Networking :: Public Static Ip Routing ?
Jun 14, 2011
I've been trying to get it work for 2 days now..
Here's my setup.
MODEM -> router (ISP one don't have access)
from the router it split into 2 connection one to my GW (linux debian) and another to a switch which is connected to a web/email server and the gateway.
My gw use x.x.x.27 and x.x.x.26 (everything I use on these ips is ok)
on the web/email server I have x.x.x.28 29 and 30
With this setup it's ok but I want to eliminate the link to the switch and make it pass thru the GW and i can't manage to get it work!
View 4 Replies
ADVERTISEMENT
Apr 14, 2009
I have just installed Fedora 10 on an old laptop and was quite impressed with how smoothly it all went ... until it came to setting up networking!
I have battled for three days now and I'm almost there;
- installed updated firmware to the built in Broadcom 4306 wireless network adapter
- got NetworkManager to work with a static ip address by manually editing the ifcfg-wlan0 file
- managed to get the WPA security to work
The only problem I am left with is that there is no default route; if I set one up using: ip r a default via 10.1.1.1 dev wlan0
Then everything starts working.
If I try to add routes using the NetworkManager gui interface they dont get saved (no suprises there then! ).
I have tried creating a route-wlan0 file in /etc/sysconfig/network-scripts/ but this seems to be ignored by NetworkManager.
Since the NetworkManager GUI is almost useless, does anyone know if there are any other configuration files I can manually modify to get a default route set?
View 6 Replies
View Related
Nov 29, 2010
I have to connect my private adres 10.0.0.2/26 to an external adres 192.168.1.253/16
I am not allowed to use Nat so i have to create a static routing table..
Ive put a router between with 2 nic's:
Ive seen on various sites that :
Should do the trick but it isnt working for me ... Ipforwarding is enabled.. Also when i use the sys/proc command..
How to make the table? I am using Opensuse 11.2
View 5 Replies
View Related
Aug 25, 2010
In configuring static routing between two different subnets.
I have two different subnets as mentioned below:
I have a linux machine with two NICs on which i would like to configure static routing. details of the NICs are as mentioned below:
I have configured the gateway as 10.77.77.1 on machines which fall under 10.77.77.0/24 subnet and 172.16.40.1 on 172.16.40.0/24 machines.
My main motive here is i want communication to happen between both the subnets.
If the following modifications to route-eth0 and route-eth1.
View 3 Replies
View Related
Dec 16, 2010
I have a block of 5 static ip's and 2 servers that push HTTP and other services. What is the best method of configuring/routing traffic to individual boxes on the network?
More detail: One of my static IP's is assigned to a dedicated box for an Ubuntu mirror. Another static IP is assigned to a server with all of the HTTP traffic.
Several configurations function to route traffic appropriately (forwarding proxy or 1-to-1 NAT). However, with 1-to-1 NAT, the box is left open to the world with only the software firewall. Do I really need to place a hardware firewall inline to EVERY server?
Or, what other methods of routing and firewall would you recommend?
View 3 Replies
View Related
Jul 19, 2011
How would you assign a server a public static IP ?
Ok.. I guess to better ask my question... how to assign server public static IP centos? Like for example I am in the router itself.. where would I go to point ip 44.33.33.21. to ?> 192.168.1.4
What would be the most common in the routers?
View 7 Replies
View Related
Jul 23, 2011
I am running a modem in bridge mode to my server
I edit file /etc/sysconfig/network-scripts/ifcfg-eth0 code...
I do service network restart and get nothing ? No connection... Are there other files I need to edit?
View 12 Replies
View Related
Aug 12, 2010
How to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
In the section
You can see that the routers Local-router1 and 2 has the same dialling plan.
What happens is the gatekeeper send calls randomly to one router or to the other when one of the matching extension is dialled.
What I am trying to do is to force
Any calls coming from Remote1 to go out only throught Local-router1
Remote1 =========================> Local-router1
And any calls from Remote2 to go out throught Local-router2
Remote2 =========================> Local-router2
View 1 Replies
View Related
Apr 6, 2010
I have a firewall, this consists of three NIC's:
Code: eth0[192.168.0.2] eth1[192.168.1.2] and eth2[10.10.165.2]
I am trying to ping eth0 from eth2, but I am not able to succesfully get a response from pinging the device, I am using:
Code: ping 192.168.0.2 -I eth2
I have tried to insert routing data into the routing table, but it still doesn't work
View 2 Replies
View Related
Apr 26, 2010
I got this message on Friday from just one domain. uote:mailsrv.forthnet.gr #<mailsrv.forthnet.gr #5.5.0 smtp; 554 5.5.0 Your message was considered to be spam by the FORTHnet Antispamming Policy and was not delivered to the recipient. The following spam tests returned positive for this message:FORGED_RCVD_HELO,RCVD_IN_BRBL. For further information visitWe are not a spamming community but it seems we have a statice IP address that has a Reverse lookup to "myipaddress.static.lyse.net" and not my email domain. Would setting a cname mail.mydomain.no -> myipaddress.static.lyse.net cure this problem or are there more tricks to be performedOnce I have cured the FORGED_RCVD_HELO I can move to getting the IP removed from BARACUDA.
View 2 Replies
View Related
Aug 2, 2011
I'm trying to write a p2p file sharing program using python's built-in libraries. Everything is going well. The only thing is that i'd like to be able to use openssl public and private keys so only a host with the public key could access/decrypt the filesharing. I've gotten these libraries (httplib, basehttpserver, ssl, os) to work using just a pem file containing both the public and private keys but no success with them seperately. Can someone point me in the right direction or offer an alternative? PS, the goal of the project is to create an anonymous, decentralized, secure file sharing program. I want to be able to upload this to sourceforge so everyone can use it, if that's any incentive
View 2 Replies
View Related
Sep 24, 2010
I run the following file with the >log.log redirector and it does not capture errors.
#!/bin/bash
echo ************************BEGIN LOG******************************
date +"%m/%d/%Y %H:%M:%S $HOSTNAME"
cp -f /scripts/original/clamscans.log /scripts
[code]....
The following errors show up when I run from the file from the term window, but are not written to log.log:
tar: /public/public/clamscans/*.txt: Cannot stat: No such file or directory
tar: Error exit delayed from previous errors
mv: cannot stat `/public/public/clamscans/*.txt': No such file or directory
I know with windows you can add the 2>&1 to capture error data. Is there such a thing for Linux?
View 2 Replies
View Related
Jun 8, 2010
i know exactly what i need to do, im just not familiar enough with command line to do it properly.i have 7 computers.the first 4 are connected to a router via wireless at one end of the house. of the last 3 only 1 will be able to access the router via wireless, so it needs to share it's one wireless connection via ethernet. this computer i'm going to call 'server'server will have two IP'swlan0 192.168.1.6 this connects to the router that has internet access.eth0 i intend to have the following settingsip:192.168.0.1sub: 255.255.0eth0 will connect to a second router, where the cat5 cable goes from the server, into the internet port of the router where i will define the router's static IP:IP: 192.168.0.100sub: 255.255.255.0gateway 192.168.0.1i have then set the router IP for LAN handling as 192.168.27.1 and all ethernet connections will have a 192.168.27.x IP.
so i need to know how to, without a gui application, use the terminal to assign server eth0 a proper IP address, and tell the server to take the connection it has and share it through eth0 to supply internet for the last 2 computers via ethernet.i had it set up in this way with a windows machine being the one that had the wifi access, but i'd rather have it setup for the ubuntu server to do this task. security is imperative for these 3 remaining machines, so just getting 2 more wifi adapters for a connection to the initial router isn't an option.the 2 that connect to server do so through SSH and though server IS connected via wireless it only makes outward connections through
View 1 Replies
View Related
Mar 3, 2010
How can I forward all traffic from a public IP to another public IP. Let's say I have a first debian box named box1 with eth0 = 1.1.1.1 and eth0:1 = 1.1.1.2 and I want to forward all traffic from 1.1.1.2 to "box2" located somewhere else over the internet and having for eth0 2.2.2.2 Both 1.1.1.0/24 and 3.3.3.0/24 are public IP ranges.
View 1 Replies
View Related
Sep 6, 2010
My setup is...I have a wireless access point using laptop as a gateway. The AP is also connected to a switch as is the laptop. So the laptop has two interfaces one wireless and one wired. A third device is using the AP to connect to a server on the internet. The AP sends the packets to my laptop where they are dropped. I've been looking for a solution to this problem without success. Basically is there a way for my laptop to forward all packets it sees from a certain IP address to whatever destination address they have?To clarify, my laptop is just the gateway of the AP and none of the packets are addressed to it at all, it just picks them up using a sniffer or similar tool.
View 1 Replies
View Related
Mar 10, 2011
I have a pc with debian 6 (without GUI) installed on it and want to use it as server at home. It has 2 ethernet nics. Now i want to configure the routing process. Searched internet for a long time found something but couldn't get it work.
View 8 Replies
View Related
Feb 17, 2010
When setting up an SSH proxy, I know you can configure Firefox to route DNS requests through the proxy. Is this possible from linux directly? I'm trying to use wget through the proxy, including DNS lookups.
View 3 Replies
View Related
Jun 26, 2010
I have two subnets which I am interested in connecting.
Some basic network details:
Subnet A:
Subnet B:
I am trying to think of any further relevant details, but that seems to be it to me. If I forgot anything, please tell me.
Ok the question. WHAT do I type? (Explicitly!) And WHERE do I type it? In order to reach ubuntu-01.tec.lan, or ubuntu-02.tec.lan from perpetrator.tec.lan or rapine.tec.lan?
I'm interested in using actuall ROUTES. I can already achieve results similair to this with either a NAT firewall, or with VPN.. but that's not what I am interested in.
From what I have found out so far, I should need something like the following:
On Gateway 1B:
Code:
And on Gateway 1A:
Code:
View 5 Replies
View Related
May 14, 2010
I'm newbie to Wireless. Currently I try to implement EAP-TLS but firstly I need to get the hardware work, allow Access Point to Route from Wireless to Wire (LAN DNS server).
View 4 Replies
View Related
Apr 22, 2010
I am having some trouble setting up routing on my Ubuntu 9.10 Server. I have the GUI installed with Webmin and OpenVPN Heres the setup :
1 NIC - WAN - eth0 - IP: 146.231.x.x SUBNET: 255.255.252.0
1 NIC - LAN - eth1 - IP: 192.168.1.1 SUBNET: 255.255.255.0
1 NIC - ADSL - eth2 - dynamic
What I need to do is the following.
All users are connected to the LAN.
All requests for IP range "146.231.x.x", and "domain.com" need to be routed from LAN (eth1) to WAN (eth0).
All other internet requests need to be routed to ADSL (eth2).
-> I have the masquerading in the linux firewall working for NAT, but all traffic goes to ADSL (eth2).
-> I am using OPEN-VPN over the ADSL also.
-> DHCP and DNS work fine.
I also need all ports opened with the route (from eth1 to eth0)
View 1 Replies
View Related
Mar 3, 2009
I want to use tab networking in my kvm with routing.Can any one guide me how i can do it. i have been reading different guides over the net but not understand any one clearly.I have read this[URL].. One problem is this all my server are remote and no gui is running.I am able to install kvm with ssh console with -nographic and -x "console=ttyS0" option now i want to change from bridging to tap networking with routing.And i have live ip on kvm guest/Virtual machine.
View 1 Replies
View Related
Feb 20, 2010
IN LAN default GW box I have a routing rule of 172.17.1.0 192.168.180.100 255.255.255.0 UG 0 0 0 eth3 that sends packets matching 172.17.1.0/24 to eth3 etc. When I ping 172.17.1.50 - it goes correctly when ping is issued in the same box (LAN GW) - falls through to default rule when the ping is done in LAN's boxes i.e. it goes to the LAN GW box and then to Internet incorrectly instead of going to eth3 and 192.168.180.100.
Is there any way of seeing why the packet matches or not the routing rules?
View 14 Replies
View Related
Feb 16, 2011
I have a network routing problem that I need to fix using a PC with ubuntu installed.
Here are the details of my problem:
- I have two networks.
- The first network is an ADSL router with subnet 192.168.1.x. I do not have access to the router nor change any of its configuration.
- The second network has a subnet 172.26.x.x and connect via a wireless access point. Some of the devices connected to the network require to have static IPs.
- I have a PC with ubuntu installed and two ethernet cards: one connected to the first network and the other connected to the access point.
- I need to share the internet connection between the two networks using ubuntu. I already tried before on windows and the sharing worked when both networks were configured to use the same subnet. Once I changed the subnet of the second network, internet sharing stopped working.
View 1 Replies
View Related
Sep 3, 2010
Im having a issue with routing internet traffic from my router two different subnets (vlans).
Theres my setup:-
Server:
Both eth0,1 are running dhcp (two scoopes) that works fine!
The output of route -n is:
I have ip_forwarding on aswell, but i can ping the ip on the server running that dhcp scoope ie ping 192.168.4.1 works great but i just cant get the internet on the clients.
View 8 Replies
View Related
Feb 24, 2011
I have two linux boxes running RHEL 5.5 with internal ip addresses 10.0.0.114/24 and 10.0.0.118/24, and usual gateway 10.0.0.1. There's an apache listening on both ports 80 and 443 for several websites. This works nice, but the feature for load balancing has to be added. For this, externally, but in the same subnet, a hardware device has been placed for load balancing (we call it "F5"), with internal ip 10.0.0.152 (vrrp for 10.0.0.153 and 10.0.0.154). There's a service address that does NAT via round robin to the servers, 10.0.0.208, managed by the F5 balancer.
If I set as gateway the ip 10.0.0.152 in both nodes, I can use the service address for browsing http and https, *BUT* at a cost that ssh and any other connections, at OS logging level, come from 10.0.0.1, which is innaceptable (i.e., I can' set proper security, regardless the F5 is badly configured), so I have to find another way for this. So, I thought of using iptables mangling capabilities, and my thought is that just changing the default route of the incoming http(s) traffic, everything should be ok. I've done the following:
- Create a table called "F5":
# cat /etc/iproute2/rt_tables
[...]
#1 inr.ruhep
#
[code]....
If I tweak the hosts file in my M$ workstation to test individual access for each server, I can browse the websites with no problem, but if I set the service IP address, I get an error "Document contains no data" in the browser after just a few seconds. Apache logs show nothing in its logs. I can see packets arriving, but seem to go in a loop. I can provide some output, but since surely I'm making some mistake in the process, if I get help with the proper knoweledge about how to fix it, the problem will be solved. But if still someone needs it, I can provide more data.
View 5 Replies
View Related
Apr 5, 2010
After making an changes (add/modify/delete) to /etc/static.routes, what command should we use to reload the routing table?
View 5 Replies
View Related
Nov 28, 2010
At every site i have two provider vsat and wireless connection.I have a linux machine and wanna setup act router for every site.
SITE 1 :
vsat : gw 10.23.128.1
wireless : gw 192.168.100.1
[code].....
View 5 Replies
View Related
Oct 6, 2010
I am sharing my DSL internet connection using a modem+wireless router (single device) to 5 systems. I want all my internet traffic to go through one of the linux boxes in my network.
The problem here is that wireless devices connect directly to the modem+wireless router.
Is such routing of traffic possible??
PS: I am not sure if i could convey my situation clearly...
View 2 Replies
View Related
Aug 2, 2010
I'm trying to work out how to route all traffic destined for the internet from all devices connected to eth0 to a wireless router access point via wlan0 on my Slackware box. I also have dhcpd providing ip addresses on the same subnet to any device connected to both eth0 and wlan0.
Diagram:
Code:
____________ ____________
[ ]=============> (wifi) ==============>[ Router / ]
|Workstations| __________ |Access Point| 192.168.2.1
[____________]==>(eth0)==>[ ]<==(wlan0)==>[____________]
192.168.2.253| Server |192.168.2.254
[__________]
If I connect to the router/access point via wireless or directly to the Server via a crossover cable I can obtain an ip address from dhcpd, so that works. As far as I can see I just need to how to route between eth0 and wlan0 then I can provide internet access to those devices!
ifconfig:
Code:
eth0 Link encap:Ethernet HWaddr **:**:**:**:**:**
inet addr:192.168.2.253 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::201:2eff:fe27:aea3/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
[code].....
View 10 Replies
View Related
Dec 17, 2010
I've been trying to setup an IPSec connection between two routers, but am having trouble with the actual packet routing.
My setup currently is two local networks (192.168.1.0/24[netLANA] and 192.168.0.0/24[netLANB]) that are connected to their own routers (192.168.1.1 and 192.168.0.1 respectively). The routers are both connected to the 194.26.1.0/24[netWAN] network. I wish to setup an IPSec connection between the two routers, to act in tunnel mode between the two local networks.
The first router is a linux box (on the netLANA network) that I am setting up using the ipsec-tools, and the other is a Netgear ProSafe FVS318G (on the netLANB). I've set them both up to have the same configuration for IPSec. Also, on the linux router I have setup a route like this:
Code:
$ route add -net 192.168.1.0/24 wlan0
So that all traffic destined for the netLANB network will be routed to the wlan0 interface (netWAN in this case, and therefore over the tunnel).
My problem is that if I ping from any host on netLANA, I can see the ICMP reply comes back to the linux router, but it doesn't get back to the original host.
From the linux router, here is the tcpdump of the ping:
Code:
$ tcpdump -n -S -i any
17:06:26.308353 IP 192.168.0.5 > 192.168.1.4: ICMP echo request, id 1036, seq 1, length 64
17:06:26.308780 IP 194.16.1.6 > 194.16.1.5: ESP(spi=0x0ea08914,seq=0x2f), length 116
17:06:26.316287 IP 194.16.1.5 > 194.16.1.6: ESP(spi=0x0be1036c,seq=0x2f), length 116
17:06:26.316287 IP 192.168.1.4 > 192.168.0.5: ICMP echo reply, id 1036, seq 1, length 64
[Code]....
View 2 Replies
View Related
