General :: Windows Xp Failed To Restart After A Power Outage?
Sep 29, 2010
I have thought about it many times but just never found enough guts to attempt using it before..but necessity is the mother of invention so here I am.
I have a Dell PC with windows Xp that failed to restart after a power outage it went into auto restart and caught itself in a loop of restarts and wont see the hard drive so therefore will not start up in windows at all I downloaded feather Linux onto a cd and it does start the PC In Linux but I cant seem to figure out how to find the hard drives in the pc to get the info off of it
View 3 Replies
ADVERTISEMENT
Dec 22, 2009
Installed new APC Back-UPS CS 350 on single server running openSUSE 11.2 64-bit and configured NUT 2.4.1 (SUSE package) according to instructions. When testing, NUT shuts down the server correctly and instructs the UPS to power down. UPS does so after some 20s delay, everything without errors. But after restoring main power, even after waiting for 1/2h UPS does not by itself turn on again, all LEDs are dark. One has to manually press the UPS's power button, which makes server and monitor run again immediately. What could be wrong that prevents UPS from turning itself on again?
Below output of upsc:
[Code]...
View 2 Replies
View Related
Jun 7, 2011
I have a small problem on my Compaq Evo Centos 5.4 web server. The web server runs just fine, the problem is it fails to restart from a power outage. Simple edit the BIOS. No! For a reason I can't think of the keyboard stops working after a few key strokes following the F10 to enter BIOS setup. Then its a power cycle. If left to BOOT the PC and keyboard are fine. After hearing about viruses which get to the BIOS I will ask can NIX get that far so I can adjust the Power ON?
View 4 Replies
View Related
Aug 6, 2010
did an update from ubuntu 8 to 10.04, this has failed. At boot there is initramfs error with prior message saying.
Code:
alert /dev/disk/by-uuid/-the_uuid does not exist dropping to shell (initramfs) I boot to livecd and check disk uuid and compared it to the fstab and it is correct, is there anywhere else this uuid but have been corrupted or any issue that may cause this issue. note there was power cut during upgrade but this occurred when upgrade should have finished.
View 1 Replies
View Related
Jun 21, 2010
I have a slackware 12.2 server. We had some really rough storms this weekend that took the power out for many hours. The UPS that it was connect to gave up the ghost and the server went down hard. I powered up the unit and it some up fine but with no network. Ifconfig -a shows that it only knows about the lo interface. Both integrated gig ethernet ports are missing. I am not a slackware expert. Need to figure out what is needed to get it back on the network. dmesg | grep eth0 shows nothing. Nor eth1. ifconfig eth0 returns no such device.
View 14 Replies
View Related
Aug 7, 2010
My computer is running really slow after a power outage. It was fine, then the power went out. Now it's *unabably* slow. The OS takes a long time to load, the simple calculator takes a few minutes to show up, Firefox doesn't even load at all before I give up. And it won't shut down normally. I have to use the power button.
So did the power outage fry somthing on my PC. Do I have ot replace RAM or the processor? Or is it a software issue? Do I have to do something as drastic as a reimage?
View 6 Replies
View Related
Aug 3, 2010
A 2sec service interruption was enough to cold-crash my PC and its given me a few issues, most I have solved but Synaptic is freezing up. I can get into Synaptic if I go to the terminal and become root with sudo -i If I do it through Gnome it show a frozen-screen version of synaptic like the image I posted with this. Right after the outage (it cold-crashed my PC) I used to get a message box that would pop up when I tried to shut off the PC (I have enclosed images to illustrate) but I have since overcame that problem.
View 3 Replies
View Related
Mar 16, 2011
So the power went out at my house recently, and my home theater PC seems to have taken a blow. We had it on a surge protector, which didn't blow so that's fine, but it keeps telling me its in low graphics mode, and I can't seem to fix it for the life of me. I could reinstall ubuntu, but I have a bunch of movies and music on that drive that I want to keep.
View 3 Replies
View Related
Aug 12, 2011
My computer was on when the power went out. I am not able to boot into ubuntu 11.4 install since that happened. I also have debian 6 and ubuntu 11.10 installed on the same machine and both boot just fine.
