OpenSUSE Hardware :: Prompted To Use The NVidia Drivers?
Jul 15, 2010
Just got openSuSE 11.3 installed on my system and so far I like it better than my previous distro (Xubuntu).However, under YaST, it's showing a Vendor Driver CD, which I think might be for my nVidia chipset on my Zotac ION motherboard. How do I enable full graphics support for my system?
I Xubuntu, it automatically picked it up and prompted me to use the nVidia drivers. It also added the nVidia PPA to the Software Sources. Does openSuSE have anything like this?
opensuse 11.2 ,my monitor keeps going to sleep or somthing and this is a problem when im watching videos,ive set screens power setting but they dont seem to be whats doing it.im running a nvidia gtx260 and have installed nvidia drivers for series 6 and up.dont know if its the divers or somthing else.
I've had Ubuntu installed on my desktop for a month now, and its all worked like a charm, so I'm thrilled. I then decided to install it on my old laptop as well to see if I could breath a bit more life into it, and to get used to working Ubuntu a bit more. The laptop had 18.6GB partitioned to C:// drive or windows XP, and an empty 18.6GB D:// drive, so I deleted the D:// drive in XP using the Microsoft disk utilities tool, all well and good. I then did a clean install of Ubuntu-9.10-desktop with an Ubuntu CD into the largest continuous free space, and it set it up nicely. When I first booted it up there were a ton of updates to install, as there had been on the desktop first time, which I dutifully installed. As on the desktop a little notice popped up telling me to install the NVidia Proprietary driver for the NVidia card (specifically "NVIDIA accelerated graphics driver (version 96)[Recommended]"), as it had when I installed it on the desktop, so I chose to install that and then restarted the computer.
On restarting GRUB2 loaded, and it booted Ubuntu. I then saw the little white logo on the black screen for a couple of seconds, and then the screen goes completely white, with some pixels left behind fading to white slightly slower. First time through I held down the power button to force shut down, and on restart exactly the same thing happened. This time I held down alt+sysrq and went through the R, E, I, S, U, B sequence, however as opposed to usual I didn't get a black terminal-like screen after hitting any of the buttons, although it did reboot on B. It did boot correctly in recovery mode, however I was at a loss what to do here. Incidentally, the same problem occurred when I booted to previous version of the kernel as well.
Then I decided that as I didn't have any data to lose, and it was still early in the day, I'd do a clean re-install. This time I chose to ignore the updates, and just install the NVidia driver as prompted to check that it was the driver causing the trouble. Having installed the driver and restarted I got exactly the same problem as before - definitely this pesky NVidia driver, not any of the updates.So here I am at clean install 3, having just got all the updates, but not having downloaded the NVidia driver as prompted, with little desire to go through yet more reinstalls. My questions are:
1) Do I need to install this NVidia driver? The rest of the computer specifications are fairly paltry by modern standards, and I won't be doing anything graphics intensive on it (the most graphical program will probably be Battle for Wesnoth) and I I don't need to install it, not installing it seems to be the easiest way to solve the problem.
2) If I do need to install it how would I go around doing this without getting my charming white screen?
3) Is there a way of removing the driver from recovery mode that doesn't involve a clean install again? I have tried sudo apt-get purge nvidia-driver, which tells me there isn't any installed. I have tried sudo rm /etc/X11/xorg.conf which made no difference. I have tried dpkg-reconfigure xserver-xorg and this didn't help. I have tried a couple of other commands as well but I can't remember them, however I would probably recognise them if I saw them again.
Onto System information - pulled from listed specifications and SysInfo:
General System Information Release:Ubuntu 9.10 (karmic) GNOME: 2.28.1 (Ubuntu 2009-11-03)
After installing 11.3, I realised that my graphic driver is not working as desired. I have a Compaq CQ60-430SA laptop with an NVIDIA 8200M graphics card. Earlier with 11.2, I had some proprietary NVidia drivers and my graphics were smooth. However, I am not getting the same performance with Nouveau...
As can be seen from the screen clipping below, the images especially in the preview mode and the icons look jarred (highlighted in red). I have no complains with the video but the images and icons do look shabby at times and therefore I want to switch over to the proprietary NVidia drivers.
