I want to block all the outgoing ssh form my machine, i.e my machine will not be able to ssh to any outside machine using iptables. The distro is RHEL, I added the following entry in the iptables but unfortunately it didnt worked, -A OUTPUT -p tcp -m tcp --dport 22 -j DROP
View 13 Repliesi used the angry ip scan software and found alot of the public ip addresses on our network are accessable from outside when they are not suppose to, For eg printers/ pcs etc. to make a start on locking down the network i was wondering if anybody knew th iptables command to add a rule which blocked all incoming traffic to specific ip adresses on the network and to a range of ip addresses.
View 7 Replies View RelatedMobloquer starts up at boot and before I've even opened firefox or transmission or anything, mobloquer shows that is has started blocking several outgoing connections as well as ton of incoming connections. I was wondering if the outgoing connections is normal and what's a normal amount of network activity to show up in system monitor when I'm not actively using the internet.
View 2 Replies View RelatedI want to block all outgoing traffic with iptables and only allow a few specific websites. I would like to get the code to do so and also to revert the changes in case I want to unblock them.
View 1 Replies View RelatedUnsure about IP tables lingo, so excuse me for not looking this up:I have a server, running IP tables, that I do not want to allow any type of outgoing traffic to 192.168.1.21
View 3 Replies View RelatedRather new to Ubuntu. I was wondering for advice on a basic iptables configuration blocking all incoming/forward and just allowing outgoing to http(s) and dns of course.
View 5 Replies View RelatedI've been trying to redirect all outgoing packets (destined for a specified ip address) from my slack box back to itself. I thought this could be done with iptables, but if I fire up wireshark I can clearly see that the packets are getting out to the real server and I'm getting responses from it.
So here's what I tried:
All looks good and fine, and then I even try to visit 194.28.157.42 with firefox (by the way I am running a webserver, that is set to show a page when you visit 127.0.0.1) and I get an error page that reads: 502 Bad Gateway.
I ignored this message to see what the program I'm trying to interrupt does, and when I start wireshark and then start the program that is using that website, I can clearly see that the packets make it to the real 194.28.157.42 and get back responses.
I need to know what the Iptables "code" is to change the outgoing/Incoming IP for port 53 (DNS). I'm running CentOS on a dedicated server. I very familiar with Putty and SSH. So I don't need much details, I just can't figure this out. I asked my server providor but they deleted my ticket and didn't answer me.I tried this but am not sure if this correct of working?
View 5 Replies View Relatedit�s been several years since i played with iptables. I have setup like this:eth0 is the only physical device on box and eth0:0 is aliased. Traffic going out of the box to internet uses eth0eth0 116.55.58.1eth0:0 116.55.58.2I have a service listening on port 80 on 116.55.58.2Lets say my client connect to 116.55.58.2:80 through 116.55.58.1 , how do I force (mangle you name it) with iptables that the outgoing source address will be always 116.55.58.2?
View 1 Replies View RelatedAs too my question, at this time I dont control the router/firewall an I would like to block a port thats used for guild wars on my workstation for a while. The reason for blocking is children have abused it an lost it.In this case I am trying to block outgoing traffic on port 6112. I have tried setting up a proxy server on the workstation, but the game seems to ignore it an jump on. Due to the environment, I enabled the workstation SuSEFirewall2 firewall an tried setting up "lo" as a internal an configure the firewall as a router, then disable 0/0 an configured for 0/0,tcp,443 an re route port 80 traffic to proxy.
When I had my own internet, I had a transparent proxy enforcing rules for access times. So setting up a proxy on each machine would not be a bad thing, even if it took some creative thinking. I am trying, but seem to be missing something.Ideally, I would like to setup a transparent proxy, as my kids have learned alot about system administration an know to check the proxy module. If all they have to do is un check "Use Proxy" an by pass a local proxy server, then I am kinda defeated. An applications such as firefox have a proxy setting they could set to none instead of system
I want to block the icmp packets(ping) from the other computer to my RHEL-4 what's the syntax I should use to do so in IPTABLES.