The machine boots as normal but stops with the line "disconnected from Plymouth". After the machine just sits there with a blinking cursor. I cannot start another terminal. Is my only option to reinstall.
View 6 Replies
View Related
Jun 7, 2010
After a power outage Ubuntu fails to boot. How can I resolve this ? Is there a safe mode method to resolve the booting problem?
View 8 Replies
View Related
Jun 8, 2010
I recently installed Lynx 10.04 amd64. Twice now, my entire file system has become unusable -- each time after a short power outage (2 seconds).
In the first setup, I had two primary partitions: 1) / that was ext4; 2) /home that was ext4.
In the second setup, I changed the /home to ext3.
Both times, after booting up following the power outage, I received a message saying that "serious errors" were found in /home. But, after several reboots, I was able to login and use the system. Then, some time later, I would started getting "Read Only" messages when trying to write to the file system.
fsck gave the following message: "/home terminated with status 4". I received numerous "I/O error" on sda messages.
My question: Is this vulnerability due to using ext4 or is it related more to something else in Lynx 10.04? Further, what can I do (other than buying a power backup device) to avoid my file system becoming unusable after a power outage?
View 5 Replies
View Related
Jul 14, 2010
I come with questions to try out the wonderful forum support I keep hearing Ubuntu has! I figure this is a convenient time to ask, since I am soon to swap the UPS on my Ubuntu box. This all refers to Ubuntu 9.04. You see, not too long ago, I had a couple of power outages, and suffice to say, despite the efforts of my UPS, I didn't get to shut down my Ubuntu box properly on either occasion. After the first one, when I powered the computer back on it failed to boot. Some googling of the error message led me to find that the UUIDs Ubuntu assigns to things like hard drives, which are not SUPPOSED to change, had in fact changed. From an archived thread here I found out how to find out what the new ones were, and slapped them into my FSTAB hoping that'd be the end of it.
(Partitions/Drives affected: hda2, hdb) It wasn't. Ubuntu came up with new errors to throw at me. This time, it threw the "bad superblock/wrong fs type" error that I'm used to seeing when I fudge a mount command. It appeared to be the same anyway, it went by so fast I couldn't really read it, sure wish the pause button worked. The gui did finally load, but showed no sign of the affected drives.
I found that if I commented out the affected drives in the fstab, they would appear in the gui, ready and mountable and apparently just fine. I've double-checked the UUIDs. The new UUIDs I put in fstab match the new UUIDs that the vol_id command reports. What is wrong with my fstab? Why won't it mount them automatically? (I'll post both versions as an attachment)
Another minor problem is for some reason I can't get privoxy running anymore. I've temporarily taken to running the Windows version in wine. I seem to remember I had a helluva time getting the linux version to work in the first place anyway, so I think I'll just keep running the windows version in wine. Most importantly, what can I do to prevent this happening again? Debian Sarge never gave me such trouble (and my deb box suffered quite a few improper shutdowns too). Ubuntu's based on Debian. What gives?
View 5 Replies
View Related
Feb 10, 2011
I am using ubuntu 9.10. in my area there are frequent power outage. So my wifi get disonnected as the router stops. And it asks for security code. So when power comes the router starts but i have to manually write the security code and connect to wifi again. how i can make the computer to auto connect to wifi after power comes.
View 3 Replies
View Related
Jun 23, 2011
We got a power outage yesterday. When my PC went back on, I noticed the Date and Time display disappeared along with the System Tray. How do I get these back? By the way, I only see the icons for printer, networkmanager and pulseaudio applet on the Taskbar at the bottom.
View 4 Replies
View Related
Feb 10, 2010
When power was restored after an outage, my server (running Ubuntu server 9.10) started back up & got stuck in the GRUB menu ("Version 1.97~beta 4" I think) - it didn't do that countdown & auto-select the top item like I'm used to. Just stayed there, and since the server is headless, I had to dig out my monitor & hook it up to see what was wrong.
View 1 Replies
View Related
Feb 11, 2010
So yesterday, I my power went out on my desktop and when I rebooted, the screen resolution was stuck at 640x480. When I go to the display settings, no other higher options are available. Any suggestions?
