Ubuntu :: Kernel ACPI Bugs With Dell Optiplex 320
Dec 21, 2010
I'm trying to get WOL (Wake On Lan -suspend and hibernate don't work either) working in Ubuntu 10.10 amd64 on the above computer for a family member but seem to not be getting anywhere! WOL is enabled correctly I verified that after shutting down in windows XP that the computer came on with WOL. I have tried the following:
Enable wol
Code:
ethtool -s eth0 wol g
The computer shuts-down but won't wake up by WOL packet. Make sure the Ethernet (MAC0) can wake up PC
Code:
echo "MAC0" > /proc/acpi/wakeup
The computer shuts-down but won't wake up by WOL packet
Kernel parameters:
Code:
acpi=off
Code:
apm=power_off acpi=off
Code:
acpi=nopci
With all of the above, the computer doesn't not power down after shut down. The power button light is still on and has to be pressed to turn it off. Here is the strange thing: WOL works after manually tuning it off! I tried inserting apm module but it is not available.
View 3 Replies
ADVERTISEMENT
Sep 17, 2010
I have read all of the articles I could find on the problems. I am using the lilo bootloader as grub doesn't work. I have also added pci=nomsi to my lilo.conf and ran lilo -v. I can get the system to boot with kernel-2.6.18-8.el5. However I can't get the system to boot with kernel-2.6.18-194.11.3.el5.i686.rpm. When I boot with kernel-2.6.18-194.11.3.el5.i686 the system hangs after it prints bios data check successful. I tried adding suppress-boot-time-BIOS-data to my lilo.conf (I ran lilo -v after the change) and the system still hangs. The Optiplex 320 is running bios 1.1.12
Why won't newer kernels work? Is there a way to get more information to print before the hang to aid in debugging?
View 16 Replies
View Related
Nov 7, 2010
I have learned something that I wanted to share with everyone. I don't know if this has been posted before. I was using a Dell optiplex 270 with a penium 4 processor 3 ghz computer 4g RAM dual processor. I tried to put the new Ubuntu on it because everyone was raving about it. Everytime I put the 10.04 on it, it slowed down and became very sluggish. I then had to reformat it back to 9.10.
I had an extra computer here that I was not using. It was also a Dell but it was an Inspiron 530 with an Intel Celeron CPU 2 ghz and 2g RAM. Well, to my suprise, it works GREAT with Ubuntu 10.04. I have not had one issue with it since I installed the new Ubuntu. In my opinion, it is a processor issue. I don't think that Ubuntu 10.04 works with a Penium 4 processor. It does work GREAT with a Celeron CPU processor.
It has been my understanding that Ubuntu (Linux) was made and has been made for older and new computers. It does seem that the new releases have been made only for the newer computers. Has anyone ever had these types of issues or come to these types of conclusions?
View 9 Replies
View Related
Feb 21, 2011
I installed Ubuntu 10.10 32-bit on a Dell Optiplex GX240, it has an ATI Rage 128 Pro Ultra TF (from lspci output) and all the graphics run very slow (I'm assuming because OpenGL and hardware acceleration are disabled). I Googled the issue and found several solutions but non of them worked. I tried installing the ATI Catalyst driver but it doesn't recognize the graphics card. I also tried to install the fglrx drivers but when I run fglrxinfo I get a segmentation fault. So the X server is running with the open source (r128) drivers and it's really slow.
View 2 Replies
View Related
Jul 12, 2011
I try install debian 6 on my dell gx 270, but on some step of instalation I have error. I try other computer, also dell gx 270 but same problem. I try change cd rom, hard disc, ram .... but problem is still here. Is some chipset or something from dell is problem? I try install firmware-6.0.1a-i386-netinst.iso and debian-6.0.1a-i386-kde-CD-1.iso
View 3 Replies
View Related
Feb 7, 2009
I have a Fedora 6 in DELL Optiplex 755. When I installed Fedora 8, I got the following error message:
"An unhandled exception has occurred. This is most likely a bug. Please
save a copy of the detailed exception and file a bug report against
anaconda at http://bugzilla.redhat.com"
This error message is from action of screen: "Installation requires
partitioning of your hard drive. By default, a partitioning layout is
chosen which is reasonable for most users. You can either choose to use
this or create your own."
