Ubuntu :: External SATA Transfer Speeds?
Mar 26, 2010
I just bought a 1Tb hdd and reformatted to FAT32 it is connected via eSATA to SATA cable.At first I transfered music that initially was getting speeds over 100mb/s (according to nautilus) after about a minute it started to dwindle. Now most files will range somewhere between 8-20mb/s although I've only seen a couple go beyond.i edited hdparm.conf to enable DMAHere is the output of hdparm -Tt for both internal(sda) and external(sdb) hardrives.
Code:
/dev/sda:
Timing cached reads: 14872 MB in 2.00 seconds = 7444.68 MB/sec
Timing buffered disk reads: 372 MB in 3.00 seconds = 123.91 MB/sec[code]....
What is the issue this output leads me to believe that I should be getting the same speed I once got.I'm running Intel Core 2 duo at 3.00, ASUS P5Q (enabled AHCI) and 4gb ram 12gb linux swap. Also Karmic 9.10
View 1 Replies
ADVERTISEMENT
May 1, 2011
I keep getting this error in my log viewer every 2 seconds: Code: ata4: limiting SATA link speed to 1.5 Gbps I have a dual boot SSD and I have run many SMART tests in windows and linux, (using smartmon tools and the disk utility) and the reports are all 100% healthy..... My research shows that this error represents one of the following:
1. Problem with SATA controller
2. Changing BIOS to allow SATA
3. Changing SATA mode to PATA or AHCI
4. Replacing the SATA cable
5. Allowing the SSD to run at SATA II speeds, i.e. 3 Gbps
- Does anyone know how to try number 5, i.e. allowing the SSD to run at SATA II speeds? I am lost here and this problem has caused my machine to crash twice when watching a movie in linux/ ubuntu. (It is worth noting that the crashes have only occurred in linux and I have never had an issue in windows, so it does seem to be a linux setting somewhere, hence why I think it is a "allowing SATA II to run at correct speeds issue")
View 4 Replies
View Related
Jul 4, 2010
My friend bought an old hard drive. He noticed something with the hard drive that it was just replaced with a SATA socket. So meaning, the SATA socket was soldered to the PATA hard disk to replace the PATA socket to SATA socket to make it a SATA.
Now the question is:
1. Does the Transfer Rate of the harddisk (that has been replaced from PATA socket to SATA socket) would be SATA transfer rate? OR would still be PATA transfer rate?
View 4 Replies
View Related
Apr 6, 2011
I have read many threads but cannot find a solution on this code...
Now no matter how i transfer if its from HDD to HDD or to SSD i never get more then 18-20MB/sec, i just tried booting to my live CD and was able to transfer with 24-25MB/sec
This is really slow, since the worst (2.0TB) can do a minimum of 30 READ
Anybody got any ideas, this seems to be something that has plagued ubuntu for years, and no i don't want to try other distros, i tried almost all of them a year ago and finally went with ubuntu
View 9 Replies
View Related
Dec 27, 2010
I'm at the end of my rope here. And the most frustrating part is, I've found many posts all over the web from others who have had similar problems, but they ALL seem to be older distros and those solutions don't work for me. "Find Similar Threads" only yields one thread, and I don't have the file mentioned in the answer (the original poster didn't either).
Computer: AMD 64 Quad core, USB 2.0 on front bus, dual booting Vista and Ubuntu 10.10
Device: New Sansa Clip+ 8GB mp3 player
Problem: When I transfer files to my mp3 player in Ubuntu, I max out at about 150 KiBbps. It's painfully slow - it takes me half an hour to transfer 300 MB worth of albums. I had similar problems with an older player that may have been usb 1.1, but this one is brand new. And when I switched to Vista (first time in months, thankfully), I was able to transfer the same files at upwards of 3 MBps. I know that flash devices often can't write anywhere near the max speed of USB 2.0, but obviously it can do a whole lot better then 150 KiBps!So, same hardware, same files, different OS - the problem must be with my Ubuntu config.
View 13 Replies
View Related
Dec 14, 2010
I tried using my USB to transfer a 500MB file, the speed came up as 1-130 kb/s. That is pathetic. I should be getting more 25MB/s.
View 14 Replies
View Related
Aug 4, 2010
I've just managed to access my windows share from Ubuntu but am now getting write speeds (to xp share) of only 9MB/s over my wired network, anyone have any ideas as to why this may be? I've googled but can find no specific answer.
