I am using ubuntu 10.10 and facing problem with cisco VPN connection. VPN connection is getting successful but not able to connect to destination servers.I also tried to add default gw to the the IP which is assigned to my VPN connection but still access to VPN machines not working.
View 1 RepliesI installed Cisco Anyconnect VPN client from the university website, to connect to the VNP. On Windows Vista everything worked fine without problem, while on Kubuntu 10.04 the installation has been OK, but when the client connects, my internet connection drops, so I'm not able to do anything!How should I fix this?I'm currently using an adsl, connecting through pppoeconf.
View 3 Replies View RelatedJust wanted to ask a small question... I've set up a VPN connection to my university and i installed and configured everything ok, cause I can connect without any problems...
Now that I'm connected I want my browser to run through the VPN tunnel created by the connection so i can access certain sites that are else inaccessible, but how do i force my browser (I'm using firefox atm) to do that?
When I'm on MAC of Windows OS, as soon as i connect with a VPN, all connection run through them. Fedora seems to ignore the VPN connection and just continues to use my home-network to connect to the internet.
So the basic question is: how do i use the VPN connection.
Iuse FC10, kernel 2.6.27.21-170.2.56.fc10.i686, fully updated system
I've tried to solve this off and on for a few months, but I just can't.I am a windows engineer but wanted to expand my knowledge to Linux.I deperately have tried to get WIFI working but it just wont connect.I am using Ubuntu 9.04 as 9.10 was a problem with video driver.Initially after build I could see my network on the list, but it was greyed out.After trying a few things on the forum I have now installed a windows driver using ndisgtk which now means I can choose my wireless network from the list.Although it does seem to try with the connecting message and asks for the password, it just doesn't connect on.
Things that may be of use am using WPA/WPA2 hardware of machine is IBM Thinkpad T30 (not one of there better models)I work from home and my work machine is working fine, along with all the other wireless kit in the house, it's just this machine.
I can connect to the internet with wired connection. The switch for the device is on but this command "sudo lshw -C network" has the following results:
#
[sudo] password for nn:
*-network
description: Network controller
product: BCM4312 802.11a/b/g
[Code]....
I use VPNC to connect to a Cisco VPN. I am able to connect, but some issues exist when I use SSH. For example, I login through SSH to a computer in the VPN and I execute ls => it works. If I execute ls -la => connection stalls. I think it stalls every time it is supposed to return more content (top, ls /etc).
If I do scp from my end to server => works. If I do scp from server to my end => connection stalls.
I'm trying to install the Cisco VPN client on Ubuntu 11.04, kernel version 2.6.38-8 generic-pae. I need a step by step process since I am an absolute beginner with Ubuntu and this is my first install on the operating system. I have already tried the network manager but connection always fails. I have also tried the website [URL] but this always fails, seems this was made for earlier versions of Ubuntu and earlier kernel versions.
View 9 Replies View RelatedI just recently installed Ubuntu 9.10 on a dell laptop. My WiFi connection that I've been using on the same computer for years is not working when I log on. However if I run the burnt image cd and choose the option "Use Ubuntu without making any changes to your computer" I am asked if I want install proprietary drivers. If I activate one "Broadcom STA" I can connect to the wireless connection in my house. When I am using the version installed on my laptop it doesn't ask me if I want to install the drivers and it doesn't even find them when I go to hardware drivers under system. So to sum it up I can get connection when I run Ubuntu from the cd but not when I run the Ubuntu on my laptop.
View 3 Replies View RelatedMy lan connection to my router isn't working i have it plugged in the cable is good ( fyi i do have some computer knowledge) So my wireless is working right when i booted up but my lan is not. i have a @#$^ i am afraid to say what it is lol dell with their integrated ethernet card. OS: ubuntu 10.04 everything works fine but the wired connection.
Dlink router with all of the settings made properly. i read somewhere about doing a whole bunch of stuff but i thought that since this was a higher version they would have that problem fixed. i also have aim or msn whichever is more preferred. i hopefully will be notified that someone has responded to this thread.
I'm recent to Ubuntu and have just installed version 10.04 32bits desktop version along side my Windows XP.My wireless internet connection works perfectly under Windows XP as this thread can prove it, but it does not work on Ubuntu.When checking the connections on Ubuntu I see:Wireless Network - disconnected.
View 9 Replies View RelatedRecently installed Ubuntu 10.04 on HP Pavillion ze5400.Wireless card is bcm94306MP. Wireless connection shows as disconnected. I am troubleshooting using the Ubuntu documentation on solving wifi problems. Ran ishw and it appears I do not have a driver properly installed. Obtained what I believe is the driver: bcmwl5.inf and bcmwl5.sys. Installed bcmwl5.inf using ndisgtk. I know its there as I can see it in System>admin>windows wireless drivers. However lshw still does not show it under configuration. I understand I must put the sys file in the same folder as where this inf file got installed. I assume all I do is copy and paste it into that folder. Is this correct? Next I need to find that folder. I tried the command find /home -name bcmwl5.inf and it did not show up. Can someone educate me just how to do this, that is find the folder and insert the sys file?
After I pass this hurdle then I will tackle trying to configure the card.
I have a wired problem in Ubuntu 10.10, My Ubuntu can connect with Wireless network, however it cannot connect to Wired Connection. I installed dual System, one is Ubuntu 10.10, the other one is Win7. Under Win7, I can both connect to the Internet in Wired or Wireless mode.
The more wired phenomenon is: When I plug in the cable, I can see the icon connected in my network manager. But I cannot visit any URLs. By checking the "ifconfig -a", I can see the IP addr was assigned to my eth0.
installed Ubuntu 10.04 on my Dell 1564. My cabled netwo connection is not working.buntu has been dual booted with Windows 7. Internet connection on Windows is working. I have an ADSL modem connected to my laptop via the cable.I have given the details of commands asked to be execute(viewed various posts).
isr@ISR:~$ lspci
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 12)
00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 12)
[code]...
Running a wired connection through a Linksys router that suddenly stopped working today.I thought this was a ipv6 issue sinced I enabled some of those settings to share a connection with my PS3.I have since disabled IPv6 in Firefox and through the grub. The RealTek adapter will not even show a connection through the network manager when connected.The onboard adapter will show a connection, give me a ip address and MAC but still will not load the internet. I've tried uninstalling and reinstalling both adapters through the network connections, as well as reinstalling Firefox to no avail.I've also tried using Open DNS servers.I cannot ping through the network tools either. Hard for me to paste a ifconfig since I'm on my laptop.I'm running Ubuntu 10.10 (not dual booting).I did some updates this morning but it worked fine for a little while after that, until I tried to connect to my PS3.
View 3 Replies View RelatedI have an OpenVPN setup at work, and windows clients are able to connect fine. On my dual-boot system (Windows XP 64-bit and Ubuntu 10.10 64-bit) I'm able to connect on Windows but not Ubuntu. I use the same files for each. The network manager wasn't working, so I'm doing it via the command line right now:
Below is the output (sanitized)
Code:
Does this mean it's connected? If so, I'm not able to ping anything on the remote network, not even the OpenVPN server.
When I start my Ubuntu machine, it says "eth0 connection established". But i could not able to ping to other machines available in LAN & also to Internet.
View 1 Replies View RelatedI recently installed 11.04 on my PC (was running 9.04), and beforehand "tried it out" and networking was fine. I could access the internet no problem.I then ran the install, and fully formatted my HDD (i have 1 HDD for the OS and another for storage)It crashed halfway thorough, so no problem, i just re-formatted the hardrive and installed.However, It didnt connect to the internet, I literally tried every single forum looking for the solution, including editing the Network interface file.After a bit of diggingfound my user privileges did not allow me to connect to ethernet, and randomly use audio devices.SO, no problem I checked the boxes, but it still wont connect to the ethernet now, and it was fine before, tried re-installing twice with full format, but still doesnt work.
View 9 Replies View RelatedPut all Cisco drivers and firmware for wireless in a new ubuntu 10.04. I love ubuntu and I have a big problem with a mini pci wireless Cisco Airo MPI 350...
View 9 Replies View RelatedWhen I try to connect to my company's VPN using the Cisco VPN client, I get a kernel panic. Please don't suggest I should Cisco's client, it only works with Kernels older than 2.6.24 (I have 2.6.35).
So I use vpnc. The error message is:
Quote:
$ sudo vpnc
[sudo] password for phirt:
Enter password for user@group@fubar.net:
received notice of type (ISAKMP_N_NO_PROPOSAL_CHOSEN)(14), giving up
vpnc: quick mode response rejected: (ISAKMP_N_INVALID_MESSAGE_ID)(9)
this means the concentrator did not like what we had to offer.
Possible reasons are:
[Code]...
When I connect to my company's VPN (it's a Cisco), it connects just fine and displays the broadcast message, but once connected I can't ping anything or ssh anywhere. Not on the private network, not on the Internet [URL], nothing. I can still browse the web without difficulties when connected to the VPN, but no ssh or ping. With ping, it properly resolves the host name, but I get 100% packet loss.
