On my triple-boot-system with XP,Suse 11.3 and Ubuntu I can`t access the web with all the OS.In spring,I used an USB-stick to connect,and got it only work to connect with WindwsXP, not with Suse and Ubuntu.The stick was identified by Suse as modem and storage-capacity as well.Now,running a DSL-connection,only Suse and Ubu are connectable,but not the XP!
View 3 Repliesim on node1 when i type the command ssh node2@ip the terminal hangs up a bit then an error message stating that connection timeout but here is a thing: i cant ping to node2
but i can terminate the ping manually using ctrl+c when i terminate the ping usual message appears stating 10 packets transmitted, 100% loss
ps: when i go to node3 and ssh to node2 it works fine and also i can ping from node3 to node2 very fine. and the firewalls are down at all nodes -all wired connection over a switch
I can make a connection to the vpn server, the connection starts, but nothing happens! My IP address remains the same as previous! There is nothing added to my Knetworkmanager, I'm a beginner I should use a pcf file for my vpn connection. I use it properly, I'm sure because the connection starts and an icon is added to my panel and remains until I disconnect.
I checked it via ifconfig -a, the last part (which is for vpn) is:
Code:
tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:141.213.169.76 P-t-P:141.213.169.76 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1390 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
I've not found how to configure more than one ip address with network manager.Nor with kde nor with plasmoid network manager.I need several virtual ip addresses for eth0 when the "default" of eth0 is connected i.e. "Connected to Auto eth0" should initialize the virtual interfaces.I have not found no even how to configure the ip address.I think this will be used from ifup config in yast or not?There I have the virtual interfaces but they are not taken from network manager.And last but no least: Is it possible that when using network manager the eth0 is enabled even no user has logged in?
View 4 Replies View RelatedI deleted the firewall files "K09SuSEfirewall2_init", "K01SuSEfirewall2_setup", "S11SuSEfirewall2_setup" and "S01SuSEfirewall2_init" from "/etc/rc.d/rc5.d" in order to disable the firewall when rebooting.
As a consequence all network services are not working. I can't connect to any other machine nor to the internet.
I rebuilt the symbolic files based on the ones for runlevel 3, but still no network services are available.
Any suggestions how to make it work again? I'm using Suse 11.3.
Im new in this world of linux and suse. I have just installed the opensuse 11.2 in a Dell Inspiron 5160. Such laptop has a BCM4306 Wireless LAN controller. When I tried to configure a wlan connection, I found that the firmware was not installed. After looking in different forums, I installed the firmware b43. Now, my wlan card is abled to find the wireless of my router.
I have tried to configure a connection with YAST as well as with Network Manager, but both cases failled. Specifically, when I use Network manager, Im able to see in the applet my connection, how strong is the signal, but I see a yellow symbol (in one forum, such a box is shown with a green symbol).
I have check many time all about the secutity, encryption, and so one and all seems to be correct. But when I open the mozila firefox or the konqueror browser, no chance to surffer in internet. Now Im just a step to become crazy. The drivers are ok, the information about the router and the keys are ok, but in such a way, I am still harmloss.
I installed OpenSuSE 11.3. The only "extra" package I put in after the install was VirtualBox-ose. The firewall is disabled. I gave the machine a static IP address. I can get to the Internet from the machine. I enabled sshd to start on boot with "chkconfig sshd on" and also verified the service is running on the machine. I can ssh user@localhost from the machine as well.
When I try to connect to SSH from another machine, I get a connection refused. I verify that the firewall is down. I also try to get to VNC -- same problem: Connection refused. I ping the machine for fun. If I try to SSH again, it sometimes gives me a logon? I would check the server logs for the connection refused, but I wouldn't know where to look. I started in /var/log/messages, but nothing seemed to jump out there. I also find it strange because I can RDP to a windows guest running under VirtualBox. The Windows guest uses Bridged Network and DHCP.
I also find it interesting that I sometimes type a "ping google.com" from the 11.3 box and it will just hang - no output. Then I open firefox and get to the internet. All of a sudden, ping starts to give output. Could this be a neetwork card issue? A configuration issue? I don't know where to start.
So up until I updated from Opensuse 11.3 to 11.4, I hadn't any issues with my network connection. At least none worth mentioning. Once I installed 11.4, I've had weird issues with varying lengths of connection. Sometimes I can't connect anywhere, sometimes I can only get to the router, sometimes I'm 100%. I'd fiddle with YAST until everything worked. I honestly have no clue whether or not anything I did had any effect.
Enough of the iffy history, here's what's happening now. For the past few weeks up until last night, I have been at 100% connectivity. I never turned off my computer until last night (it just shut itself off, like the cord was unplugged. I dunno what happened, maybe it was my foot, maybe the PSU. I think it has happened before.). When I turned it back on, I was only able to connect as far as my router (192.168.1.1, a D-Link Gaming router that has always been very good to me). I could not make it to my modem (192.168.0.1, a Quest DSL modem. Once I can get here, then usually I'm good to go 100%).
I tried again this afternoon, and no change. I then get the crazy idea to unplug the ethernet cable from it's PCI-card home and return it to the onboard port (which I long ago declared defunct). Immediately after plugging it into that port, I ran "ping 192.168.0.1" and I started getting returns. I open up Firefox and try to load an external page, and nothing happens. I go back to the console that I was pinging from, and it had stopped. I start pinging my router, and no luck. What I conclude from my little experiment is that the router is not at fault.
1. It did not change at all between being at 100% and being at 0% after reboot.
2. I was able to get returns from the modem, past the router, for a brief period of time while using the defunct ethernet port.
Since I never had these problems before updating to 11.4, I'm inclined to believe that it was the update that started these problems.
I just finished a fresh install of 11.3 on an HP 7900 small form factor and have no network connectivity. In Network Tools eth0 shows the state as inactive. Network Connections didn't have a connection, so after letting it create one there is no MAC address. I copied and pasted the MAC address from Network Connections eth0, set up a static address with default gateway, netmask, etc. all set appropriately and rebooted. Still no joy.
I want this to get an address via DHCP, I just set up a static address for testing.11.2 sensed the NIC without issue, but 11.3 doesn't seem to like me right now.I wanted to get this deployed on 40 machines today. Oh well.
I'm new in SUSE 11.4. My problem is: I'm using Alfa AWUS036H card. It's recognised and I can establish connection to my network, but cant get to Internet. I can't surf the web cos Firefox tell me that connection is timed out. Now I'm confused why I can't surf the web even if I'm connected. Also, I trayed to instal linux drivers for this card folloving Ubuntu "how to" and it just dont work.
View 4 Replies View Relatedwith the ifup method everything works fine. But now I bought a wireless card, so I prefer to use the network manager to manage my connection. On my computer I need a static IP for wired connection, so I created a new wired connection and I called it "wired connection". But network manager always connect automatically to "Auto eth0" and I can't find how to modify this connection. Setting "wired connection" as default didn't change anything, probably becouse it need me to unlock the default wallet... Now, another problem, I really don't know why network manager applet doesn't appear on system tray, but I'm sure that I'm using it instead of the ifup method.
View 9 Replies View RelatedI installed a simple VPN pptp. Works fine to connect to the linux server. However I would like to connect my other linux-server and (more important) my old Novell 6.0 server. Anyone have an idear what I need to change?
