General :: Cant Read Filesystem Type On Windows Partition?
May 27, 2011
I had installed ubuntu 11.04 on my system along with windows vista. After a few days, i decided to remove ubuntu so i just logged into windows and formatted the ubuntu partition using the windows partitioner, then extended my main c: drive to span the whole disk so that i was left with a single partition with only windows vista on it.Later when trying to restart my system couldn't log back into windows.I kept getting a prompt sayinggrub rescue>After googling around a bit i shrinked and created another partition the disk again and installed ubuntu on it again.still. =/GRUB doesn't show any windows entry.I noticed something strange though that when i tried viewing my partitions using parted i didnt see any filesystem type listed besides my windows partition (/dev/sda3). I doubt that is why GRUB does not show any windows entry.Also i manually tried to boot into windows from the grub prompt using commands...root(hd0,3)chainloader +1bootbut it says 'invalid signature'Did i somehow corrupted my windows partition during resizing and installing/un-installing? Plus i also booted with the windows installation dvd and when i typed bootmgr /fixbootit said something like no valid filesystem found.
View 5 Replies
ADVERTISEMENT
Feb 27, 2011
As per these instructions, I got up to the end of the "Acquiring an Ubuntu filesystem" step (where it asks you to mount the newly created Ubuntu partition) and ran into a problem: The partition won't mount, as the file system type cannot be determined because I cannot remember the file system used during installation. Is there any command that prints the file system type of GPT partitions?
View 5 Replies
View Related
Feb 21, 2010
Formated new drive with ext3 on external drive on Suse 11.1 When upgraded to 11.2, drive was not connected... Could not get mounted after that... Set up another boot drive, could not get to mount. Found post with following:
>cryptsetup luksOpen /dev/sde1 restore
>mkdir /restore
>mount /dev/sde1 /restore
Error as follows: mount: unknown filesystem type 'crypto_LUKS' Have also got to another point where superblock was incorrect. I can use terminal, but am not a linux guru... Have looked at other posts under luks, but can not find a solution.
View 6 Replies
View Related
May 24, 2011
Until now I always used a non-journaled filesystem for my /boot-partitions.But as it would make system restoring much easier after crashes I would prefer to use ext3 for my /boot-partition as well.Is this possible, and before all, recommendable?
View 7 Replies
View Related
Mar 11, 2011
I am trying to mount a file image, like this
mount -o loop /tmp/apps.img /media/apps
But I get the following:
mount: you must specify the filesystem type
I try ext3:
mount -o loop /tmp/apps.img /media/apps -t ext3
dmesg says:
error: can't find ext3 filesystem on dev loop6.
I've also tried ext2, vfat etc. How can I detect the filesystem type of apps.img?
View 2 Replies
View Related
Feb 28, 2011
Anyone know why Linux has to share a partition type code (specifically, 0700) with Windows? Why can't it have its own like some other OSes?
View 4 Replies
View Related
Mar 24, 2010
I've had a look at some similar threads but as I'm very new to linux they're already a bit technical for me. Sorry, this calls for someone with patience. I gather from other threads that disconnecting an external drive without unmounting is a no-no, and this seems to be the likely cause. Now the disk is read only and I'm unable to change any settings through the usual control panel on ubuntu. I'm just not familiar with the terminal instructions. I tried to cut and past a few command lines from other threads but I got some warnings that proceding could damage data. Like this one: WARNING! Running e2fsck on a mounted filesystem may cause SEVERE filesystem damage.
View 5 Replies
View Related
Apr 1, 2011
I have a linux formatted partition. I'm trying to open that partition inside windows 7. And shrink it so that I can have more space. But all the options except delete and help are grayed out. What do I do?
Tried ext2explore but it seems it can only perform a copy of the whole partition.
View 1 Replies
View Related
Aug 28, 2010
I need a program that allows windows xp to read EXT4 partition. ext2explore.exe is not good, it doesn't give other windows applications direct access to ext4.
View 5 Replies
View Related
Mar 31, 2010
I installed fedora 12 and windows 7 in pc. i can not access fedora partitions from windows. which software is suitable for this?
View 8 Replies
View Related
Feb 4, 2011
In my system around 73gb(pc-desktop) i have,1 primary partition(windows)-25gb, 1-extended partition(remaining gb) 3 logical partitions were there in (under) extended partition in one of the logical partition is d:drive. in my hard disk d: drive is -/dev/sda5
previosly i was fat -file system , (d:drive-/dev/sda5), i remember i changed the d: drive(d:drive-/dev/sda5) file system to ext4file system ,with following command using terminal
After doing(changing the file system)this one ,i couldnt see the d:drive data
By doing that
1q) Did i reformatted the partition? i think the new filesystem(ext4) has no knowledge of the data that was on it when it had a FAT filesystem.
