OpenSUSE :: High CPU Load From XOrg And Gconfd-2 With Nvidia?

Jan 9, 2011

I just posted about this in this thread, but as the other thread was started by a KDE user then I thought I'd post here as well. I've had high CPU usage for a few months now - probably since trying the 0.9 branch of Compiz then dropping back to the default openSUSE builds (XOrg and gconfd-2 running a Core i5 at about 30% on every core*). I've now finally found a solution after deciding I wanted to fix it once and for all.

Once again, the Ubuntu forums come to the rescue with this thread (I don't like the distro as a whole, but I do find the forums useful!). I'm using Compiz, but it turns out that Metacity was running as well. A quick "killall -9 metacity" and the gconfd-2 process has vanished and XOrg settled down to its normal 1-2% (which is reasonable when I've got a Conky config refreshing every fraction of a second to repaint a sound visualiser!). Now I just need to find out why Metacity starts when I'm using Compiz...

* according to Conky's per-core graphs, although top only reported 15% overall and the Conky "top 3 procs by CPU" reported a measly 3% for each process, so someone's maths was out somewhere!

View 3 Replies


ADVERTISEMENT

CentOS 5 Hardware :: NVidia Driver Xorg High CPU Utilization

Nov 12, 2010

I installed the NVIDIS driver for 64b Linux, and now I face a high cpu utilization (up to 40%) in the XORG when I swith from one application to another. I need the driver because otherwise some web pages are rendered with a something like a watermark

LSPCI
01:00.0 VGA compatible controller: nVidia Corporation G98M [Quadro NVS 160M] (rev a1) (prog-if 00 [VGA controller])
Subsystem: Dell Unknown device 024f
Flags: bus master, fast devsel, latency 0, IRQ 169
Memory at f5000000 (32-bit, non-prefetchable) [size=16M]
Memory at e0000000 (64-bit, prefetchable) [size=256M]
Memory at f2000000 (64-bit, non-prefetchable) [size=32M]
I/O ports at df00 [size=128]
[virtual] Expansion ROM at f4000000 [disabled] [size=128K]
Capabilities: <access denied>

NVidia driver
260.19.21
uname -r
2.6.18-194.26.1.el5

View 3 Replies View Related

Debian Multimedia :: Proprietary Nvidia Driver - High CPU Usage Xorg

Aug 7, 2015

I recently switched from jessie to stretch on both i encountered a jerky ui in gnome 3. after a longer research i noticed xorg consumes over 80% of my first cpu-core while moving a window. for testing purposes i switched back to the nouveau driver and there is no high cpu usage while moving a window, also the ui is smooth.

i tried 3 different nvidia driver: the one from the debian repository, the current stable and beta driver from the nvidia site. i noticed on all 3 the same problem.

Code: Select alldaniel@Daniel-PC:~$ glxinfo | grep rendering
direct rendering: Yes
    GL_NV_path_rendering, GL_NV_pixel_data_range, GL_NV_point_sprite,
    GL_NV_path_rendering, GL_NV_pixel_data_range, GL_NV_point_sprite,
    GL_NV_path_rendering, GL_NV_pixel_buffer_object, GL_NV_polygon_mode,

xorg.log: [URL] ....
dmesg: [URL] ....

system:
nvidia gtx 760
intel xeon e3-1230v3

View 1 Replies View Related

OpenSUSE :: High CPU Usage With XORG / Cause Of This?

Dec 14, 2010

I just upgraded KDE on my openSuSE 11.2 installation. I have never had any problems doing this in the past, but this time, when I rebooted, I noticed that after a few seconds of idle time, my CPU usage goes sky high. I ran top in a console and noticed the culprit was xorg. I am using an NVIDIA card on an AMD64 3200+ with 1 gig of memory. KDE version is currently 4.5.85.
Like I said, I didn't have this problem until the last update. Any ideas as to what could be causing this?

