I am trying to install debian as a DC but on reboot I get the "Input not supported " error. I switched to virtual input and login to try to edit the xorg.conf file but created a new file instead because the xorg.conf file is open by the installation. How do I close it so I can edit it and continue. I am afraid to start a new file as I am not sure what is in the ools one.
View 2 RepliesAfter i edited my xorg.conf file to get 1280x1024 Resolution the font size in some programs is really big. [url]
View 2 Replies View RelatedCannot edit xorg.conf on Fedora13. I do it from the root but changes is not saving.
View 7 Replies View RelatedWhat is the command I use to edit the xorg.conf in fedora?
Achieve using the following command:
I am running Ubuntu 9.04 on an Acer Aspire laptop and have broken my display system while trying to use the restricted drivers for the nvidia graphics card.
Basically I downloaded and activated the restricted driver. I rebooted and now ubuntu freezes on startup.
I can get access to the command line but am unable to edit either fstab or xorg.conf because ubuntu has mounted the filesystem in read only mode.
I have read and tried all the options given in this posting [URL] but because I cant read or write any of the files I cant seem to affect any change to the system
i have a lenovo g550 with nvidia geforce g 105m i tried to install its driver on fedora 11 and 12 and i have followed the instructions of setup as in fedora sites and forums, the problem is after installation i have 6 equal screens 640*320 and i don't know how to edit xorg.conf
View 4 Replies View RelatedI've just done a fresh install of Lubuntu 10.10 on an older Sony Vaio laptop. Having learned the hard way about editing xorg files, I wanted to create a backup of the xorg.conf file so that I dont have to do another install when I screw everything up. In a terminal, I typed
[Code]....
I have installed Kubuntu 8.04.2 on a USB stick with persistence to keep any changes I make after a reboot and it works fine. I then installed the 185 Nvidia driver to give me higher resolutions and it works fine.
But each time I reboot, my updated xorg.conf is replaced with the default xorg.conf that ships with that version of Kubuntu and a backup is made of my updated xorg.conf (the correct one) which looks like xorg.conf.20100409135913. I have to put the backup xorg.conf back in place to get my Nvidia driver to work with the correct screen resolutions again. Otherwise my screen resolution is too low.
What could be causing this behavor? I'm sure it not the persistence feature of the USB stick failing since a backup is made of my original xorg.conf.
I might add more information. The xorg.conf that gets changed after a reboot says "This file was generated by dexconf, the Debian X Configuration tool, using # values from the debconf database." #
1. What is the difference between files (xorg.conf and xorg.conf-vesa)
2. No matter how hard I try I can't change keyboard layout in xorg.conf-vesa (I change it in file ) but there is no actually anything changing, it starts to get annoying - for example - below goes my xorg.conf-vesa, if I uncomment and set line from
[Code]...
I've read the how-tos (thank you oldcpu!) and wikis about how xorg.conf take precedence over the section configuration files in etc/X11/xorg.conf.d/, if it exist. I also understand that the xorg.conf can be partial. If it is missing some sections, these will be taken from the corresponding xorg.conf.d section config file. Currently I'm using a xorg.conf generated by nvidia-settings in one of my home machines, due to a dual-monitor setup. After generating xorg.conf, the device sections are:
in xorg.conf:
Code:
Section "Device"
Identifier "Device0"
Driver "nvidia"
[code]....
My question is if the Option "UseCompositeWrapper" "True" will be used or not. In other words, if a section exist in xorg.conf then it's correspondent in xorg.conf.d/ will be completely ignored *or* only the lines in xorg.conf.d/ that already exist in xorg.conf will be ignored?
I'm running the ubuntu based Green OS and cant get my video card properly configured. i've already gone through the forums to figure out what i need to do to get my ATI card working but my system wont let me access the xorg.conf file. i can see it using the the GOS file editor but it wont let me save the modifications. when i attempt to edit from a terminal window with su privelages it tells me that /etc/x11/xorg.conf does not exist. i've even tried booting into recovery mode and using the root instead of the sudo command. nothing i've tried will let me open the file.
View 3 Replies View Relatedfglrxinfo= "display: :0.0 screen: 0
OpenGL vendor string: ATI Technologies Inc.
OpenGL renderer string: ATI Radeon HD 5450[code]......
I have used nVidia my entire linux life (about 5 years clean and sober from M$). Recently, I have switched over to an ATI Radeon HD 5550 card. After many trial and error setups, I finally got the resolutions and screens set properly with a xrandr command, which I have now added to a shell script in ~/.kde4/Autostart. It has worked for me for a while now, but I really would like to get it set in the xorg.conf.d files so that I don't have to wait that extra few seconds after login for the screens to fix themselves.