I need to install the latest drivers for my Nvidia card. I have the Quadro FX 1800.I don't think the Nvidia One click installation will work with this card.I downloaded the drivers from Nvidia and tried to install them but their directions are very confusing. It says "exit x windows" and "restart in init 3". I don't know what that means.Can someone tell me step-by-step how to compile and install the nvidia drivers?I have opensuse 11.2 64-bit clean install with all the defaults, and the Quadro FX 1800.
Lappy is a Dell XPS M1330 Intel core 2 T7500 2.2Ghz 4gig Ram Nvidia GeForce 8400M GS HDD 320
1 64bit system installs but wont let me do updates so now using 32bit thats ok 2 How do I update drivers? My screen seems to have ghosting around the edges
3 On firefox when scrolling down the page its jerky Ive used firefox on most of my Pcs and never had this problem Im duel booting ubuntu and suse and using the internet on ubuntu so far other than these problems suse is fine
When i'm trying to compile nvidia closed drivers, i got an error. I've tried binaries one on nvidia suse repo, but as i installed kernel 2.6.32-41 they didn't work. My laptop is a lenovo T61, with nvidia quadro nvs 140m, and intel chipset. And i'm trying to instal driver version NVIDIA-Linux-x86_64-100.14.11.
That's the error i get when executing nvidia-installer: Code: nvidia-installer log file '/var/log/nvidia-installer.log' creation time: Fri Feb 19 20:56:25 2010
I installed OpenSuse Gnome version 64 bit on a HP laptop DV7 Intel Dual Core with nVidia 9600 GM cardAll went well, until after I had installed the nVidia drivers from this page: NVIDIA drivers - openSUSEI selected the Geforce 1-click install and Yast went on to installl all the packages (a lot of 32-bit),took about half an hour.I logged out/in, and could work as normal, until I rebooted. Maybe I waited not long enough (5 minutes), but the screen was blank, then I gave up.Anyone has an explanation. I can always re-install everything, but then what went wrong with the nVidia package
I have a strange problem: Due to my small monitor I have set the gnome panels on top and bottom to auto hide. After installing the nvidia drivers the panels do not appear if I go to the edges with my mouse. If I switch the resolution to VGA (640x480) however, the panels appear again, but not at top/ bottom but in the middle of the screen.
My amarok crashes everytime. I saw an similar problem posted at OpenSUSE 11.3: Amarok crashes on startup. And I suspect this is because of the nvidia drivers that I installed, just as is the case in the above mentioned thread. What should I do to overcome this now? Is there a solution posted? After I read the above thread, I deleted all the repositories except for the four. I had these following repositories prior:
Alright I've been trying despretly to installed the nvidia drivers.If reinstalled them over and over but it just wont work. I have Gefore GTX 275 and I installed it using the one-click install.
It apperently installs but it doesn't run or something.
i've been attempting to get to the bottom of this issue for the past few months, without much luck. i'm currently running 11.3 64-bit (the issue also existed in my previous 11.2 64-bit install) and whenever my laptop is unplugged, the x server will intermittently crash. this issue can be provoked by running flash applications like videos but the same issue will also occur by simply navigating the desktop. the messages log reports the following:
~~~~~ x server for display :0 terminated unexpectedly ~~~~~
the laptop is an alienware m15x with an nvidia gtx 260m. i initially suspected that this was some sort of an acpi issue so i tried disabling acpi for the nvidia card via the "connecttoacpid" xorg option. this did not make any difference so i went as far as shutting down the acpid service. this also did not make any difference. as a quick test, i uninstalled the proprietary nvidia drivers and that seemed to resolve the issue but given the limited functionality of the oss driver, this is not a suitable workaround. keep in mind, i did not run under the oss driver for very long so this result could be just a false positive.
