Is there a utility app that will allow 'ghosting' your current Linux harddrive to another. For example, my current drive is 40Gb, I'd like to ghost/clone it to a 320Gb harddrive. Using an app like this saves re-installing the O/S, software, configuration and allows making a disaster-recovery drive.
View 3 RepliesCode:
user01@ubuntu:~$ sudo gunzip -c /media/xbox/xbox_image.gz | dd of=/dev/sdc
dd: opening `/dev/sdc': Permission denied
[sudo] password for user01:
[Code]....
I'm getting Permission denied even though I'm putting sudo in front of the command but, instead of asking me for a pass word it just says Permission denied "then" it askes for a pass. I enter the pass and it just takes me to the
user01@ubuntu:~$
prompt. I enter the command a second time and it says Permission denied again.
I want to move the entire contents of my backup HD to another HD. I could manually copy everything, but I was hoping to clone the entire backup hard drive. I tried to do it with Gparted, but as far as I can tell, I can't clone between drives, only between partitions on the same drive (I've done that before). So how can I do this in Linux? I think one of my drives came with a cloning utility on a CD, but I'm not sure I still have the CD.
View 2 Replies View RelatedHere's what i'm trying to do: i have a 300GB IDE hard drive that has a OpenSuse build. I am trying to replicate this HD so that i can have another box similar to the original one...my second drive is 500GB SATA.
So far, I just ran a 'dd' command to copy the 300GB to 500GB. Now, after having read on internet, i realized i need to change fstab & /boot/grub/menu.lst. specifically, we need to change for ex:/dev/disk/by-id/ata-Maxtor_7L300S0_L60LCJ0G-part1 to /dev/disk/by-id/sda1 i did use a Ubuntu LiveCD to access the fstab and changed the line as mentioned above. Now, how do i change the menu.lst?? right now, when i try booting up from this HD, i have issues. specifically, i get this error message: could not find /dev/VolGroup00/LogVol00
I am getting a new 4kb sector HDD for my laptop, WD scorpio black 750gb, I would like to image existing partitions on 512bytes sector HDD and move them to the new 4kb sector HDD, what's the best way to do this.
present config is as follows:
Disk /dev/sda: 80.0 GB, 80026361856 bytes
255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
[Code].....
I am planning to keep the same three partitions as the primary partitions on the new drive and add few more logical partitions. I would have liked to move to GPT but since I need Win 7, I am stuck with MBR partiotion table.
Now, I understand how to partition an Advanced format disk, what I want to know is how to move the existing partitions on the 80 Gb disk to the new disk?
I use Clonezilla to copy partitions but it is not compatible unless both the target and the source disks are already using 4096 sector size.
I can use Acronis True Image WD Edition to clone Win 7 but how do I clone Ubuntu?
Also my Laptop's chipset is limited to SATA 1.5, will it cause any issues, I know the bandwidth is not an issue.
Recently my had disk crashed. It has taken me over a day to install and setup the drive - time I can't really afford. I'd like to know how I can clone a second as a bootable copy of the main hard drive and update from time to time. Therefore if the main hd fails again, I can simple boot from the second drive.How can I do this? I have two sata drives in the box, running 10.10 desktop.
View 1 Replies View RelatedRecently my had disk crashed. It has taken me over a day to install and setup the drive - time I can't really afford.I'd like to know how I can clone a second as a bootable copy of the main hard drive and update from time to time. Therefore if the main hd fails again, I can simple boot from the second drive.
View 1 Replies View RelatedI just invested nearly 12 hours configuring a CCTV system using CentOS 5.5 Server and Zoneminder. I have it setup just the way I want it. I would like to make a clone image of the drive just in case disaster strikes (lightning strike, failed hard disk, etc). In the Windows PC world, I use a program called Ghost to make a mirror image of a hard disk. I power the computer down, run Ghost to make a block level clone of the drive, then power it back up. Can I assume that will work with CentOS without problem?
In the computer now is a 320GB SATA drive. One partition on it is swap, and the other is ext3. There is no raid setup on the drive. I have an identical 320GB drive I could use and keep it in the computer unplugged from the power and not spinning. That way if anything ever happens, I can power down, move the power and data cable to the new drive and power it back up. Granted, I will lose any new config and database changes, but it will be a lot better than starting back at square 1 and reconfiguring the entire OS and software.
I am trying to clone my internal drive on my laptop using the dd command after starting up my computer using the 10.10 installer CD. Nothing happens when I follow the instructions from this site: [URL] When I follow these instructions, it doesn't work. I know that I am not being specific here but all I can say is that nothing happens. What am I doing wrong. My internal drive is 250GB and the partition I created on my DOS formatted external drive is 250GB as well.
View 9 Replies View RelatedI'm trying to make an image of my whole hard drive (320 GB) to save on an external hard drive. I'm using Ubuntu Jaunty Live CD to do it, with this command
Code:
sudo dd if=/dev/sda | gzip -c > /media/ExpansionDrive/imagedd.img
At the beginning everything is going fine, but after few hours the transfer rate is incredibly low. After 1/2 hour, 20 Gb have been copied.
After 1 hour, 27 GB
After 2 hours, 40 GB
After 4 hours, 54 GB
After 8 hours, 71 GB
Is it normal? I've also tried to use ddrescue, but I have the same problem. Is there any other tool to clone hard drive with a constant transfer rate?
I have a rock solid server running CentOS 5.3 (probably 5.4 soon enough). Basic LAMP box with a few tweaks thrown in. Everything is running perfectly, with one problem - the drive is too small (I project it filling up to dangerous levels in 6-8 months). So, what I'm looking to do is basically clone the drive, store the image, pull the current drive and replace with a bigger drive (same number of heads and cylinders though), and install the image.
What I did do once, a million years ago, is put the new drive as a slave on the same IDE cable, and use dd (working from a live CD of the distro) to copy from the master (smaller) to slave (larger). Then, yank the smaller, change jumper on bigger drive from slave to master, and away I go. Next step as I recall was using gparted to get access to all the space on the new, bigger drive.
Is this more less still a reasonable way to go? I recall the issue was making sure the old smaller and new larger drive had the same number of heads/cylinders (although I don't remember exactly why).
I would like to replace my old 100gb boot drive in my server with a new SSD...for obvious reasons. So what is the best way to clone the existing installation (10.04 desktop) from the old boot drive onto the new SSD? I have read some guides online that suggest using the live CD and various software packages but most of them say it will only work if you are cloning to a disk of the same size or larger, nobody seems to address taking an installation from a larger volume down to a smaller one - in my case a 100gb IDE onto a 30gb SATA SSD.
As this is a datadump, the only drives I really care about are the various 1.0/1.5tb drives that actually store the data, the OS drive contains nothing more than the standard OS, samba/webmin and a few monitoring tools. So I guess it's not the end of the world for me to start fresh and install 10.10 next week, but I would like to know for the sake of this upgrade and future ones if anyone can be of assistance. basic specs if needed: Athlon64 X2 3800, 2gb DDR500, Asus A8N SLI Premium (Nforce 4/Silicon Image 3114R RAID controller). OS is on a 100gb IDE (WD1000BB-00C) and I would like to toss it on a Kingston 30gb SSD (SNV125-S2/30).
When I first switched from windoze to Fedora I trimed a bit of space off the end of the HDD, formatted it to ext3 and installed Fedora 14 there. I have now completely rebuilt the machine and put a 2TB drive in. My intention was to upgrade to Fedora 15, but after a few weeks trying to get the new gnome to anything resembling useful, I gave up and decided to go back to the reliable 14.
I tried the old drive, and everything worked great, so I though no problem, clone that over to the new drive, and job done, no need to mess about for weeks getting all my settings back. I booted from the old drive with both connected and ran gparted, It sees both drives but won't let me copy the old partition. It complains about 'LMV is not yet supported' I tried booting from a gparted ISO with the same result.
How can I get this sorted? I've got work needing done, I don't have time to start from scratch (*AGAIN*),
My dad passed away 2 years ago and he had a toshibia laptop, and today I've decided to start using it. I would like to reformat it to Arch Linux from Windows XP.
He has a 80gb hdd with everything on one partition (thats how windows does it). I would like to create another partition (~20gb, and I know how to do this) and have clonezilla clone the main partition and save it to the 20gb partition. This is because you can't clone and save to the same drive unless its partitioned. (I'm saying partition lot).
Anyway my fathers computer is very important to me, and having it remain intact as he left it is very very important to me. I know the easiest and most sarcastic response is to tell me not to use it, but I want to use this computer.
Does anyone have experience with clonezilla? Will it back up the ENTIRE HDD like it says it will, without missing any important documents and files scattered throughout the disc? And when I do finish the cloning, format, and at a later date restore using the image I copied, will it be like I never touched it?
I have a Shuttle XPC with 3 drives. /dev/sda is a 320GB SATA drive with a basic installation. Two partitions, a swap and the rest is on /. The other two drives are 1.5TB SATA configured as a software mirror as /dev/md0.
I want to use dd to clone the 320GB boot/OS drive to a 750GB SATA I have at home. Last night I put the 750 in a USB enclosure and at about 6:00 PM fired off: dd if=/dev/sda of=/dev/sdd
It's now 7:16 AM and the dd is *STILL* going. Is this unusually long to clone the drive? Is there any way to check the progress or a way to launch dd with a progress indicator?
i am running ubuntu 10.10 and windows7 on a asus eee 1015. currently i have two partitions: 80GB for windows (NTFS) and 160Gb for Ubuntu (ext4).
I want to:
- shrink the windows partition (easy, no worries);
- Shrink the ubuntu partition
- join the space thus created in a third partition that i can use for storage, media etc accessible by both windows and ubuntu
The problem:
- i could not manage to get gparted live to run off USB stick (i get the unable to find medium.... error)
- even if i would get gparted to work and i succeed in shrinking the ubuntu partition as well, the two spaces reclaimed will be divided by the ubuntu partition, which means they cannot be joined in a third partition.
so here is what i want to do:
- shrink windows and create a new partition;
- format this new partition as ext4;
- somehow "clone" the data on my current ubuntu root into the new partition;
- format the current root as NTFS and use it as the storage partition
i am aware this may mean i would have to re-set grub etc but would the cloning of the partition be possible? that i would need to clone data from a 160G partition into a 40G partition.
BY THE WAY - forgot to mention that i have tried to load clonezilla off an USB drive and i get the same error: "unable to find medium..."
I have used GParted several times but I only know how to clone a single partition. I am looking for a way to clone and entire drive that has several partitions, along withthe MRB, unpartitioned space and everything else in one step. I have a 500 GB drive that is going out and I want to clone it to a 1 TB drive so I don't have to reinstall 3 different OSs and fix the GRUB. One of the other OSs is on anther drive so I'm not sure that it would work even if I can clone everything exactly. I'm not sure if the drive that is failing is the one with the MBR on it or not. how to do this in GParted or know another good program I can run from a live CD to do this?
View 2 Replies View RelatedI've decided that I want to use another, smaller, hard drive for my OS and I'd like to clone /dev/sda onto /dev/sdc. I want it to be an exact clone except my partition for my "/home" will be smaller (since there's not room for it). I was gonna try with dd but I'm not sure if I should build the partition table and use dd-command on one partition at the time? Will this then include GRUB boot loader and will it be working properly?
Do I have to clone the disk completely for it to boot properly? I'm not sure how or where GRUB places itself on disks as you install it. Can I perhaps copy the partitions one by one and then install GRUB from CD afterwards? Should I leave some unallocated space somewhere in between the partitions as I build and clone them?
I got a dell inspiron 1501 laptop with a 80Gb sata drive what is the best solution to add data storage space for someone that love to have multiples operating systems at hand Note: I use mostly linux so I won't need to change my laptop for many years maybe ...
View 2 Replies View RelatedMy parents bought a new hard drive for a laptop that I've owned for several years. It's much larger than the current one, so I plan on splitting it up to dual boot it with Ubuntu.I have no problem with partitioning a drive (I always keep a LiveCD handy), but my question is this: how can I go about moving the existing partition to the new drive? This is a laptop, so I can't simply plug the new drive into another slot.
Also, even if I manage to move it, will Windows still work on the new drive in a larger partition? I've had this laptop for quite a while, and I've lost the recovery discs that came with it a long time ago. I also have a lot of software without CDs to reinstall them with. This makes not reinstalling Windows a high priority.
Trying to install Fedora 12 using the 6 CDs. Trying to install on an older x86 box.Problem is that when detecting my hard drive, Fedora 12 recognizes it as a sda hard drive instead of hda hard drive. I have no SCSI connected to my computer what so ever. It's an old fashion PATA Western Digital hard drive.If I proceed with the install, Fedora 12 only installs 200MB of the OS from the first CD only. No options for additional software or anything.
View 1 Replies View RelatedSometimes when I do anything write heavy such as transferring backup or downloading large files from the net, the machine crashes almost completely.
View 8 Replies View RelatedI have a laptop with only 30GB storage and I want to install Lubuntu in virtual box but Lubuntu needs 5GB of storage space which i dont have. Could i use an external 160GB hard drive to act as the hard drive for the virtual machine without affecting the files that are already on the external hard drive
View 6 Replies View RelatedI have 2 ubuntu's: 1 on my ineternal hard drive, 1 on my external
When I startup without my ext drive =>GRUB error 21.
And when I plug it in I can choose: the standard ubuntu kernel is the one on my external, and the original one is listed under other...
I'd like to be able to startup without external hard drive and make the ubuntu on my internal drve the standard.
I have a laptop running dual boot which I would now like to convert to single boot (Ubuntu only).
I have recently had some very good experiences with VirtualBox (It's fantastic!) and so the idea that I have is to 'migrate' my whole Windows environment from 'dual boot' to VirtualBox.
I know that this can be done with such products as 'Ghost' where you take a snapshot of a whole (Windows) system and then you can recreate this (from DVD).
Here I'd really like to know whether Ubuntu (live CD) offers a similar tool so that I could copy my whole Windows setup, save it to DVD and then simply 're-install' it on a new VirtualBox machine.
That would save me absolutely masses of configuration work!
I made a multi boot USB using Grub 2 and Grub4DOS (with some help of liveusb.info) which works perfectly fine cuz I tested it my self.
Now I want to GHOST an image of this multi boot so when ever I want to ghost it on another thumb drive, I can easily do it. But when ever I make the ghost image and I try to put it on another thumb drive and try to boot from the newly ghosted thumb drive to test it, it will give the error below:
loading.
error: the symbol `grub_puts_` not found
grub rescue>
I tried SO MANY different techniques to find what the problem is. I tried making the multi boot using Ubuntu 9.04, 9.10 and 10.04 (which I think doesn't have anything to do with this but doesn't hurt to try!). I tried reghosting on the same brand and same size thumb drive and lots of other tries but I can't figure this out.
what do you use to make an image of your bootable thumb drive?
I am trying to get rid of shadows on all my text that has appeared today. This happens using Firefox,Chrome and Opera browsers. Usually I Google any problems and a solution normally pops up via Ubuntu Forums but no luck this time.
View 9 Replies View RelatedI want to know that can we install Ubuntu OS like ghosting in windows.In windows if we install through ghosting then we do not need to install drivers and application software.Is it possible in Ubuntu? if possible then what is the process?
View 1 Replies View RelatedI recently bought 320 GB Trancend external hard disk and working fine days back.Earlier i could copy from and to the hard disk with out any issue. I dont know what happened after that now i am not able to write any files in to the external hard disk. This is not NTFS formatted device. here is some of the out put from terminal.
Code:
sundar@sundar-sundar:~$ fdisk -l
Disk /dev/sda: 120.0 GB, 120034123776 bytes
[code]...
I have been trying to install centos on my hp servers and when i get to partitions my hard drives the OS does not detect any harddrives. I have 4 scsi drives and i believe a intergrated smart array controller.
View 1 Replies View Related