Is there an easy way to take what xrandr does and export it to the xorg.conf.d files? If my video card recognizes my default monitor as DFP2 and the tv that I only sometimes use with this computer as DFP1, how can I ensure that the login screen for openSUSE/KDE4 appears on my default screen (an issue that drove me nuts a few months ago when I tried Ubuntu to see what all the fuss was about)?
My xrandr command that I use to fix it all is:
xrandr --output DFP2 --auto --pos 0x0 --primary --output DFP1 --auto --right-of
I am using the proprietary Radeon driver from the ioda repository. DFP2 is a monitor which has a optimum resolution of 1920x1200, and DFP1 is an 1080p HDTV. I can not reverse the output plugs for the screens even though my monitor is an HDMI monitor because I use the actual HDMI port on the video card to output audio to the television and the other plug is a DVI that I convert to HDMI for the monitor.
My setup is: Debian Lenny 5.0.4 I have an ATI Radeon X1200 series (embedded in the motherboard).What version of the ATI official drivers do i need? I recall that i was having troubles with the latest drivers, because ati has dropped support for these products. Another question is: Does Lenny 5.0.4 will work with the previously mentioned graphics card, or they had upgraded the version of Xorg to an unsupported one?
View 14 Replies View RelatedI have the following section in xorg.conf
Section "Device"
Identifier "Default Device"
Driver "fglrx"
EndSection
In what directory does it look to find the fglrx driver?
I had some problems because I changed my display resolution. Finally I changed the /etc/x11/xorg.conf file to:
Now the monitor is not recognised any more.
[url]
I have fedora.
Is it possible to add more than one graphic device driver to xorg.conf and it will load automatically? It is important to autodetect because I am using the configuraiton read only. This is because it's a custom LIVE CD.This is what I currently have, and it works!
Problem is if I put my Live CD in my brothers machine, it fails to load because it uses a Radeon driver!I can preinstall the ati packages I need, so all i need to know is how do I make it work?
I am using Linux 2.6.29-020629-generic #020629 SMP Tue Mar 24 12:03:21 UTC 2009 i686 GNU/Linux ubuntu.
I have a widescreen lcd laptop and the current resolution is set at 1280x768 pls see output of xrandr here for more information [url]
I want to change the resolution to 1024x768. I can do in ubuntu' display tool. The problem is that once I change it, the output does not take up the whole screen it has blank spots on the left and right side
For a better understanding please have a look at [url] and [url]
In open suse the system sets it at 1024x768 without any blanks on the left and right corner. You can have a look at it here [url].
My current xorg.conf is details is at [url].
Please also find my xorg.0.log at [url]
The lcd does not have any controls to tweak.
When X.org boots up, Synaptics touchpad works well. But when I remove the module it falls back to /dev/input/mice and don't use normal driver even when touchpad is available again.
Xorg.0.log:
...
(II) XINPUT: Adding extended input device "Synaptics Touchpad" (type: TOUCHPAD)
(--) Synaptics Touchpad: touchpad found
# { rmmod psmouse && echo mem > /sys/power/state && modprobe psmouse; }
(WW) : No Device specified, looking for one...
(II) : Setting Device option to "/dev/input/mice"
...
How to tell X.org to try it's InputDevice again (without restarting X server)? rmmod psmouse is needed to prevent crashing of Acer Extensa 5220 when resuming from suspend-to-ram. Found answer myself: Doing xinput set-int-prop "Synaptics Touchpad" "Device Enabled" 8 1 after reloading the kernel module reloads touchpad. Now suspend-to-ram works OK.
Like in xte "str ў", but with support of all characters.
View 1 Replies View RelatedMy Dell Precision Workstation was shipped in 2003 with RH Linux installed (most likely RHEL 4) - though not sure.
At the time, the dual monitors worked by replacing the X86config file with one sent from Dell.
Since, my disk failed and I had to replace the disk and reinstall RH Linux with the shipped disks, RHEL 5.
Now, I can not find X86config; rather, I have been trying to update the Xorg.conf file with no to limited success.
Both monitors are driven off of one Nvidia Quadro FX 1300 videocard. My goal is to get the screen to span both.
Does anyone have a Xorg.conf file that would support this?