2q) How to do undo operation,i tried to change the filesystem type to fat/ntfs in terminal using command --sudo mkfs -t FAT /dev/sda5.
Result:its showing text message-'mkfs.FAT: No such file or directory'(not in single quote)
I had very imp data in d:drive
View 1 Replies
View Related
Mar 27, 2010
When I try to boot to OpenSUSE I get the following error during boot-up: unknown filesystem type 'reiserfs' could not mount root filesystem - exiting to /bin/sh$
This only started happening quite recently - before this I could boot to Linux quite happily.
View 6 Replies
View Related
Jul 9, 2010
I have a following problem: Recently my drive with Ubuntu 9.4 has mysteriously stopped working, i.e. when I switch the computer on it informs me that GRUB didn't find the filesystem. Well, I suppose it happens.
First, I though it was due to the drive dying, but I popped it in an external enclosure and HDTune told me the drive was fine. Wanting to recover the files on the drive before reinstalling I first tried to mount it in said external enclosure under Windows (I have Win Ext2 driver installed which used to work just fine). This time, however, drive gets assigned a letter but upon opening it Windows popped up an error saying that the drive was not formatted and whether I would like to format it then.
Unfazed by this streak of failures I tried to mount it under Linux but, alas, to no avail. I might have tried every single -t operator under mount command but it still won't budge and let me mount.
View 5 Replies
View Related
Mar 28, 2011
Code:
fsck from util-linux-ng 2.17.2
e2fsck 1.41.11 (14-Mar-2010)
/dev/sda1 is mounted.
WARNING!!! The filesystem is mounted. If you continue you ***WILL***
cause ***SEVERE*** filesystem damage.
Do you really want to continue (y/n)?
I don't want to cause damage, but I'd rather not go into BIOS.
View 6 Replies
View Related
Jul 7, 2010
I dont know anything about linux and just been assigned to amount a drive to it. here's what i did so far: Version of Linux using Red Hat Enterprise Linux Server release 5.3 (Tikanga) [root]# mount -t auto /dev/sdb1 /tmp/archive mount: unknown filesystem type 'ntfs'
when checking the /proc/filesystems, i noticed that 'ntfs' is not listed there, several forum suggested i try running 'modprobe ntfs'. If that is not found, you'll need a kernel with ntfs support. i'm so lost, where to i get the modprobe ntfs
View 2 Replies
View Related
Jun 21, 2010
What is the primary filesystem type used by Fedora 12 Linux?
View 7 Replies
View Related
Mar 6, 2010
ive been dual booting ubuntu and windows for a while now. For the first time in weeks ive booted windows XP, and i really hate the fact that windows explorer can't read more than the first partitions. Is there a way to make the explorer see more? I want to be able to reach my files on the ubuntu partition from windows, not just the other way
View 4 Replies
View Related
Nov 29, 2010
I have a spare harddrive that I want to store my videos on. They are in mp4 format. I'm using cfdisk to create a new clean partition on the drive. What filesystem type should i make it (linux,HPFS/NTFS,FAT16...)
View 2 Replies
View Related
Feb 19, 2011
I have been given a headless linux system running from a SD card. I get into it by putty, directly to root, not other user and even /home dir. Whatever I copy or write will dissapear because is ro.
my etc/fstab file is:
none /dev/pts devpts gid=5,mode=620 0 0
none /proc proc defaults 0 0
none /dev/shm tmpfs defaults 0 0
/dev/hda1 /boot vfatnoauto,rw 0 0
View 5 Replies
View Related
Jul 6, 2010
write a script that will check all filesystems to see if they are read-only.
I have come up with ...
df -h > /tmp/mount.lst
awk '{print $6}' /tmp/mount.lst > /tmp/mounted_systems.lst
This gives me ..
Mounted
/
/boot
/dev/shm
/proc
So now I have ..
How do I automatically get rid of the 'Mounted' header in my /tmp/mounted_systems.lst file ?
Also, I don't want to check the /proc filesystem, so how do I remove that within the script too.
Then I will run ...
while read dir
do
touch $dir/read_only_test
done < /tmp/mounted_systems.lst
If the filesystem is read only, I want that filesystem name to be listed into another file.