View 3 Replies View RelatedI am trying to Setup citrix ICA client 9 on Ubuntu 9.04 Server. I installed it very easily and I am not getting any lib error also. But when I try to connect to the citrix server, it fails with a pop up saying "Error in Network Connection Network or Dialup connection may be preventing ......" This is driving me crazy from 3 days. My project is to check the feasiblity of a Linux desktop
View 1 Replies View RelatedI'm trying to enable a VNC connection from a Windows machine to remotely connect into my openSUSE machine (11.2, KDE, 64-bit), but I cannot get any desktop environment to load up at all. It just comes up with a blank screen and a black cross for a cursor. What I want is to be able to see exactly what I would normally see if I were sitting in front of it, rather than go into a 'virtual desktop' as appears to be the case. Ideally I would want to go into the KDE desktop environment in this instance, and it would also be nice if dual monitors could enabled for each remote session. How do I go about enabling my chosen environment?
If it makes any difference at all (although I doubt it does), I'm also using PuTTY in Windows in order to make an SSH tunnel to allow secure access, and I'm quite sure I've enabled all the necessary services for all of the above under the YaST Firewall (by the way, on a lesser note, do I need PuTTY to be installed at both ends for the SSH tunnel to work properly?). If you need a screenshot or output from terminal of sorts this can be arranged.
It is just 3 days that I am using Linux Opensuse 11.2. I got a problem with Internet connection: I have HUWAEI E1550 3G Modem, but I have no idea about using it on Linux OpenSuse 11.2. Now I use it Windows7, there is no problem, because there is a program and driver for modem.
View 1 Replies View RelatedI have bought a TV which has possibility to connect via LAN to Internet. At this moment I have no router but I suppose it should work also via PC where is 2nd net card. (of course PC must be ON)
So I connect TV to PC to one net card and from 2nd to internet (provider socket). But how should I set the PC to work it? Allow both cards, it is clear but is it enough? I dont suppose
PS: if important, KDE and oS 11.3
I have problems in connecting to the internet.I have a new desktop.I installed the opensuse 11.3 64bit.I connect to the internet without any problems.I've installed the necessary update files.I continue to use it without problems.But today I cannot connect to the internet.I opened my desktop with Ubuntu CD and I could connect to the internet.I installed the opensuse 11.3 64bit again.Problems continued.I've written a static IP.
View 5 Replies View RelatedI'm installing 11.4 on a late-2010 Macbook Air. I've forgotten my USB ethernet adapter, although I'm not sure if it would even work in OpenSUSE. Is there a way I can install packages manually (via USB drive) to get wireless working?
View 1 Replies View RelatedI have problem after install opensuse 11.2 on lenovo R61. I have no connection to internet, although on liveCD (opensuse 11.2) is internet connection functional. In ubuntu or opensuse 11.1 was all OK, connection was functional.- at DSL Configuration / Ethernet Card is Unknown device- in hardware is Card: 82566MC Gigabit Network Connection (eth0)- modprobe wl write it FATAL: Module wl not found.
View 9 Replies View RelatedI had work well with opensuse 11 and the internet also work well but when I turn off my computer and then use the XP and work with it. I find out the connection with the internet doesn't work in the opensuse 11. I made a repair and format to opensuse 11 but without any change the net still doesn't work.
CPU Pentium4
Motherboard Gigabyte intel 945 S-series
Dial up connection
I have no experience with opensuse.
I was trying to activate my wireless connection .... in turn did something that triggered eth0 no-carrier when "ifstatus eth0"
View 2 Replies View RelatedI have a successfully connected VPN connection. When hovering on the networkmanager applet it show beside the wireless connection also the connected VPN. The icon also changed from staircase-bar to staircase-bar with forelock. Oh yeah I'm using GNOME desktop.However when right-clicking on it and choose Connection Information I can only found tab for the wireless connection. How can I have the information tab also for the VPN connection, showing like IP address and gateway used?
