Ubuntu Networking :: No Option For "enable Wireless"?
Feb 27, 2010
My wireless broadband connection was working fine until this morning. I am running UNR 9.04 on an acer aspire one. For some reason i have no option to enable wireless and i don't know what i have done. When i right click all that shows up is "enable networking" but there is no optiont to "enable wireless" anymore. I tried flicking the switch on my netbook to see if that had caused the problem but after doing it and rebooting its still the same.
View 1 Replies
ADVERTISEMENT
Mar 24, 2010
I want to create the following network:
I have a Belkin 54g ADSL Router/Modem connected to ADSL
I connect my laptop (Ubuntu 8.04) wirelessly to this router
I have a Netgear DGN2000 Router/Modem with NO connection to ADSL
I connect my desktop to the Netgear using a wired connection
I want to bridge the two routers and use the internet on the desktop
The Belkin 54g Router setup has options for Wireless Bridge.. I have selected "Enable Wireless Bridging"; as far as I can tell there is no corresponding option in the Netgear DGN2000's settings to act as a wireless bridge. I have changed the ESSID, Security, and Channel all to the same settings and when I turn on the Netgear router the signal strength of the network dramatically increases. I am unsure whether this is the "Bridge" connected... or if the Netgear's signal is just drowning out the Belkin's signal. In any case I cannot use the internet when connected to the network with the Netgear turned on. What do I do?
Or is there some way I can share internet like this:
wireless wired
ADSL--->Belkin54g----------->Laptop-------------->Desktop
View 1 Replies
View Related
May 29, 2010
I am using Ubuntu Lucid Lynx (10.04)I have a wireless card in my PC that I only use very occasionally so I uncheck the Enable Wireless option on the network tool icon to stop the system attempting to connect to my wireless network. That works fine for that session, but the system does not seem to remember this setting and attempts to connect the wireless each time I log in! Is this a feature or a bug? and does anyone know a way of defaulting the wireless option to off
View 1 Replies
View Related
May 6, 2011
I'm running 11.04 on a Compaq presario CQ56. The network dropdown menu doesn't even show "Enable wireless" as an option, which makes me think that the wireless card's driver and/or firmware isn't installed. The network card is a Ralink, but I can't figure out which model/chipset
Here is the relevant output for lspci -vnnk:
02:00.0 Network controller [0280]: Ralink corp. Device [1814:5390]
Subsystem: Hewlett-Packard Company Device [103c:1636]
[code]...
View 4 Replies
View Related
Dec 28, 2010
I am new to linux world, recently installed ubuntu desktop 10.10 on old laptop (fujitsu-siemens amilo). When installed, I noticed that the
1. Enable wireless is grayed out
2. Wireless is disabled
Recently acquired a d-link dwl-g122 ver. C1 USB wireless, didn't want to fiddle with original. I am totally new to linux, this is my first installation.
Tried the gksudo gedit /etc/network/interfaces added these lines: auto wlan1
iface wlan1... IT CHANGES to device not managed, tried /etc/NetworkManager/nm-system-settings.conf:
[main]
plugins=ifupdown,keyfile
[ifupdown]
managed=false
Changing it to true the d link is again disabled?
3. When d link is plugged, ubuntu boots but stuck after login screen?
On Vista, home network I use wpa2 psk protection, essid not broadcasting, hidden.
View 8 Replies
View Related
Apr 18, 2010
Have a question regarding the implementation of TCP keep alives.
If I enable the option of keep-alives on a TCP socket, is there any way that my application can get the response to the keep-alive back from the kernel. Basically, I have a 'select' blocking on a socket on which I have enabled keep-alives. I need to know if select would unblock if a response to a keep-alive sent by the kernel is received on the socket.
View 3 Replies
View Related
Aug 10, 2010
I have a BCM4312 wireless card, using the B43 drivers. It works perfectly fine, except when I bought a new Buffalo Router. I set up the wireless security to be WPA2, but when I use my laptop to connect, the only options are WEP 40/128 key, WEP 128 bit passphrase, LEAP and Dynamic. No WPA of any kind. When I go to edit the wireless settings, I can change the security to WPA2 but when I try to connect again, the wireless manager simply creates another wireless profile with the exact same name with the security WEP. What do I do about this stubborn wireless manager?
View 3 Replies
View Related
May 31, 2011
I own an hp dv9000 laptop, it comes with a Broadcom STA Wireless card... I currently have my laptop connected to the internet through a wired connection, but there is no option at all for wireless.I've already installed the Additional Drivers to install the Broadcom STA Wireless Drivers, and after I reset, there was no difference, no option to choose wireless instead.
View 1 Replies
View Related
Apr 30, 2011
I just upgraded to natty last night, and everything is working fine except for the network manager. I can enable and configure the wireless card via bash, but the network manager widget will not manage the wireless card.
When I first boot up, the "Enable wireless" check box is greyed out. After I enable the card via the terminal, the "Enable wireless" check box becomes ungreyed, but every time I click it, it instantly unchecks itself. I feel like Currly from the Three Stoogies. Check, uncheck, Check, uncheck.. "Slaps face repeatedly."