View 3 Replies
View Related
Oct 18, 2010
i've just installed the 11.3 while still keeping win 7. but i can't open the windows partition ,and even the massive usb storage device. i notice that by changing some syntax in the etc/fstba, i can make the system read the windows partition automatically once i start my PC. but how?
[Code]...
View 6 Replies
View Related
Mar 23, 2010
[Sorry if this is misplaced; I just couldn't think which category to put it under.] So yeah, I'm almost exclusively using karmic (yay!), but I still have to use that vista install I have smushed in a corner of my HD from time to time. Now, I installed karmic using the default, latest file system (ext4, I believe it is, right?). Last I remember hearing, that presents a bit of a problem, doesn't it?
View 5 Replies
View Related
Aug 19, 2010
I have a dual boot system and am trying to be able to access all partitions in both OSs. I've tried some windows software that are supposed to be able to read linux partitions, but without luck. Essentially, my linux OS (rhel) is represented as an LVM partition (within the logical volume is ext3). In windows (7), file viewing programs see the partition as "raw". Is there any software that can read LVM in windows?
View 1 Replies
View Related
Nov 28, 2010
I am running a dedicated server with linux cent os 5.5 32 bit with lighttpd, php 5.2.14 and mysql
I am getting problem in my server. The filesystem enters read only mode automatically and then I can't edit any file in my server. This happens by itself. I tried to run fsck command and it gives the following output:
Code:
[root@server]# fsck -A -y
fsck 1.39 (29-May-2006)
e2fsck 1.39 (29-May-2006)
/: recovering journal
Clearing orphaned inode 11108656 (uid=0, gid=0, mode=0140777, size=0)
Clearing orphaned inode 13631499 (uid=27, gid=27, mode=0100600, size=0)
[Code]....
View 2 Replies
View Related
Jul 16, 2011
I want my samba to keep my windows attributes exactly what the user setted in windows I mean if it has read only file in win box and copy it to samba share ,samba keep it read only and same for other attributes but it does not do it now with my configuration:Quote:
[global]
workgroup = DOMAIN
server string = File Server
[code]...
View 3 Replies
View Related
Oct 30, 2010
I've been using Ubuntu 10.10 for just under a week. Recently, a partition called 'Data' has disappeared, and all my music and documents along with it. The folder is not to be seen in Places or on my desktop. My only way of finding it is to go to terminal. But when I try to open it there I get an error saying I don't have permission to read it. In Puppy Linux and SliTaz I can easily find the partition and read it. What should I do to bring it back in Ubuntu?
View 3 Replies
View Related
Mar 16, 2011
I'm having difficulty making my FAT32 drive capable of read/write. I followed the instructions here (http://ubuntuguide.org/wiki/Ubuntu:Maverick#Windows_Compatibility) and added the following line to my /etc/fstab file:
Code:
/dev/sda4 /media/WinD vfat quiet,defaults,rw 0 0
However, when I rebooted the drive is still read-only
View 4 Replies
View Related
Jan 10, 2016
I have a Western Digital 3TB USB drive connected to a Raspberry Pi 2 running Raspbian Jessie. I created an 30GB ext4 system partition and a NTFS Data partition using the remainder of the drive. I formatted the NTFS partition as follows:
sudo mkfs.ntfs -Q -L Data /dev/sda2
The drive works fine on the Pi but when I connect it to a Windows 7 pc the pc doesn't recognise the format of the Data partition and can't access it.
On the Pi I ran:
$ sudo fdisk -l /dev/sda2
Disk /dev/sda2: 2.7 TiB, 2968557453312 bytes, 724745472 sectors
Units: sectors of 1 * 4096 = 4096 bytes
Sector size (logical/physical): 4096 bytes / 4096 bytes
I/O size (minimum/optimal): 4096 bytes / 4096 bytes
[Code] .....
Partition table entries are not in disk order.
View 14 Replies
View Related
Oct 16, 2010
I'm dual booting windows vista and ubuntu hardy on a multi-partitioned Dell D630. I created a partition using mkfs -t ntfs. Linux has no trouble reading/writing to it, but every time I boot into windows, chkdsk tries to "fix" the partition, fails, and tells me that the partition is corrupted. Can anybody suggest a way to convince vista that the partition is indeed ok, or else another way to create the partition so that vista can recognize it?
View 1 Replies
View Related
Mar 26, 2010
When i type the df command i see that /dev/hda1 as a filesytem that is mounted at '/'(root). Is /dev/hda1 a filesystem. I thought that it is a partition on my hard disk that contains the root file system.
View 6 Replies
View Related
