Ubuntu Networking :: WiFi Router Connects But No Internet?
Nov 11, 2010
trying to run 10.04 netbook live from a memory stick with a view to installing it on my laptop. However although I can see my wireless router and connect to it I cannot access the internet. I have tried this on my laptop and desktop with the same result. I was however able to download Seamonkey browser using the software manager....this also cannot access the internet. Both of my PC's have no problem when using XP or Linux Mint.
I have also discovered that if I piggyback, using Ubuntu 10.04, on a neighbours open wifi link I can gain access to the internet. My wifi is using WEP protection but as I said I can set the link up to the router, entering the appropriate key code, and have a good signal strength, I just cannot access a google search page.
View 8 Replies
ADVERTISEMENT
Nov 23, 2010
Let me start by saying that I am new to ubuntu, and that I always use forums as a last resort.
I installed ubuntu 10, and immediately after the Wifi card deected my network name, and actually connected to it, but then I opened up firefox and....no internet.
Since then I have been trying to fix this problem, and after some research I found out that my card (PCI Cwp-905) is RT2760 based, and I downloaded the linux RT2760 drivers for it.
The driver folder contained a readme file with commands you should enter to install it, and other setup files.
The problem: every command I typed in didn't work. I tried "make", and then "sudo make", but just got permission denied each time. I am now at a dead end. (Please note that I changed my directory to the folder location before doing this)
Does anyone know what I am doing wrong? If you want I can attach the driver files.
View 3 Replies
View Related
Oct 15, 2010
Since I have 3 Network cards in my Desktop PC I've configured it to act as a Router using GNU/Linux Ubuntu Lucid in combination with Samba so I could share my internet connection. It works on any laptop a connect to it using any of the network cards ports [regardless of the operating system installed on the Laptops], but when I plug that same network cable to any Desktop PC [regardless of the operating System installed] it doesn't even light the LED in the netcards. From the Client PC seems like nothing is plugged in the the netcards.
View 8 Replies
View Related
Aug 6, 2010
I know Windows forward and backward but I am so new to linux it's just wrong. I just installed fedora (like 1hr ago) on and old toshiba laptop with a WiFi PC card. Everything seems to work fine except. My Networks connects to my home Wifi network but it will not connect to internet. When it connects the IP address isn't even close to being in the same range as my other laptops and PCs. Like I said I'm new to linux but I'm wanting to learn. Any fixes for this issue? Which linus book is the best one to read for a beginner? Other then not connecting to internet I have no complaints.
View 14 Replies
View Related
Jan 7, 2011
After forgetting my wifi router password, I had to reset and reconfigure the router. I enabled WEP, and after I typed the password, the computer now recognises it automatically. But I can't connect to the internet no matter how long I wait. (The wired internet connection works fine.) How can I get the wifi to connect to the internet?
View 1 Replies
View Related
Aug 27, 2015
I've been using Debian for about 6-7 months now. I've had a bit of a major networking problem for the past 4 months or so that I've been trying to fix - specifically, it started when I upgraded to Jessie. I can connect to wifi just fine, and sometimes I can even use the internet for brief periods of time (exceedingly rarely). Then... nothing. No network access, period. I can't ping any outside servers, I can't ping other computers on my network, and I can't even ping my router. Pages I try to load just stay "connecting" for all eternity, network printing fails, and so on.
So after four months of searching online (I've read through way more wireless documentation than I care to say), I finally gave up and admitted that maybe I screwed something up during upgrade to Jessie (as a matter of fact, I did, I had to do the upgrade in two increments [somehow] because my root partition was too tiny by mistake) and I did a clean install. Since I had /home on a separate partition, I was able to keep all my user files, but all settings regarding networking were wiped. So after installing firmware-iwlwifi so I can use my wireless card, I tried connecting to wireless! Success! Then I tried connecting to the internet... success! Briefly. The next morning I tried using the internet again, and it failed in exactly the same pattern as before.
