We have configured software based RAID5 with LVM on our RHEL5 servers. Please let us know if its good to configure software RAID on live environment servers. What can be the disadvantages of software RAID against hardware RAID.
View 2 RepliesI have a new DL180 G6 server with 4 x 500Gb HDD's. I have configured this into a 1+0 raid array and the configuration utility reports 1Tb space as expected. When I boot off of the RHEL 5 DVD the 4 HDD's are there, not my array?
View 8 Replies View RelatedTrying to install RHEL5-AS 64bit onto HP DL320 G6, with RAID being a mirrored array on the Smart Array B110i SATA controller. The RAID is configured in the BIOS and seems fine.
When I install RedHat, I have to use 'linux dd' to use the HP provided driver (http://h20000.www2.hp.com/bizsupport...5&mode=4&idx=0) and that works fine during the installer, the GUI during the install sees the RAID just fine, it sees one volume, calling it the HP Volume. However, when the system boots after the install, the RAID is gone, and it's now seeing two drives, /sda and /sdb:
[Code]...
Could any RAID gurus kindly assist me on the following RAID-5 issue?I have an mdadm-created RAID5 array consisting of 4 discs. One of the discs was dropping out, so I decided to replace it. Somehow, this went terribly wrong and I succeeded in marking two of the drives as faulty, and the re-adding them as spare.
Now the array is (logically) no longer able to start:
mdadm: Not enough devices to start the array.Degraded and can't create RAID ,auto stop RAID [md1]
I was able to examine the disks though:
Code:
root@127.0.0.1:/etc# mdadm --examine /dev/sdb2
/dev/sdb2:
Magic : a92b4efc
Version : 00.90.00
code....
Code:
mdadm --create --assume-clean --level=5 --raid-devices=4 /dev/sda2 /dev/sdb2 /dev/sdc2 /dev/sdd2
As I don't want to ruin the maybe small chance I have left to rescue my data, I would like to hear the input of this wise community.
I've been running my dedicated server on Ubuntu 10.04 for 300 days non-stop so far (touch wood). I'm planning to purchase a dedicated server to host many large sites. The specs are Sandybridge Xeon with 16 bay x 2TB storage using RAID5 (Adaptec RAID 51645).I don't have experience with RAID, but I read that ext4 can only support filesystem up to 16TB, my plan for the system is to have 32TB of storage. How can I make Ubuntu run this configuration?
Also, can Ubuntu 10.04 recognize the Adaptec card? Going through Adaptec website there is no mention of drivers for Ubuntu (although many other distros are available).
Quote:
EFI GUID Partition support works on both 32bit and 64bit platforms. You must include GPT support in kernel in order to use GPT. If you don't include GPT support in Linux kernel, after rebooting the server, the file system will no longer be mountable or the GPT table will get corrupted. By default Redhat Enterprise Linux / CentOS comes with GPT kernel support. However, *******if you are using Debian or Ubuntu Linux,******** you need to recompile the kernel. Set CONFIG_EFI_PARTITION to y to compile this feature.
Is this true? Ubuntu has no GPT support native to the server install? Never compiled a kernel. Is that of itself going to be a mind bender? How much doo doo am I going to get into if I haven't done it a few times? Trust me when I tell you its no thrill formatting and reformatting a 8tb raid drive or the individual disks if it screws up. Been on that ride way too long already. Need things to go smoothly. This is not a play toy server, but will be used in a business.
I am rebuilding two microsystems servers and I need some advice to make my dreams come true.I want to setup the servers in a RAID configuration and want to install a GUI Linux application to manage a file server, manage a subnet, and host a Moodle on my subnet.I am planning to use Asus eee netbooks running Linux as my client computers. I basically need to be able to get my kids on the web and be able to have them use some open source office suite tools. No major crunching. I'll have two Macs for that.
View 3 Replies View RelatedI have had no problem installing Fedora OS on any of my Dell servers prior to this post. Anyway, I wouldn't call this a problem but recently, we bought another DELL server with Quad Core, 4GB, etc... AND this model has 2 swappable SAS Harddrives.
I wouldn't call myself an expert but then again I am not a newbie too. However, I have never setup any RAID before and now I am forced to setup RAID1 on this server. So, in a way, I am a newbie in setting up RAID
Would someone please point me in the right direction as I have no idea what I am supposed to do to setup the RAID. FYI, I will be installing Fedora 10 64bit on this server. I would appreciate if you can start from the very beginning, ie. partitioning, formatting the harddrives during OS installation, etc..