View 9 Replies View Related

OpenSUSE :: Digikam & Xorg Heavy Cpu Load?

Oct 24, 2010

i run right now digikam and rebuild my thumbnails. It seems like that this task takes a lot of cpu power and its not digikam itself, rather xorg takes the load. Is this right? I just wonder.

[Code]...

View 9 Replies View Related

OpenSUSE Hardware :: Xorg And Can't Get The Compiz 3D To Load

May 29, 2010

I have dual monitors and running openSUSE 11.2 with a Nvidia 260 with 897ram on the card with 16GB system Ram and AMD dual core CPU. I can get the monitors to work just fine with the Nvidia drivers i just cant get the Compiz to load.Here is my xorg.conf. I have had it running before but just cant rember what i did.

# nvidia-settings: X configuration file generated by nvidia-settings
# nvidia-settings: version 1.0 (buildmeister@builder58) Fri Mar 12 02:13:46 PST 2010
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 1.0 (buildmeister@builder58) Fri Mar 12 02:12:40 PST 2010
[Code]...

View 2 Replies View Related

OpenSUSE Install :: Change /etc/X11/xorg.conf From NVidia To Nv To Get A X To Run In Xen?

Aug 29, 2011

I have the nVidia driver on my desktop kernel set-up but have to change /etc/X11/xorg.conf from nVidia to nv to get a X to run in Xen. Whilst this works, is there a way to tell Xen at boot time to use nv rather than nVidia so I don't have to edit xorg.conf each time?

View 2 Replies View Related

OpenSUSE Hardware :: Cannot Access 1280x800 Resolution Even Though It's In Xorg (nVidia)

Feb 21, 2010

I am running 11.1 with an nVidia GeForce FX 5200 graphics card and I have configured the monitor and graphics card via "sax2 -r -m 0=nvidia". My xorg shows all of the correct monitor settings and screen resolutions, yet when I go to the Display settings or nvidia-settings, it does not offer me any of the 16:10 aspect resolutions that are in the xorg.conf file.

Here is my xorg.conf:

# /.../
# SaX generated X11 config file
# Created on: 2010-02-22T00:43:08-0500.

[code]....

View 7 Replies View Related

OpenSUSE Install :: While Checking Xorg.0.log Found I810 Module Is Failed To Load?

Dec 15, 2010

I have installed suse 11.2. Sometimes while using (firefox, okular, open office etc) x server restarts & comes to login screen. While checking Xorg.0.log i found i810 module is failed to load. Is this causing the x server restart?

View 9 Replies View Related

OpenSUSE Hardware :: 11.2 - IME Are 99% Related To Conflicts With An Existing /etc/X11/xorg.conf And NVIDIA

Feb 11, 2010

Lately I see a lot of posts/threads on NVIDIA cards and disfunctioning desktops. People rely on older posts and howto's, and run sax2 after driver install (either from repos or "hard way"). Symptoms also appear after updating 11.1 to 11.2 The problems IME are 99% related to conflicts with an existing /etc/X11/xorg.conf, which in 11.2 has become obsolete, though it will be read and used if it's (still) there.

On openSUSE 11.2 we have hardware autodetection and -configuration for everything. So no need for an xorg.conf to configure the X-server. on 11.2, follow this, if NVIDIA driver is installed correctly, but still no proper desktop experience:

[Code]....

View 9 Replies View Related

Fedora :: Installing Kmod-nvidia And Xorg-x11-drv-nvidia-libs.i686

Jan 22, 2010

I installed Fedora 12 nowdays and tried to install the driver as Leigh posted in here: [URL]...Well i had some depadency trouble by installing kmod-nvidia and xorg-x11-drv-nvidia-libs.i686. I enabled rpmfusion repo of course. I don't have anything isntalled just the base programs what fedora installs. I updated the kernel and installed kernel-devel aswell.