i have just installed opensuse 11.3 on my PC and updated all packages and all and then i installed nvidia drivers from this link SDB:NVIDIA drivers - openSUSE i downloaded the 1 click install file nvidia.ymp and installed the driver successfullybut then when i rebooted the PC for the driver to work,it doesn't work,and when i go to system>look and feel>desktop effects and i try to enable the effects i get the message that i cant enable the effects it gives me this message "Desktop effects are not supported on your hardware / configuration. Would you like to activate them anyway?" PS i say "no" to this message and it closes but i notice there is a constant use of 33% of the CPU and theres an unnamed/unknown process in the system monitor that keeps appearing and disappearing...thats quitrd because i installed opensuse 11.2 and 11.3 before and i never had these problems
I can install the nvidia driver for my card easily with yast but would like to try using nvidia's own installer. There is a paths problem. I've spent some time looking at 11.4 kernel build paths and they seem to be circular so the installer will not find what it needs. The installers help in this respect is as follows.
Code: --kernel-source-path=KERNEL-SOURCE-PATH The directory containing the kernel source files that should be used when compiling the NVIDIA kernel module. When not specified, the installer will use '/lib/modules/`uname -r`/build', if that directory exists. Otherwise, it will use '/usr/src/linux'. Obviously it will fail on the build directory and fall back to usr/............ where linux is a symbolic link linux -> linux-2.6.37.1-1.2
which must be the one in the same directory but it fails to find either type of auto conf file From this I assumed that it just needed pointing at the correct build directory but this turns out to be symbolic link
However when pointed here it still doesn't find what it needs and falls over looking for the kernel header this time. I thought that the idea of the /usr/src/linux link was to standardise kernel building but if suse use it for something else or nvidia make the wrong assumptions just where should the installer be pointed?
I am having a challenge to install drivers on this machine with the OS and graphics card stated in the subject. To date I have tried different ways and they are broken in the steps or in the results I get on my machine. The how-to written by ajohnw Installing an nvidia driver - easiest I have found to date. results in a file or directory not found when I try to execute
Code:
/etc/bin/nvidia-xconfig
The article SDB:NVIDIA the hard way results in the following error (copied from the error log):
Code:
ERROR: The kernel header file '/usr/src/linux/include/linux/version.h' does not exist.The most likely reason for this is that the kernel source files in '/usr/src/linux' have not been configured.
Researching how to resolve that error and I can't find anything relevant to openSUSE 11, closest version being openSUSE 9.Lastly, I've tried this SDB:NVIDIA drivers and for some reason it does not generate the xorg.conf file. At least that's what I am concluding. I go through the steps, reboot the system and boot only to a command prompt. Navigating to /etc/X11/ there is no xorg.conf and I have to copy xorg.conf.install to xorg.conf to get back into the Desktop.
I have an nVidia GeForce 7600GS with a dual monitor setup. A 19" Dell @ 1280x1024, and a 19" widescreen Acer @ 1440x900. The Dell is attached via DVI, and the resolution is detected properly, and set, but the Acer is connected via VGA, and so the native resolution is unkown to the nvidia control panel. It will only let me set the resolution up to 1024x768. I had it create the xorg.conf file, and i tried to edit it manually, changing its
I want to enable the desktop effects (such as smooth minimising, smooth viewport switching, etc) but it says that "Desktop effects are not supported on your current hardware / configuration. Would you like to activate them anyway?"
My first question is how do I check to make sure whether the NVIDIA drivers are enabled or not? (I know they're on the system, since 'NVIDIA X Server Settings' is in the list of applications).
My second question is how do I activate these drivers?
Note that I don't have root access, since I'm using a university machine, so I can't edit the xorg.conf or anything like that.
I've set up a basic 11.4 server/workstation at my home and am having trouble post-nvidia install when it comes to dual-monitors and compositing. Now, I've looked at many posts here and have not found an answer, since most of the answers are obviously for single-monitor setups. The reason I think this is that all the solutions render my second monitor useless (ie, blackscreen/does not function).
Background: I've set up the nvidia 275 drivers via blacklisting neauveau(sorry if I have misspelled) and installing the package [nvidia drivers] from the nvidia website. Everything works great, the login screen comes up on the correct monitor! (I'm quite excited about this, for Ubuntu it took a startup script which, for some reason, rendered full-screen quakelive across two screens instead of one. It was win-lose).
The error I'm getting in the configuration utility for KDE is that compositing is not available because the extensions XComposite and XDamage are not available. These are available and effects work fine if I disable my second monitor. How can I enable for two?
Here's my xorg.conf. I've tried removing this and restarting KDE without and this disables my second monitor, but allows for compositing as mentioned before.
Like a guy earlier today report a problem with Opensuse 11.2 working fine on his machine but 11.3 is not. I have somewhat the same problem. The default installation freezes randomly. I have seen this error before with Intel video cards but never with NVIDIA. Right now, I'm using VESA in failsafe mode and trying to install some drivers from this repo.
I'll try and find a fix for this. (Hope their is one)BTW, can anyone confirm when the official drivers for NVIDIA cards are coming out?
Basically everything was going fine, and i was enjoying the OpenSuse experience, then downloaded djl (Games Launcher) , installed some games and found that i had a very very very bad frame rate (about 1FPS), and my GPU is a NVIDIA GTS250 (1GB), and runs most games flawlessly under m$, so i went about installing the graphics drivers for my card. I followed the instructions and was under the assumption that i installed the correct ones, but now i cannot boot into any graphical interface. I think that it should be a graphics issue, as this was one of the few things done before rebooting. I have tried booting into the normal mode, and the failsafe, I have read many other "Not booting'' posts, and have tried their solutions without success, there include: Changing the boot parameters Logging in and manually trying to boot up the gui (init 3.... init 5... etc)
When the computer tries to load up OpenSuse in normal mode, it comes up with the normal loading screen, and then about 90% of the way it stops for about 30 seconds, and then switches over to a CLI, asking for a login, going through the log a couple of things fail, did have these noted down (but cannot find and will post along with other commands that i am asked to do) I want to try and avoid a reinstall as it took me a long time to get the WiFi card working.
I've recently jump from the Ubuntu/Mint ship, and figured I've give a polished KDE distribution a shot. Of course I turned to OpenSuSE, and I love it so far. I've resisted KDE quite a lot since 4.x came out but it's really come along. Much better than the (in my opinion) monstrous disaster that Gnome has become.
Anyways, on to my problem: I've installed the proprietary Nvidia drivers via the one-click-install shown in the wiki, and that worked great. But now my resolution at boot - that is the boot/loading screen, not my desktop - is shown at a very low resolution instead of my native resolution, like it was with OpenSuSE's default open-source Nvidia driver, which I'm guessing is Nouveau. On Ubuntu, this was pretty easy to correct; all you had to do was edit /etc/default/grub and put your resolution there, and tinker with some other options so that instead of Plymouth trying to set its own, it just carries over Grub's specified resolution. But I can't seem to do that with OpenSuSE. For one, I don't see /etc/default/grub, and more than that, I don't think you guys use Plymouth. I could be wrong on that second point, though. So, how can I change the boot screen's resolution to my native resolution? I'm using the latest Stable release (11.4) and latest Nvidia drivers. Other than that, the install is new.
The PC is a Toshiba laptop model# x205-s9359 running 11.2, KDE 4.3.5. Its video card is an nVidia 8700 GT. For two years now I've been plagued by random flashes, flickers and even missing scan lines on my screen when I use the nVidia drivers (up to and including 195.36.15), so lately I've been using the nv drivers. I miss the effects, etc. but I can live with that. At least I can get my work done, even if the display isn't as fancy as I'd like.
- When I run the nv drivers I can't suspend the PC to RAM or Disk. This means a lot of wasted time waiting for the machine to shut down and reboot every time I leave my desk for any length of time. If I try to suspend to RAM the only thing that happens is that the network connection disconnects then reconnects immediately. Here's the log file.... - If I try to suspend to Disk the PC appears to suspend as expected, but when it resumes it hangs before restarting X, and there's no keyboard or power button response. I have to use alt-prtsc-reisub to reboot. When the reboot is complete the screen shows all the windows, etc that were present before the suspend. Here's that log file.... -When I run the nVidia drivers the suspend/resume functions work perfectly, but I have to put up with all the problems described above. Here's the log file for Suspend to RAM with nVidia, and here's the one for Suspend to Disk.
I've spent hours searching for clues in these forums, on the openSUSE.org site in general, at KDE.org and with Google and I'm sorry to say that most of I've found is horribly out of date, and/or it's way over my head. or (worst of all) not even dated, so I've no idea whether it's current info relevant to my situation or so out of date that I might do real harm if I were to trust it. (RANT: Is it too hard to put a date on an article?... end of RANT) I'd be quite content to use the nv drivers if I could solve the power management issues, but I'd be equally happy to solve the flickering etc. with nVidia drivers.
I am new to opensuse and have installed 11.2 KDE. It is simply perfect for my system. However after the initial setup the display resolution was set perfectly fine for my 18.5" LED monitor, default resolution was 1366x768, and everything looked good from desktop to fonts but the OSS drivers didn't support compositing so I decided to switch to nvidia drivers. I installed the driver as shown in openSUSE repositories page, for my 6600GT card. Now after rebooting everything is stretched,even the fonts look really ugly and fuzzy.
I am unable to find any mode in Nvidia XServer settings that would correct the current ugly stretched display. I am unable to set 1366x768 manually as well, doing so my PC won't boot to KDM but rather sticks to console. Now it's for sure that my monitor and display card supports 1366x768 resolution but it's just that nvidia drivers/Nvidia XServer settings won't let me set that resolution. How can I set the resolution or even better if I can enable compositing using OSS drivers then that would be great an dm willing to switch back.
I recently used Yast to update drivers for my Quadro NVS 290 card. When I did this Yast informed me that my current kernel (2.6.27.54-0.1.1) was incompatible with the latest version of the Nvidia driver, but that the Nvidia drivers could be installed if the kernel was replaced with version 2.6.27.7-9.1. I chose this option (there was a good reason for doing this I swear), but since then, the x server refuses to start using the Nvidia drivers; boot ends at the command line. I've tried obvious things like reinstalling the drivers, but this doesn't change anything. If I try starting sa2 from the command line with, it fails to start and refers me to sax.log. I look at this, and the relevant part of the log seems to be this:
(II) Loading /usr/lib64/xorg/modules/updates//drivers/nvidia_drv.so (II) Module nvidia: vendor="NVIDIA Corporation" compiled for 4.0.2, module version = 1.0.0 Module class: X.Org Video Driver
It's been mentioned several times in this forum already that downgrading to NVIDIA driver version 256.53 can solve random-seeming plasma crashes (the error dialog box usually mentions a "floating point error").So, I upgraded openSUSE 11.3 to KDE 4.5.5 today and couldn't add a clock - any clock - to my desktop or panel without a plasma crash. I had been using the latest NVIDIA kernel modules (v260.19) from the openSUSE NVIDIA repo. I uninstalled them, installed the gcc, make, and kernel-devel packages, and manually installed the latest NVIDIA driver (270.18). No joy; same crash. So I installed version 256.53. And...it solved the problem.
So, to underscore the point, if you have a recent NVIDIA card and you're having random plasma widget crashes, try downgrading your NVIDIA driver.
This is my first time with openSuse as I have heard that openSuse is better forlaptops then ubuntu is. On this laptop, I had already installed ubuntu but decided I no longer liked ubuntu very much, but for no real reason. I encountered almost the exact same problem using both ubuntu and kubuntu, but I had more problems on top of the graphical problem - so I decided to give openSuse a try. I love it so far!Anyway, to the point - I have an Nvidia GeForce GT330M. I have tried installing the drivers the "easy way" and the "hard way" and I have even used the script lnvhw, all to no avail.
What seems to happen is that, after I install the drivers (from runlevel 3, of course), as soon as I restart my computer it initially loads just fine. However, after the loading bar shows up, I get dropped into a console login (tty1), and tty7 & 8 show absolutely nothing, except a blinking cursor.I have two graphic cards in my computer -- an Intel HD card. This is loaded normally and, from "My Computer" it is the graphics card in use, as far as I can tell. The other, as I said, is the nVidia GeForce GT 330M. I'm not much of a "power" user, so I'm not really sure where to start with finding the issue
