Ubuntu Installation :: Blocking - SATA Disks Not Recognized
Sep 2, 2010I try to install ubuntu 10.04.1 on my pc but i fails at the very beginning because of HDD problem. I get messages such as :
[Code].....
ADVERTISEMENT
Debian Hardware :: Servers Which Contain SATA Disks And SAS Disks?
Feb 25, 2010I have servers which contain SATA disks and SAS disks. I was testing the speed of writing on these servers and I recognized that SAS 10.000 disks much more slowly than the SATA 7200. What do you think about this slowness? What are the reasons of this slowness?
I am giving the below rates (values) which I took from my test (from my comparisons between SAS 10.000 and SATA 7200);
dd if=/dev/zero of=bigfile.txt bs=1024 count=1000000 when this comment was run in SAS disk server, I took this output(10.000 rpm)
(a new server,2 CPU 8 core and 8 gb ram)
1000000+0 records in
1000000+0 records out
1024000000 bytes (1.0 GB) copied, 12.9662 s, 79.0 MB/s (I have not used this server yet) (hw raid1)
[Code].....
Ubuntu Installation :: Automount Sata Disks On Start?
Jan 17, 2010i installed latest ubuntu server 9.10 on my mini itx board which i have 1 4gb IDE disk and 4x2TB sata disks attached no i want those disks to automount on startup is there a way without modifiying fstab? the thing is, i want to expand the storage over time (next hard disks in a few months) and maybe a second mainboard in a year so i need a simple way to mount everything without being to mainboard specific like doing fstab entries
View 2 Replies View RelatedUbuntu Installation :: USB Detected Beofre The Sata Disks Are?
Oct 19, 2010used to run ARC linux and Windows 7 on my computer and i am now trying to install Ubuntu 10.10 X86_64When i used the live disc of Ubuntu 10.04 and load the installer it finds my four harddrive they way it should... sda,sdb,sdc,and sdd...When i however try the same with ubuntu 10.10 it displays my usb cardreaders drives first and then my hardrives as sde sdf sdg and sdh.I tried installing ubuntu with the reader unplugged and then reconnecting it after installation...But when i then boot with the reader attached it says it cannot mount drives sda,sdb,sdc and sdd becuase they are not ready.I think it is again detecting the usb cardreader before the sata controller ...Is there a way for me to alter the boot detection order so it will find my harddrives first and then the usb cardreaders ports ?
View 1 Replies View RelatedUbuntu Servers :: Mount 4 Internal Sata Disks Using Hal On Installation?
Jan 20, 2010i currently try to mount 4 internal sata disks using hal on a server installation?
i did
apt-get install hal and copied a .fdi script to /usr/share/hal/fdi/policy/10osvendor/30-storage-all.fdi
as far is i understand now i need a hal/dbus client
gnome-volumen-manager seems to be one
apt-get install gnome-volume-manager
now im stuck there is no such executable like gnome-volumen-manager thus, how does it work? how can i start it? how do i know if and why the .fdi script works or fails?
since its a server edition and its purpose should be a very minimized server install i dont want a GUI like gnome fully installed
Ubuntu Installation :: 10.04 Install :1st SATA Port Not Recognized As /dev/sda - Solve This?
May 2, 2010My computer has 2 HDDs attached to 1st and 2nd SATA ports of my mobo respectively, the 1st SATA drive is empty while the 2nd have my Windows Vista on it. I also have a Perc/5i RAID card with 2 RAID arrays defined.
I am going to install Ubuntu 10.04 x64 to the 1st SATA driver (I expect it will be /dev/sda), but when I try to install, I found my drives are recognized as below,
/dev/sda > 1st RAID array of my Perc/5i
/dev/sdb > 2nd RAID array of my Perc/5i
/dev/sdc > 1st SATA drive < I need to install ubuntu on this drive
/dev/sdd > 2nd SATA drive
I don't want to install 10.04 as /dev/sdc because I may add more arrays to my raid card which from my experience of 9.04, it will probably change the drive letter of my current /dev/sdc and then system will fail to boot.