View 1 Replies
View Related
Sep 24, 2010
Due to a power outage, my EXT4 file systems (which contain /usr and /opt) no longer mount at boot-up. They are, however, seen by disk utility in Knoppix, so I assume the data is still there and that it's just matter of making a connection to it.
View 6 Replies
View Related
Jan 31, 2010
Sometimes either due to a power outage or due to lightning I turn off my Wimax modem and continue to use my laptop on the battery.Then when I turn the modem back on, there is no internet connection.Here's what I've tried:
1. turn off and on the network connections - right-clicking on the icon on the bar on top of my screen.
2. turn off and on the dsl-provider connection - no effect.
3. When I tried to re-do pppoeconf, it says that there's no response from the concentrator.
This has happened a few times in the past and the only thing I can do to go online again is restart the computer. And it works.Now on Windows, the double-computer icon showing a network indicates connectivity AND data movement. Unfortunately we don't have this on Ubuntu.I'm just after a restart and I'm online now. But I'd like to know if there's a way around this without having to restart.
View 3 Replies
View Related
Oct 10, 2010
I setup a mythbuntu pc with an onboard card (eth0) so I could watch and listen to movies and music stored on my other pc in the basement. Everything worked fine until we had a power outage. I turned on the pc after the outage and had no networking.
I looked and saw no link lights. I verified the network port but plugging in a laptop. I got an ip and able to connect to the internet so the port is not the issue. I plugged in a pci 10/100 card (eth1) and booted up, got link lights, but no networking and not able to even ping the gateway. I setup a static ip in /etc/network/interfaces and added a route to the gateway/router. Still nothing.
View 6 Replies
View Related
Aug 16, 2010
Our Sled 10.1 server is running as a VM on VSpher 4. After a power outage we can not log into the server we get the Error in Module message. I can however disable the nic card for the server in the vm console and the system logs in with no problem.
View 2 Replies
View Related
Nov 22, 2010
I've had a 4x 400Gb Raid 5 running for exactly 3 years now. There's been plenty of power outages in that time and lots of resyncing afterwards but all has been good afterwards with no issues. Last week after a power outage and reboot I went to check the status of the resync and it only listed 3 hdds.
[Code]...
View 3 Replies
View Related
Sep 23, 2010
I have downloaded linux mint using a USB followed all instructions and removed the USB stick as requested but it failed to boot on restart. it boots ok with the stick connected. i have changed it to boot from the hard drive and still no joy. i can access the terminal when the stick is on and all i need are the instructions to enable it to boot without the usb stick.
Samsung N210 10.1 inch notebook
1GB Ram
250 HDD
Came with windows 7 and i selected to use the whole disk when i installed Debian on it, the same when i installed mint and removed debian.
View 3 Replies
View Related
Aug 15, 2010
While I was installing some packages, the power in my street went out (uncleanly killing my system) ... unfortunately Kpackage was open at the time of the power outage. Now when I try to use KPackage, I get "Login Problem, Please Login Manually" ... which does not allow me to login using either the root or user's password. I have rebooted my computer many times and have even run a 'reiserfsck /dev/*** --fix-fixable' on my system, which did not repair the problem.
I have researched this error, but have only found responses that people suggest changing the KPackage behaviour from 'su' to 'sudo' ... ; while this does work, it feels like a 'putting-a-band-aid-over-a-warning-light-so-I-can't-see-the-warning-light-anymore' kind of 'fix?' which isn't good as it would enable anyone using the system to add or remove packages without thought or consequence. What I would prefer to do is actually fix the problem so that proper root password entering is again required to add or remove packages, so my question is:
1. Does anyone know if KPackage 'locks' out a file(s) on the system which may be preventing me from logging into the program correctly, and if so what and where the file(s) may be?
2. Can I delete any kpackage (profile?) file to gain normal login behaviour again?
3. Is this a permissions error?, has something in users/groups? been broken that I can look into?
4. how I may be able to properly repair this KPackage login problem on my system?
View 6 Replies
View Related
May 18, 2011
I am very new to linux, and I have a question regarding the filesystem check (fsck). The power recently went out and when I tried to restart linux the following error appears:
*/dev/sda1 contains file system w/errors, check forced it then goes on to say..