Once I disconnect from the VPN, a ping of [URL] works exactly as expected.
I don't have any firewalls set up on this host that I'm aware of (unless something is installed and configured by default).
I'm using Ubuntu 10.10, amd64 build.
I can't install/configure this router. I have my PC connected to it via ethernet cable, and Ubuntu sees the connection, but I can't connect to the internet and I can't access 192.168.1.1. I've searched the forum, and I know there are a lot of threads on this, but neither were helpful and since the CD has only win drivers, I couldn't install anything.
I can access the internet through a phone using WiFi though, so theoretically everything is working, I just can't use it with the PC.
I have just installed Ubuntu 11.04 and the Cisco VPN client with :
apt-get install network-manager-vpnc
I have imported the PCF provided by my employer into the GUI. The group password also seems ok, when I login to the VPN server, I am provided with the "VPN Login message". (On Windoze, I get an Ok/Cancel popup with the same message). In Ubuntu, I don't get to click "Ok" but it looks like I'm connected properly. The /var/log/syslog file contains numerous static routes added, 30 or so. After the Login Message, I see the couple of line:
Jul 8 12:40:51 ubuntu02 vpnc[1613]: can't open pidfile /var/run/vpnc/pid for writing
Jul 8 12:40:52 ubuntu02 NetworkManager[630]: <info> VPN connection 'VPN to my network' (IP Config Get) complete.
I get an IP from the external network correctly as well:
tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:172.16.10.170 P-t-P:172.16.10.170 Mask:255.255.255.0
However, I cannot ping any of the machine on the remote network. None of the network services seems to be accessible. Why the machines on the VPN are not accessible?
I'm using Ubuntu 11.04. I'm trying to get a Cisco Valet Connector AM10 to work. It's one of those ZeroCD USB devices that is both storage and modem. Using this link:
[URL]
I filled out usb_modeswitch like this:
Code:
# Configuration for the usb_modeswitch package, a mode switching tool for
# USB devices providing multiple states or modes
#
[code]....
I recently installed ubuntu on my laptop and the wifi is horrible. The connection was very slow and dropped every 5 minutes or so. I have tried enabling the proprietary madwifi drivers - however then it wouldn't connect at all.
View 1 Replies View RelatedI have a cisco linksys wireless adapter (WUSB600n) which, most of the time, great when booting up. But mostly after some time (1min- 1hr.) it disconnects. When checking the status I can see some of the networks around me, including mine. But selecting it doesn't do anything. I searched the forums and tried:
sudo dhclient
and
sudo /etc/init.d/networking restart
But still no connection; the only thing that helps is rebooting.
I have a strange problem with my mobile broadband connection. I hope I am not the only one (so it will be fixed), but since I haven't found any others having the same problem yet, I am not so confident.I started using mobile broadband, via a HUAWEI E1762 HSPA USB stick since Jaunty. I've had the same problem in jaunty as I do now in Karmic. Although in Karmic, i've had additional problems (that problem i've found listed as a known bug).The problem is that when I get my mobile broadband to connect, it is sometimes, somehow, not fully connected. Symptoms are as follows:
1. panel icon shows connected and good strength (good)
2. skype connects, and I can chat and voip (good)
3. ping does not work (bad)
[code]...
After installing UNR onto my dell mini 9 and downloading the correct drivers to enable wireless internet (using this site: [URL]), I decided to load ubuntu onto my brothers netbook. After the installation completed, I went to do complete the steps listed in the above article, however I was unable to connect to the internet using an ethernet wire.
View 9 Replies View RelatedI recently installed KDE in my ubuntu machine. I would like to try it out for a few weeks at least, but networking is not working at all.
I somehow managed to find the network settings and it shows no connections, wired or wireless. When I log out and log back in with gnome, my wireless gets connected automatically.
I am using Ubuntu 10.04 LTS - Lucid Lynx(great interface!). But I am experiencing a very weird problem. The wireless internet works just fine at my apartment. But when I am in my school, it just stops working at all. It didn't use to be like that. It used to work in school too few weeks before. But I don't know what happened all of a sudden. I have checked with my school system administrator to know if there has been any change with the network. He said the network has always been the same.
View 3 Replies View RelatedI'm using a WUSB54GC network adapter to connect to my home wireless network. My network was not visible, so I added it and it shows connected, but when I launch the browser, I can't get a connection. I'm using Ubuntu 10.4. All other computers on the network connect fine and I disabled my firewall to see if that made a difference.
View 1 Replies View Related