I don't know much about what's going on here, but here's what I do have available:
I do have to use firmware-iwlwifi, which I installed by doing apt-get install firmware-iwlwifi. I don't think it's an issue with the wireless card itself (hardware-wise), the laptop dual-boots Windows 7 (that I never use anymore), and Windows 7 is able to connect to the internet just fine. Connecting directly to my router by ethernet cable works fine, I have perfect internet/network access then.
I can confirm that my laptop is receiving an IP address and that it is using ARP correctly to get the MAC address of my router (I confirmed this by doing the arp command, it has the MAC address correct, I checked from another computer with my router's config page) All other computers on my network work perfectly with my router. To confirm the router/its configuration isn't at fault, I did a full factory reset of the router, but to no avail.
Out of curiosity I tried installing Wireshark (using an ethernet cable to download it) to monitor what happens when I try to access a webpage. I'm no expert on networking, but I noticed something out place when I compare a capture from the affected computer to a capture from one operating normally - there are a lot of STP packets showing up. I did some checking around, it looks like STP is involved in bridging and more complex networking setups (involving switches, for example)... but it shouldn't be found on a home network, especially where there's no bridging whatsoever. These STP packets don't show up on packet captures done from any other computer. I've attached a packet capture from the affected computer here, since the forums won't let me attach a .pcapng file.
Here's the output from a few commands I ran during past troubleshooting sessions:
Code: Select allsudo ifconfig
eth0 Link encap:Ethernet HWaddr e0:db:55:b5:fe:06
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:12455 errors:0 dropped:0 overruns:0 frame:0
TX packets:7781 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
[Code] ....
View 5 Replies
View Related
Oct 27, 2010
I have a telephone connection of 1 mega internet modem huawei mt 880 SmartAX my desktop computer is connected via an ADSL PPPoE.I use Ubuntu 10.04 in Spanish and want to know how to connect a WiFi router TP-LINK TL- wr942nd to provide wireless Internet to other 2 PC, a desktop with a plaquet wireles G CNet CWP-854 and 500 series notebook olivetti olibook. The issue is that when I connect the router I can not even go online and do not know how to operate the network, I can not even connect the desktop to my internet provider
View 1 Replies
View Related
May 7, 2010
I can normally connect to most wifi connections, but for some reason I can't connect to my broth's-gf-parent's network. Windows 7 can connect to it just fine, but not Ubuntu. Once in a while I'll go to a cafe, and this will happen there too.hough, like I said I can normally connect to all other wifi networks with no hassle
View 1 Replies
View Related
Mar 4, 2011
i noticed today that the last three places ive tried to use wifi at (a friends house, my cousins house, and my moms office wifi) refuse to connect, even after triple checking all the passwords and trying various security protocols (WEP 40, WEP 128, etc.). strangely, last weekend i was able to connect to a hotel wifi signal with no trouble. even stranger, my ipod touch is able to connect to all these places. at my friends house, we even tried an ethernet cable but ubuntu didnt even know it was there. im a little concerned about this, as i might need to connect to wifi for something really important and ubuntu wont cooperate.
View 2 Replies
View Related
Feb 28, 2011
Another issue I'm having, considerably more serious, is my ability to connect to wifi access points with proxies. The story goes, my school has free wifi, but you have to go through their proxies to access the internet (like at McDonald's or Starbucks, where you must 'log in' and accept their usage terms). I can connect, including DHCP, and when I type in any URI I get the redirect posted to Chromium's address bar, but I simply cannot connect to it. This has happened in Ubuntu and Arch, using at least a couple different network management methods (I usually use WICD but I think I started off with networkd). The strange thing (to me) is that my Android phone works just fine, so although I'm not completely familiar with Android on this level, I don't imagine it's the fault of Linux itself. but I'll only be able to experiment with this once a week, on Saturdays (when I have class --gotta do something entertaining).
