it doesnt work and i have to repeat the exercise for the new site..i have to unplug, refresh and let it wait for connection and plug it back in.. The same thing happens if i try to download an application.. i have to first issue the command to download, and when it says "connecting to blah blah.." i plug the cable back in and it starts downloading, it doesnt work if the cable is already plugged it..!

View 9 Replies View Related

Software :: RDP Into Virtualbox When No Network Cable Is Plugged In?

Dec 15, 2010

I have a kubuntu 10.04 box and it runs virtualbox with windows 2000. For the most part, the network cable will be plugged in and i should be able to rdp into my windows 2000 install just fine, however, for testing purposes and for backup server testing, I will not have the cable plugged in all of the time.How would I rdp into that windows 2k install on the same machine if no cable is plugged into the ethernet port?I have both the kubuntu install and the windows 2k install setup with static ip's, but it is not working.

View 13 Replies View Related

General :: Automatically Connecting To A Network When The Cable Is Plugged In?

Apr 2, 2011

Is there a way to have linux connect to the network when the ethernet cable is plugged in? I'm using Gentoo Linux, and I haven't found the right setup for the conf/net that'll allow me to do that.

View 1 Replies View Related

Networking :: Not Getting IP When N/w Cable Plugged In

Dec 23, 2009

I am working on h/w device having linux kernel version 2.6.27 with busybox installed. I observed below problems while working on jffs2 image is flashed on the board.

1)When the board is powered-up with n/w cable is connected, it doesn't get IP address automatically, I have to use "/etc/init.d/networking restart" in init script(/etc/init.d/rcS) to get the IP address.(I am using dynamic addressing)

2)When the board is powered-up with n/w cable is unplugged and plugging-in once the device is started, I get "link up" message from the system, but still the IP is missing in eth0 interface.

I have udhcpc(v1.14.1) installed. Giving below commands manually, get the IP for device:

Code:
ifdown eth0
/etc/init.d/networking restart
but It is not pretty solution for me !

What I want is, the device should get IP address automatically once the n/w cable is plugged-in. (as we get in desktop m/c's). Am I missing some scripts or configuration parameters?

View 1 Replies View Related

Ubuntu Networking :: Auto Eht0 Doesn't Work - Can't Connect With Ethernet Cable?

Nov 13, 2010

I've recently bought a recycled computer for my office. The plan was to get an old cheap computer and use it to write LaTex documents but nothing else. However, I can't seem to get the thing to connect to the internet. I'm on a University network which has a funny setup but I don't think that's the problem.So here's the deal. I have tried this with 9.04, 10.04 and 10.10 and it hasn't worked. The computer recognizes the ethernet cable. If I issue the command "sudo mii-tool eth0" and get back "eth0: negotiated 100baseTx-FD, link ok". However, click on the networking logo on the top right, and click auto eth0, it tries to connect for about 30 seconds, then gives up. Unfortunately I'm pretty clueless when it comes to networking so I have no idea what to do to try to fix this.

View 8 Replies View Related

Debian Configuration :: Wireless Only Works When Ethernet Cable Is Plugged In?

Jul 9, 2011

I have a debian-powered NAS (Buffalo LinkStation) and I want to configure the following behaviour: When ethernet (eth0) is plugged in, connect and get a static ip address (ie. 192.168.0.11) When a wireless usb-adapter (wlan0) is plugged in, connect to a wireless router (ie. "Ankkanet") get another static ip address (192.168.0.12)

My /etc/network/interfaces :

auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static

[code]....

what could be causing wireless to disconnect when ethernet cable is unplugged?

View 3 Replies View Related

Debian Installation :: 5.0.3 'Lenny Missing Drivers \ Doesn't Work At All?

Feb 27, 2010

In reply to my last question about Wireless incompatibility in Debian 5.0.3 'Lenny', I found out it was because of missing drivers that I chose to ignore, despite the notifications.Now I've got this problem again, this time with different hardware and a different distribution of Debian (Debian Testing 'Squeeze' i386). As well as asking me to load up ipw2100-1.3.fw (of which I already have), it asks me to load tigon/tg3_tso5.bin. Loading the firmware is no problem. Finding and downloading nthe firmware is the problem here.I've searched through packacges and bug reports for a dowload link, but I've only come across a bundle with the driver I need, as well as a few unneeded extras. IT doesn't work at all.