This is what i got:

Code:
[root@Nuclear pinter]# rpm -Uvh http://download1.rpmfusion.org/free/fedora/rpmfusion-free-release-stable.noarch.rpm http://download1.rpmfusion.org/nonfree/fedora/rpmfusion-nonfree-release-stable.noarch.rpm
Retrieving http://download1.rpmfusion.org/free/fedora/rpmfusion-free-release-stable.noarch.rpm
Retrieving http://download1.rpmfusion.org/nonfree/fedora/rpmfusion-nonfree-release-stable.noarch.rpm
warning: /var/tmp/rpm-tmp.fNroQP: Header V3 DSA signature: NOKEY, key ID 49c8885a
warning: /var/tmp/rpm-tmp.zdIa6C: Header V3 DSA signature: NOKEY, key ID b1981b68

[Code]...

View 1 Replies View Related

Ubuntu Installation :: 10.04 To 10.10 - Nvidia 96 With Xorg 1.9 - Nvidia-xconfig: Command Not Found

Jan 24, 2011

i am having a problem with my just recently upgraded ubuntu 10.10 ive search google and forums for well over 4 hours with no luck so im asking here. Now i know nvidia 96 has problems with xorg 1.9 but i installed the updated nvidia 96 driver that supports xorg 1.9 through maverick-proposed and i dont have nvidia control panel under system->preferences and if i types sudo nvidia-settings in terminal i get it says im not running an nvidia driver but the hardware driver reports it as activated but not in use and nvidia settings also tells me to run nvidia-xconfig but it says this when i do sudo: nvidia-xconfig: command not found

View 6 Replies View Related

Ubuntu :: Xorg Refusing To Acknowledge High Resolutions

Mar 6, 2011

On my Debian 6.0 squeeze system, after reconfiguring GRUB and installing QEMU, X is sticking in 800x600 and not 1024x768. Yesterday I had no problems. Using a Rage Pro AGP 2X with 8 MB RAM (mach64 driver) on a i686 system. The kernel is the latest from squeeze's repo (2.6.32-5) and booted with the same settings as before despite the GRUB change to purge old 2.6 kernels.

View 1 Replies View Related

OpenSUSE Hardware :: NVidia GeForce2 GTS / Pro Driver - Failed To Load Module "nvidia" (loader Failed, 7)

Feb 17, 2010

I`am trying to install drivers for a very old graphics card GeForce2 GTS/Pro on Suse 11.2. I downloaded driver NVIDIA-Linux-x86-71.86.13-pkg1.run and install it successfully. But when I launch "sax2 -r -m 0=nvidia" it crushes with error "isax: could not import file: /var/cache/sax/files/config at /usr/sbin/isax line 199"

[Code]....

View 9 Replies View Related

Ubuntu Installation :: 10.4 Upgrade, Xorg, Cpu, Fans Gone Nuts Running High/low?

Apr 28, 2010

I upgraded my Asus Eeepc 900a to 10.4 yesterday. Since then, Xorg has averaged between 30-40% CPU, and my fans have gone nuts running high/low/high/low, ad nausium.

Any ideas what might be going on? Another clue perhaps: on reboot or shutdown, I get a "program not responding" message with "unknown" as the hung program. I have not been able to determine what this program is or if it is related to the hyperactive Xorg.

View 9 Replies View Related

Debian :: Can't Get High Resolution With Vesa Xorg Driver (Intel 82845)

Feb 20, 2011

With the upgrade to Squeeze and the 2.6.32-5-686 kernel, my Dell GX260's 82845 video chip suffers from the documented intel driver bug (freezes within a few minutes). I tried to fall back to the vesa driver, but am only able to get 640x480 resolution. The monitor is an LG L1720P.

I turned off kernel mode setting (via /etc/modprobe.d/i915-kms.conf), and modified xorg.conf -- added Modeline entries (from gtf) and
additional Mode lines to try to force resolution. Relevant portions of xorg.conf, dmesg and Xorg.0.log are shown below.

xorg.conf:

Code:

Section "Device"
Identifier "Generic Video Card"
Driver "vesa"

[code]....