View 1 Replies
View Related
Apr 14, 2010
I have sendmail running on my centOS 4.6. My lamp server also runs on it. I want to send mail through php mail function. when i execute php page, which fires the mail function, it takes so much long tim1 say even 1 minute, and at last displays that message sent successfully. Suppose, destination address is [URL].... I did not get any mail there. My server is running in LAN. I checked the status of sendmail, it shows me that it ios running. when i issue "nmap localhost" it shows me that SMTP port 25 is open, but when i issue "nmap myserver" (192.168.1.20 myserver ( written in hostfile)), it does not show that SMTP port is open.
I checked the /var/log/maillog, one person in my previous post advice me to see that. There it shows that message is accepted for delivery...but i do not get any mail in my destination, even not in spam folder. One more confusion is that, in my case my server is in LAN and if I am at all enable to open the SMTP port on it, does i need to open SMTP port on my router (which connects my LAN to internet) also needs to open? I think no, because SMTP is application layer protocol, it will wrap my mail in IP packet, which router just need to forward. am i right?
View 1 Replies
View Related
May 2, 2010
Installed Lucid yesterday. Rebooted and lucid seen my wifi connection but after a few mins drops the connection and will not re-connect. Now, I cannot get it to connect at al even though the WPA password is correct, and rebooting to Win7 shows no problems there.Looks like it's back to go old wicd,
View 9 Replies
View Related
Jul 4, 2011
I've got an Asus EEE 1000HE, and it's worked fine for a long time with the EEEBUNTU distro (a distro based on Jaunty (i think) with a custom kernel). Unfortunately, Eeebuntu is no longer maintained, so I recently did a clean install of Ubuntu 10.04.2. I am now unable to get my wifi to work reliably.
The wifi tries to connect for a while, then pops up the "Wireless Network Authentication Required" window. If I hit "connect" it will try again for a while, then pop up the window. Etc. Note I know that my connection information is OK. I haven't mistyped the password (see below). Also note that the wifi antenna is turned on. For example, iwlist scan is able to find my network.
There is a weird twist though: The netbook is always able to connect through an ethernet cable on eth0 just fine. If I boot the netbook with the ethernet cable plugged in, the wifi instantly connects as well! I can then unplug the ethernet cable (eth0 goes away), but I am still able to use the wifi connection for about 5 minutes before it disconnects, and goes back to trying and failing to connect.
This behavior is 100% replicable--the wifi always works fine (for about 5 minutes) if it boots with the ethernet cable plugged in. Very rarely, the wifi will also connect on boot without the ethernet cable, but that is not replicable.
Other EEE netbooks seem to have issues with multiple wireless drivers, like in this thread. Perhaps something similar is happening here? My card seems to be using rt2860sta as a driver. I tried blacklisting it, to see if another driver was trying to load instead, but that just negated my wifi altogether. (It's unblacklisted again)
My router is a very reliable Linksys WRT54GL with factory firmware which has never been flaky.
I'm at my wit's end. This netbook will be useless without wifi.
Below is the suggested information for a first post:
Here's lspci (note there is nothing listed as "Wireless Brand" to grep out):
Code:
lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03)
[Code]....
View 9 Replies
View Related
Aug 7, 2011
I am spending a week in my grandparents house and I forgot my router. So is it possible to share the Ethernet connection I have with my phone using my laptop's wifi without a router? I think (I have very little knowledge about wireless networks )something like ad hoc network should do the trick? If so how do you set it up?
View 4 Replies
View Related
Feb 6, 2011
I have an old dell desktop with a belkin wifi dongle that connects to the internet right away when i boot in live cd mode but when i try while its installed/installing i get the connecting animation on the wifi, thing, on the top bar.it connects then loses connection and cannot reconnect 5-10 minutes later. this is driving me crazy, i have homework and i just need this thing on the internet already so i dont have to stress my macbook with a minecraft server
View 2 Replies
View Related
Sep 1, 2011
I have a pc which has 2 network cards, 1 wifi and 1 ethernet card.
I'm using wifi card to connect to wifi network (internet) and i'm planing to share this wifi/internet connection via ethernet to wireless router (siemens sx763) so i can have internet on my other devices, e.g. mobile phone, laptop.
View 2 Replies
View Related
May 13, 2009
the only error message I can find comes from "dmesg|tail"all it shows is
"no IPv6 router"any body know what is going on here or where where to look for more clues the next time I get around public wifi Oh the windoze washers and apple polishers don't seem to have any problems at all
View 4 Replies
View Related
Jun 20, 2010
I recently installed Xubuntu 10.04 on my desktop computer that had a USB wireless adapter DLink DWA-140. I didn't have to install any additional drivers to get it to work. I put in the network SSID and the password and was connected immediately. However, when I try starting firefox it doesn't load any sites. Can anyone help me in approaching this problem. I have a DLink DIR-655 router. If I should gather more information to get this problem solved then please let me know and I will do so.
Edit: Now I am unable to connect to the network. When I click the network icon in the taskbar, my home network is not visible while it is visible under another ubuntu computer I'm running.
View 2 Replies
View Related
Jul 17, 2010
I bought a laptop today (Compaq Presario cq62) and loaded Ubuntu 10.04 on it. Everything has been running great, but the Wifi has been acting up. It connects to my router for a few seconds to a minute, and then stops all data transfer (although it still shows that I am connected to the internet). My other computers running Mac work fine. I took my laptop to another place with wifi, and it did the same thing.
The data transfer seems to stop when there is a lot going on. Whenever I try downloading new software, it gets to exactly 5% then stops. If I disconnect the wifi, and reconnect it works again for another minute. I may need to be walked through any terminal codes.
On that note, where would be a great place to read up on using Ubuntu (online book?)
View 1 Replies
View Related
Aug 25, 2010
I installed Ubuntu 10.04 32-bit on an old desktop (1.5ghz Pentium 4, 20GB hard drive, 768MB RAM) a week or two ago, at the same time that I installed Xubuntu 10.04 on an even lower performance IBM tower server. The server functions perfectly and my other (Windows XP) desktop recognized it from the start, as did the Ubuntu desktop. However, I rearranged a few ethernet cables the other day without turning off the desktops and ever since my Ubuntu machine does not recognize my server, even though all of the devices are connected via ethernet cable to a linksys router and it connects to the internet without a problem. I'm a linux newbie - this is my first move away from Windows - and I don't know where to turn. Far more confusing is the fact that, when I boot from a LiveCD, the network is recognized and I can read/manipulate files on my server without a problem. Oh, and I briefly flirted with OpenSUSE KDE (not as noob-friendly as Ubuntu, so I'm back) and encountered the same problem.
Needless to say, booting from the hard drive is preferable to booting from CD every time
View 3 Replies
View Related
Apr 23, 2010
The computer connects wirelessly to a router. The router is connected to the internet and that is working well. (If i use a cable connection to the router, I can reach the internet).
Why wont the wireless connection reach the Internet? It is a strong connection. It worked before wirelessly. I am on 10.04 beta, with the recent updates installed.
View 1 Replies
View Related
Jan 20, 2011
i have a leased line ( speed 2 MB ) which we use to connect to our mail server , oracle ERP etc.. we have a dhcp scope defined as 192.168.100.1-192.168.101.254. with a default gateway as 192.168.100.90 ( which is a cisco router ) we have a pix firewall ( 192.168.100.10 ).. now the gateway passed all the request to firewall..
we have an ADSL of 4 MB speed.. ip is 83.*.*.230 from ISP. i have a proxy server ( squid ) eth0 is connected to ISP (83.*.*.230).. eth1 to LAN ( 192.168.100.79 ) now the problem is when i put default gateway to eth1 ie 192.168.100.90 the squid connects to internet via leased line.. if i leave the default gateway field empty on eth1 , the squid connects to internet via ADSL ( which i want ) but the problem is no one on the lan cant ping the squid server ( no connectivity to internet for the whole LAN ) how can i solve this problem? i want squid to connect to internet with ADSL, but if i put gateway on eth1 ie LAN squid goes through leased line which i dont want to happen.
View 3 Replies
View Related
Oct 21, 2015
When I connect my Debian PC to my WiFi router my PC doesn't get internet if other devices are connected to it .