View 1 Replies View Related

Ubuntu Networking :: Huawei E1752 Work Only When It's Plugged On The Boot

Aug 15, 2010

I want t understand why my 3G modem work only when it's plugged when my computer boot. If I forget to plug it , I need to restart my machine to get it working. I'm using ubuntu 10.04 when I plug the modem during the boot I get the product id changed from 1446 to 141b and dmesg |grep tty show me that the modem attached to ttyusb0 and ttyusb1 when I plug it after the startup I get also the product id changed from 1446 to 141b but dmesg |grep tty show me nothing.

View 9 Replies View Related

Networking :: Ethernet Cable And Wireless Network Won't Work In Ubuntu 9.10 / Sort It?

Feb 20, 2010

I'm a new user of Ubuntu, so i'm not that familiar with this OS. My wireless network is detected but when I'm entering my 128 bits WEP key, it doesn't connect at all. I have no clue where to start troubleshooting.

Here's some of my specs if that's of any help:
Computer is a Sony Vaio laptop model VGN-SZ370P
My wireless card is from Intel Corporation 82801G (ICH7 Family) USB UHCI Controller

The ethernet cable connection used to work before, but I fooled around with some commands and now seems to be disabled...

View 4 Replies View Related

Ubuntu Networking :: Laptop Locks Hard On Login Screen If No Ethernet Cable Plugged In

Jul 15, 2011

Acer 5250-BZ475 laptop, fresh install of Ubuntu 11.04. Boots up beautifully as long as an ethernet cable is plugged in. Otherwise, I get to the login screen and have just enough time to start typing in my password before the entire system hangs hard - no mouse, no keyboard, can't even get to a terminal, nothing. Have to hard power off the machine.

It seems to be a problem with the wireless card trying to initialize, but there doesn't seem to be a bios option to disable wireless on this laptop, so I'm a bit at a loss as to how to fix this problem. By the way, wireless works fine if I boot up with a cable connected - I can see all the wireless access points in my area no problem. I just can't boot without a wired connection, which makes my laptop more or less useless when I'm away from home with it.

View 8 Replies View Related

Debian :: Network Not Autoconnecting In Lenny On Boot?

Dec 26, 2010

I work at a public library, and am relatively new to Debian. Our OPACs (Online Public Access Catalogs) are running Debian Lenny. They are locked down to loading and visiting one specific webpage through a combination of Kiosktool and in the Opera browser.Initially, I had one machine set up with a static IP address, which worked just fine. Each machine has its own static IP which is translated at our Cisco ASA 5505 firewall to individual, physical IP addresses on the outside. However, I had many more machines that I wanted to clone from the working system.On the cloned machines, the physical network card in the machine shows up in ifconfig eth1, because it is "remembering" the eth0 network card from the master machine that it was cloned off ofNo problem, I thought, I will just change interfaces to the following:

auto lo
iface lo inet loopback
address 127.0.0.1

[code]...

View 3 Replies View Related

Debian :: Running Dnsmasq In Lenny - Wvdial Connecting But Dnsmasq Doesn't Work

Dec 30, 2010

I am running dnsmasq in debian lenny, wvdial connecting but dnsmasq doesn't work, the /var/run/dnsmasq/resolv.conf file is empty this is /var/log/syslog:

The /etc/resolv.conf and /etc/resolvconf/run/resolv.conf is ok:

This is my /etc/dnsmasq.conf:

[url]

View 3 Replies View Related

Ubuntu Networking :: Intel 82566MM "cable Not Plugged In"

Nov 5, 2010

have problems with my Intel 82566MM gigabit NIC. Using the default e1000e module. The module finds and load the nic but it doesn't recognize that i have plugged in cable or not. It always says "cable not plugged in". Using xubuntu now but same problem with regular ubuntu not that i think it matters. I tried downloading and installing e1000 from Intel but it doesn't seem to find the nic at all.

Any suggestions how to work this out? My googling says others too have had problems with this card. Couldn't find any real working solution though. Its Lenovo Thinkpad T61 laptop. Using 10.10 Maverick btw.