View 6 Replies View Related

General :: Xorg High Cpu Usage System/video Not Running Smoothly?

Feb 18, 2011

I have just started to have a problem with Xorg it is always using at least 30% of my CPU, and the whole system does not run smooth so if I play a video it does not run smooth, it judders, also even if I drag an icon it judders across the screen. Im running Ubuntu 10.10 2.6.35-25-generic x86_64 VGA compatible controller: nVidia Corporation G98M [GeForce G105M] (rev a2)

View 5 Replies View Related

Debian :: High Load Always

Sep 15, 2015

I have a debian system with the following version you can se bellow. My problem is that one one single core of 4 it's running 100% all the time and i cant seem to find out why. The load is also high(load average: 0.91, 0.75, 0.40) because of this. This keeps happening even after reboots. The system if freshly installed twice and the same problem occours as soon as it boots. Something called kworker is running and causing the load / CPU load, is that normal for a fresh install??

root@Cyberdyne:/# lsb_release -da
No LSB modules are available.
Distributor ID: Debian
Description: Debian GNU/Linux 8.2 (jessie)
Release: 8.2
Codename: jessie

View 5 Replies View Related

OpenSUSE Hardware :: Can't Load User's Graphical Environment After Nvidia Driver Installation

Jul 20, 2011

I have my first problem with drivers in Linux! I installed openSuSE 11.4 x86 on my computer (Intel Dual-Core 2,5 Ghz; Nvidia 7300 GS) and after installing graphical drivers (proprietary) I can't load the system. All I have is a progress bar of user's profile loading and playing the startup sound. I already installed openSUSE 11.4 x86_64 version on this computer and there was no problem with drivers.

View 8 Replies View Related

General :: Load Average Too High

Aug 10, 2011

I wrote a script to extract and get the the name of *.gz in a foler . Since running that script every 10 minutes, load average on my server increases more than 10.I checked with 'top' and it showed many D process.

View 2 Replies View Related

Server :: Apache Load VERY High - How To Fix It

Apr 2, 2011

on an old server of mine, as soon as apache is started, the load average that I get to see with 'top', that normally is under 1, now just steadily climbs up and up to easily 150, in fact disabling the webserver from serving any webpage. I've checked netstat, and I'll try to upload the output. The ip's that are in there I've blocked with iptables. But that doesn't help or so it seems. I see nothing weird in the error logs. As soon as I stop apache, the load goes back to normal. As soon as I (re)start it, up it goes again. What can cause this and how do I get rid of it?

p.s. It's an old server, fedora3 or so, and I've got a new one to which I'll transfer the domains, but until that's completely done, I'd like this one to run as it has for years...

View 1 Replies View Related

Server :: Load Average Is High

Dec 14, 2009

The load average is almost 1.06, but cpu is not 100% utilized... I am just wondering why load average is 1.06 in that case still ? (well i monitored cpu for long time, it never exceeded above 40%)can anyone explain the reason behind it ? Also is the system over utilized in this case ?

View 3 Replies View Related

Server :: Load Average Going High Between 60 - 70

Aug 18, 2011

I am having Red Hat LINUX 5 Enterprise Server and facing problem regarding very very high server load (load average is going high up to 60-70)due to which server is getting hang.

View 7 Replies View Related

Fedora Installation :: Wine Installation Produces Error "xorg-x11-drv-nvidia Conflicts With Xorg-x11-drv-catalyst" On 11 64bit

Oct 8, 2009

Error: xorg-x11-drv-nvidia conflicts with xorg-x11-drv-catalyst
Error: xorg-x11-drv-catalyst conflicts with xorg-x11-drv-nvidia

I have followed the guide to install ATI proprietary drivers using RPM Fusion.

