I was playing around with some files in Slackware and decided to do something stupid for the sake of experimentation. I wouldn't say I screwed something up because I did it intentionally to see what would happen (that's how you learn, right?), but I disabled my login tool. I need to access to the....
View 2 RepliesI have just reinstalled slackware on my old p4 3.2 box clean install formatted hard drive no other packages installed.is there something seriously changed from slack 10 to slack 13.1 ?? or do i suffer from C.R.S ( cant remember s***)
View 5 Replies View Relatedis there a Linux utility that will let me access the Wubi filesystem in a live cd?
View 3 Replies View Relatedi'm having some problems booting ubuntu 9.10 and i just want to backup my files and install it all over again.I want to access my old files from the ubuntu Live CD, because no kernel is working.Is there a way?. Just in case, i don't have partitions, so i don't have a 'home' one (but i'm going to
View 5 Replies View RelatedI'm receiving the following error message when running LILO under SystemRescueCD after installing Slackware 12.2 (the slackware setup hung when installing LILO so I am trying to install manually - I have re-run setup, including formatting all drives again):FATAL: Trying to map files from unnamed device 0x0010 (NFS/Raid mirror down?)Let me know if any more information is necessary and thank you in advance for any help you can provide.
View 7 Replies View RelatedI'm having some problems booting ubuntu 9.10 and I just want to backup my files and install it all over again. I want to access my old files from the ubuntu Live CD, because no kernel is working. Is there a way?. Just in case, I don't have partitions, so I don't have a 'home' one (but I'm going to).
View 1 Replies View RelatedUbuntu 10.10 has crashed and I'm resigned to a re-install, however is there any way to recover or access my files via the CD, live, during install or after ?
View 3 Replies View RelatedI am trying to install Fedora 10 on an old P3 Inspiron 5000. When I boot from the Live cd the screen is split into three sections and is hard to navigate. I am able to edit the /etc/X11/xorg.conf file and log out and log back in to proceed with the installation. The problem is when I finish the installation and reboot to the new OS it boots to the triple section mode again because my xorg.conf is not edited. To do any commands in Fedora I need to get through a brief user setup in which I cannot navigate through until I can see the screen better. Is there a way to boot to a graphical type safe mode so I can see the whole screen to finish the installation?
How can I access folders from the live cd to edit the installed files? This way I can edit the xorg.conf file before booting and all would be legible.
I've install Slackware 13.1 and i cannot shutdown my PC. The shut down process stop while trying to run PCMCIA module.
This is the first time that happens.
From Hardware point of view , i didn't do anything at all (if that helps).
Anyone upgraded php to 5.3.x in slack 13.1?
Could you please share the slackbuild?
I installed a slack 13.7 on an old laptop. KDE was set as default desktop. then I login and run startx and I saw KDE first screen display. after that I saw blank screen with a mouse on it. Then it stayed there and it seems try read some in my harddisk since the persistent harddisk light.
View 3 Replies View RelatedWhen I try to put slackware to sleep or have it hibernate the system simply sits with a black screen. Normally it would do this for a short period of time immediately before the actual sleep state (screen powered off, croissant light on) is entered, but currently it does it indefinitely. My sleep USED to work just fine, it broke after some unclean shutdown or another, basically I just want to know what I can try resetting to try to get it back to normal.
Slackware64 13.1, running on thinkpad X61.
EDIT: Of course the second I make the post I think of trying to sleep/hibernate from the command line instead of through X/GDM (Gnome SlackBuild). That works.
I have some doubts about the official Pat's upgrading procedure. In the UPGRADE.TXT file, one of the stepts says:
Code:
upgradepkg --install-new *.t?z What does --install-new mean? Pkgs I have no installed on my 13.1 will be installed on the 13.37 upgrade? For example, I did not installed KDE on 13.1. Will be installed when upgrade? - What about third party pkgs? Slacky, SlackBuilds.org, compiled by myself. Should I remove them before upgrading slack?
Does it mean that a 64 bit version is not multi-core?
View 11 Replies View Relatedi am not able to access my pen drive on slack ware
View 3 Replies View RelatedI have a XPS 1530 and when I type
lsusb
[code]
It seems to be that the camera is recognized by the OS but it is not working when I try to use it in skype or in EVO.
Has anyone here succeeded in getting armed slack running on a consumer kirkwood device .ie. one without serial console? I have a tonido plug that I want to liberate. By default the plug boots first from the external usb, so I would only need to set up / on the first partition. I would be very interested to know if someone had managed to install slack to the internal nand without bricking it.
View 9 Replies View RelatedI downloaded Qt SDK file (530 MB and file is ok ) qt-sdk-linux-x86-opensource-2010.05.1.bin, I type in console ( slackware ) like in manual for installation at site
Quote:
chmod u+x qt-sdk-linux-x86-opensource-2010.05.1.bin
but when I type second command for installation
Quote:
./qt-sdk-linux-x86-opensource-2010.05.1.bin
I get error message
Quote: bash: ./qt-sdk-linux-x86_64-opensource-2010.05.1.bin: cannot execute binary file How to install ?
I compiled it from source, i installed it via slackbuild but it didn't work. When i go imlib-config --version it shows me the old one, and when i try to install giblib it tells me that imlib2 is not installed. I watched the output from the installing of imlib2 and i realized something's wrong: there are several suspicious warnings :
[Code]...