I chose: "Remove Linux partitions on selected drives and create default
layout" or
I chose other options, but I still got same error message.
Then I switched to a new HHD, but I still got the same error message.
View 2 Replies
View Related
Jan 22, 2010
i have installed windows as well as linux on my system(dell optiplex 760).i m trying to install lan card drivers but the following error occur."Error resolving dependencies "unable to resolve the dependencies for some packages selected for instalation.
View 1 Replies
View Related
May 11, 2010
I recently switched my computer over to Fedora 12 from Win7. When I booted off the Live CD everything worked great, but after I installed and ran a yum update, I have no sound! The volume is not muted in any of the places I could find to look. I had the same problem in Ubuntu 10.04, which is why I decided to switch back to Fedora thinking I may not have the issue there ... but alas I was wrong. Here is some system info:
amixer output:
Simple mixer control 'Master',0
Capabilities: pvolume pswitch pswitch-joined penum
Playback channels: Front Left - Front Right
Limits: Playback 0 - 65536
Mono:
Front Left: Playback 57016 [87%] [on]
Front Right: Playback 57016 [87%] [on]
Simple mixer control 'Capture',0
Capabilities: cvolume cswitch cswitch-joined penum
Capture channels: Front Left - Front Right
Limits: Capture 0 - 65536
Front Left: Capture 48777 [74%] [on]
Front Right: Capture 48777 [74%] [on]
lspci output (relevant part)
00:1b.0 Audio device: Intel Corporation Ibex Peak High Definition Audio (rev 05)
dmseg | grep hda output
hda_codec: ALC269: BIOS auto-probing.
ALSA sound/pci/hda/hda_codec.c:3881: autoconfig: line_outs=1 (0x1b/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3885: speaker_outs=1 (0x14/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3889: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
ALSA sound/pci/hda/hda_codec.c:3890: mono: mono_out=0x0
ALSA sound/pci/hda/hda_codec.c:3901: inputs: mic=0x19, fmic=0x18, line=0x0, fline=0x0, cd=0x0, aux=0x0
ALSA sound/pci/hda/patch_realtek.c:1288: realtek: No valid SSID, checking pincfg 0x411111f0 for NID 0x1d
ALSA sound/pci/hda/patch_realtek.c:1368: realtek: Enable default setup for auto mode as fallback
View 4 Replies
View Related
Apr 2, 2010
I have a brand new OptiPlex 780 from Dell, I downloaded CentoOS x86_64 from [URL]. The installer runs the graphics mode OK, when I reboot into normal, the graphics doesn't work.
The last messages I see are:
Red Hat nash version 5.1.19.6 starting
starting clock,
starting UDev
then the display goes away, the montior says "Not Support" The monitor is 1 day old and supports VGA to 1680x1050.
I try pressing "I" (and/or "i") when Red Hat first starts, but the interactive menu doesn't show.
I have two idenical machines, the other is running XP (the CentOS was also before I loaded CentOS), WinXP is allowing screen resolutions of
- 800 x 600 @ 60Hz, 72Hz, or 75Hz
- 1024 x 768 @ 60Hz, 70Hz, or 75Hz
- 1280 x 1024 @ 60Hz or 75Hz
- 1680 x 1050 @ 60Hz
...all working on the same monitor.
During Bios boot, the monitor shows 600x800 @ 60Hz, during the text-only start of CentOS, it shows 720x400 70Hz. After CentOS boot shows starting udev, the montior breifly shows 720x400 70Hz, then "Not Support".
So....
Why isn't CentOS using the same graphics mode it used during installation (that worked fine)
View 1 Replies
View Related
May 6, 2010
I'm trying to run CentOS 5.4 (downloaded yesterday - CentOS-5.4-i386-bin-DVD.iso). Install process run well Pick default options on install. On partitioning part I've pick "Remove all partitions on selected drives and create default layout"
It get stusk after grub loading at : root (hd0,0) Filesystem type is ext2fs, partition type 0x83 Kernel /vmlinuz-2.6.18-164.el5 ro root=/dev/VolGroup00/logVol00 rhgb quiet [linux-bzImage, setup=0x1e00, size=0x1b3634] stops there, and not load the operating system
System : Dell Optiplex 320
PROC : Interl pentium D 3.00 Ghz
Mem : 2 GO DDR2 Windows XP SP3 was installed previously on this machine.
View 1 Replies
View Related
Jan 28, 2010
Where can I find the device drivers so I can install RHLE v5.x on a Dell Optiplex 755?
View 5 Replies
View Related
Sep 8, 2010
I've just installed 12 new Dell Optiplex 960 computers with Dell 2009W monitors. They are identical hardware and OS installs. Some of them are exhibiting a weird problem with their screens: They boot up and run just fine, but then the monitor goes black for 2 or 3 seconds, and comes back, with the small DVI icon popping up in the upper left corner to show which video connection is active. This repeats at random intervals continously; sometimes just a few seconds between, and sometimes many minutes.
The problem initially happened on just one machine so I had Dell swap the motherboard thinking it was a hardware issue. That did not fix it. Soon after that, I got reports from several users of the same problem on other of the new machines.
I've done a very basic install of CentOS 5.5, skipping all of my local configuration management stuff, and it still happens. Then I installed Ubuntu 10.04 and over the last few hours the machine has been rock solid. No video issues at all.
Here is the output of lspci:
View 10 Replies
View Related
May 5, 2010
I'm a Dell Optiplex 380 MT Workstation user which have a Intel HDA Integrated sound controller. I was using Ubuntu 9.10 32 Bits Karmic, and all works fine, but, two days ago I did a fresh install to Ubuntu 10.4 LTS 32 Bits Lucid. In Ubuntu 9.10 I didn't do nothing to make work all features of my workstation, but, in 10.4 LTS the sound don't work. The hardware appear in "Speaker Icon" and in the alsamixer menu, but nothing works. It's happens in the Live CD, Installation in Hard Disc, 32 Bits Version and 64 Bits version.
Here is the output of the command, in Ubuntu 9.10 & Ubuntu 10.4. The only difference that I see is the follow in lspci (bold text):
lspci
Ubuntu 9.10: 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
Ubuntu 10.4: 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01)
At both version this is the which use (same output):
cat /proc/asound/card0/codec#0
Codec: Realtek ALC269
I've installed linux-backports-modules-alsa-2.6.32-21-generic-pae, reboot system and nothing happens.
lsmod | grep snd
Ubuntu 9.10 .....
View 9 Replies
View Related
Aug 16, 2010
My next door neighbor has a dell Optiplex gx270 and wanted Ubuntu installing.
Hardware:
1gb RAM
P4 2.4
Intel 82865g Onboard Graphics.
40gb HDD
I tried the live cd and it froze on bootup, so I thought it might not be enough ram as the case sticker said 512mb ram. So I booted the minimum install cd and installed ubuntu desktop on it and then rebooted, when it boots i get grub and then screen will either do 1 of 2 things.
1. I get another flashing cursor in top left corner and then cursor stops flashing and then nothing happens at all.
2. Then screen will go black and nothing will show at all.
I have tried updating the BIOS, adding i915.modeset=0 to grub, didn't work either. Also couldn't find the xorg.conf under /etc/X11 to change driver to vesa. After several reboots atleast 30 since the check disk think showed and then it froze again. it booted correctly so I tried the latest intel driver from xorg edgers ppa. Rebooted and still the same thing happens. tried 2 different installs now and get same results. I have had to put winxp on it so he can atleast use it, but this will run out in 30 days unless he decides to buy it.
View 6 Replies
View Related
Oct 5, 2010
I have just bought a Dell Optiplex 960 with a NVIDIA Quadro NVS 450. Everything works out of the box with the 10.04.1 Live CD. It suggests to install and activate NVIDIA proprietary drivers, but you need to restart the machine afterwards.The problem is that, after that, all what you get is a blank screen, with not even a cursor.The same happens when you install Lucid: blank screen with no cursor.
Ctrl+F1 does not show anything, but Ctrl+Alt+Prnt Scrn+REISUB works and the PC is reset.In the var directory the logs show that the NVIDIA module is not loaded.
