Kubuntu 10.4DVI-0 SyncMaster931BFDVI-1 BenQ G2220HDAI set the monitors with Display SettingsEverything works fine until rebootI lose my settings and always returns to the initial state
View 4 Replies
I have dual monitors running successfully with my BFG GeForce 8400GS and NVIDIA X server settings. The only problem is every time I restart, the settings go back to default, so I have to setup the dual monitors again.
View 5 Replies View RelatedThe 'Multiple Screens' tool, aka grandr, is very handy for setting up my dual monitors. But restarting my system restores the monitor setup to the (crummy) default settings. Is there a way to save these settings and make sure they are always applied when the OS boots? Putting these settings in my xorg.conf would be fine, but I'm not sure where or in what form the settings generated by grandr might be located, or if they're at all xorg.conf compatible.
View 2 Replies View RelatedI've a laptop with 2 external monitors connected to it.Using SaX2 I can't configure it in a way where it only uses the two external monitors and not the laptops own screen.With nvidia-settings I can configure it properly, as I am however unable to save it due to a missing xorg.conf file how am I supposed to save the this config so it isn't 'forgotten' between reboots?
View 2 Replies View RelatedWhen I try to run the 'system-config-display' program for Fedora 11 and I use the dual head tab, attempting to save the settings results in this:
Traceback (most recent call last):
File "/usr/share/system-config-display/xConfigDialog.py", line 212, in ok
if card.getDescription() == self.secondVideocardOptionMenu.get_menu().get_acti ve().get_data("NAME"):
AttributeError: 'NoneType' object has no attribute 'get_data'
And it won't save the data.
Config a CentOS iptables.I issued some iptables rules.the rules were effective at once.Then, I came with a "iptables-save", but the "/etc/sysconfig/iptables" file hasn't been updated, it still loads the defaults rules with CentOS after reboot.
View 4 Replies View RelatedI want to be able to login on different users on my two screens. Is that possible? It would be nice if I could have the left screen and my gf could have the right. I'm using ubuntu 10.04 with gnome, and I have a Nvidia graphics card.
View 8 Replies View RelatedI have triple monitors working on my 10.10 ubuntu system and they work for most things. Except k9copy and virtual box will cause x to restart. glxgears works fine.
xorg.conf
Code:
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 260.19.06 (buildd@yellow) Mon Oct 4 15:59:51 UTC 2010
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0" RightOf "Screen1"
Screen 1 "Screen1" 0 0
Screen 2 "Screen2" RightOf "Screen0"
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
Option "Xinerama" "1"
EndSection .....
I have a Dell inspiron 1525 laptop with a 1280x800 display and an external 1280x1024 monitor. I'm using 9.04 with openbox. I've done a loooot of online reading about how to get a dual monitor setup using xrandr, and I really don't know what I'm missing here. So here's the deal: I want to have my external monitor on the left of the laptop's display, and of course I want each of them to display different parts of the desktop.
First I set up the right resolution to each one of them (I do it using lxrandr). Typing xrandr -q in a terminal, I get the following:
[Code]...
I have an asus p5kpl-cm MB. I plugged in a radeon 9200 pci card. In the bios, I can set up:
pci/igd
igd/pci
igd
etc.
This determines which of the 2 displays (pci card or internal graphics on the MB) is the boot display. That determines which comes up with the bios screen and then once booted into ubuntu (10.04), this is the only adapter/monitor seen. The button detect monitors doesn't do anything.
lspci sees both my internal and pci card graphics. So, I can get either to work just fine (auto detected etc.) just not both at the same time.
I've tried all of the 3 above settings, and even when I set it to just igd, lspci still sees both my adapters. It identifies them correctly, and it works perfectly, detecting the monitor and knows the resolutions for each - just not both at the same time.
Does ubuntu know how to automatically configure more than one display w/o doing something else, or must I do something else to get both going together?
Code:
$ lspci
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10)
00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 10)
[Code]....
I've always used Debian with a single monitor and no need of proprietary drivers, because I usually don't do graphics or multimedia. Now I'm asked to set-up a machine with 3 nvidia video cards (770) and 4 monitors and everything went south. I started with just 2 monitors connected to 2 different video cards, not wanting to push my luck.
I installed a fresh Jessie and followed the instruction to install the nvidia drivers and tools from the Wiki. Everything went smooth. After reboot I executed (as root) nvidia-settings and I configured the two monitors to be one to the right to the other, with BaseMosaic option (at this point just one monitor was active) I saved the configuration to /etc/X11/xorg.conf , I even executed nvidia-xconfig as suggested, I rebooted and nothing happened, only one monitor was working, while the other -- looking again in the nvidia settings -- was still disabled.
I then tried with xinerama option and things are even worse, since now both monitors are black. I can login in one textual shell, but then I don't know what to do, since in my 10+ years of linux ... I never had to mess with X server. Is there a way to at least recover a working X without reinstalling everything?
I'm having trouble setting up dual monitors on my HP Pavilion dv7-1020us laptop, with an Nvidia 9600M GT graphics card, and Ubuntu 9.10. I installed Ubuntu via Wubi, on top of Windows 7. I tried this before on the same laptop when I was using Vista and Wubi, and Ubuntu was able to recognize my Graphics card, and install a proprietary driver. I wasn't able to test dual monitors, though. However, now that I'm using W7 and Ubuntu, it cannot use a dual-monitors correctly. It recognizes the monitor, but it only displays a mirror display of my Laptop monitor, not acting as a separate monitor, like I want it to. I tried messing around with the settings in the display menu, but nothing works. I tried downloading linux drivers for my card from Nvidia's site, but the file is in a .run extension, which I don't know how to install. What should I do to get this working?
View 7 Replies View RelatedI have a ATI VisionTek 9250 128mb DMS59 PCI video card that I would like to use for dual monitors on Ubuntu 10.04 Gnome. I installed the card and booted the live cd. Both monitors are recognized when I go to the display settings, but when I un-check the mirror box, nothing changes. I am still only getting one monitor. I was previously using 9.10 and it sometimes worked, but not always.
View 5 Replies View RelatedI just downloaded Ubuntu 10.10 and installed it today. I was just wondering, does Ubuntu support dual monitors? I tried looking through the settings in Ubuntu but I couldnt figure it out.
View 1 Replies View RelatedI have a brand new installation of Ubuntu 10.10. I'm using a GeForce 8600GT graphics chipset. I have two monitors, and my goal here is to have them both working under Ubuntu in their full resolutions, and I've not had any luck with this yet. I've got a Viewsonic VE155s with a native resolution of 1024x768, and a Chimei CMV 221D with a native resolution of 1680x1050. When I first installed Ubuntu, both monitors were working, and the VE155s was working in its native resolution of 1024x768, but the CMV221D was stuck in 640x480.
The Nvidia video configuration utility was not identifying the latter monitor - it only reported it as DFP-0, and doesn't allow any resolution above 640x480 to be set. The mechanism (which has a name which I don't recall) which allows the OS to interrogate the monitor's firmware to find out the monitor manufacturer, model and accepted resolutions and frequencies to use does not seem to have worked. (I previously had the Nvidia driver installed, but I've since switched back to the default open source vesa driver. I won't use the closed Nvidia driver if I don't need to, but if I need to use it to get acceptable performance from this hardware than I will.)
So I did a little bit of reading and I did some hacking of xorg.conf. Previously I had the 15" monitor working in 1024x768 and the 22"
monitor working in 640x480. Now I've got the 22" monitor working in 1680x1050 as desired, and the 15" monitor not working at all. Here's a copy of my xorg.conf. For the sake of brevity I have not included the unnecessary bits such as input devices.
Code:
Section "Device"
Identifier "NVidia"
#Driver "nvidia"
[code]...
I'm trying to set up my monitor and tv for dual display but I'm having some problems. I want them to display the same thing so I've enabled twinview and I figured the second display position should be set as clone but when I save xorg and restart the x server the position reverts to absolute. Anyway, the monitor is set as the primary display and it's the one I'm having problems with. The tv is fine but the monitor's display is stretched off the screen so I can't see the far right or bottom of the screen. I'm very new to linux and I'm just finding my feet so if there's any other info needed you'll probably have to be very specific.
View 2 Replies View RelatedThe problem is that I don't have NVIDIA graphics card These are my HP ProBook 4510s Laptop's specification: [URL] And I think my built-in graphics card is Mobile Intel� 4500MHD Did anyone Dual Monitor with this Laptop or knows how to Dual Monitor with it?
View 3 Replies View RelatedI'am using the explicit match 'quota' with iptables. I wonder how can I save quota between restart for every rule. All the quota resets at reboot.
View 1 Replies View RelatedI have a thinkpad T43 with a dock and a 19" Dell monitor attached. Im trying to get an extended desktop.Using the default display program (using ubuntu 9.10) I can mirror the screens just fine. But, when I click the radio button to enable the extended desktop, the monitors (both of them) go black. Some times it doesn't come out of this. (yes, I'm waiting more than 25 seconds) What can I do to make the extended desktop work? here is my display info from the command lshw:
*-display:0
description: VGA compatible controller
product: Mobile 915GM/GMS/910GML Express Graphics Controller
vendor: Intel Corporation
physical id: 2
[Code]...
I want my video card to stop processing an image to my integrated monitor and only process images to my external monitor.
My problem is that I use my Toshiba Satellite M65 (which is a laptop) as a desktop: I use an external monitor, external keyboard, and of course an external mouse. I only recently started using Ubuntu after many years of Windows XP and I just realized that both my laptop's integrated monitor and my external monitor are 'on', displaying the same image. I want my video card to stop processing an image to my integrated monitor.
I've been searching around and from what I've found this is supposed to just work but I am having some display issues when cloning my laptop to an external monitor. I think the problem is that my laptop has a better resolution than the monitor. Here is my setup:
laptop with a display of 1900x1200
external monitor with a display of 1680x1050
ideally I want to clone the laptops output onto the external monitor so they can both operate in their native resolution. When I setup twinview and set it to clone the laptop displays correctly, however, the external monitor is missing a large chunk on the bottom and right hand side
here's my xorg.conf
Code:
# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildd@palmer) Fri Apr 9 10:35:18 UTC 2010
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0" 0 0
[Code].....
Does anyone know of problems where 10.10 doesn't recognise more than one monitor? I've got nVidia 8500GT and I have the 'recommended' proprietary driver installed. I upgraded from 10.04, and dual monitor was working -> restarted -> dual monitor not working.
View 9 Replies View RelatedI'm currently running Ubuntu 10.10 on my HP laptop with an external monitor attached. I've been having the same issue since 9.04 and just now figured I should ask about it.When I have dual monitors set up (extended desktop) the mouse speed in the X direction seems to double. ie. assume the mouse usually moves 1 pixel at a time, it now moves 2. It seems to be functioning as usual in the Y direction, which makes the motion really weird and hard to use. I'm using a Wacom tablet for the mouse, but the same happens with my laptops touch pad. Anyone else experience this/know how to fix it?
View 2 Replies View RelatedI have a dual setup and just switched from Xubuntus Xfce? to Fluxbox... But now I can't set wallpapers on both my screens anymore. How do I do that? I had to change the Fluxbox menu from Head 1 to Head 2 to get it on my bigger, primary screen. Which is the one getting a wallpaper when I'm setting one.
Here's my xorg.conf:
Code:
Section "ServerLayout"
Identifier "X.org Configured"
Screen "Screen0"
InputDevice "Mouse0" "CorePointer"
[Code].....
So, for work purposes i decided to plug my old lcd monitor into my laptop so that I could have my writing on one screen and my info on the other. So i plugged it in and opened up monitor which automatically configured it. Only problem is that now on my laptop screen theres big blank spots on the bottom and on the left. No window will appear there but for some reason docky will.
View 1 Replies View RelatedI just built a system with an Nvidia GT240 and Ubuntu 10.10. I have two monitors and am trying to get them set up. I currently have them working fine in twin view but I'd like to have set up as separate X screens. However, whenever I do that X crashes. I've got the latest drivers set up from the x-sane PPA so I'm not sure what more I can do. My driver version is 270.29.
View 4 Replies View RelatedI just upgraded to 11.04 from 10.10 (which I had to reinstall after upgrading to 11.04 beta and attempting to install gnome 3 but I digress) and now my monitors are permanantly stuck on clone.When I go into monitor preferences and uncheck same image in all monitors I get a popup error
"The selected configuration for displays could not be appliedrequested position/size for CTRC 148 is outside the allowed limit : position=(1680,0), size=(1680,1050) maximum=(1920,1920)"
What I want to do is set one monitor to 1680x1050 and the other to 1920x1080 but basically it is telling me it needs a resolution higher than this seemingly arbitrary number...in my past adventures with this I was able to change some Xorg.conf file to increase this maximum but I think that was 10.10 and now I cannot find a file that has that setting in it.
I have dual monitors (both 1600x1200) and X is set to span them. I prefer to set my Eclipse window to 3200x1100. However, when I use VNC to connect to my desktop, I'd have to pan around a lot, so I use wmctrl via a script to resize Eclipse (and Chrome, etc.) to better fit my smaller VNC viewport.
When I return to my dual-monitor desktop, I want to resize/move my windows again. But wmctrl does not work correctly. If I do
Code:
(from a script), then instead of putting the window at 0,0 and width 3200, the window appears on the second monitor (i.e. at 1600,0) with width 1600. So I must manually resize it which is more difficult.
Am I using wmctrl correctly? Is it not wmctrl's problem but my window manager? I'm using compiz in Ubuntu 10.10.
I am using Ubuntu 11.04 - the Natty Narwhal 64-bit and I am using the Nvidia Xserver version 173.14.30 and it never has any problems when I am in single monitor mode but when I turn on twinview mode like this----
and click apply the new monitor first shows up black and when I move my mouse over the monitor stuff starts showing up and I am able to click ok to keep my settings
when I click ok the screens freeze. everything else works; I can move the mouse around and if I am playing music it still plays but if I click on any button nothing happens and nothing happens when I use the keyboard either. I would really like to be able to use both my monitors
So I'm using Lenny, trying to get dual monitors set up. I'm not sure on the correct steps, but have done some googlin' and wasn't finding what i was looking for. (could be that i just missed it)
lspci:
01:00.0 VGA compatible controller: ATI Technologies Inc RV516 [Radeon X1300/X1550 Series]
01:00.1 Display controller: ATI Technologies Inc RV516 [Radeon X1300 Pro] (Secondary)