I don't know if i'm doing anything wrong but, to change the bootsplash picture its just change the slack.bmp in lilo.conf and reboot?
View 6 Replies View Relatedmy problem, I have Slackware 13 dual booted with vista on a dell 1545 2 ghz 2gig ram. to these forums I have gotten everything working except my creative zen vision M 30g. I have tried alll the suggestions posted here and other places on the net. Here is my output from lsusb.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 002: ID 046d:c018 Logitech, Inc. Optical Wheel Mouse
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[Code]...
any way i can transfer files back and forth to this would be great since it does not work in vista either. and I am pretty sure 99.9% that I have all the libmtp, libnjb, and whatever other libs are needed installed but in gnomad it says no devices found on USB hub. I hope this is enough info and someone out there has the trick or maybe I am missing something obvious.
i installed compiz fusion on my slack 13.1 i installed in the good order all the packages nevetheless when i try to use DBUS in command line i don't have any response from compiz
here is one example
Code:
dbus-send --type=method_call --dest=org.freedesktop.compiz /org/freedesktop/compiz/switcher/allscreens/next org.freedesktop.compiz.activate string:'root' int32:`xwininfo -root | grep id: | awk '{ print $4 }'`but no reaction .what can i check to have a functionnal DBUS ?
I have downloaded the packages from Slackbulids and installed also the required packages from slacky.eu but still it says that probably pyqt is not installed. I have installet latest Sip and latest pyqt ver 4.
View 1 Replies View Relatedi know that there is a reset button on the back but after reset i dont know what to do with it. right now i m using pppoe connection which only works in windows and bt4 and i want to make it run in slack 'cause now slack is my main os(66hr since i switched to it :0) so i want to configure the modem in a way that i work in slack. and i m dumb about PPP/TCIP/DHCP and btw i like "the" slack
View 7 Replies View RelatedI like GNOME. So, I want to install gnome 3 as my desktop environment.
View 9 Replies View RelatedI installed slackware on my laptop last night, :-) very happy. Can't wait to learn more about linux and even computers in general. I've already learnt heaps since entering the alternative operating system world. Anyways, i've got xfce up and running with slack now, created a new user 4 my self. And now i'd like to get some updates and stuff, but i need to use my mobile broadband. It's a telsta dongle If that changes the circumstances. How would i go about setting this up?
View 2 Replies View RelatedI am trying to setup a PXE booting environment in my network and I almost got it to work... Only it does not quite work yet... Basically, I want my laptop or any other machines to boot from my network. I followed the instructions from AlienBob to do so. I setup my laptop to boot from the NIC, it automatically gets an IP from the DHCP server (pfSense);
I setup my gateway/DHCP server (pfSense) as is: -The IP address from the network boot server: 192.168.0.101 (the server where my slackware mirror and all tftp boot files are) -The filename used for network booting: /mnt/it-maintenance/tftpboot/slackware-13.1/pxelinux.0 (the absolute address of pxelinux.0 in my server)
I setup the network boot server (running slack 13.1) as is: -uncommented the line in inetd.conf to have:
Code:
tftp dgram udp wait root /usr/sbin/in.tftpd in.tftpd -s /tftpboot -r blksize
-added a NFS share to /etc/exports to have:
Code:
/mnt/it-maintenance/operating-systems/slackware-13.1
192.168.0.106(ro,sync,insecure,all_squash)
[Code]...
I am having problems getting Seamonkey 2 and 2.0.0.1 to run on Slackware 12.2. I have tried the packages for 12.2 in patches/packages/ and the package from the seamonkey website, both with identical results. Seamonkey appears to start, and does appear in the process list, however no windows appear and it uses little memory and no CPU cycles. No messages appear in the console if I start it from there. I have to kill the processes (seamonkey , run-mozilla and seamonkey-bin). I have tried removing my Seamonkey profile, with the same results.
If I try to build the slackbuild I get this error:
Code:
checking for cairo >= 1.8.8 freetype2 fontconfig... Requested 'cairo >= 1.8.8' but version of cairo is 1.6.4
configure: error: Library requirements (cairo >= 1.8.8 freetype2 fontconfig) not met; consider adjusting the PKG_CONFIG_PATH environment variable if your libraries are in a nonstandard prefix so pkg-config can find them.
configure: error: ./configure failed for mozilla
/usr/bin/gmake -C mozilla default
gmake[1]: Entering directory `/tmp/comm-1.9.1/mozilla'
gmake[1]: *** No rule to make target `default'. Stop.
gmake[1]: Leaving directory `/tmp/comm-1.9.1/mozilla'
make: *** [default] Error 2
The version of Cairo I am running is the standard Slackware 12.2 version cairo-1.6.4-i486-1.tgz, which to my knowledge, has never been updated (there is nothing in /patches/packages for it, anyway).
I have myself a perfectly working slackware 13.1 64 on my pc (well, tbh I gotta solve some ati and kde compose issues),BUTI can get no joy when trying to make it work in friend's pc.The slackware 13.1 32 install runs ok. I can even log in and run a init 4 session on kde.But with no apparent reason hard crashes (completely frozen system) hit the system aleatory (never last more than 5 minutes)
View 14 Replies View Relatedso, I was wonderin just how many distros are slack 13 based?I know Absolute and SalixOS is.I tried installing Vector Lite (12.1) and no mouse and other big issues?was gonna try Zenwalk, but heard its Dead?So, are there any other 13-based distro's?
View 14 Replies View Related