My NIC is:
Ethernet controller: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe (rev 10)
(from lspci) on a Dell studio 1737)
View 3 Replies
View Related
May 24, 2010
My wireless network is giving me a fit. Slow transfer speeds and then I lose connection and have to reboot.
greg@greg-computer:~$ /sbin/ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:92 errors:0 dropped:0 overruns:0 frame:0
TX packets:92 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:10214 (10.2 KB) TX bytes:10214 (10.2 KB)
wlan0 Link encap:Ethernet HWaddr 00:16:b6:5a:9c:a5
inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::216:b6ff:fe5a:9ca5/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:13085 errors:0 dropped:0 overruns:0 frame:0
TX packets:9600 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:15268450 (15.2 MB) TX bytes:2704035 (2.7 MB)
wmaster0 Link encap:UNSPEC HWaddr 00-16-B6-5A-9C-A5-00-00-00-00-00-00-00-00-00-00
UP RUNNING MTU:0 Metric:1
RX packets: 0 errors:0 dropped:0 overruns:0 frame:0
TX packets: 0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes: 0 (0.0 B) TX bytes:0 (0.0 B)
greg@greg-computer:~$ netstat -rn
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0
169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 wlan0
0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 wlan0
greg@greg-computer:~$ cat /etc/resolv.conf
# Generated by NetworkManager
nameserver 192.168.1.1
greg@greg-computer:~$
View 1 Replies
View Related
Dec 13, 2010
About NFS.
Server:
Client(s):
Code:
I have followed Robbie Workmans' HowTo [url]
Reading and writing works absolutely fine with small files but large files are tediously slow in writing to the server. (rw,no_subtree_check) are options in exported directories.
What is your experience with NFS and how can I speed up large file/folder transfer(write) speeds?
View 5 Replies
View Related
Feb 12, 2016
I'm having a strange problem with data transfers between systems. I have a file server + my desktop. Both are running Debian 8.3. I have a samba share running on the file server and I mount the shares on my desktop on boot via /etc/fstab
When I copy a file using the nautilus from my home folder (on my HDD) on my desktop to the mounted network location, my transfers start out at gigabit speeds 80MB/s-90MB/s for a couple seconds and then drop down to about 8MB/s
But when I terminate the transfer and then use scp to transfer the same file, I get consistent gigabit speed throughout the transfer. I am not sure what is going on.
View 2 Replies
View Related
Jan 25, 2010
Is there a device that would allow me to transfer files from my old IDE hdd to a new SATA hdd? My computer died (motherboard, possibly ram and psu) with my files trapped on my old IDE hdd. I do have a backup on DVD, but it is a little old. Thus, I would like to get the current files on the IDE hdd and either transfer them to a SATA hdd or burn them to DVD.
View 3 Replies
View Related
Oct 11, 2010
I'm trying to back up my hard drive to a 2 TB WD external so that I can do a clean install of 10.10, however I'm getting tremendously slow write speeds. It hovers around 1.5 MB/s and steadily slows from there. It tells me it will take 150+ hours to transfer 400 GB of data.
I have a AMD quad core processor and 8 gigs of ddr3 ram... USB 2.0... I feel this should go much faster.
View 5 Replies
View Related
Sep 30, 2010
When I copy files to my External NTFS HDD using Ubuntu the write speeds are about 10-12 MB/sec, but when I copy files using Windows the write speeds are about 25-30 MB/sec.
Exact same files, tried all three ports on my netbook and even timed it to see if the speeds are by any chance miscalculated by either operating system and Ubuntu is definitely writing at half the speed.
So what could be the problem? When I had Windows on this Netbook I never got had a problem with write speeds so I don't think it is a hardware issue.
View 1 Replies
View Related
Apr 17, 2011
Whenever I transfer a movie into my 16GB USB flash disk, my whole system becomes windows-like and unusable!
When i drag the file(s) into the USB disk folder, it starts out fine and pretty darn fast (25mb/sec) then slowly decreases until it's unbearably slow (3m/sec) and as a side effect my whole system starts deteriorating. I basically have to wait for the file to finish transferring before i can use my desktop again!
This has been happening with every version since Karmic (all 64bit)- I put up with it because I don't use the USB stick that much.. but lately it's been my go to source for transfering large files to/from work.
