I am going back to Windows for good. All I need to know is what are the partitions settings so that it will be reconized able in windows. I planning on saving some of my songs and other media that I have collected but I dont want loss all of on some wasted space that isnt readable. So simply put what setting are needed to make a partition visible in windows 7 using gparted.
View 1 Replies
I'm currently working on fixing another problem url
I have a 60 g internal laptop hard drive, 30g is Windows 7 and 30g is Ubuntu.
When in Ubunutu I can access the window's driver and mount it, however, when I am in windows 7 it only shows the Window's partition.
Is there a simple way I can get the ubunutu partition to show up>
What partition type does Mac OS X use, and can gparted create one?
View 6 Replies View RelatedI have 3 partitions on my hdd right now, a Windows 7 one, the associated System Reserved and my Linux Mint partition. I was trying to use GParted to make another partition by splitting my Linux Mint one in two smaller partitions. I can't, however, unmount it, and so can't partitions it. I have considered partitioning it from Windows 7, but I'm afraid it will screw some things up and stop booting up correctly. So, what could be making the partition unable to unmount?
View 11 Replies View RelatedI downloaded gparted. i would really like to make my ubuntu partition bigger, i've got over 200 gigs of free space on my windows partition. i've played with it some and cannot seem to figure out what to do.
View 5 Replies View Relatedhow to upgrade my ubuntu 9.10 system. I would like to do a clean install of lucid, but I have way too many files. I have a big hard drive, so space was not a problem, and things got out of hand ^^ One thing you should know is that I have plenty of room for my files even if the drive was half it's size, so my idea is possible space-wise. (And I am prepared if this fails. I have backed up my stuff, but would like if it I didn't have to rely on that)
What I want to do is make a blank partition with gparted and install lucid on it. Then I want to keep it a dual boot just to make sure my hardware is working ok, then move my home folder to the new partition, make the lucid partition take the whole hard drive, and delete karmic. I do not want to upgrade because I messed up my install a lot while learning linux, so I really need to start over.
I was resizing my windows partition and accidently turned my computer off. When I went to run a disk check from gparted I get multiple filesystem errors. Chkdsk /r when run from a recovery cd says it can't determine the size of the partition so it can't continue. Is there anyway to get my files off the corrupted partition from within linux. Right now Gparted shows that it has been resized but that it is corrupted and i can't even attempt to mount it. There are only a few files I need to get off the partition but they are really important.
View 3 Replies View RelatedI was trying to remove my windows partition using the live CD. While Windows no longer works on my system, GParted shows that I still have 40 gb of unallocated space. Have I not properly occupied the space left after I removed the Windows partition.
View 8 Replies View RelatedI'm trying to add more memory to Ubuntu from my windows partition, but Gparted doesn't seem to recognize the windows partiton. I've done it before using the gparted live cd, so i don't know why it wont recognize the partition. Is there some way to mount it so I can move space around?
View 9 Replies View Related10 yr old Dell laptop with NO WORKING DRIVES. i was dual booting xp and xubuntu when i decided it was time to cut the cord. so i installed gparted and deleted my windows partition. now it won't boot. my assumption is that i never installed grub. i got a usb to ide cable so i can access the hard drive from my desktop (xp home edition). i read that grub should be in a folder called "boot". i see on my hard drive that i have: "disks", "winboot" "install", "uninstall-wubi.exe", and "xubuntu.ico". if i expand the "disks" folder, there is a "boot" folder containing another folder called "grub", but the folder is empty. is this where i install it? am i an idiot and missing something stupid? where do i download grub if i need it?
View 9 Replies View RelatedSo far I've been dual-booting Vista and Intrepid, and I decided I'd shrink down the Linux partition a bit, expand the Windows partition and reinstall Ubuntu fresh from a Live CD. I booted up from a Live CD, mounted the old Linux filesystem to check that I hadn't missed any documents to back up before I wiped the partition, and then cued up the relevant operations in GParted.
The key mistake I made was not to unmount the old Linux partition first, which led GParted to bug out and, apparently, stop my Windows partition from working. GParted no longer recognises the partition as NTFS - it tells me it's an unknown filesystem, and refuses to move or resize it.
sudo fdisk -l recognises the partition as HPFS/NTFS. Running chkdsk from a Vista recovery disk has been, so far, unsuccessful. What else can I do to either make the partition bootable again, or at least access it from Linux so I can pull my files off?
I realise that this is not a pure Linux Q, but I am hoping for tolerance and even help!After removing the partitions (/,/home) that held an older Linux installation, gparted showed the original Windows XP partition followed by the new unallocated space. On rebooting, there was a Grub rescue error (text not noted, sorry). A live install running gparted shows a totally empty disk!
The removed OS was booted via Grub2 and I imagine that it is choking when there is no secondary(?) file to be found since it was vaped. I also imagine that this is a fairly straight-forward matter, something like replacing the MBR but I am so far from Windows these days that I am unsure how to progress with rescuing the partition. The machine has no floppy - that's how I would have initially booted it way back when. Is this something that I can do either through a Linux live distro or via a Windows CD?
I've been trying to use GParted Live CD to shrink my Windows XP partition and allocate this space to /home.
On GParted I shrank my /dev/sda1 (Windows) from 36GB to 26 GB. Then I had 10 GB of unallocated space. I didn't know how I could use this unallocated space to increase the size of /dev/sda7 (/home). How do you do this?
I have a 230GB hard drive wich I don't know it's name.I have a 207GB windows vista partition and the rest of it is for linux (Ubuntu).Today I decided giving it all space to Ubuntu Linux ,but didn't want to lose all my data from the windows partition.I thought that by deleting all things except the folder with my data and leaving enough space to shrink and make enough room for another partition to put my data folder.The logic is that i could then format that partition wich previously was windows and use it all for ubuntu without losing data.After having ubuntu installed i could copy my data folder to /home and then delete the previous partition and make /home bigger.The problem is that after i freed the space,when using Gparted to shrink it says that the partition has bad sectors or the filesystem has problems and so it can't do some operations.
What could have went wrong?It told me to do chkdisk but as i deleted all the windows files and i can't boot into it anymore.I used the vista dvd to do that.I rebooted 2 times as it says and after that when trying again nothing changed.I tried to use ntfsresize with the --bad-sectors argument and also the -f argument but it's useless.At the end it says it won't do anything until the ntfs filesystem get repaired.Or it says it is too risky to continueIs there any way i could do some superforce command to resize it without losing data?Please don't tell me to put it on an external storage cause i have like 70GB of datas to save...no i don't have an external hardrive
After I formated my windows partition using GParted it became Unallocated and moved under Extended partitions. I can't create the unallocated partition as primary one, or drag it out of the extended ones. I tried GParted live CD also, but nothing worked.
View 7 Replies View RelatedI have 3 Ubuntu installations & a PCLINUXOS, plus Windows XP installed on one hard disk. I still can boot to each one of them and can mount each one using Ubuntu.
The problem "may" have occurred when I reduced the size of some linux partitions using gparted. I still have plenty of space in each of those partitions.
When I started gparted all of the HD was unallocated. I did that from each ubuntu installation and the PCLINUX installation, plus LIVECDs. All indicated the space was unallocated.
When I did an fdisk -l from a Puppy Linux LiveCD I got a normal start and ends of each partition.
When I tried it from Ubuntu installation or live cd, I received the following types of responses:
Code:
ubuntu@ubuntu:~$ sudo fdisk -l /dev/sda5
Disk /dev/sda5: 28.5 GB, 28566397440 bytes
255 heads, 63 sectors/track, 3473 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x00000000
Device Boot Start End Blocks Id System
ubuntu@ubuntu:~$ sudo fdisk -u /dev/sda5
The number of cylinders for this disk is set to 3473.There is nothing wrong with that, but this is larger than 1024,and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs (e.g., DOS FDISK, OS/2 FDISK) Plus the Windows partition seems to go over its limits.
Since all of my OS installations are still working, I don't know how critical this is. From reading another post, I understand this might be able to be fixed by making some changes in fstab.
i am following the installation process and its very unclear whether or not a dual boot will occur and how i can make a partition of the free space available from my windows partition etc....i dont want to go through the process and find myself losing all my data and my windows partition i also cant seem to select a partition less than 86% of the total capacity of hdd so im def sure they're not taking my dual boot desires into consideration.
View 1 Replies View RelatedI've been using Ubuntu 10.10 for just under a week. Recently, a partition called 'Data' has disappeared, and all my music and documents along with it. The folder is not to be seen in Places or on my desktop. My only way of finding it is to go to terminal. But when I try to open it there I get an error saying I don't have permission to read it. In Puppy Linux and SliTaz I can easily find the partition and read it. What should I do to bring it back in Ubuntu?
View 3 Replies View RelatedMy ubuntu crashed..i dint hav a live cd.now my remastersys backup ws der in other ubuntu ext4 drive.now when i hav installed windows to recover that backup that file to install ubuntu again.im not able to see that drive.