View 2 Replies View RelatedIs possible blocking web with content for adults with iptables?
View 3 Replies View RelatedI need to configure iptables to block incoming traffic (except specific ports), but allows all outgoing traffic.
I am able to block incoming traffic, but doing so also prevents outgoing traffic (tested by telnet [URL] 80)
The following was used:
iptables -A INPUT -p tcp --dport ssh -j ACCEPT
iptables -A INPUT -p tcp --dport 80 -j ACCEPT
iptables -I INPUT 1 -i lo -j ACCEPT
iptables -A INPUT -j DROP
Also, even allowing NOT SYN requests still prevents outgoing traffic.
iptables -I INPUT 1 -p tcp ! --syn -j ACCEPT
Another point:
# modinfo ipt_state
modinfo: could not open /lib/modules/2.6.18-028stab070.14/modules.dep
How to install ipt_state module on ubuntu?
Friends the following shall block a particular machine in the same network, what can be done if it is dynamic IP and from other network?
iptables -A INPUT -s 192.168.0.0/24 -m mac --mac-source 00:50:8D:FD:E6:32 -j DROP
I am setting up a iptables firewall on one of our servers, and I would like to block a range of addresses from getting into the system. I am using a script that does a BLACKIN and BLACKOUT methodology for specific addresses. One example is the following:
Code:
$IPTABLES -A BLACKIN -s 202.109.114.147 -j DROP
...
$IPTABLES -A BLACKOUT -d 202.109.114.117 -j DROP
What would be the correct syntax to use if I wanted to block an entire remote subnet from getting into the server?
I set up iptables but it is blocking my SSH set up. I did allow it by opening port 22 but it did not work. Here is my config:
Code:
iptables -F
iptables -P OUTPUT ACCEPT
iptables -P INPUT DROP
iptables -P FORWARD DROP
### this should allow SSH traffic
iptables -A INPUT -p tcp --dport 22 -j ACCEPT
iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT
How do you allow SSH through the iptables firewall?
I've got a box with 2 interfaces, with IP1 = 192.168.100.1 and IP2 = 10.1.1.1 respectively on them. I've got an iptables rule that looks like:
Code:
iptables -t nat -A POSTROUTING -s 192.168.100.0/24 -d 10.0.0.0/8 -p udp -j SNAT --to-source 10.1.1.1 --random
If I get 2 consecutive packets from the same address and port from 192.168.100.0/24, they get SNAT-ed and come out of the same port on 10.1.1.1. If then I get another packet from the same address and port 10 minutes later, then it gets SNAT-ed, but comes out of a different port on 10.1.1.1. My question is: how can I set the time delay I would like iptables to remember its incoming address/port to outgoing port mappings?
i need is to have http and https allowed, together with mail server (incoming and outgoing) and ftp, ftps and ssh. all other ports have to be closed.
View 3 Replies View RelatedMy Ubuntu Box has 3 interfaces. eth0 (Internal 192.168.1.0/24)eth1 (External ISP DHCP)eth2 (External ISP Static IP)I need the outgoing traffic to internet for 1 of the internal pc (192.168.1.10) to only go only go through eth2
View 4 Replies View RelatedI have two asterisk servers each one behind a linux firewall/gw. Linux is Centos 5.4, kernel 2.6.18-164.el5, iptables v1.3.5. Routes on the fws are ok and when iptables is stoped the servers are see each other, all good. But when I run iptables script in any fw, one server (not always the same) goes unreachable. I verify this with asterisk -r, then show sip trunk, and status becomes UNREACHABLE.
