I have just started with Slackware and I have a problem with my wifi. I don't know if I should make more changes to any archive but when I try to start my wifi it doesn't work at all. What I should do? take into consideration that I come from Ubunut, where everything is done beforehand.
View 6 Replies
I have been trying to get my laptop to share its wireless connection to my older, wireless-less, computers through its ethernet port. So far, I have not been able to make it work. As far as I know, what I am trying to do is called network bridging. The method I have been trying so far is to run these commands as root:
Code:
ifconfig wlan0 -promisc
brctl addbr br0
brctl addif br0 wlan0
brctl addif br0 eth0
ifconfig br0 up
Each time I do this, the system running as a bridge loses connection, and the system being bridged to never gets a connection. My hardware is:
Code:
08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)02:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
I've been trying to install the linux driver for my wireless car which is an 'Intel wifi link 4965'. I've followed the literature that Intel provide but I keep running into errors.
(I downloaded the driver from[intellinuxwireless.org/?n=downloads)
My Lenovo laptop has an Intel Pro 4965 Wifi adapter,here is the "lspci" detection:
03:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
So installed the needed "firmware-iwlwifi" kernel module, which is a correct kernel module for this adapter.
Then "modprobe -a iwlwifi"........no complaints !
However,
#iwconfig wlan0
wlan0 No such device
and
# lsmod |grep iwlwifi
iwlwifi 87219 0
cfg80211 350041 4 iwl4965,iwlwifi,iwlegacy,mac80211
The wired ethernet is working fine
ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:1e:37:82:ac:72
inet addr:192.168.1.16 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::21e:37ff:fe82:ac72/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[Code] ....
when I go to "Preferences" "Network Connection" ' "Add" "WI-FI" "Create" "Device MAC Address " box is empty.......no Wi-Fi adapter detected !!!
After wading through all of the bug reports filed regarding the Intel 4965 AG wireless adapter, trying various suggestions and not finding any solutions to my problem, I've finally decided to scrap the idea of actually being able to get my Toshiba laptop to connect reliably to my wireless network with Ubuntu 9.10. This wireless adapter worked absolutely flawlessly with 8.04 Hardy. I took the plunge once again this week and thought I'd try again to get 9.10 working on my laptop but it's a no go with the Intel wireless adapter (same problem with 9.04, it just doesn't work). You would think with newer versions of drivers and kernels that the same hardware that worked in a previous version, would continue working with newer versions.
Anyway, enough of my frustrated ranting... I need to find a replacement wireless adapter for my laptop that WORKS FLAWLESSLY with 9.10. When I say flawlessly, I mean you plug it in, boot up the laptop and it works all the time, every time. No fooling around with drivers etc... Either a PCMCIA or a USB wireless adapter that is currently available for purchase. I've waded through the sticky on the forum about which adapters are supposed to work, but I'm really hoping that someone here is using either a PCMCIA card or USB card and could please point me in the right direction. It's kind of funny, I purchase my Toshiba laptop because I read reviews here in the forum about how great it worked with Ubuntu 8.04. How all the hardware was recognized and worked out of the box. It did... with 8.04. Everything still works with 9.10 except the wireless.
kernel-2.6.32.10-90.fc12 seems to break 802.11n with my intel 4965 chip on my thinkpad t61p. Anyone else seeing the same thing? iwconfig shows extremely low bit rate. dmesg doesn't show anything at all unusual.
View 10 Replies View Relatedwhat is really a rant disguised as a question, but does anyone have this combination working? My NetGear router shows the connection as allowed from the MAC address in the router logs, And I can see the network I want to join in the list of visible networks from the laptop, but dmesg shows Ubuntu disconnecting with
WPA-PSK [TKIP] only:
wlan0: disassociating by local choice (reason=15)
WPA-PSK [TKIP] + WPA2-PSK [AES]
wlan0: disassociating by local choice (reason=3)
I'm sure there is a simple explantion that has been sufficiently buried somewhere but after several hours of googling and searching the forums here I can't find it. Anyone want to help out an old man RTFM?
I'm getting really disappointed here lately - things are getting worse, not better. In my case in particular I have this laptop with supposedly open and supported drivers and they don't work, however, the exact same distributuon on a Dell D830 with a broadcom NIC does. under 8.10 and 9.04 this worked out the box - just logged in, gave the PSK and away we went. I can't see the attachment I just uploaded so to include the information requested in the "how to get help" post, I'll put it all here inline...
Code:
Machine Brand and Model (PC/Laptop): Lenovo R61
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c)
00:01.0 PCI bridge: Intel Corporation Mobile PM965/GM965/GL960 PCI Express Root Port (rev 0c)
00:19.0 Ethernet controller: Intel Corporation 82566MM Gigabit Network Connection (rev 03)
00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 03)
00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 03)
[Code]...
I have been getting from my wireless adapter. This has been going on for quite some time but only now am I able to see a pattern. The behavior seems to be the following: Start up, connects to network and work fine until I suspend my machine. On wake up, it works again but after a seemingly random amount of time the connection is lost and I can no longer find any networks. Attached is dmesg output after startup and connecting to a wireless network (dmesgAfterConecting.txt) and the same after the connection has been lost (dmesgAfterConnectLost.txt). I get this error which seems important:
[Code].....
Installed Ubuntu 10.04 on my Sony UX280p with Intel 4965 wireless. Ubuntu detects the card without issues (as far as I can tell). I can see all access points in my area and select my access point and pair with it. I get a DHCP address from the AP (if ifconfig is to be believed) and iwconfig shows the ESSID of my AP but I can't ping the AP or any other computer on the network, nor can I ping the sony from any other computer on my network. Last year I had installed 9.04 on this computer and wifi worked out of the box without any issues.
View 2 Replies View Relatedim new to Centos and need my wifi card working .i tried the help but apparently yum cannot find any packages and neither are the packages available on the site listed
View 2 Replies View RelatedI am new to Ubuntu and I have problem with wireless connection. I could not find any wireless connection at all. I am now using wired connection. Sony Vaio SZ series, Intel Corporation PRO/Wireless 4965 AG or AGN My software details are:
$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
[code]....
A few months back, my Lenovo IdeaPad Y510 stopped connecting to my wireless network after coming out of Suspend (it had worked fine previously). Wireless networking is simply disabled, and I have to reboot in order to get it back. I tried upgrading my OS from Intrepid all the way to Lucid, but the problem persisted. I also tried changing my 00sleep_module as suggested in this thread, but to no avail.
[Code]...
My wireless worked out of the box for the past few months. When I was running low on battery recently, I put the laptop to sleep. When I woke it up, there was a black screen with a flashing underscore. I pressed a bunch of buttons but nothing happened. Then suddenly it said something about a wireless hardware error and I did a hard reset by holding down the power button. When I turned the computer back on, wireless was greyed out. There's no hardware switch to enable and disable wireless and the software switch had no effect. I tried echoing into the 'state' of the adapter but it didn't let me. When I tried sudo ifconfig wlan0 up it gave me the following error:
Code:
SIOCSIFFLAGS: Unknown error 132
lspci:
[code]....
I'm a Linux newbie. Used to use Ubuntu, but I switched to Slackware because I want to learn how Linux works better.
On my Samsung qx410 laptop, I can't connect to the internet. I went to the System Settings -> Network Settings and all the tabs there, but it wouldn't detect any connection, wireless nor wired.
I noticed that the kernel of Slackware 13.1 is out of date, so I tried compiling a newer one, but I couldn't get that to work.
I tried downloading this file: iwlwifi-6050-ucode-41.28.5.1.tgz but even after reading the readme, I had no clue how to go about installing it or even whether it was the right thing to install in the first place.
How can I get my internet working?
I've reinstalled Slackware 4 times today because of things I've messed up along my way, after upgrading the linux kernel I've had issues with getting back to desktop, so I'm on a clean slate right now with the exception of installing wicd. I need help since wireless is not working.. My wireless worked fine out of the box with Ubuntu,I don't understand why it is not working now... Using Slackware 13.1, Kernel 2.6.33.4
Code:
bash-4.1# ifconfig wlan0 up
SIOCSIFFLAGS: No such file or directory
[code]....
I am running openSUSE 11.3 updated with all the latest patches and I cannot connect to my wireless router. I am running Linux Mint 10 on the same type of notebook HP Compaq 6910p and it worked right after the install. If I take off the security WPA & WPA2 Personal I can connect. lspci -v | less shows this for my wireless card.
10:00.0 Network controller: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection (rev 61)
Subsystem: Intel Corporation Device 1000
Flags: bus master, fast devsel, latency 0, IRQ 29
Memory at e4000000 (64-bit, non-prefetchable) [size=8K]
[code]....
I am using the same settings for both notebooks just can't figure out why openSUSE 11.3 won't connect. I get the prompt to key in my password, I've even checked the box to show password to make sure I was keying it in correctly. Everything was good but it just goes right back to the password prompt after it fails trying to connect.
I upgraded to OpenSuse 11.2 and just about the only thing that doesn't work is my wireless internet. From my research, I should be using the iwl4965 or iwlwifi driver; however my system seems to be running iwlagn. I have no idea how to switch it as neither of the correct drivers can be found in my yast, and I've failed to find any information about this on the Intel® Wireless WiFi Link drivers for Linux* website.
View 9 Replies View Relatedtrying to connect wireless on wlan0 intel pro wireless 4965 AG or AGN
View 1 Replies View RelatedI have only had a few weeks worth of experience with linux, so I'm probably considered a newbie at this but I felt like giving it a shot. I just configured my new Toshiba Satellite A505-S6969 to jaunty. Most of the transition is going well but I'm stuck with a few issues, one of which is getting my wifi to work. Right now I'm working off of an ethernet cable.spci returns
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port
[code]...
Installed ubuntu 9.10 dual boot with win7 yesterday. Everything working but Wifi. Wifi works fine with Win7. No Wifi in Ubuntu. Very confused. I have info from the wifi trouble ticket post.There does not seem to be a driver for this card anywhere.
lawrence@lawrence-laptop:~$ lspci
00:00.0 Host bridge: Intel Corporation X58 I/O Hub to ESI Port (rev 13)
00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13)
[code]....
I am running (K)Ubuntu Lucid 10.04 64bit on a Dell Latitude E6400, WiFi Card Intel 5100. Never had any problems with networking. Up to about 2 weeks ago. I do realize there have been quite a few posts with this network adaptor, but non really described the problem I have here.
What happens is that suddenly the WiFi LED on the computer stops blinking, the WiFi connection gets disrupted, and the device is not recognized anymore when checking ifconfig. Only cold restarting the machine helps then... it will work for a while (between 1 and 20 minutes) and then crash again.
On Windows 7 the card works perfectly fine. With Ubuntu 11.04 in Live CD mode I have the same effects (connection crashes after a while). Also tried booting an older kernel, no success.
My exact hardware:
Code:
I notived the following problems in /var/log/kern.log
Code:
i tried following the readme file included in the driver of the usb network adapter but seems its not exact.
any ideas on how i can configure it manually? KDE does not detect any wifi device. .(of course since no driver is installed yet).
i used my desktop (win***)with DSL connection and installed the driver of the usb net adapter.. made it as the access point. . so my laptop detects the desktop as wifi spot.
I'm trying to setup CentOS 5.4 x86_64 on a new machine but am running into problems. The machine is: CPU: Intel Core i7-860 RAM: 4GiB DDR3 Motherboard: Intel DQ57TM When booting from the disc, I get to the initial splash screen but almost immediately after that, I get a kernel panic.
None of the lines leading up to it mean much to me so I'm not sure what to copy here but the last line says: <0>Kernel panic - not syncing: Fatal exception
I have just been forced into upgrading my mother board and cpu so now own a x86 cpu and was thinking i would give the x86_64 Slackware a try. I realize that i need to do a reinstall but can i save my /home partition? Will that save my settings or am i asking for problems? I assume i can just drop all of my config files into the new install as well.
View 4 Replies View RelatedWhere I could get Intel 3945abg wifi drivers for ubuntu?P.S. Sorry for wrong forum, but I can't post in networking forum.
View 3 Replies View RelatedI have backtrack 4 on vmware player.i have intel (R) wifi 5100 agn wireless card and when i type airmon-ng there is nothing shown on interface..and i have been told i need kernel rebuild..i have kernel 2.6.30.9 so how can rebuild it?
View 10 Replies View RelatedI used the fbreader.SlackBuild in a 64bit system to create a package and I got some libraries installed under /usr/lib instead of /usr/lib64. FBReader seems to work fine though, so I'm not sure this is a problem. I guess it could be if some other app looks for those libraries. Just thought I should report it anyway.
I used UI=gtk if it matters.
I'm an new to Slackware.I want to ask how to run 32bit program on x86_64.
My Slackware is 13.1 x86_64.
I am having difficulties to connect MX 5500 Keyboard and mouse through the Bluetooth dongle.
I am running on the latest kernel, 2.6.32.7, from Slackware64 current.
I have done some searches and followed the procedures below:
Quote:
Quote:
Quote:
Quote:
Restart my system.
Plug in the dongle with red button pressed.
Quote:
Press red button on the mouse back and issue the following command
Quote:
Can't get device information: Function not implemented
Same thing happened when I tried to connect keyboard.
What should I do to connect keyboard and mouse?
The sc spreadsheet app doesn't really work in 64bits. It launches but you're unable to do anything with it, it's not possible to enter any values in the cells or do anything else. It works fine in 32bit though.
To make it work properly in 64bits, you can use this patch, borrowed from debian: http://salix.enialis.net/x86_64/13.1...changes-7.16-3
And there is also this patch to make DESTDIR work properly with the Makefile: http://salix.enialis.net/x86_64/13.1...-destdir.patch