When i disconnect those devices and connect my Debian PC only then my PC connects to internet but other devices connected to it later do not get inernet connection.
When I connect my Debian PC using LAN Cable to the same router all devices work fine.
View 11 Replies
View Related
Aug 9, 2010
I have one pc on which I have installed slackware and samba (fixed IP, mask 255.255.255.0) I have another PC (also XP) which also has fixed IP running XP, and I can connect that to the slackware server easily My third PC connects to the internet and gets its IP address from the Cisco router(?) that provides the IP and mask on boot up.
I tried changing the IP and Mask on the slackware server to match the internet PC (which uses a mask 255.255.254.0) but the PC mask and IP changed on the internet PC I want the PC that connects to the internet to also be able to connect to the slackware server, but I see no need for the slackware server to also connect to the internet - I will mainly use it as a file server When I worked for another company I think the IT department talked about having 2 network cards in the PC that connects to the internet
View 6 Replies
View Related
Mar 15, 2011
I think I have unique problem. I have a d-link DWL G510 rev c.(Austrailian) WiFi card in my pc which is detected as
Quote:
Network controller [0280]: RaLink RT2561/RT61 rev B 802.11g [1814:0302] in lspci -nn.
iwconfig shows:
Quote:
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bg ESSIDff/any
Mode:Managed Access Point: Not-Associated Tx-Power=6 dBm
Retry long limit:7 RTS thrff Fragment thrff
Power Managementff
ppp0 no wireless extensions.
Now sometimes it detects my wifi router and shows its ssid in nm-applet. but when I try to connect, it tries for 3 or 4 minutes and then fails. for most of time it even does not finds my router.
View 1 Replies
View Related
Jun 17, 2011
I have a Dell Studio XPS15 laptop running 11.04 which works flawlessly with my router (it's a broadcom card btw). Now I'm setting up a new laptop for my Father-in-law which is a Dell Inspiron 15 which has intel Centrino 1000 wireless. I've installed and setup 11.04 on it. Everything runs great except..
Now it can see all the access points around so I assume the wireless card is properly detected and working. But when I try to log into my router and give it my password, it just keeps trying to connect and can't. I've double checked the settings with my own laptop and everything seems the same. why it won't log in? I'm leaving it as a dual boot with Win7 and I know that Win7 will log into the same router with the same password.
View 4 Replies
View Related
May 12, 2010
I've got an Ubuntu box set up as a router and wifi hotspot. I can access the internet and any website using this box. I can connect a laptop to my wifi access point, and connect to both the router box and the internet. I'm writing this message from it. If I access either hsbc Hong Kong internet banking or speedtest.net from my laptop I can't connect. Every other site I've tried is fine. What could be causing this? I don't know where to start. I've set up the firewall rules and routing tables, so I vaguely know what I'm doing... but clearly not enough to debug this issue.
View 3 Replies
View Related
Sep 7, 2010
Is there a way to see the manufacture of wifi router/card remotely like "inSSider" shows, for example ???
View 2 Replies
View Related
Dec 14, 2010
Upgraded broadband service yesterday and now using a combined router and modem (Virgin Media Hub). But I now have no wired or wifi internet connectivity on either of my ubuntu 10.10 systems. I tested it on my work laptop which uses Window and it works fine for wired and wifi.
With 10.10 I no longer have a network icon upper right panel to check, so not sure how to set up wireless. Both machines have static IP addresses and are able to ping each other but there is no internet connection on either.
View 5 Replies
View Related
Apr 2, 2011
am having some problems with getting a pc to use the above software. background is my wife wanted access to mail in her "office". purchased a Tenda wireless router and installed ok (with TPlink pci wireless card on her pc). am using latest version of ubuntu (10.10 x64) on her pc and went to use firefox - timed out, same with evolution and thunderbird. synaptic works fine, opera and google chrome work fine. i'm guessing some sort of tweaking of the router is required but not sure where to start.
View 1 Replies
View Related