Ran 'do-release-upgrade -d'on my server running Hardy.No problems during the upgrade.Rebooted after the upgrade completed, and I was presented with the new plymouth screen. This sucks for servers.It sat there displaying the logo for ~5 minutes.Hit CTRL+ALT+F1 through F8 and didn't see anything on the virtual consoles.Finally figured out that I had to hit ESC on the plymouth screen to actually see what was going on.It said /dev/sdi1 had problems along with /dev/md0.It sat there forever with no fsck status and no HDD lights blinking.
SysRq+REISUB and tweaked the boot parameter to remove 'quiet splash' and appended 'S' for single-user mode.Got the attached screenshot.The box has been sitting like this for ~15 minutes.Not entirely sure what to report a bug against at the moment. Plus the somewhat-new requirement of running 'ubuntu-bug' is pretty retarded in this situation. (Yeah, I know I can add some string to the URL to get around it.Why is it such a pain in the *** to report a bug?)I'm going to do some more digging to try and find out what is dying during boot.The new boot process is a bit of a mystery to me still, so if anyone has pointers or any devs want more detailed information,
I'm having a great deal of time getting Lucid Server up and running on my Compaq Proliant ML330 G2. I've put a thread up in installing and upgrading, but people there don't seem to have any ideas about my problem. Since I figured there would be a higher concentration of server users here,
I've got a Proliant ML330 G2, 2 1.4 GHz PIV's
A dvd and CD drive on IDE1 (I'll explain why in a moment
A 65 gb hdd on IDE2
and four 40gb hdd's on hardware ide raid.
I've tried everything, but I can't get the sucker to boot. Installing to the raid array doesn't work. Some array setups won't partition, and others aren't even recognized as arrays. I've tried disabling the raid array and installing to the IDE hdd (my original intention) but I just get bad system disk errors. It would be exceptionally helpful if anyone has one of these boxes, or has worked on one, but I'm willing to take advice from any direction at this point.
We have been using Ubuntu Server at our department since several months now. It hosts a website, e-mail and nfs(only intra).
It was set-up as RAID 0 with two 1TB Hard drives but I want to change it to RAID 1 for fault tolerance. Is it possible to change existing RAID level? If yes can someone point me to the proper place?
I tried "mdadm" documentation and level set option is available but no explanation available that whether it is only while creating the array or it can change the level too.
I have a total of 4 hdd's, 500gb 7.2rpm that I would like mirrored using raid 10. As you can see from the image, ubuntu 9.10 server isn't recognizing the full 2tb's. In fact, I'm not even sure about the configuration as I was thinking the HDD's would come up as four 500gb hdds. Instead I have the configuration above set and ready for Ubuntu to be installed on.
1. Is this typical of a server pre-configured from Dell(perc6 raid controller.
2.Why is ubuntu not recognizing the full capacity of the drives especially when it's a server install?
I have a client with a pair of Supermicro 6025B-T servers that he wants to have Ubuntu 10.10 64bit Server running on for VM/Cloud experimenting. He needs these to be set up RAID 10. I can go into the Adaptec utility and make the array and make it bootable and get to the point in the installer where it asks me if I want to use the SATA array - then it gets to the partitioning screen and the array is nowhere to be found.
View 1 Replies View RelatedHow long does hardware Raid card (raid 1, 2 drives)take to mirror a 1 TB drive (500gb used)?Is there a general rule of thumb for this?4 hours? 12 hours? 24 hours?
View 1 Replies View RelatedI am trying to connect a RAID Box to the server via LSI 8880EM2 RAID controller.The raid box is FUjitsu Externus DX60 with raid 1 configured.The server is Fujitsu Primergy SX300 S5 with LSI 8880EM2 RAID card.The external raid box is being recognised by the raid controllers bios.
The server runs CentOS 5.5 64bit. I have installed the megaraid_sas driver from LSI website and MegaCLI utility but CentOS still fails to see the box.MegaCLI utility, when launched from CentOS, recognises the raid box, CentOS does not(no mapping being created in /dev).
I have also tried to create a logical RAID0 HDD on one physical HDD(as seen by MegaCLI) with MegaCLI utility in CentOS.The result was success and the new logical drive could have been used, but when restarting the server, the controllers' bios fails with an error (not surprised(one logical RAID0 on one physical HDD)) and configuration is being erased.
Has anyone tried connecting 8880EM2 controller to a raid box with raid configured on the box, running it all under CentOS and what were the results.