View 2 Replies
View Related
Jun 4, 2011
I'm currently stuck at the "lubuntu - Install lubuntu" screen on a Dell Optiplex GX150 (specs; Pentium III 1 GHz, 512 mb RAM, 20 GB HDD). I can hear the CD spinning up but nothing happens. Looking at the specs, the PC should be able to run lubuntu, right? Could somebody point me in the right direction? I've verified both the ISO and the CD checksum, both check out, so there should be no issue with the install media
View 1 Replies
View Related
Mar 2, 2010
After installing a Dell Optilex 280 desktop with Centos 5.4, I configured sendamil, squid and all the extras I needed for a proxy and email server. All was fine until I switched the machine off. I had changed the resolution before and all was working fine. Now I have lost my gui , the system starts O.K but goes blank after "starting udev". I can use webmin to administer the server from a nother desktop/laptop but the monitor is totally blank. I tried most configurations on the /etc/X11/xorg.conf file even tried to create a new one using X -configure but still nothing changed. I cant afford to reinstall because of the time it takes to update the box, our broadband connections are so expensive this end of the world (Zimbabwe) and not so efficient. I have looked at the logs and tried to google but the solutions wont work for me? I suspect there could be an issue with the intel graphics adapter?
View 3 Replies
View Related
Sep 10, 2011
I no expert and this was a bit of mucking around. Installed Version 5 dot something on a desktop (DELL OptiPLex) with a couple of extra HDDs, for a server to play with (samba to Windows). I used the drives as a single logical drive via LVM.
We had a power cut, now it doesn't work. In fact it's been hanging around for a couple of years and before I dump it I wonder if there is any chance of getting some of the wife's letters, pictures, etc that I promised I try and get off.
The /boot partition seems to be there and I've attached a photo of what happens at boot, and I admit....I haven't a clue what it all means. Also I did not think ahead and did not create a recovery disk. I know, I know heap damnation on me for being so reckless, but any chance I can get myself back in the wife's good books?
View 7 Replies
View Related
Apr 8, 2011
I am trying to install Ubuntu on my Dell Optiplex GX60 and am getting a black screen with white letters of errors and other stuff.
For instance.bad_area_nosemaphore+0x90/0x130
do_page_fault+0x378/0x440
error_code+0x73/0x78
etc.
View 1 Replies
View Related
Nov 18, 2009
When attempting to install FC12 x86_64 on a Dell Optiplex 760, my USB devices stop working after initial boot. I see anaconda, but am unable to change anything since my keyboard, mouse and any other USB devices are not powering up after kernel boot.
View 13 Replies
View Related
May 30, 2010
I have laptop Dell Vostro V13:
[code]...
I'll provide this info, if this can help to improve Debian on this hardware. I always see this ACPI errors in dmesg:
[ 0.084001] ACPI Error: ACPI path has too many parent prefixes (^) - reached beyond root node (20090903/nsaccess-429)
[ 0.084001] ACPI Error (psargs-0359): [^LPCB.EC0_.LANW] Namespace lookup failure, AE_NOT_FOUND
[ 0.084001] ACPI Error (psparse-0537): Method parse/execution failed [] (Node c14edd50), AE_NOT_FOUND
i also attached full dmesg, and some outputs. Hope, that this can be useful for core developers.
View 1 Replies
View Related
Oct 9, 2010
this is my x-th attempt to compile the kernel on debian lenny. after solving the damn LGUEST issue, now i got an --append-to-version=-foobar issue?! damn... much time wasted, again. after make menuconfig and make-kpkg clean i start compiling with
Code:
fakeroot make-kpkg --initrd --append-to-version=-cpupmopt kernel_image kernel_headers
error log:
Code:
< ... snip ...>
H16TOFW firmware/edgeport/down.fw
[Code]...
EDIT: since this is debian specific and i used make -j5 etc. for # of jobs in other distros, is there an option on make-kpkg for that? && any chance for resuming?
View 2 Replies
View Related
Jun 30, 2011
I find that the FC 15 Xfce spin will save the user's current session except that it doesn't save what is being done with the Lyx editor. Under FC 15 Gnome 3, I found that after I added the minimize-maximize-close buttons to the top of windows, that some of the windows in Lyx (such as the one that appears for View as DVIPS) didn't respond to those buttons. (I don't remember whether Gnome 3 saved the Lyx session and I've gotten rid of Gnome 3 now.)