*An error occured during the file system check. Dropping you to a shell; the system will reboot when you leave the shell. Give root password for maintenance (or type Control-D to continue) I wasn't sure what to do, but checked some other online forums and they suggested running fsck manually - so I typed in the root password - and used the command, "fsck -A -V ; echo == $? ==" it then gave the following message
*WARNING!!! Running e2fsck on a mounted filesystem may cause SEVERE filesystem damage
*Would you like to continue (y/n)
Again, I wasn't sure what to do so i just checked no. I then manually turned off the computer and was prompted at the beginning to press Alt-3. I was brought to another screen and it informed me one of the drives was degraded and suggested rebuilding the array. I tried doing this, but it still brings me back to the original error of, "/dev/sda1 contains file system w/errors, check forced," and the process continues.
Also, when I tried to rebuild the array, I didn't backup any of the data on our home directory before doing this (which was probably a big mistake). After being prompted to type the root password, I was able to give the ls command and look at all the directories...the home directory where our data was stored was empty and I am afraid I may have lost some information. Is there a possibility that data was lost when I was trying to rebuild using the old drives?
View 2 Replies
View Related
Oct 10, 2010
come across with this issue for one server we are giving support please,help me to know why this issues occurs and alsothat i want a command to display power supplies for the server.please,let me know if anybody is familiar with these kind of issues.
View 2 Replies
View Related
May 15, 2011
I just completed a clean install and update of Fedora 14 on a Dell Precision 490 (4G of RAM, Dual Xeon 5140 CPUs).The system has all of the current updates applied and seems to be running normally, but it will not complete a shutdown/poweroff or restart. It gets hung with Restarting... in the upper left corner of the screen and stays there until I force the system to power down.I have searched quite a bit for related problems but have come up empty. Its kind of hard to debug because the system does not respond when it is in this hung state and there does not appear to be any relevant info in /var/log that I can find.
View 3 Replies
View Related
Oct 25, 2010
I have observed a problem twice now with Apache trying to restart but hanging somewhere in the process. This happens after a power failure; the machine comes back just fine, but not the web server. The machine is on a UPS, but occasionally it runs out of "juice" before someone can get to it (we have a generator for emergencies). When this happens, a ps indicates about three processes running that are trying to start Apache, but they just sit there - this time for three days since the power failure was on a Friday. I can fix this by killing those processes and doing an Apache restart - but that takes human intervention, which is not acceptable.
I suspect this may have to do with SSL, since when I do a manual restart it asks me for the SSL password. There must be some way around this so the system can recover on its own. This system's web site runs under SSL since it maintains medical information that must by law be protected. But it also could be life-threatening to someone if the system can't come back and as a result a person can't get help.
So I would appreciate some guidance as to what I could change that would allow for system recovery without intervention. I'm happy to provide any configuration file info, if you tell me where to look.
View 3 Replies
View Related
Dec 2, 2009
I play full screen video with maximum volume or browse the Web with WiFi.
Under Windows 7 my laptop works ~5 hours. Under Kubuntu 10.10 only ~2 hours.
I've got Acer Aspire 1810TZ. Battery wear degree 90%.
Installed:
acpid
acpi-support
pm-utils
[Code]....
View 3 Replies
View Related
Jul 24, 2011
I dual boot Ubuntu and Windows and sometimes I just want to switch between the partitions without loosing the state of the OS I was currently working with. Currently to do that I just hibernate that OS and, when the computer turns off, I restart it and select the correct partition.
I do not really want to have to press the on button again every time I want to switch between partitions. I figure that there must be a way to make the hibernate action restart instead of shutting down.
How do I make the hibernate action restart instead of shutting down on:
Windows, or Ubuntu
P.S. It is more important to me that I can do this in Ubuntu than Windows (because of the way I use the partitions) therefore if one answer says the Ubuntu way and the other says the Windows way then I will mark the Ubuntu one as the answer and give the Windows one an upvote and a big thankyou.
View 1 Replies
View Related
Jan 28, 2010
I am trying to figure out why, i need to restart/reboot ubuntu in order to reconnect wirelessly after being in power save mode. It works fine before the power-save mode and fine after the restart. Is it an IP issue?
View 1 Replies
View Related