We've recently created 3 new RHEL5 servers and added them to the existing workgroup which all our other 7 RHEL4 servers run on. (All servers have been added into DNS). We seem to be having a few issues pinging 3 of the RHEL5 servers.
Below is an example of our ping tests:
WinsSrv1: Can ping all but RHELSrv1
WinsSrv2: Can ping all REHL Servers
WinsSrv3: Can ping all but RHELSrv2
WinsSrv4: Can ping all but RHELSrv2 & RHELSrv4
WinsSrv5: Can ping all RHEL Servers
There is no real pattern as to what server we can ping. We can ping all RHEL4 servers with no issues. All REHL5 servers can ping themselves with no issues.
I have one scsi storage array, JetStor SATA 416S,split into 2 halves. each is RAID5 12TB. Is it possible to dedicate each half to a different rhel5 server. I have "lsi22320-r" ultra230 dual channel scsi adapter in each server.
The first server sees the 2 halfs however the second server doesn't on the first server:
I have 2 ethernet cards but when I look at the Network configuration in "Hardware Tab" I have another acx wireless network. How to delete that because In my system Idon't have wireless card..probably installed before but want delete it now.
[code]...
then windows can ping server and resolve ip address and browsing Internet but can't ping [URL]... result is Request time out. ICMP already enabled in iptables.
I am looking to convert a raid 1 server I have to raid 10. It is using software raid, currently I have 3 drives in raid 1. Is it possible to boot into centos rescue, stop the raid 1 array. Then create the raid 10 with 4 drives, 3 of which still has the raid 1 metadata, will mdadm be able to figure it out and resync properly keeping my data? or is there a better way to do it?
View 2 Replies View RelatedI have a box that doesn't have a Raid controller or a software raid running currently. I would like to make it a RAID 1. Since it seems there isn't any IDE RAID controllers hardly around, I have another HD that is the exact model as the drive currently in the box running CentOS. Can I some how add the second drive and get the box to mirror from here own out? The box gets really hot and I want to be ready for a HD failure.
View 3 Replies View RelatedI'm developing simple transaction switch using java socket programming and running operating system RHEL5.4 . Now it is completely done and working fine. So I have written the simple shell script to run it on background.
[Code]...
how can we achive more than 8TB size for one LUN.?I am getting following error..
[root@storage ~]# mke2fs -j /dev/VG01/data
mke2fs 1.39 (29-May-2006)
mke2fs: Filesystem too large. No more than 2**31-1 blocks
(8TB using a blocksize of 4k) are currently supported.
I want to implement CBQ in my RHEL5 server so that i can manage my BW.
View 4 Replies View RelatedI have rhel5 running ok and windows7 running ok, and currently access both via grub (both os are on separate disks) I want to be able to switch between both without rebooting. xen is installed and working but I cannot configure windows to run as a guest as xen wants an iso or img file.
View 1 Replies View Relatedi wnt to know how to configure nat server in rhel 5 i have net on eth0 so hw can i share net on my lan through nat server
View 3 Replies View RelatedI am configuring apche on rhel5, I got default page successfully, and virtual page too, when I keep only one file index.html in virtual folder it goes well, that file opens correctly, but when I keep other html files except index.html server shows default page again.
View 2 Replies View Relatedhow to configure vsftp in my rhel5 server.
View 2 Replies View RelatedI installed RHEL 5.5 with Postfix & openldap. POSTFIX version-2.3.3 openldap-server-2.3.43-12.el5 How to combine ldap with postfix for authentication? How to compile postfix with LDAP and where is the source
View 1 Replies View RelatedI wonder if someone can shade alight on this problem,I have active subscription for rhel4 ES and trying to do a fresh install of rhel5,I was able to download rhel5.3 DVD image from redhat site,burnt it to a DVD but is not booting,i have so far tried on 2 different DVDs but both have failed. I have even downloaded and burnt 1 CD ISO image burnt it still failed.BIOS level is set to cd device first so no problem there,it works!
View 5 Replies View RelatedI'm trying to get RHEL5.3 booting on an IBM Blade off a SAN disk, but it refuses.Our storage is presented on LUN 1 as due to the IBM XIV SAN, we cannot use LUN 0 when presenting volumes. We believe that when the installer tries to configure the boot LUN, it expects to see it on LUN 0 but we can't use that. This leads to a problem where after installed Red Hat, it asks me to remove the CD and reboot, but doesn't load anything other than a cursor blinking at me on the monitor.I currently can't change the LUN ID on the SAN, so I've been trying to amend things to get it to work with no joy.
View 3 Replies View Related