Iptables scripts is generated by fwbuilder. The weird part is I put only one rule to de script and it looks like Source=any, Destination=any, Service=any, Interface=any, Direction (Inbound,Outbound)=any, Time=Any, Action=ACCEPT. So as you can see I tried something like "Do not do anything at all". But anyway I run the script in any fw and one server becomes UNREACHABLE. I think the script does something wrong after all or maybe I have some missconfiguration in my asterisk conf files. The point is I am not so expert in iptables or shell scripting so I can't see anything in the iptables script. I have look for some issues like iptables blocking because of ip_conntrack table full, or "dont fragment" bit set in kernel problem, but nothing seems to be the right problem at all.
I have a fiberoptic broadband 20MB synchronous pipe at my home. Over summer at my place of employment its pretty much dead for 3 months so when I'm not busy I play around on my home server. I have my 20mb pipe going directly into my wrt54gl, from there I have a wired connection going to my server (Centos 5.3 recently upgraded to 5.5 through updates.) It serves as a file server(Samba, SSH). My wrt54gl handles natting port 22 to my server. I have my wireless AP setup to hand out leases from .2-.20 and my server has a static of .100. Dyndns.org handles my name resolution via their free account method.
I have a Mac Pro, iMac, Macbook, and a Toshiba Laptop with 64bit 7 running off wireless along with our cell phones, and my XBOX 360 also is wired directly for the gaming speed. I use all of the computers around my home to access the samba shares via unc path for file sharing and or working on projects. I had originally planned to upgrade the wrt54gl with a cisco e3200 or an e3000 but unfortunately I've come to find out dyndns and the e lines of cisco wireless AP's dont work with dyndns and get banned. So I would have to install the daemon on my server and put it as a directly connected server to my WAN link and install a second ethernet card and pass traffic through my server for the rest of my home which I am not going to do.
All of the previous sentence because it would update dyndns with a 192.168.x.x address since its not directly connected. I use a combination of putty.exe and vnc viewer to tunnel 5900 through port 22 to my server. So from anywhere I am at I can access my screen securely and then rdp or vnc to the desktop of my local LAN computers. This allows me to only have port 22 open. I've been looking at my ssh logs and noticed I have been getting hit alot with ssh scans. I want to implement an iptables firewall on my linux machine just for the purpose of further securing port 22. I dont necessarily need natting on the iptables firewall but all I need is ssh in and out, web in, and samba out to local ip's only.
For SSH this is what I want. I want to allow SSH from any IP but if it tries to login more than 3 times in one minute I want to block that IP for a full minute before it can try 3 more attempts. I also would like log to a file but have been having issues getting that to work as well. That way when I review logs and I see that an ip tries three times and then waits a minute and tries three more, etc... I can permanently block that ip or range of ip's by adding it to the iptables script. Here is my current iptables script and it doesnt seem to be working for me. I have played with this and read for almost two weeks and still cannot get it to work correctly.
Code:
#!/bin/bash
# In order to use this iptables firewall script you must have iptables installed. You also must be using a 2.4.x series Kernel, with iptables suppport compiled into it, which is standard for most newer linux distributions.
# If you need help compiling iptables into your kernel, please see our kernel Compile/Upgrade Guide located at [URL]
# Once the script has been edited with all your relevant information (IP's Network Interfaces, etc..) simply make the script executable and run it as root.
# chmod 700 fw_rules.sh
# ./fw_rules.sh .....
# Our final trap. Everything on INPUT goes to the dropwall
# So we don't get silent drops.
$IPT -A INPUT -j dropwall
When i was try to execute this command in my router device it will show error...
First execution:-
Second Execution:-
So I Need to block this kind of websites ...kindly tell me what i have to rectify & change..here i didnt execute this command...
I am currently running Debian 6. I would like to know if there is a way and how i would go about blocking a certain IP range from connecting to my server within a certain port range. Say for example.
i want to block ip range 123.123.123.* from connecting to my server on the ports 33000 - 43000. But, i want to allow them to connect on any other port range, and i want to be able to allow connections from my server to the blocked ip range on those same ports. so, blocking incoming only on the above port range.
using iptables.