View 2 Replies
View Related
May 11, 2011
I've had a host of problems since upgrading to 11.04 Natty Narwhal, so let's deal with these 1 at a time.
I've got a Hewlett-Packard Pavilion G60 laptop. Next to the power button is a handy wireless on/off button. This has always worked well with previous editions (9.04,through 10.10). first press toggles the wireless off, second press toggles it on.
Not so in 11.04. The toggle off works great, first time. But, it will not toggle back on. Not after any number of tries, not after restarting, not after booting into other OS's (9.10 and Vista) re-enabling it there and then booting back into Narwhal. to further complicate the issue, this feature bypass the network manager, so toggling the wireless off by the switch leaves me showing no wireless adapter in the network manager. I also restarted, switched from Unity to a Gnome session, but the issue still persists.
As my only network options are wireless, this has become a substantial inconvenience.
----
EDIT: so the network util is actually saying "wireless disabled by hardware switch". Also noticed it I enable it in 9.10, reboot to 11.04 (where I inevitably fail to re-enable it), then reboot into 9.10, it will initially be disabled. The key difference is in 9.10 I have the ability to enable wifi using the hardware button. It seems that 11.04 is remembering that wireless is disabled between boots. Is there a place it might be storing this value? If so, I may be able simply to set the value as enabled, since toggling that silly button isn't working.
-----
EDIT 2:
found this thread:"Wireless disabled by hardware switch" bug? - Natty
seems to be a similar issue. I'll be following how that one develops, too.
View 3 Replies
View Related
Jun 13, 2010
When i click the network manager icon it just says under wireless networks "Wireless network is not enabled" How do i enable it?
View 9 Replies
View Related
Sep 6, 2010
I used the windows executable wubii installation for xubuntu 10.04 I'm not dual booting.My problem is all indications in the user interface are selected "enable networking" "enable wireless" and my wireless switch was on throughout and was connected to the internet during the installation in windows.However
Code:
sudo lshw -C network
Returns
[code]....
View 2 Replies
View Related
Jan 14, 2011
I am a day old in ubuntu-world, and I am having internet issues. Yesterday, after i had installed ubuntu alongside windows 7. To begin with it did not detect wireless (not networks but wireless itself), so i figured it was something to do with the adapter and came to these forums where many things were suggested. none worked. So I restarted the system for good measure and lo and behold it detected wireless networks and connected to the internet almost immediately.
Now, after a day, when i have logged in to ubuntu again, there is no wireless detected. The same problem. When I right click on the network icon in the notification area i see that Enable Networking is checked but "Enable Wireless" is darkened. There is no way to check it.
Can anybody please advise as to what to do next. I am using ubuntu 10.04 LTS (Lucid Lynx I believe).My system config is i7, 512MB ram.
View 1 Replies
View Related
Feb 7, 2011
my computer-toshiba satellite currently running on ubuntu 10.10 i cant connect to wireless except when im at my parents house not to sure why it was working now all of a sudden it stopped while i was using 10.04 figure when i upgraded to 10.10 it would fix it self ..didnt happen so im stumped when i right click on the satelite it the top right of my screen it shows-
-enable networking-(witch is checked)
-enable wireless-(witch willnot allow me to click it)
-enable notifications-(witch is checked)
-connection information- (wont allow)
-edit connections..-
-about-
dont know why it wont allow me to enable the wireless
View 1 Replies
View Related
Jan 29, 2011
My wireless can connect to my router without a problem, but in order to do so (after boot) I must first disable networking in the Notification Area and then re-enable it. I don't mind it too much, but when other people use my computer, it's made painfully obvious to me, that this was never an issue with Windows 7 (as much as I despise MS).
View 9 Replies
View Related
Jul 7, 2010
I have recently installed ubuntu on my laptop. However I cannot enable the wireless on it. The card is registered and drivers are installed. From reading previous forums i can guess that its because its "Hard Blocked"" (assumptions). However the switch for it is in the on postion.
View 2 Replies
View Related
Jul 21, 2010
I have a LG S1 PRO, that to activate the wireless is necessary Fn + F6. How do I enable wireless on command? Since you can not activate in ubuntu with these keys.
View 9 Replies
View Related
Aug 22, 2010
We're on vacation here with free wifi and I brought two laptops. The older of the two laptops running Ubuntu 10.04 and a Broadcom wireless chip suddenly wouldn't work this morning. I checked and it says wireless disabled, however wireless is grayed out when I right click on network manager. I have -no- idea what to do. I've never seen wireless just die like that. I popped open the cover but the wireless card is fine. I re-seated it, booted back up, still no sign of it.
What can I do?
View 3 Replies
View Related
Sep 10, 2010
I updated from Ubuntu 9 to 10 some while ago and can no longer connect to the internet via wireless. The computer is a Medion 96290 with a USB wireless card. Running "lsusb" gives code...
This tells me a driver is installed but it may not be the correct one. I copied this driver from the Windows driver file.
Network Manager shows "Wireless Network" greyed out and "wireless is disabled".
WICD shows net8187b as the installed driver and that the hardware is present.