View 1 Replies View RelatedI've just installed opensuse 11.2 with the network installation iso. During the installation, it has got the IP via DHCP without any problem, and I has downloaded all the needed packets without problems... But when the installation finish.I have no network connection It's strange, because I have IP address, I get the IP from the DHCP server, and I can see the IP addreess if I do "ifconfig", the default route and even the DNS servers in the resolv.conf file; but I cannot ping my gateway (that is the DHCP server as well!!), I cannot ping anything in my network and either anything in internet. I see a network error at the start, but it finally gets the ip address. In the dmesg, the last message repeats over and over. The machine is a Hyper-V virtual machine, but as I said... I worked very well during the installation, I don't know what is going on. I've tried to reinstall, but it doesn't make any difference
View 2 Replies View RelatedI just tested Networkmanager on OpenSuSE 11.2. I tried with my wired connection and it works.
I thought I test to connect with network sharing with my Android phone. The Android phone connects according to Networkmanager, but I'm not sure if it actually works as the wired connection is still active.
I tried to figure out how to disable the wired connection, but eventually gave up and just pulled the wired network plug.
But surely, there must be a way to disable connections from Networkmanager?
I recently took a WIRED internet connection (from the people who provide cable TV) and switched from ubuntu to openSUSE11.2. . I am not able to set up an internet connection in openSUSE 11.2. I have been given a static IP, and the following info
subnet mask
gateway
dns server
alternate dns server
how do i setup an internet connection with these in openSUSE 11.2.
I would like to know how to configure a pppoe connexion? I am testing version 11.2 on live cd but I can't manage to connect my laptop. I used the "green plug software", I filled all the blanks (I am not a total beginner because I have been using Mandriva for a year) but afterwards I can't select pppoe instead of eth0 What should I do?
I read on this forum NET INSTALL PPPOE - Alionet, communaut francophone d'entraide openSUSE et SUSE Linux that the only reason that I can't configure a pppoe connexion is because I am using a live version of 11.2 as result that it only recognizes an ethernet connexion and a modem (everything I said, is said in the forum I linked, but you'll have to read it in french )
I try to configure a pppoe connexion to Tl2, my internet connexion provider. I live in France. My modem is a Bewan ADSL ethernet 100, no need to configure it.
Today I switched from Ubuntu to OpenSuse. But I can't setup my Ethernet connection.I have 2 PCs connected with a crossover cable, one with Ubuntu, the other with OpenSuse 11.3. Lights are on in both NICs.
View 9 Replies View RelatedI tried to build a PPP connection with umtsmon, but failed. I'm using a ZTE MF110 Stick. The reaction from my provider's support was succinct: "Linux untersttzen wir nicht." (We don't support Linux.)
The hardware seems to work fine, the stick shows a green light, and I sent a test SMS via umtsmon. The umtsmon interface successfully identifies my Provider, but does not connect.
Here is part of umtsmon debug output:
Code:
UIState::setState(6 -> 6)
##P4 t=133: ConnectionInfo:InhibitionCount ++, now is 1
##P3 t=133: TempSerialPort::TempSerialPort()
##P5 t=133: 0x75a6c0 = Query::setSerial(0x7fffece12a00)
##P3 t=134: Serial::openDev('/dev/ttyUSB2') as FD 8 - Serial instance
[Code].....
I am running 11.2 and set ssh to boot at runlevel 3 and 5 through yast and started the service through the terminal. I have turned off the firewall on my wireless router and in the local firewall. When I try to connect from a machine in my office, I get the following
Code:
ssh: connect to host xx.xxx.xx.xxx port 22: Connection refused
When I run telnet from the machine, I get:
Code:
telnet: connect to address xx.xxx.xxx.xx: Connection refused
telnet: Unable to connect to remote host: Connection refused
netstat -tlnp on my machine shows:
Code:
tcp 0 0 :::22 :::* LISTEN 31622/sshd
I have freshly installed OpenSUSE 11.3 64 bit and reimported my old openvpn connections via Network Manager. Connection can be established fine, but after 3 to 6 seconds (pings) it will stop to receive any packets on the tun device.
I tried disabling the firewall, starting openvpn manually, no avail. I checked the message log and the openvpn output, no messages recorded.