I am at a loss how to prevent Denial of Service attacks to port 25 and not block legitimate connections from 2 Barracuda 800(s) and block smart phones such as iPhones/Blackberrys/iPhones that use the server smtp.server.com for email.
Presently for port 25
RH-Firewall-1-INPUT -p tcp -m state --state NEW -m tcp --dport 25 -j ACCEPT
The 2 Barracuda 800(s) make port 25 connections all the time, plus users with smart_phones have the incoming server type:
IMAP
pop.server.com
smtp.server.com
Is there a way to keep Denial of Service attacks from happening with iptables rules without causing blocking to the Barracuda(s) that make constant port 25 connections & smart phones that poll? I was thinking if I allowed the Barracuda(s) in these lines
-s (barracuda)24.xx.xx.xx -d (emailserver)24.00.xx.xx -p tcp -m tcp --dport 25 -m state --state NEW -j ACCEPT
Where the source would be the Barracuda going to the email server. It would be allowed, then I am left with how to allow other connections like Smart_Phones that connect via Port 25. I am thinking if I put rules in place doing connection counts in a minute it would result in errors connecting to the server and people would start complaining. Plus any limiting may result in blocking real traffic. Then would I need to allow the ISP range in the above example to accept port 25, I am still left with how to drop a flood/denial of service attack.
For system calls, is blocking or non-blocking default in C? Simple question, just am not seeing the answer super quickly.
View 4 Replies View RelatedI have a device that is working on modbus protocol andI have written a small program(with block TCP read method ) to read its registers via modbus protocol.my program is working very well but except those times that I unplug the Ethernet cable or turning off the modbus gateway during programs work.at this time my program stops on recv system call (if it reach this system call exacly when I unplug Ethernet cable or turning off the modbus gateway during programs work).I changed my source to work in nonblock TCP method, at this time with the same situation my program does not stop/block on recv system call but after pluging back the Ethernet cable or resuming the connectivity situation back it reads data incorrectly .this is my code:Quote:
#define DEBUG
#include <fcntl.h>
#include <string.h>
[code]...
I am facing a strange problem witht my iptables as there are some firewall entries stored somewhere which is displaying the below firewall entries even after flushing the iptables & when I restart the iptables service then the firewall entries are again shown in my iptables as shown below,
[root@myhome ~]# iptables -L
Chain INPUT (policy ACCEPT)
target prot opt source destination
[code]....
How do I check/setup that only the server can send mail (maybe by IP or hostname)? I have a debian server that sends mail through the PHP mail() function with no problems. The server uses sendmail. My concern is how do I make sure only the server itself can send mails through that server. Because it would be bad if spammers would use it as a relay server.
System:
- Debian Lenny
- PHP5
- Apache2
- MySQL 5
- PHPmyadmin
- Sendmail
Our organization has several external IP addresses. I am behind 2 layers of NAT and the servers choose which IP address to route my traffic to. Can I specify which IP address to use when finally leaving the organizations network. I know that source routing can be done in IPv4 by adding some options in the header. But can I configure my PC to add these options automatically. I have both a Windows and a Linux Machine.
View 1 Replies View RelatedI am looking to be able to encrypt using OpenPGP certain outgoing emails on my linux server. Currently I have GPG setup with a public key, however encryption outgoing emails prooved to be harded.After a bit of research I have found GNU Anubis which acts as a middlemad between the MUA and the MTA, by encrypting emails before they reach my MTA (Sendmail)However I am having a bit of problem with the configuration of bind and remote-mta, as specified by anubis.I have the sendmail service running on port 25 and I want to leave it there, but I have configured my php.ini SMTP port to 24. So it runs through port 24 first and anubis then forwards the emails via remote-mta to port 25Here are my anubis configs:
bind localhost:24
local-mta /path/to/my/sendmail
remote-mta localhost:25
With all those set, I can't seem to get the basic modication of emails to work. (trying to change a certain subject to something else, just to see that anubis is working). However emails are still working with port 24 as the SMTP port.