View 3 Replies View RelatedI was reading another thread about someone with a bad partition table and I decided to join this forum. I'm not going to take any drastic actions with the partition (/dev/sda3) in question. I am going to wait for instructions on what to do first. I am not very good with Linux and need some hand holding. System: DELL 4550 Dual-Booted with XP and Ubuntu. Works OK, just no swap. Well, here's what I did: I deleted a partition for Windows XP Pro because it was a trial, and it ran out. I then decided to slide the swap partition for the Ubuntu Linux that I dual-boot into over. (If this was successful, I was going to try expanding the root partition to take up the unused space.) I used Gparted on a CD to do this, as I figured it was safe to do.
I now cannot mount the swap space at bootup (and have to go into a backup version of the OS), although I can use Gparted in Linux to execute the "swapon" command, and it appears that it worked because I now see "swapoff" as an option on the context menu. (I actually don't even need a swap partition, except to hibernate.) If I highlight the swap partition and click on "Drive" on Gparted's menu bar and select "Create Partition Table", it will erase all data on /dev/sda, so how do I fix the bad partition table non-destructively?
I usually repartition a disk by backing up, deleting the partitions, formatting them and repartition. I just did a 200 gig backup (so i am safe) and i want to join 2 (ext3) partition together, sdb1 (data4) and sdb5 (data5) into one big partition. Is there a way to do it without scraping the data in sdb5 (data5). It would save me from rewriting the data back to that new partition (200 gig is time consuming).
View 1 Replies View RelatedI recently installed ubuntu alongside windows 7 on my machine. I ardly know anything about partitions, but I managed to shrink the windows partition to make space, abd then use the ubuntu installer to create the ubuntu partition. But I hadn't realized that there were actually 3 Windows partitions - "Acer C:", "Recovery", and "System, Active, Primary Partition".
So I didn't know that I should have made the ubuntu partition "Extended", which means that I can't make new partitions anymore. Is there anything I can do without reinstalling ubuntu?
I downloaded Ubuntu Server. I absolutely love it. It is easy to set up and I've already learned alot while doing so.
Now, I want to get a bit further. I want my Ubuntu Server to be accessible from the internet, so I can access my files and webpages from everywhere.
Everything works locally, but I don't have any clue to maken it visible for WAN. Is everything from here set in the router settings? Or will I also have to make adjustments in the Server's settings?
Currently have a dual boot HTPC running windows 7 & ubuntu 9.10 , windows pulled "no longer a valid"on me after an update an i was left with a limited machine. I figure now is as good time as any to go full with a fully linux system. However, i am having some problems.
1) Windows 7 needs purged from my system.. like a cancer. I need to get rid of my sda1 windows partition. I gathered i will need gparted and grub2.. But will i need a Gpart liveCD? I need someone to take my though it.
I got and ran Gparted. My system seems to have 3 partitions with 2 unallocated spaces.
2) I will need to remount the windows partition after i reformate it and get rid of windows. I will likely need help with this as well. believe it is also worth noting that i believe wubi was used to put Ubuntu on this machine.
I want to make it now because it is still under the size of a dvd 3.7GB and i want to put it safe on a dvd to restore fast and not have to customize anything in case of a disaster , like me running dd again )
View 14 Replies View Relatedi cant seem to find an option for this. im trying out mint and want to play music and videos but they are on a USB which i cant access.
View 9 Replies View RelatedI have Wlan available but I cannot connect to itI don't have wire network available so I can't connect to internet at allI'm writing this trough dual boot (win)how to make network manager visible so I can choose witch Wlan connect to?SOLVED:Quote:Originally Posted by gandaranif the network manager panel icon is missing all you have to do to get it back is right click on the empty panel area where you want it to bechoose add to panel and select the notification area applet and click add.
View 7 Replies View RelatedI recently switched from Ubuntu to Kubuntu (fresh install of the OS, not just installing KDE), and I'm more than a little lost. When I download files to the desktop, they don't appear on the Desktop. I can see that they're in /home/andrew/Desktop through Dolphin, but the icons just aren't there. I was able to successfully put an icon for Firefox, but the icons for these files just aren't showing up. I can't help but think it might just be due to a setting, but for the life of me I absolutely can't find it and I've been googling to no avail. how to make files visible on the desktop?
View 5 Replies View RelatedSomewhere during my installation, I forgot to make my Windows partition (as well as a drive that linux associates with Windows) writable. Is there any way to make them writable, without re-installing everything?
View 9 Replies View RelatedI have a dual boot with ubuntu 10.04 (ext4) and ubuntu 9.04 (ext3).On 10.04 I accidentally deleted a whole bunch of files with the rm command. I installed extundelete in 9.04 which can undelete from ext4 file systems. However, I can't access my 10.04 home directory in 9.04, as /media/disk/home/asdf is empty except for two files README.txt and Access-Your-Private-Data.desktop. I didn't delete all of it for sure.
Does anyone know how to make my 10.04 home directory visible in 9.04 so I can undelete?