View 3 Replies
View Related
Jul 8, 2011
I have landed myself in a bit of a pickle. Needing to upgrade my system for 11.4 I went ahead and bought a refurbished Compaq. The intention was to merely replace the smaller drive with my existing drive. Only problem is that on opening the Compaq I found a SATA drive. Being a Compaq there is no space for a second drive, so I must copy my existing system via CDROM. As the 11.4 has gone through a number of updates since I installed, I cannot use the original installation CD. Downloading is out of the question for my link speed. I made an automatic backup when installing but am not sure where it is or whether it is also kept up to date. Anyway, does the backup contain merely the system and then require further transfer of home folders, etc? The alternative, of course, is to source locally the latest version that will not require hours of updating.
View 6 Replies
View Related
Jun 21, 2010
I have a 9.10 fully updated install on an old P4 HP desktop that otherwise runs flawlessly. We moved it to the bedroom to use as a media center and when I plug in a Thermolake toaster with a Hitachi 750G SATA drive it is recoginized and available no problem. I can read/write no problem. It works via nfs4 no problem. The issue is if I reboot while the drive is attached it the machine refuses to reboot and hangs on the initial hardware screen not even showing a grub screen. This has always been a native ubuntu machine with no dual boot or any weird grub2 issues previously. Interestingly, I am getting the exact same issue with another HP desktop (Celeron machine) with 9.10 Server 32bit that I' using as a home server. This is obviously a bigger problem because if the server updates or requires a reboot for any reason I can't just leave the drive attached. This drive houses our movie and music collection.
View 9 Replies
View Related
Jul 5, 2011
Have Lian Li Ex 503 External Raid System, using 4x2TB, using Raidmode 10 for good performance [ Just for those who are interested: http://www.lian-li.com/v2/en/product/pr ... ex=115&g=f ]
[Code]...
But using e-sata my transfer rates are very low (from internal drive to external ex503), around 60-70mb/sec
But hdparm tells me:
[Code]...
View 3 Replies
View Related
Aug 13, 2010
Can SATA 3 (SATA III) Hard disk be run on motherboard which only supports SATA II, except sacrificing the speed (throughput)?
View 2 Replies
View Related
Jul 14, 2009
I've never owned an external SATA device, so I'm curious whether these devices are hotpluggable in Fedora. Some computer cases and case inserts have an external SATA connector that plugs into the motherbords built-in SATA connectors and extends the connection so it reaches outside the case. But can you plug and unplug SATA devices just as you do USB devices?
View 8 Replies
View Related
May 29, 2010
Legacy box is SoYo MB PATA only; Slack10.2, 2.6.13 kernel.. All PATA drives I've tried with two IDE to USB cables work fine but was wondering if the cable will work with a SATA drive to the same box, or would I need a SATA to IDE converter, whatever.. Maybe this is a stupid query?
View 4 Replies
View Related
Dec 26, 2010
I have a laptop with dual boot Windowz 7 64 bit and Ubuntu 10.04 LTS 64 bit using windows MBR and EasyBCD. I have no issues booting into either. I also have a 500 GB external HDD which has a NTFS partition for backup data and Linux root and swap partitions at the end. I have GRUB installed on the external HDD MBR and can boot into Ubuntu on the external HDD via bios options. I recently bought a larger external HDD 1TB. Now so far I have made same partitions as old external HDD namely NTFS for bakup followed by Linux root and swap partitions. Linux partitions were cloned using disk cloning while on NTFS partition I only copied data. How do I copy the GRUB from old external HDD to new one so that I can boot into my linux on the new external HDD? BTW the new HDD is Western Digital Passport Essential SE, which also has some factory installed image at the start of drive.
View 6 Replies
View Related
Feb 4, 2011
I am running dual boot Ubuntu and windows 7 but have decided to ditch windows and go permanently with Ubuntu. How do I save my data files (email addresses etc.) to an external hard drive for downloading back on to my laptop when I have reformated it.
View 1 Replies
View Related
Mar 26, 2010
I'm getting a really low speed (2-3 mbps) while transferring data to my USB drive and external hard drive. I've heard this problem's there in Karmic but not in Jaunty but i have Jaunty and yet I'm facing this problem.
View 3 Replies
View Related
Apr 21, 2010
how to transfer large files from my laptop to external hard drive. Problem occurs when I'm sending Blu-ray films (4.4GB) to external, gets to 4GB and then comes up with error. Is there any way of breaking it up and then merging when it reaches the hard drive or is there a way of sending it as one whole file.