View 1 Replies
View Related
Jul 8, 2011
I use Slackware 13.37 32-bit version on ThinkPad X60s. I compiled two Window Maker dockable applications monitoring the processor temperature, fan speed, and battery status: wmpower (see: [URL]) and wmlenovo (see: [URL]). Both these applications refuse to work.
wmpower displays the messages:
Code:
CPU frequency scaling available
No power management subsystem detected
No power management support...
wmlenovo displays the message:
Code:
No ACPI support in kernel
Did I missed something obvious during the configuration of the system and ACPI doesn't work for me or there's some more serious problem with my system?
View 4 Replies
View Related
Feb 11, 2011
I just built some machines with the Intel 82574L gigabit ethernet chip, loaded Fedora 14, and discovered a problem with the e1000e driver dying after a few minutes. A little time spent perusing the web told me that the same driver had problems in Fedora 12 and Fedora 13 as well. Congrats to Fedora for the hat trick.As of kernel 2.6.35.10-74.fc14.x86_64, e1000e driver 1.0.2-k4 still had bugs.[URL]
View 6 Replies
View Related
Jan 14, 2010
Having trouble rebooting a system. Have a Ubuntu 9.10 (2.6.31-16 generic-pae) build on a VMWare installation. The system was fine until I rebooted after an update. Now I get the above message and the system halts loading. Have tried to Grub acpi=off and acpi=force to no avail.
View 1 Replies
View Related
Feb 12, 2011
I have a custom built 2.6.37 kernel where I have most of my devices compiled into the kernel. The only modules are related to nouveau (in case I want to go back to proprietary nvidia) and sound drivers. Everything seems to be running fine. However, in /proc/acpi, I'm missing a number of entries, such as thermal_zone/, dsdt, etc. I do have ac_adapter/, battery/, button/, event, processor/ and wakeup. I've gone through what I think is a very detailed review of my kernel config, and I can't find where I've missed something ACPI related. Here is my kernel config with the ACPI section.
Code:
# Power management and ACPI options
CONFIG_ARCH_HIBERNATION_HEADER=y
CONFIG_PM=y
# CONFIG_PM_DEBUG is not set
CONFIG_PM_SLEEP_SMP=y
CONFIG_PM_SLEEP=y
CONFIG_SUSPEND_NVS=y
CONFIG_SUSPEND=y
CONFIG_SUSPEND_FREEZER=y
CONFIG_HIBERNATION=y .....
View 12 Replies
View Related
May 29, 2011
When I run OpenSUSE from the Live CD using normal settings, booting stops with a blank screen a moment after the kernel is loaded. When running it with ACPI disabled, it works, but direct rendering is disabled, even though it detects my video card (Mobility Radeon HD 5650) correctly Here's the Xorg.0.log file: my xorg log - [URL]
View 3 Replies
View Related
Jan 7, 2010
I just installed Fedora 12. When I boot, only the following three lines are printed: pnp 00:09: can't evaluate _CRS: 12298 ACPI: Expecting a [Reference] package element, found type 0 Kernel Panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) I first installed Fedora using a RAID 1 setup that mirrored each partition, so I thought the problem was coming from GRUB and confusion from what to boot off of. However, I reinstalled Fedora using a simple single drive setup (left the second drive without any partition), and the same error was returned. Is this an ACPI issue with this particular motherboard/BIOS? Any ideas for how I can fix this?
View 1 Replies
View Related
Jun 5, 2010
this isn't so much slackware specific as it is general linux related, but using the default huge slackware kernel included with 13.1, acpi reports cpu temps of about 55 celsius i always like to run my own kernels though, and using the latest stable kernel, i have compiled one using what i believe is necessary for my hardware, and everything works as expected except that acpi reports my cpu temp as 80 celsius at idle, causing my fan to be running constantly
so without simply using the generic config included with slack in the newer kernel, what do you think might be causing the thermal issues? i used diff on the two configs and the output is over 5,000 lines, so thats not a huge help, and im really not even sure what to be looking for the cpu is an intel i7 720qm, so if anyone might know any specific settings for that processor type needed for acpi to interface with it properly that would be much obliged here is my config for potential review: [URL] also, if i disable acpi entirely, the fan operates as normal but i cannot get readings obviously
View 1 Replies
View Related