Been trying to setup my xorg.conf file to have a 1920x1200 screen.Strange behavior: when my X starts up, I see my mouse cursor, can move it around. It's small enough to suggest the 1920x1200 resolution took, is working.However, the rest of the screen remains black. No login prompt.I've looked at /var/log/xorg.conf, no errors.Is there something else I can look at?
View 1 Replies View RelatedCan anyone help with me configure my dual-screen monitors for rotation? I have xrandr 1.1. Have tried various approaches, nothing takes. I can't even get the xrandr options to show up in KDE's Display control panel.
My lspci output: 03:00.0 VGA compatible controller: ATI Technologies Inc RV516 [Radeon X1300/X1550 Series] My current xorg.conf (works, minus screen rotation): # Xorg configuration created by system-config-display
Section "ServerLayout"
Identifier "Multihead layout"
Screen 0 "aticonfig-Screen[0]" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
Option "Xinerama" "off"
[Code]...
I have set up my Ubuntu virtual machine and am trying to adjust the screen resolution because it's stuck at 800x600 presently and there are no higher resolution options. I've looked at numerous similar forms and tutorials online and they all seem to involve editing /etc/X11/xorg.conf. However, for whatever reason, this file seems not to exist on my machine. I found another tutorial on how to add a screen resolution using xrandr --addmode which added the resolution I want to the list that appears when I type the command xrandr, but when I try to apply it I get an error about CRTC 262 failing.
View 8 Replies View RelatedI've been getting a message on my monitor where "Input not supported" is floating around. This only happens when I manually turn the monitor off and then later turn it back on. Leaving the monitor on and allowing it to go to the screen saver doesn't seem to cause the issue (but I prefer to turn the monitor off if I'm going to be away from the computer for any length of time).
Specs:
Acer X203w monitor
Radeon 9600 Pro Video card
Linux Mint 8 (Helena)
Resolution 1680 x 1050 (16:10 - Preferred native resolution for the monitor)
Refresh Rate 60hz
[Code]...
I just had it happen again. I tried unplugging the DVI cable from the back of the computer and then plugging it back in. The monitor then displayed the desktop properly. I'm not sure if that makes a difference or not in what I may need to change settings-wise.
Up through Slackware 13.0 I used xorg.conf without trouble. On Slackware 13.1 I am caught between two unacceptable alternatives. If I don't use xorg.conf at all I can't adjust the screen density between e.g., 640 x 480 and 1024 x 768 by hitting <ctl><alt>+ or <ctl<alt>- If I use the same xorg.conf that I have used for years I gain the above facility but when I go to a console session via <ctl><alt>F1 the monitor complains that it is being fed bad information. If I can't resolve this conflict I will have to retreat to Slackware 13.0.
View 2 Replies View RelatedSorry if this was well covered here when most up-to-date Slackers moved to 13.0, but I have just jumped from 12.1 to 13.1. Generally very happy that I do not have to think about xorg.conf as I always found the structure of this conf file a tad confusing. However if I do need to (for example) change my video driver (I might for example want to try the nvidia driver from NVIDIA) or configure my touchpad - how do I do this ?
I understand that xorg.conf can still be created. If I do so, do I have to put all the stuff in that used to be there or can I just add the stuff I need to make the changes I am looking for?
i i use ubuntu 10.04 and i buy a mouse, and i cant install it. i read on forum i need to put :
Section "ServerFlags"
Option "AllowMouseOpenFail" "true"
EndSection
[code].....
wireless via Bluetooth � 3-button laser mouse with scroll wheel � resolution 1600dpi, adjustable on 800dpi � range up to 10m � computer with Bluetooth or dongle required � 2x AA batteries required
i lost touchpad functionality during gdm login (i cant tap clicking) after playing with xorg.conf
would somebody kindly paste-ing their xorg.conf for eee pc (1000HE) ?
I just did a net install on an old powerpc G4 and it seems pretty successful.except i cant change any of the monitor settings from the control panel in gnome (or LXDE)its showing 'not recognised' and only allows 768 x 1024 in very restricted colour.I dont think there is a hardware problem:
- the monitor is a generic old CRT which has worked fine with everything before this.
- the display card is an AGP 32Mb - original with this G4 and was working.
- the computer works great in Mac OS10.3 - (but OS10.3 doesnt support flash or up to date web browser any more, hence trying debian).
i have searched debian forums and various sites, but i couldnt find a fix. It looked like i should edit xorg.conf file but I am not able to find it. I looked in /etc/X11 - but not there.could someone tell me please, do i need to find xorg.conf?