Is there any way to force my 1st SATA HDD as /dev/sda during install ?
Fedora Installation :: After Preupgrade: F15 Doesn't Recognize Sata Disks Connected Through Marvell Controller
May 31, 2011I upgraded F14 to F15; However, F15 no longer recognizes my 3 sata disks connected through Marvell controller. The controller is an integrated Marvell chipset 88SE6480. The controller has its own manufacturer driver but it was intended for RHEL 5.4 (mv64xx) and installation of this driver fails to generate mv64xx driver.
View 3 Replies View RelatedHardware :: Configure The Master And Slave On 5 Sata Disks?
May 13, 2010How to configure the master and slave on 5 Sata disks? Is there that or it is automatic.I install Debian, ok, master boot ok, on the first sataAnd at reboot, just after install, the boot hangs and no grub appears.
View 3 Replies View RelatedCentOS 5 Hardware :: Poor I/O Performance On IDE/SATA Disks?
Jan 13, 2010I've just removed fedora 10 and installed CentOS 5.4 both x86_56 on my Lenovo ThinkCentre 9091-CTO workstation, and observed serious performance degradation while intensive I/O operations and huge load without significant CPU consumption in user mode with about 50% in I/o wait.For example if I do the "tar xjvf some_large_tar.bz" file and run vmstat i get the output below. This is the only cpu and io intensive process running. The load gets up to 6 on C2D CPU and the machine has unacceptable responsivness.
[root@f00 ~]# vmstat 5 10
procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------
r b swpd free buff cache si so bi bo in cs us sy id wa st
[code]....
Ubuntu :: Sata Dock Not Recognized?
Jan 7, 2010OS: Ubuntu Minimal ( OpenSSH, Samba )For some reason my Blacx Duet sata dock is not getting recognized and I am not sure what I am missing but it seems to work when I connect it to a full ubuntu install that is in a VM.Anyone know if something needs to be installed for it to work properly... regular flash drives work perfectly fine.
View 1 Replies View RelatedFedora Hardware :: F13 - Udev Des Not Create Entries For SATA Disks
Jul 17, 2010I have Fedora 13 installed in a new computer, and form some weird reason, udev is skipping three of my HDs. Looging the output for udev --triger, the entries for the HDs are skipped
Code:
[root@storage ~]# lspci
00:00.0 Host bridge: ATI Technologies Inc RD780 Northbridge only dual slot PCI-e_GFX and HT1 K8 part
00:02.0 PCI bridge: ATI Technologies Inc RD790 PCI to PCI bridge (external gfx0 port A)
00:06.0 PCI bridge: ATI Technologies Inc RD790 PCI to PCI bridge (PCI express gpp port C)
00:07.0 PCI bridge: ATI Technologies Inc RD790 PCI to PCI bridge (PCI express gpp port D)
00:0a.0 PCI bridge: ATI Technologies Inc RD790 PCI to PCI bridge (PCI express gpp port F) .....
OpenSUSE Install :: Installer Will Not Detect Hard Disks (SATA)?
Dec 19, 2009Trying to install SUSE on a perfectly working PC that was running Windows. Blew away all the partitions and formated the drives.When trying to install SUSE, Installer will not detect my two hard disks. Tried with version 10.x, 11.1 and 11.2, without success.My Mobo is a XFX GeForce 8209, and my SATA drives are both Seagates (1x120GB, 1x320GB). I've tried different SATA mode selection (i.e. SATA, AHCI, and RAID) without any success either.I've tried to look for SATA controller drivers for my Mobo, to try to load on Installer startup, but failed there too.
View 1 Replies View RelatedOpenSUSE Install :: 11.2 - Dell SAS / SATA Virtual Disks (RAID 1)
Sep 17, 2010I have a Dell Studio XPS running openSUSE 11.2 with dual mirrored disks (using Dell's SATA controller). Does anyone know how I can set up automatic monitoring of the disks so that I will be informed if either fail? I think smartd might be what I need here. Is that correct? I added:
/dev/sda -a -d sat -m <my email>
/dev/sda -a -d sat -m <my email>
smartd is running, but how do I know that it will report what I need? I also have a client with a Dell PowderEdge SC440 with SAS 5/iR also running openSUSE 11.2. They also require automatic monitoring. There doesn't seem to be a SAS directive for smartd. I notice that the newer release says it does support SAS disk. I upgraded to 5.39. On restart (with DEVICESCAN as the directive) I get the following in /var/log/messages for my SAS RAID disk.
Sep 18 10:47:26 harmony-server smartd[25234]: Device: /dev/sdb, Bad IEC (SMART) mode page, err=4, skip device
I ran:
smartctl -a /dev/sdb
and got the result:
smartctl 5.39.1 2010-01-28 r3054 [x86_64-unknown-linux-gnu] (openSUSE RPM)
Copyright (C) 2002-10 by Bruce Allen, smartmontools
Device: Dell VIRTUAL DISK Version: 1028
Device type: disk
Local Time is: Sat Sep 18 11:32:08 2010 JST
Device does not support SMART
Error Counter logging not supported
Device does not support Self Test logging
Is there some other tool/package that does support DELL virtual disks?
Hardware :: Two SATA Disks:counldn't Find Partitions In The Second Disk?
Sep 1, 2010I have two SATA disks, 80G and 1T. Using "df" command we can see the all partitions:
/dev/sda3 6.7G 2.5G 3.9G 40% /
tmpfs 1.7G 0 1.7G 0% /lib/init/rw
udev 1.7G 220K 1.7G 1% /dev
[code]...
Ubuntu Installation :: Which Disks Can Be Main Boot Disks
Mar 31, 2010I have/had a PC with several hard drives, and a mix of ubuntu and windows on multi boot.The old boot drive died screaming, and I need to start again. (But my data is safe! yay!)
Is there anything special about which drive can be the main drive to start booting from? Or to put it another way, can I install to any of the other 3 and expect it to work, or do I need to switch them around so a different drive is on the connections for the recently dead one?
OpenSUSE Hardware :: External SATA Drive Not Recognized / Cant Recreate The Partition On Server?
May 2, 2010OpenSUSE 11.2 server, Gigabyte GA-MA790X-UD4P sda for system, 3 ext4 partitions, working fine.sdb promise RAID1 for data, 1 ext4 partition, working fine.sdc is an eSATA docking station for data backup, 1 encrypted ext4 partition -- here lies the problem.
This configuration has been functional for months until I decided to add two more external drives (sdc) to rotate through backups. I had difficulty with encyption on the first new drive and eventually decided to start over. Using the gui Yast Expert Partitioner, I deleted the single partition. That began a real nightmare...
Since deleting the partition, the system detects drives inserted in the docking station, but does not report them (including a different fully functional drive and a brand new unused drive). I have tested all drives on other computers and they function perfectly. I have rebooted the system several times while troubleshooting this issue.
Could not recreate the partition on server (since it does not recognize the drive), so I used Gparted on another computer - it all went without a hitch, formatted ext4. But when I placed the drive in the dock, the drive still was detected but not recognized.
Details:
BIOS lists the eSATA drive
Entering Yast Expert Partitioner, error message follows:
The partitioning on disk /dev/sdc is not readable by the partitioning tool parted, which is used to change the partition table.
You can use the partitions on disk /dev/sdc as they are. You can format them and assign mount points to them, but you cannot add, edit, resize, or remove partitions from that disk with this tool.
Yast partitioner shows drives: sda, sda1, sda2, sda3, sdb, sdb1 sbc is not listed.
# fdisk sdc results in: Unable to open sdc
# dmesg | grep tail reports:
[48442.370779] sd 0:0:0:0: [sdc] Unhandled error code
[48442.370793] sd 0:0:0:0: [sdc] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
code....
So how did partition deletion cause this issue, and how do I correct the problem? It is possible that my difficulties encrypting the first new drive are related (it's not my first time doing it successfully). It seems the problem is in the Kernel or configuration. I have invested many hours in forums and on google - tried dozens of possible fixes. I'm beginning to suspect system corruption or a bug, however all other system functions are working perfectly.
Hardware :: Can SATA 3 (SATA III) Hard Disk Be Run On Motherboard Which Only Support SATA II
Aug 13, 2010Can SATA 3 (SATA III) Hard disk be run on motherboard which only supports SATA II, except sacrificing the speed (throughput)?
View 2 Replies View RelatedUbuntu :: SATA II / Error "ata4: Limiting SATA Link Speed To 1.5 Gbps" - Allowing The SSD To Run At SATA II Speeds?
May 1, 2011I keep getting this error in my log viewer every 2 seconds: Code: ata4: limiting SATA link speed to 1.5 Gbps I have a dual boot SSD and I have run many SMART tests in windows and linux, (using smartmon tools and the disk utility) and the reports are all 100% healthy..... My research shows that this error represents one of the following:
1. Problem with SATA controller
2. Changing BIOS to allow SATA
3. Changing SATA mode to PATA or AHCI
4. Replacing the SATA cable
5. Allowing the SSD to run at SATA II speeds, i.e. 3 Gbps
- Does anyone know how to try number 5, i.e. allowing the SSD to run at SATA II speeds? I am lost here and this problem has caused my machine to crash twice when watching a movie in linux/ ubuntu. (It is worth noting that the crashes have only occurred in linux and I have never had an issue in windows, so it does seem to be a linux setting somewhere, hence why I think it is a "allowing SATA II to run at correct speeds issue")
Ubuntu Installation :: Ubunto 8.04 Cannot Detect Sata Hard Drive Or Sata Drive Cdrw?
May 28, 2011ubuntu 8.04 server can not detect seagate sata hard drive 2tb or sata Lg dvdrw x22 sata drive .is it possible to install it without buying a pci ide sata card?is it possible to get a driver for sata driver and sata drive that can be recognise by ubunto 8.04 server ?or to get the files for 1.44 floppy diskdoes the late edition of unbutu recognise sate hdd and sata cdrw drive automaticly during the installation of the unbutu?
View 1 Replies View RelatedOpenSUSE Install :: All Drives Not Recognized On Install (SATA 6)?
Jan 15, 2011I just built a new system which has 4 SATA 3 Drives and 2 SATA 6 drives. The motherboard is an Asus P6X58D Premium which has 2 SATA 6 ports through a Marvel controller.I have Windows 7 loaded on one of those SATA 6 drives and it recognizes and boots fine. My intent was to load openSUSE 11.3 on the other SATA 6 drive all by itself and then use the SATA 3 drives as other file systems. When I go to install, the only drives that the openSUSE installer sees are the 4 SATA 4 drives, the SATA 6 drives do not appear at all. Note that when the system boots from the DVD the load of the Marvel Controller says IDE Passthrough Mode and displays those two drives. So how do I get openSUSE to see those drives so I can install and setup Grub to boot from there. I'm afraid if I install to just the SATA 3 drives, then I'll never get to Windows 7 again (should I ever need it ) without much gyrations. I've also tried booting from gparted-live and it does not see them either.
View 9 Replies View RelatedProgramming :: C - For System Calls, Is Blocking Or Non-blocking Default?
Mar 23, 2010For system calls, is blocking or non-blocking default in C? Simple question, just am not seeing the answer super quickly.
View 4 Replies View RelatedProgramming :: Blocking And Non Blocking TCP Send/recv?
Dec 25, 2010I have a device that is working on modbus protocol andI have written a small program(with block TCP read method ) to read its registers via modbus protocol.my program is working very well but except those times that I unplug the Ethernet cable or turning off the modbus gateway during programs work.at this time my program stops on recv system call (if it reach this system call exacly when I unplug Ethernet cable or turning off the modbus gateway during programs work).I changed my source to work in nonblock TCP method, at this time with the same situation my program does not stop/block on recv system call but after pluging back the Ethernet cable or resuming the connectivity situation back it reads data incorrectly .this is my code:Quote:
#define DEBUG
#include <fcntl.h>
#include <string.h>
[code]...
Ubuntu :: SATA Libata Verses Silicom Images SATA Module
Jun 21, 2010I installed Ubuntu 10.04, and happened to have an Silicom Images PCXpress card plugged in, and it kindly added the sil_sata module.This is fine for this chip set.I think that my earlier installation of Ubuntu 9.04 used Libata, which does support NCQ and also has good legacy support for the Intel Intel ICH7 chipset I have inside my Sony Vaio SZ notebook. Also, libata also support Silicon Image chipsets as far as I can tell from URL...I wish to remove the Silicom Images SATA modules and replace this with libata and then test the performance between the two device drivers.
View 5 Replies View RelatedUbuntu Installation :: Blocking The Application In 10.04?
May 25, 2010I need assistance blocking application in Ubuntu 10.04. block all applications for certain users if they do not exist in a certain directory.For example,we would like to prevent users from launching a portable copy of Firefox from a portable HDD or Flash drive.
View 1 Replies View RelatedDebian :: Check If Mainboard Supports SATA-I Or SATA-II?
Jun 1, 2010My motherboard supports SATA but I do not know which version: SATA-I or SATA-II. I want to buy a SSD so it would be pointless to buy a fast SSD if my motherboard only suports SATA-I
View 7 Replies View RelatedFedora Installation :: 12, Upgrades Internet Blocking?
Feb 26, 2010Have an issue after an upgrade to connect to the internet using Firefox and Thunderbird.Can perform upgrades and use the Ping command.Have configured the Firewall as per the guidelines.[URL]
View 2 Replies View RelatedUbuntu Installation :: 9.10 - No SATA Drive In Installation's Partitioner?
Feb 17, 2010i have a strange problem while trying to install Ubuntu 9.10 64bit (also tried with x86 - no luck).My system specs : Motherboard : ASUS P5B VM SE (PATA : JMB368 / Intel ICHHD : Seagate SATA II 3GBit 320 MB (connected in SATA port 1)CPU : Intel Core 2 Quad 2500 GHzI must state i installed Windows 7 without a problem. After that, i tried to install Ubuntu 9.10, first 64bit then x86 but in every case the setup starts, i select language / location etc and when the partitioner starts i see no hard disk drive. Same happens if i try the alternate install cd.
I must mention here that if i click on "Exit" and access Ubuntu Live CD desktopm i can go System >Administrator > Disk Utillity and GParted. In both utillities my HD shows up just fine. So what could be the problem ??? I tried starting ubuntu with pci=nommconf irqpoll -> no luckHere is the lspci output :
ubuntu@ubuntu:~$ lspci
00:00.0 Host bridge: Intel Corporation 82P965/G965 Memory Controller Hub (rev 02)
00:02.0 VGA compatible controller: Intel Corporation 82G965 Integrated Graphics Controller (rev 02)
[code]....
Ubuntu Installation :: Not Detecting Disks 10.10
Apr 9, 2011I am attempting to install ubuntu 10.10-alternate-i386 that was burned on a cd.
Motherboard: SOYO SY-K7ADA v1.0-2AA1
Main Processor: AMD Athlon 1700+
Primary Master: WDC WD800AAJB-00J3A0 0.103E01
The HDD is brand new and hasn't been formated, partitioned, or previously had any other OS on it. The HDD is recognized in the BIOS.A list of possible drivers are listed in which don't match, except for two, but they don't lead to anywhere beneficial in order to complete the installation process.At this point, I have no idea how I must proceed.
Ubuntu Installation :: 11.04 Cannot Mount Two Of Disks?
Apr 29, 2011I did a fresh install of 11.04. It didn't let me choose custom mount points for my disks, so I left non-system partitions unmounted in the installer. Big mistake. It seemingly screwed with two of my disks. I can see them in disk utility, but disk utility cannot identify partition information.
@fridge:~$ sudo mount /dev/sde1 /m2 -t ext4
mount: wrong fs type, bad option, bad superblock on /dev/sde1,
missing codepage or helper program, or other error
[code]....
Ubuntu Installation :: Do The 11.04 Disks Available For Download
Sep 1, 2011Do the 11.04 disks available for download contain the latest, current, kernel release?
View 3 Replies View Related