View 3 Replies View Related

Ubuntu :: 10.04: High Load Average At Idle

May 5, 2010

Since upgrading from 9.10 to 10.04, my system is noticeably less responsive and exhibits halting behavior for at times 10s of seconds. There is nothing obvious in the various logs that I can find. The only objective indication I can find that demonstrates that something is seriously wrong is that my load average never drops below 0.5 and is often over 1.5, even at idle. In this situation, top/ps/whatever shows very few processes running (usually just top). This suggests to me that either the new kernel scheduler is horrible or that something new is resulting in blocking I/O or other uninterruptable sleeps.Typical top output:

Quote:

top - 12:18:01 up 1 day, 49 min, 5 users, load average: 1.42, 0.86, 0.71
Tasks: 262 total, 1 running, 261 sleeping, 0 stopped, 0 zombie
Cpu(s): 0.9%us, 0.8%sy, 0.0%ni, 97.6%id, 0.0%wa, 0.0%hi, 0.7%si, 0.0%st

[code]....

View 9 Replies View Related

Ubuntu :: Unusually High System Load

Jul 2, 2010

i've been using 10.04 since may and it's been good to me thus far. BUT recently, i've been experiencing unusually high system loads. it will happen at random it seems. for instance, it just did it a few minutes ago when i turned on and mounted a external firewire drive. i also had ogmrip open, but NOT running as well as transmission and pidgin. yesterday, i was encoding a rather big movie with ogmrip and around 25%, the system load quickly increased to 10 and held there until i force quit ogmrip. it went back to normal after the force quit.

a previous night, i was installing the popular ubuntu themes via the terminal. at the same time, i was also using ogmrip and the system load shot up during the download/install and held there the rest of the night. sooo...unless it's somehow related to ogmrip i don't know what's going on. it even did it when ogmrip WAS NOT processing any video, just simply open.

View 2 Replies View Related

Red Hat / Fedora :: High Load Averages In One Of Server

Jul 6, 2010

I am facing a high load averages in one of my linux server find the output of the top command.

[code]...

How to reduce the load averages.

View 3 Replies View Related

General :: High Load During Firefox Downloads

Nov 14, 2010

During downloads, the top command shows the Firefox process at 100% CPU. Yesterday I tried to download an .iso image. After a few hours the Firefox window would not refresh nor would it respond to input. I tried the wget command. It used negligible CPU time and completed in 28 minutes.

This problem is easy to reproduce because it happens every time I download a file in Firefox. It also happens when I use a fresh profile to run Firefox without any extensions or plugins.

This is Firefox 3.6.12 on Fedora 14.

View 3 Replies View Related

Server :: Apache Message: Load Is Too High

Jul 28, 2010

I have a apache cluster with more than 10 nodes, based on ldirector and heartbeat. The problem is that I cannot predict if my nodes will handle the traffic in the next day (hosting a website based on daily campaigns). So I decided to limit the number of active connection on the nodes (from apache), but this is only a temporary solution. I want to create a page that will appear to users that are getting over the limit. Has anyone made this before? Can you tell me how is it possible (I don't want a how to, just a starting point to study)? I think squid can do it, but I don't know how to search for it. To give you an example of what I want, you can see the same thing on deviantart.

View 3 Replies View Related

General :: High Load Average Investigation

Feb 10, 2010

I have High load on my server and my investigation shows nothing (so i believe that my investigations is wrong ), the load average in this moment is 10.13, 9.47, 8.24. , mentioning the below.

- The disk utilization (all the disks) is near 0, as the result of the IOSTAT
- There is no blocked processes (as a result of VMSTAT).
- I have two processors (dual core) , the maximum load average should be something around 4.
- The server always have above 8 load average in all times interval.

btw , my OS is RHEL AS release 4 (Nahant Update 7)Kernel :Linux 2.6.9-78.ELhugemem #1 SMP i686 i686 i386 GNU/Linux

View 8 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved