Networking :: Bad Exit Status When Attempting To Build Netxtreme Network Card Driver?
Mar 9, 2011
I am having a terrible time getting any networking to work with a new RedHat Enterprise 6 64 bit install. I am installing on an HP Proliant DL380G7.I have downloaded the driver - hp-netxtreme2-6.2.23-2.src.rpm from the HP website.Followed directions and did the following:1.Build Environment Setup - installed redhat-rpm-config and kernel-devel2.Installed the source (hp-netxtreme) rpm.3. Build the Binary RPM - installed rpm-build and ran the following:rpmbuild -bb /root/rpmbuild/SPECS/hp-netxtreme2.specIt runs through the build process and near the end I get the following:make -C /lib/modules/2.6.3271.el6.x86_64/build UBDIRS=/root/rpmbuild/BUILD/hpnetxtreme26.2.23/obj/default/bnx2-2.0.23b/src modulesexpr: syntax erromake[2]: Entering directory '/usr/src/kernels/2.6.32-71.el6.x86_64'/usr/src/kernels/2.6.32-1.el6.x86_64/arch/x86/makefile:81: stack protector enabled but no compiler supportmake[2]: gcc: command not found
make [3]: ***[/root/rpmbuild/BUILD/hp-netxtreme2-6.2.23/obj/default/bnx2-2.0.23b/src/bnx2.o] Error 127make[2]: ***[_module_/root/rpmbuild/BUILD/hp-netxtreme2-6.2.23/obj/default/bnx2-2.0.23b/src] Error 2make[2]: Leaving directory '/usr/src/kernels/2.6.32-71.el6.x86_64'
[code].....
View 2 Replies
ADVERTISEMENT
Jan 29, 2011
I have a Broadcom Corporation NetXtreme BCM5721 network card on my server at work.Everything works fine for a few weeks, then randomly the network connection on the server will stop working. After it stops working, I will try to reconnect with the network manager, it shows a wired connection available, it shows the "connection in progress"animation, then the "connection disabled" icon.
I uninstalled the network manager and used manual configuration, but do you think the network manager was the issue? I can't have the server disconnecting randomly every few weeks with no way to know what the real problem is. Was there an issue with the network manager with 10.04?
View 4 Replies
View Related
Jun 24, 2011
I'm trying to configure my network card using the b43 driver. I'm running 10.04.2 on the kernel version 2.6.35-25-generic-pae.
Surprisingly, I was able to connect to my home wireless network using the b43 driver without a problem. The only issue is that it doesn't automatically connect. I have to use the following command in order to get it to work:
Code:
After typing my password, I wait for 10 seconds and am automatically connected. My question is, how do I configure my system to do this for me permanently (or at least automatically) so I don't have to type it every time I log on?
View 8 Replies
View Related
Dec 22, 2009
I have a Netgear WG511GE PCMCIA card, and a driver from the original installation disk. I used an ndiswrapper-utils gui called ndisgtk to install the driver. I then do the following to verify an installation:
[Code]....
Unfortunately, when I put the PCMCIA card in, nothing happens. On Windows, a green light flashes even if the card is not connected to any network. At first I thought this might be a hardware issue, so I did #lspci and got:
[Code]....
Lo and behold, when I put a different unbranded Wireless PC Card in it works. I'm no expert in Networks, but to me this suggests a driver problem (i.e. the card is physically detected it just won't work). However, the correct driver was installed with ndisgtk and this was verified with #ndiswrapper -l, hence the confusion.
I'd be grateful if anyone else has had this problem/knows of this problem and is willing to share the solution with me/point me in the right direction. So far, Google has returned a few posts from a few years ago talking about patching kernels and manually building files etc (just before Prism54 became integrated into the Linux kernel).
View 8 Replies
View Related
Sep 8, 2009
I just recently installed CentOS 5.3 and to make a long story short I found the entry for my wireless card under the network settings but when attempting to activate the card the system locks up. I have to reboot at that point as nothing responds (keyboard, mouse, etc..).
Running the command /sbin/lspci -v reveals the following about the wireless card:
01:00.0 Ethernet controller: Realtek Smeiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller (rev 20)
View 3 Replies
View Related
Feb 13, 2010
I recently installed Ubuntu 9.10 on an old family laptop. It is a Compaq Presario V2000. Everything works perfectly except no wireless networks are recognized, even though I know there are available networks. My network controller is detected but is not doing it's job, which is finding available wireless networks! Using "system testing" I found this out about my network controller:
"Detecting your network controller(s):
Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)"
url
View 3 Replies
View Related
Sep 1, 2010
I'm setting up an LTSP server using Ubuntu 10.4 64bit, and PXE connecting with thin clients using Atheros cards. The ltsp environment is 32bit.
Unfortunately I get an error message with "No interfaces found! Aborting..." and a kernel panic early during PXE boot.
After an enormous amount of investigation, I've narrowed it down to (probably) being the fact that the ltsp chroot environment doesn't have the correct driver for my network card (I believe it's atl1c). The correct driver IS available in Ubuntu, though, as I can successfully boot the thin client from both 64bit and 32bit live CDs and bring up the network interface.
how can I install the correct driver in the PXE environment?
View 2 Replies
View Related
Jul 4, 2011
I installed newest Ubuntu system, 11.04, Natty-Narwhal, and PC is running smoothly. It is solid machine, Celeron 430, 1 gb of DDR2 memory and I have both LAN card and graphics integrated on the mobo which is MSI 7529, based on G31/P35/P31 chipset.
I plugged lan cable directly from my PC to the ADSL router. There is another Win Xp machine on the same router and it has connection, and internet is working fine. Right now Im writing from the Win 7 laptop, which is connected to the same router via wifi link... all working like a charm...
But, when I plug the Ubuntu desk I cannot get access to bot lan and internet...
I searched the net and it seems that ubuntu didnt install proper driver during the OS installation. Here are some diagnostics of the current config and state:
Code:
Module Size Used by
binfmt_misc 13213 1
snd_hda_codec_realtek 255820 1
code....
As you can see I need to install driver named r8101 instead this one r8169 and I think it will work that way. I found driver here only problem is dont know how to replace them.
View 9 Replies
View Related
Apr 23, 2010
I was installing SMPLAYER when the power failed...now i get this error message when trying to re-install the packages..
E: liblzo2-2: subprocess installed post-installation script returned error exit status 2
E: mplayer-nogui: dependency problems - leaving unconfigured
E: mplayer: dependency problems - leaving unconfigured
[code]....
View 3 Replies
View Related
Jul 20, 2010
I just installed Linux Mint 9 as a dual boot install with Win XP. Trying to activate wireless network card driver and video driver. Pops up: "You are not authorized to perform this action".How do I get authorized?
Now every time I boot Win XP, the Internet Explorer menu bar is all blacked out and goofy. If I log out and back in it corrects itself. If I reboot it's blacked out again. Re-installed IE8. Still blacks out.Also Firefox in Win XP crashes expectantly. It has NEVER crashed on me previously.
View 9 Replies
View Related
Jan 26, 2011
I'm getting the following output when trying to compile my cpp project:
Code:
"/usr/bin/make" -f nbproject/Makefile-Debug.mk QMAKE= SUBPROJECTS= .build-conf
make[1]: Entering directory `/home/walther/NetBeansProjects/CppPlay'
"/usr/bin/make" -f nbproject/Makefile-Debug.mk dist/Debug/GNU-Linux-x86/cppplay
[Code].....
I've seen you guys replying to others about this collect2 error, but all of them had some kind of informative message from the compiler.
View 1 Replies
View Related
May 7, 2011
Can't boot into Ubuntu. Using recovery mode, I get fsck exit with status 3 error. I did man on fsck and there is no reference to status 3. Same issue as [URL]
I have my data on sdb3 which is having this issue. File system is ext4. I can't go into shell or anything, I get the fsck error and the system reboots right away and stuck in that loop.
View 5 Replies
View Related
Jun 10, 2010
I am running a command pretty similar to the one below:
Code:
I need to capture the exit status of that part of the command.
What I am trying to do is set a variable that can be modified within my_job.sh, and used to exit.
However, no matter what I set "status" to in my_job.sh, it exits with "0".
What can I do differently?
View 3 Replies
View Related
Mar 3, 2010
How exactly can I use the exit status of a command in an if statement ?
Something like this:
Code:
View 3 Replies
View Related
Feb 19, 2010
command will just execute and exit with a status of "0" -"Every command returns an exit status (sometimes referred to as a return status ). A successful command returns a 0, while an unsuccessful one returns a non-zero value that usually may be interpreted as an error code. Well-behaved UNIX commands, programs, and utilities return a 0 exit code upon successful completion, though there are some exceptions."[URL]With the command . . .
Code:
# dosfsck -v /dev/sdb
it could be very helpful (and decide my next move) to see the exit code as 0, 1, or 2 . the man page suggests the command exit code will specify if the message I get - "Cluster size is zero" (I think it is a "1")is a recoverable or fixable error by the utility. or is non-recoverable - a pretty nifty feature if I understand this right. [URL] is there anything like this script COMMAND_LAST used in the following link. [URL] that can be entered in the terminal window after - or at end of - my dosfsck command or any command. just to see if it has a 0, 1, or 2 status ?
View 2 Replies
View Related
Apr 4, 2010
I am making a project learning about inheritance and polymorphism
it consists of
Account.h
Account.cpp
[code]....
View 2 Replies
View Related
May 4, 2010
I'm running Ubuntu 9.10 Karmic and XBMC Live.I get error messages which seem to relate to openvpn.So I tried to remove it with the remove command. This is what I getQuote:
@XBMCLive:/home$ sudo apt-get remove openvpn
Reading package lists... Done
Building dependency tree
[code]....
View 1 Replies
View Related
Jun 28, 2010
"E: backuppc: subprocess installed post-installation script returned error exit status 1"whenever I upgrade my system I get the above message Anyone know how to fix it? or if it's anything important ?
View 1 Replies
View Related
Jul 20, 2010
I am trying to extract a .tgz file. I have used the command tar - xvwzf filename.tar but I get the following error:
gzip: stdin: decompression OK, trailing garbage ignored
tar: Child returned status 2
tar: Exiting with failure status due to previous errors
root@test:/datastore/Newfolder# tar -xvwzf filename.tgz
View 9 Replies
View Related
May 14, 2011
I'm trying to make a fresh install on my desktop computer and I got this error on boot:
Code:
udevd-work[155]: '/sbin/modprobe -bv pci:<followed by some numbers>'
unexpected exit with status 0x0009 and it stuck there.
Note that I'm trying to install from a usb stick.
View 9 Replies
View Related
Jan 17, 2011
I have CentOS 5.5 x64 here and I've been trying to build this RPM but I have found no way to get passed this error. RPM build errors: Bad exit status from /var/tmp/rpm-tmp.61655 (%prep)
View 12 Replies
View Related
Sep 12, 2010
I am using a fully updated fedora 13 64-bit system and when i run make on xoscope i get the following error:
collect2: ld returned 1 exit status
I have already installed all of the prereqs. And the configure went without errors.
View 9 Replies
View Related
Apr 10, 2010
I have a scenario where I am executing some child shell scripts in background (using &)through a master parent script.
Is there a way I can capture the exit status of each individual child script after the execution is completed.
View 7 Replies
View Related
Feb 19, 2013
My system has stopped to boot at all...
Code: Select alldone.
Setting parameters of disc: (none).
Setting preliminary keymap...done.
Activating swap...done.
Checking root file system...fsck from util-linux-ng 2.17.2
[Code] ....
An automatic file system check (fsck) of the root filesystem failed. A manual fsck must be performed, then the system restarted. The fsck should be performed in maintenance mode with the root filesystem mounted in read-only mode. ... failed!
The root filesystem is currently mounted in read-only mode. A maintenance shell will now be started. After performing system maintenance, press CONTROL-D to terminate the maintenance shell and restart the system. ... (warning).
Give root password for maintenance
(or type Control-D to continue): _
For now, I just don't know what I should to do next to my system has started to work again...
View 14 Replies
View Related
Mar 9, 2010
it's a hot day and nothing seems to be going right. Trying to figure a way out of this one - error 127. Looks like it could be Metacity problem? There a couple of pythons that also have a problem.
Code:
(Reading database ... 145089 files and directories currently installed.)
Preparing to replace metacity-common 1:2.28.0-0ubuntu1 (using .../metacity-
[code]....
View 5 Replies
View Related
Apr 27, 2010
I have been having the worst time trying to get sametime messenger from IBM to install properly. I had it working fine for the last 6 months and yesterday I accidently updated and it all went to {1134}. I seem to have found dkms to be the source of the problem.
I get an exit 0 regardless of whether or not its install or uninstall. I have managed to get pidgin to work for now, but it is no means ideal for my purposes.
I kept getting this...
rastlosen@rastlosen-laptop:~$ sudo apt-get install sametime-connect
[sudo] password for rastlosen:
Reading package lists... Done
Building dependency tree
[Code]...
View 1 Replies
View Related
Jul 27, 2010
Everytime I install a package or use update manager I get the following message.
Code:
E: linux-image-2.6.32-22-generic: subprocess installed post-installation script returned error exit status 2
E: linux-image-2.6.32-23-generic: subprocess installed post-installation script returned error exit status 2
E: linux-image-2.6.32-24-generic: subprocess installed post-installation script returned error exit status 2
E: linux-image-generic: dependency problems - leaving unconfigured
E: linux-generic: dependency problems - leaving unconfigured
E: linux-headers-2.6.32-22-generic: subprocess installed post-installation script returned error exit status 2
E: linux-headers-2.6.32-23-generic: subprocess installed post-installation script returned error exit status 2
E: linux-headers-2.6.32-24-generic: subprocess installed post-installation script returned error exit status 2
E: linux-headers-generic: dependency problems - leaving unconfigured
The install/upgrade appears to work but I'm getting concerned about the message continuing for so long.
View 2 Replies
View Related
Mar 8, 2011
I'm using ubuntu 10.10 maverick, a package named lmodern is not required by the system, but it can't be remove or purged as follow:
Code:
yurippe@Neptune:~$ sudo apt-get autoremove
Reading package lists... Done
[code]....
View 9 Replies
View Related
Dec 8, 2010
I am preparing everything that I will be using in my fourth year project which is based on the grid computing concept. My problem is that before I installed ubuntu 10.10, I was using 9.10. And in my previous version (9.10) I was able to install condor through the synaptic package manager comfortably,but after upgrading to version 10.10 am getting the following error after installing condor:
"E:condor:subprocess installed post-installation script returned error exit status 127"
View 1 Replies
View Related
Aug 2, 2011
I have a desktop environment with Apache2.(If someone asks why desktop to run Apache2, its because the desktop must display a local website)When I update the html files from a windows box it is being copied in a home/user folder.Cron now has to copy the files with r to the localhost area.sudo cp -R home/myself/Downloads/* /var/www/ works fine:The script containing just that one line is in a file in my /home/myself/Documents folder named: copy_site_localhost.Cron entry in turn was created with the command: sudo crontab -e and the entry is:*/10 * * * * /home/myself/Documents/copy_site_localhostThe error in the syslog file in /var/logs is as follows:
.......CRON[1234] (root) CMD (home/myself/Documents?copy_site_localhost)
.......CRON[1236] error (grandchild #1234 failed with exit status126)
.......CRON{1236] info (No MTA installed, disregarding output)
[code]....
View 1 Replies
View Related