View 8 Replies View Related

Ubuntu Multimedia :: USB Video Capture Device Doesn't Work When Plugged In?

Sep 25, 2010

In Ubuntu 9.10, I was successfully able to use my Pinnacle Dazzle DVC 100 (a cheap USB analog video capture device). I use it for backing up old video that is stored on tapes, and it isn't working with my current install of Ubuntu 10.04. When I plug the device in, it should be detected and the em28xx module should be loaded. This fails and /var/log/messages has the following:

Code:
Sep 25 16:13:18 kernel: [1196215.111898] usb 2-2: new high speed USB device using ehci_hcd and address 20
Sep 25 16:13:18 kernel: [1196215.266097] usb 2-2: configuration #1 chosen from 1 choice

[code]....

View 3 Replies View Related

Ubuntu :: Remote Doesn't Work Without Keyboard / Mouse Plugged In - Restore Its Functionality?

Oct 11, 2010

I (finally!) have Mythtv working under 10.04. I use the Haupaugge DVB-T card with its remote. Whilst setting up the kit this worked OK. When I unplugged the keyboard and mouse the system prior to installing it next to the TV appeared to have stopped responding to the remote. In fact it seems to be responding to a number of the remote keys but not the OK and Go keys which isn't enough to run Mythtv.

I don't think leaving a keyboard & mouse plugged in is going to be domestically acceptable.

Does anyone have any ideas as to how to restore lirc functionality?

View 1 Replies View Related

General :: Windows 7 X64 Doesn't Boot If A Drive Is Plugged?

Jun 2, 2011

I have connected (sata cable I mean) the drive where I have got my Ubuntu installation to another pc with windows 7 64 bits (but I think that 32 and 64 doesn't make difference). Windows 7 doesn't boot. So I thought it may be some kind of issue with the hard drive itself (but the drive is healthy), anyway I have plugged one drive from one NAS (you know, NAS drives are linux partitioned and formatted).Same result: windows 7 doesn't boot.

Windows 7 boot sequence hangs and at the next boot prompts
"Repair windows installation"
"Boot windows normally"
(and obviously none of the options works)

Looks really like that Windows 7 doesn't boot if any linux partitioned and formatted drive is present.

View 12 Replies View Related

Ubuntu :: Server Boot - Doesn't Start-up Unless A Monitor Was Plugged In

Jul 19, 2011

I have an old computer (Pentium 4) without a monitor. To make the most of it I installed Ubuntu server on it and have been using it for almost a year. A couple of months ago I don't really recall what I did but since then it doesn't start-up unless a monitor was plugged in.

I've tried pinging it but it doesn't respond when no monitor is plugged in. meaning it's not even booting correctly.

I'd like to know what the problem is and how to fix it. And I'd really appreciate any help in diagnosing the problem. I just don't know where to start.

View 3 Replies View Related

Ubuntu Networking :: 10.4 Network Doesn't Work Due To DNS

Jun 15, 2011

i've installed it on my parents old computer, mostly for downloading. But wired internet did work all the time but then i had to reset our router because of some problems and now it doesn't work anymore! But the strange thing is, if i put the cable on my own laptop with windows on it, then it works as normal.

So i guess its some kind of DNS problem, but i'm very new with ubuntu and also not so good with computers. Our network is simple just an modem connected to an router: Sitecome WL-341.

View 4 Replies View Related

Networking :: Second Network Interface Doesn't Work?

Jul 3, 2010

I have two simultaneous active mobile connections through my two mobile phones and USB data cables. Yet I can only send/receive with one connection.Each of the phone modems have a node in /dev, namely ttyACM0 and ttyACM0. So the modems are detected correctly.After setting up two dial-up connections with the two modems I have two ip's. Ifconfig-a confirms this:

ppp0 Link encap:Point-to-Point Protocol
inet addr:10.10.219.60 P-t-P:10.6.6.6 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1

[code]....

View 1 Replies View Related

Ubuntu Multimedia :: Tevii S650 Showing Signal When No Cable Plugged In

Oct 28, 2010

I am trying to get my tevii650 usb DVB-S2 tuner working. I seem to have installed all the correct drivers as far as I can tell.