There is a wireless switch on the keyboard which it was not necessary to use in Ubuntu 9 and is inoperative in Ubuntu 10.
I have searched through and applied many suggestions without success and have posted this problem on a couple of forums, again without success.
View 6 Replies
View Related
Oct 8, 2010
I have been having some problems with my wireless connection. I am having to start my computer 2 times in order for my wireless connection to work. The first time I start up, even after I enable wireless it wont connect. If I reboot immediately and enable wireless it will then connect. I would like to be able to fix this problem since it has become really annoying to me to have to boot my computer 2 times every time I turn it on. BTW Network manager shows auto-connect, however it also shows i month ago as to the last time the connections were used.
View 2 Replies
View Related
Nov 28, 2010
I am newbie at linux and Ubuntu and I have some problems enabling my wireless. I have spent many hours searching for solutions and couldn't find one for me (maybe don't apply it right - I am newbie). I have HP Pavilion dv6, dual boot Win7 and Ubuntu. At Win7 wireless is ok but at Ubuntu I can't enable my wireless adapter, so my laptop can't recognise any wireless network.
View 3 Replies
View Related
Apr 13, 2011
How can I enable wireless injection?
[code]....
View 9 Replies
View Related
May 15, 2011
I am new to linux. I just installed linux on my PC and wanted to configure wireless network connections. I have entered SSID and mode is set to infrastructure. I don't know what is BSSID do I need to enter MAC address (of router?)?I need to connect to internet wireless can you please guide me ?
View 1 Replies
View Related
May 25, 2011
I have an Averatec 3200 laptop with a Intel PRO/Wireless 2200BG card. When I click on Network Connections, it says wireless is disabled. I checked my /var/lib/NetworkManager/NetworkManager.state file, and it said "wireless enabled=false" so I changed it to true.
It just goes back to false on reboot. I also ran rfkill unblock all, but rfkill list still shows that there is a hardware block on. The driver for this wireless card shows that it is installed. I'm not sure what to try next!I just bought this computer used, and freshly installed Ubuntu 10.10 on it, so can't say if it worked in any other distro.
View 3 Replies
View Related
May 26, 2011
i have jolicloud (i think it uses gnome) on my hp mini 110 and my internet has been working fine and everything until for some dumb reason i pushed the wireless on/off button on the front of the computer. normally on windows i would just have to push the button again but its not working with linux. how can i re-enable my wireless?
View 7 Replies
View Related
Jun 20, 2009
I've been experiencing a problem with Fedora in which when I enable Wireless in Fedora, Wireless networking does not work in windows. HOwever, when disabled, it works correctly. Windows claims it is "not able to find any networks to connect to"
EDIT: It seems that when wireless is disabled manually on fedora before shutdown, there are no problems in windows.
View 14 Replies
View Related
Jan 10, 2010
enable WPA encryption on my wireless connection? Wireless networks are detected and listed, so the wireless card is functional in the most basic sense, however, when going to connect to any particular network,I am not given the option of entering a WPA passphrase, only WEP, and as my router is set to use WPA, this is a problem.I am trying to get this going on a fresh Karmic install on a Toshiba A15-S157 notebook.Thus far, I have found this: https://bugs.launchpad.net/ubuntu/+s...ux/+bug/315489 which would seem to relate to my problem.I looked in my logs and saw this entry: Jan 10 16:06:35 cody-laptop firmware.sh[863]: Cannot find firmware file 'agere_sta_fw.bin', and have since found that file, and have downloaded it to my desktop. It seems like this may be the solution, but how to exact it, therein lies my (momentary) problem.
View 2 Replies
View Related
Jan 17, 2010
my wireless just stopped working. the network manager in my panel no longer allows me to enable wireless. the option to enable wireless is there, but it is grayed out and will not let me connect. i reinstalled my wifi driver but it didnt change anything. iwconfig shows that the card is working why is the network manager not?
View 7 Replies
View Related
Jan 22, 2010
I have an Eee PC 701 4G, and some time ago I disabled its wireless NIC in the BIOS to save energy. Now I've come to need it working again, but I can't re-enable it, because it always goes back to being disabled after I boot the eeebuntu installed on the machine. If I just enable it in the BIOS, reboot and go into the BIOS setup again, it's still enabled, but if I let the OS load it'll get disabled. I'm really at a loss here, how do I find out what's wrong? Could it be Ubuntu that does this?
View 3 Replies
View Related
Jan 22, 2010
I am using a Linksys WMP11 V27 pci card that supposed to be talking to a Linksys BEFW11S4 wireless router (802.11B) ...I am able to connect directly to internet (ethernet cable hooked to this wireless router) ... but for indepedence I need to go wireless.I defined the configuration using the Network Connections ... also through ndisgtk .. can't seem to get this two to consolidate.On /var/log syslog I see ....
an 22 14:27:10 ubucomputer NetworkManager: <info> Sleeping...
Jan 22 14:27:10 ubucomputer NetworkManager: <info> (wlan0): now unmanaged
Jan 22 14:27:10 ubucomputer NetworkManager: <info> (wlan0): device state change: 2 -> 1
[code]...
View 1 Replies
View Related