View 1 Replies
View Related
May 2, 2010
OpenSUSE 11.2 server, Gigabyte GA-MA790X-UD4P sda for system, 3 ext4 partitions, working fine.sdb promise RAID1 for data, 1 ext4 partition, working fine.sdc is an eSATA docking station for data backup, 1 encrypted ext4 partition -- here lies the problem.
This configuration has been functional for months until I decided to add two more external drives (sdc) to rotate through backups. I had difficulty with encyption on the first new drive and eventually decided to start over. Using the gui Yast Expert Partitioner, I deleted the single partition. That began a real nightmare...
Since deleting the partition, the system detects drives inserted in the docking station, but does not report them (including a different fully functional drive and a brand new unused drive). I have tested all drives on other computers and they function perfectly. I have rebooted the system several times while troubleshooting this issue.
Could not recreate the partition on server (since it does not recognize the drive), so I used Gparted on another computer - it all went without a hitch, formatted ext4. But when I placed the drive in the dock, the drive still was detected but not recognized.
Details:
BIOS lists the eSATA drive
Entering Yast Expert Partitioner, error message follows:
The partitioning on disk /dev/sdc is not readable by the partitioning tool parted, which is used to change the partition table.
You can use the partitions on disk /dev/sdc as they are. You can format them and assign mount points to them, but you cannot add, edit, resize, or remove partitions from that disk with this tool.
Yast partitioner shows drives: sda, sda1, sda2, sda3, sdb, sdb1 sbc is not listed.
# fdisk sdc results in: Unable to open sdc
# dmesg | grep tail reports:
[48442.370779] sd 0:0:0:0: [sdc] Unhandled error code
[48442.370793] sd 0:0:0:0: [sdc] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
code....
So how did partition deletion cause this issue, and how do I correct the problem? It is possible that my difficulties encrypting the first new drive are related (it's not my first time doing it successfully). It seems the problem is in the Kernel or configuration. I have invested many hours in forums and on google - tried dozens of possible fixes. I'm beginning to suspect system corruption or a bug, however all other system functions are working perfectly.
View 5 Replies
View Related
Jul 28, 2009
I have a seagate SATA hard drive that was running a mythtv distro. It had 3 partitions, EXT3, swap, and XFS. I started having I/O errors on boot and saw error messages on both the EXT3 and the XFS partitions. I also heard some clunking sounds on the drive when it was reading, so I thought hell, the drive is dead.
I have since replaced the drive and everything is back up and running on the replacement drive. I thought hell, the seagate drive is toast, but I just want to verify it with some sort of tool. I have the hard drive in a Vantec NexStar external hard drive case (SATA->USB) and found there was a tool called badblocks. Ran badblocks on it, which ran for 24ish hours and found no bad blocks. I also didn't notice any clunking sounds while it was running.
I ran
Code:
badblocks -n -v /dev/sdb
Is badblocks a proper test to run on external hard drives or was I just wasting my time? Is there any way that I can really test it without removing it and connecting it with SATA to the motherboard?
View 7 Replies
View Related
May 17, 2011
How does one split a large linux file and transfer to windows external drive ?
View 2 Replies
View Related
Apr 25, 2010
Is it possible to install Linux on an external SATA drive?I have a system dual booting between OpenSuse and Windows XP. I wanted to see what other distros were like so I tried installing Ubuntu to my external SATA drive. After installing, I got an error from GRUB, and I had to recover my MBR.I tried the same thing with Mandriva, and got the same result. Finally, I tried another install of OpenSuse 11.2. The result was that I get a grub error 21. The only result of my efforts to try other distros is a lot of experience recovering my MBR.
View 9 Replies
View Related
Jun 21, 2010
I installed Ubuntu 10.04, and happened to have an Silicom Images PCXpress card plugged in, and it kindly added the sil_sata module.This is fine for this chip set.I think that my earlier installation of Ubuntu 9.04 used Libata, which does support NCQ and also has good legacy support for the Intel Intel ICH7 chipset I have inside my Sony Vaio SZ notebook. Also, libata also support Silicon Image chipsets as far as I can tell from URL...I wish to remove the Silicom Images SATA modules and replace this with libata and then test the performance between the two device drivers.
View 5 Replies
View Related
Jun 1, 2010
My motherboard supports SATA but I do not know which version: SATA-I or SATA-II. I want to buy a SSD so it would be pointless to buy a fast SSD if my motherboard only suports SATA-I
View 7 Replies
View Related