When I scan for services and then use femon to look at the signal strength femon -H, I get a signal of around 83% with 0 SNR and BER. Then if I remove the feed the signal goes UP to 97% 0SNR and BER.

I am trying to monitor signal the signal level coming down from the satellite. I don't even want to be able to tune to any of the channels. Basically I want to use the PC as a glorified signal meter and datalogger.

View 1 Replies View Related

Ubuntu Networking :: .04 - Wired Network Doesn't Work

May 4, 2010

I installed Ubuntu10.04, It cannot driver Wired network and wireless. Later I installed linuxMint9, wireless is ok, but wired network doesn't work. I am sure the lan cable is ok. It works in Windows.

View 3 Replies View Related

Ubuntu Networking :: Wired Network Sometimes Doesn't Work

Feb 14, 2011

what is the command to restart the network services? ive forgotten i think it uses -hup switch though. about 1 in 20 boots on my desktop ubuntu system results in the system insisting its no longer on a network yet has a fully functioning network card. a reboot always fixes the issue but that doesnt seem like a long term solution to me. If I ping a neighbouring system I get nothing. (sent packet count increases in ifconfig) If I ping from a neighbouring system back to my desktop I get nothing (no change in packet count) I can bring down and back up the network interface with no results. A sniffer shows the system definitely isnt sending anything out Everything worked previous boot and will work again after a reboot.

View 2 Replies View Related

Ubuntu Networking :: Network For Lenovo T400 Doesn't Work

Feb 22, 2010

I just got a new T400 and installed Ubuntu. Everything is fine and I'm really impressed by this OS. But seems my wireless network is very unstable. Sometimes it just can't connect.

The wireless interface is:

description: Wireless interface
product: PRO/Wireless 5100 AGN [Shiloh] Network Connection
vendor: Intel Corporation

View 2 Replies View Related

Ubuntu Networking :: Wireless Doesn't Work - But Recognizes Network?

Sep 20, 2010

I installed Ubuntu on a machine after erasing everything else and the wireless has never worked. It says that the wireless has already shut down even though it recognizes the wireless network and my other non-linux machines see the network and work fine.

View 1 Replies View Related

Ubuntu Networking :: Wired Network Doesn't Work (HWaddr 00:00:00:00:00:00)?

Dec 6, 2010

My desktop PC has 2 NICs. I have Ubuntu on it since several years, and I remember that both eth0 and eth1 used to work. However, I discovered recently that currently only eth0 works, and eth1 is dead, but I don't know why. It's been a while since I've tried eth1, so I have no idea when exactly it broke. I suspect the problem may be related to the fact that the MAC address is incorrect: it is set to 00:00:00:00:00:00, which seems wrong. But I have no idea how this happened...Any idea what might be wrong and how I can fix it? Here is some output which I think is useful:

Code:
peter@cheetah:~$ ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:18:f3:68:42:78

[code]....

View 9 Replies View Related

Ubuntu :: Headphones / 2.1 Sound System Doesn't Work After Jack Is Plugged In Ubuntu 10.10

Feb 2, 2011

I`m new to Ubuntu and Linux as all. First of all i have a Dell Inspiron N5010 laptop. I have a very strange problem, after the initial installation of Ubuntu 10.10 there were no problems plugging in my headphones or 2.1 sound system and listening to music. After a couple of days when trying to plug in my 2.1 sound system I noticed that there is no sound coming out of them, but the laptop speakers were working fine. Tested the sound system with another laptop and they worked well. I have checked all the settings and everything seems fine. I`m puzzled. I have the system dual boot with Win 7 if that makes any difference.

View 3 Replies View Related

Debian Installation :: Boot - Apt-get Install Xorg Doesn't Work

Mar 25, 2010

I recently installed debian on my ibook G4, but when I start up the computer, it doesn't boot into Xorg. When I tried to start Xorg, it says that it is not installed. How would I install it, and how would I start it? When I do the apt-get install xorg, it doesn't work. Right now I'm running ubuntu on it, but I really want just plain debian, as I really dont need all of the bells and whistles that Ubuntu offers. I just need something to do schoolwork on (I'm a highschool sophmore), and I don't want to use OS X for that as I like linux better (specifically debian and ubuntu).

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved